Do not trace arch_local_save_flags(), arch_local_irq_*() and friends.
Although they are marked inline, gcc may still make a function out of
them and add it to the pool of functions that are traced by the function
tracer. This can cause undesirable results (kernel panic, triple faults,
etc).
Add the notrace notation to prevent them from ever being traced.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we clone the SKB, we forget about the original
one. Avoid this problem by using skb_share_check().
Reported-by: Penttilä Mika <mika.penttila@ixonos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM6467 and DM6467T EVMs use different reference clock
frequencies. This difference is currently supported by having
the SoC code call a public board routine which sets up the reference
clock frequency. This does not scale as more boards are added.
Instead, use the clk_set_rate() API to setup the reference clock
frequency to a different value from the board file.
Suggested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Unfortunately we have to use a real modulus here as
the multiply trick won't work as effectively with cpu
numbers as it does with rxhash values.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1475) adds device_lock() and device_unlock() calls to
the store methods for the power/control and power/autosuspend_delay_ms
sysfs attribute files. We don't want badly timed writes to these
files to cause runtime_resume callbacks to occur while a driver is
being probed for a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM documentation and kerneldoc comments sometimes spell
"runtime" with a dash (i.e. "run-time"). Replace all of those
instances with "runtime" to make the naming consistent.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM documentation in Documentation/power/runtime_pm.txt
doesn't say that pm_runtime_enable() and pm_runtime_disable() work by
operating on power.disable_depth, which is wrong, because the
possibility of nesting disables doesn't follow from the description
of these functions. Also, there is no description of
pm_runtime_barrier() at all in the document, which is confusing.
Improve the documentation by fixing those issues.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the roles of the PM core is to prevent different PM callbacks
executed for the same device object from racing with each other.
Unfortunately, after commit e866500247
(PM: Allow pm_runtime_suspend() to succeed during system suspend)
runtime PM callbacks may be executed concurrently with system
suspend/resume callbacks for the same device.
The main reason for commit e866500247
was that some subsystems and device drivers wanted to use runtime PM
helpers, pm_runtime_suspend() and pm_runtime_put_sync() in
particular, for carrying out the suspend of devices in their
.suspend() callbacks. However, as it's been determined recently,
there are multiple reasons not to do so, inlcuding:
* The caller really doesn't control the runtime PM usage counters,
because user space can access them through sysfs and effectively
block runtime PM. That means using pm_runtime_suspend() or
pm_runtime_get_sync() to suspend devices during system suspend
may or may not work.
* If a driver calls pm_runtime_suspend() from its .suspend()
callback, it causes the subsystem's .runtime_suspend() callback to
be executed, which leads to the call sequence:
subsys->suspend(dev)
driver->suspend(dev)
pm_runtime_suspend(dev)
subsys->runtime_suspend(dev)
recursive from the subsystem's point of view. For some subsystems
that may actually work (e.g. the platform bus type), but for some
it will fail in a rather spectacular fashion (e.g. PCI). In each
case it means a layering violation.
* Both the subsystem and the driver can provide .suspend_noirq()
callbacks for system suspend that can do whatever the
.runtime_suspend() callbacks do just fine, so it really isn't
necessary to call pm_runtime_suspend() during system suspend.
* The runtime PM's handling of wakeup devices is usually different
from the system suspend's one, so .runtime_suspend() may simply be
inappropriate for system suspend.
* System suspend is supposed to work even if CONFIG_PM_RUNTIME is
unset.
* The runtime PM workqueue is frozen before system suspend, so if
whatever the driver is going to do during system suspend depends
on it, that simply won't work.
Still, there is a good reason to allow pm_runtime_resume() to
succeed during system suspend and resume (for instance, some
subsystems and device drivers may legitimately use it to ensure that
their devices are in full-power states before suspending them).
Moreover, there is no reason to prevent runtime PM callbacks from
being executed in parallel with the system suspend/resume .prepare()
and .complete() callbacks and the code removed by commit
e866500247 went too far in this
respect. On the other hand, runtime PM callbacks, including
.runtime_resume(), must not be executed during system suspend's
"late" stage of suspending devices and during system resume's "early"
device resume stage.
Taking all of the above into consideration, make the PM core
acquire a runtime PM reference to every device and resume it if
there's a runtime PM resume request pending right before executing
the subsystem-level .suspend() callback for it. Make the PM core
drop references to all devices right after executing the
subsystem-level .resume() callbacks for them. Additionally,
make the PM core disable the runtime PM framework for all devices
during system suspend, after executing the subsystem-level .suspend()
callbacks for them, and enable the runtime PM framework for all
devices during system resume, right before executing the
subsystem-level .resume() callbacks for them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
A subsequent patch is going to move the invocation of
pm_runtime_barrier() from dpm_prepare() to __device_suspend().
Consequently, early wakeup events resulting from runtime resume
requests for wakeup devices queued up right before system suspend
will only be detected after all of the subsystem-level .prepare()
callbacks have run. However, the PCI bus type calls
pm_runtime_get_sync() from its pci_pm_prepare() callback routine,
so it would destroy the early wakeup events information regarding PCI
devices. To prevent this from happening add an early wakeup
detection mechanism, analogous to the one currently in dpm_prepare(),
to pci_pm_prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Followup to commit f82528bc13 (Exclude duplicated checking for
iface-up) : We no longer need percpu tx_dropped field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support of ALC269VC codec.
Also delete the unnecessary codec_variant type enum list:
now only three variants (ALC269VA ALC269VB ALC269VC) are needed.
In addition, added some aliases:
- Add ALC269VB alias name ALC277
- Add ALC269VC alias name ALC259 ALC281X
- Add ALC269VC for Lenovo device 0x21f3 name ALC3202
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set up a correct I2C bus controller variant name for Exynos4.
Without this change the I2C bus driver fails to acquire its
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add an unsolicited notification of the DCBX negotiated
parameters for the CEE flavor of the DCBX protocol. The notification
message is identical to the aggregated CEE get operation and holds all
the pertinent local and peer information. The notification routine is
exported so it can be invoked by drivers supporting an embedded DCBX
stack.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following couple of patches add dcbnl an unsolicited notification of
the the DCB configuration for the CEE flavor of the DCBX protocol. This
is useful when the user-mode DCB client is not responsible for
conducting and resolving the DCBX negotiation (either because the DCBX
stack is embedded in the HW or the negotiation is handled by another
agent in the host), but still needs to get the negotiated parameters.
This functionality already exists for the IEEE flavor of the DCBX
protocol and these patches add it to the older CEE flavor.
The first patch extends the CEE attribute GET operation to include not
only the peer information, but also all the pertinent local
configuration (negotiated parameters). The second patch adds and export
a CEE specific notification routine.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver didn't set this parameter on the ETHER, the CPU will
encounter the "data address error" exception.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link was down, the bit of DM in ECMR was always set.
So, we could not use half-duplex mode on the controller.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing macro fails for following scenarios.
1) S5P64X0 channel 1
2) S5PV210 channel 1
The FIFO data level supported in the above SoCs either 64 or
256 bytes depending on the channel. Because of this the TX_DONE
is the 25 bit in the status register.
The existing macro works for the following scenarios
1) S3C6410 all channels
2) S5PC100 all channels
The FIFO data level supported in the above SoCs 64 bytes
on all the channels. Because of this the TX_DONE is the 21 bit
in the status register.
So when we use the existing macro for the non-working SoCs
it is not anding with the TX_DONE bit for transmission status check.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
tx_st_done is required for checking the transmission status of SPI
channels with different fifo levels
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert a printk with a static to pr_<level>_once
Add and use DRV_DESCRIPTION to reduce string duplication.
Remove now unused version.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just add GSO to vlan_features initialization, and update comments.
When we set offload features, vlan_dev_fix_features() will do more check.
In vlan_dev_fix_features(), final features is decided by
features of real device and vlan_features of real device.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->rxhash cannot be properly computed if the
packet is a fragment. To alleviate this, allow the
AF_PACKET client to ask for defragmentation to be
done at demux time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fanouts allow packet capturing to be demuxed to a set of AF_PACKET
sockets. Two fanout policies are implemented:
1) Hashing based upon skb->rxhash
2) Pure round-robin
An AF_PACKET socket must be fully bound before it tries to add itself
to a fanout. All AF_PACKET sockets trying to join the same fanout
must all have the same bind settings.
Fanouts are identified (within a network namespace) by a 16-bit ID.
The first socket to try to add itself to a fanout with a particular
ID, creates that fanout. When the last socket leaves the fanout
(which happens only when the socket is closed), that fanout is
destroyed.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix regression occurring during device removal
USB: fsl_udc_core: fix build breakage when building for ARM arch
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Add Makefile and Kconfig Entries for tps65911 comparator
mfd: Fix build error for tps65911-comparator.c
Revert "mfd: Add omap-usbhs runtime PM support"
input: pmic8xxx-pwrkey: Do not use mfd_get_data()
input: pmic8xxx-keypad: Do not use mfd_get_data()
If gso/gro feature of underlying device is turned off，
then new created vlan device never can turn gso/gro on.
Although underlying device don't support TSO, we still
should use software segments for vlan device.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced the handrolled bubblesort with the kernel's sort() function.
Makes things considerably smaller & clearer.
Signed-off-by: Chris Forbes <chrisf@ijw.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a couple places here where we should have called
mutex_unlock() before returning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Defaulting to 1, this gives a way to amplify the lux value before being
reduced by the programmed adc_bit shift.
Only support whole numbers right now. When this driver is converted to the new
IIO_CHAN framework, it will be easy to support the framework's pseudo float.
Add illuminance0_calibscale documentation to sysfs-bus-iio-light.
Signed-off-by: Bryan Freed <bfreed@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were some uninitialized variable warnings in iio. Two of
these came from the recent changes to how the private data was
allocated in 83f0422dc6 "staging:iio:accel:sca3000: allocate
state in iio_dev and use iio_priv to access."
drivers/staging/iio/accel/sca3000_core.c: In function 'sca3000_probe':
drivers/staging/iio/accel/sca3000_core.c:1137:9: warning: 'st' may be used uninitialized in this function
drivers/staging/iio/adc/ad7291.c: In function 'ad7291_probe':
drivers/staging/iio/adc/ad7291.c:805:15: warning: 'chip' may be used uninitialized in this function
drivers/staging/iio/dac/ad5624r_spi.c: In function 'ad5624r_probe':
drivers/staging/iio/dac/ad5624r_spi.c:228:24: warning: 'st' may be used uninitialized in this function
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ux500 machine was actually defining platform data for the
staging driver ste_rmi4, which is not OK. Let us instead define
some __weak platform data in the machine so that the staging
driver can override it at compile-time and we can thus have the
driver self-contained in staging.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new testmode command for retrieving rx reports from firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression problem in linux-next: post_reset and pre_reset are no longer
included in linux-next while they are in linux-3.0rc5.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: usbip-devel <usbip-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When unbinding a device on the host which was still attached on the
client, I got a NULL pointer dereference on the client. This turned out
to be due to kthread_stop() being called on an already dead kthread.
Here is how I was able to reproduce the problem:
server:# usbip bind -b 1-2
client:# usbip attach -h server -b 1-2
server:# usbip unbind -b 1-2
This patch fixes the problem by checking the kthread before attempting
to kill it, as it is done on the opposite side in
stub_shutdown_connection().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change package name to usbip-utils, email address to linux-usb, and
bump minor version number.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change messges to debug, and fix a few coding style issues.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Officially change stub_driver to usbip_host_driver. And, reorganize
usbip_host_driver.c while also cleaning up coding style.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
