Commit graph

277,199 commits

Author SHA1 Message Date
Mark Brown
556e4fb1d8 ASoC: Add stub baseband link on Speyside
Demonstrate the connection of a baseband to the system. We add a DAI for
the link to the baseband. This will become visible to the application
layer - audio should be started from the application layer using an
application such as this:

   http://opensource.wolfsonmicro.com/~gg/bluetooth-pcm/bluetooth_pcm.c

which starts up audio as for CPU based playback and record up to the point
where data is streamed.

Due to non-availability of baseband simulation hardware we reuse the
configuration for the CPU link with the CODEC acting as clock master,
allowing signals to be observed with a scope. A more standard system
would have separate configuration for the baseband with its own ops
structure and operations. Normally the baseband would be clock master
as the baseband audio will be synchronised to the external telephony
network.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:02:17 -07:00
Mark Brown
ea0e60de38 ASoC: Add pin switches for fixed analogue inputs and outputs on Speyside
Pin switches enable direct control of the DAPM state from userspace,
enabling simple enabling and disabling of the path. This is especially
useful for outputs such as the speaker which are composed of several
physical devices as it allows them to be controlled as a group.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:02:12 -07:00
Mark Brown
68688e78ed ASoC: Add Speyside headset jack detection support
Speyside makes use of support the WM8915 has for detecting the polarity
of the microphone and ground connections on headsets, using a GPIO to
control the polarity of the ground connection and switching between the
two microphone bias supplies available on the device in order to do so.
As a result of this the detection support is more involved than for most
other CODECs, using a callback to configure the current polarity of the
jack and translate this into the board-specific connections required for
the current scenario.

On Android some additional work is required to hook this up to the
application layer as the Android HeadsetObserver monitors a custom
drivers/switch API rather than the standard Linux APIs.  This can be
done by either updating HeadsetObserver or modifying the ALSA core to
report via drivers/switch as well.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:02:06 -07:00
Mark Brown
ea3e98e75a ASoC: Support the sub speaker driver on Speyside
Speyside includes a WM9081 configured as an external speaker driver taking
an analogue input from HPOUT2 on the WM8915 on the system. Add support for
this to the driver, using a prefix of "Sub" for the WM9081 controls to
ensure we avoid collisions with controls on the WM8915.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:02:01 -07:00
Mark Brown
ea0a591a28 ASoC: Optimise clock management for WM8915 Speyside
Dynamically enable and disable the FLL on the WM8915, configuring the
system clock to 256fs for 48kHz when the device is active but reverting
to using the input 32.768kHz clock directly at other times to support
features such as jack detection with minimal power consumption.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:01:57 -07:00
Mark Brown
ecfb1adf5f ASoC: Add basic widgets for WM8915 Speyside
Provide widgets for the basic widgets connected directly to the WM8915
on Speyside - the headphones, speaker, digital and analogue microphones.
For the outputs this is just documentation, for the inputs this ensures
that the relevant microphone biases are enabled when they are in use.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:01:52 -07:00
Mark Brown
9b8dc66fba ASoC: Initial audio support for Speyside on Cragganmore 6410
This is minimal code required to get audio out of the Speyside audio
subsystem on the Wolfson Cragganmore 6410 reference platform.  It sets
up the link between the CPU and AIF1 of the WM8915 on the system,
enabling audio playback via the headphone and speaker outputs of the
device (which require no further configuration except runtime).  It
allows verification of basic functionality of the system.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:01:30 -07:00
Mark Brown
9a841ebb9c ASoC: Create card DAPM widgets early so they can be used in callbacks
This helps with things like setting up the initial state.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 10:00:21 -07:00
Mark Brown
01b07e2d84 ASoC: Move WM8915 FLL operations onto the CODEC
Since the WM8915 FLL is not tied to a particular audio interface move it
to a CODEC wide operation.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-13 09:52:52 -07:00
Chris Wilson
5c72d064f7 drm/i915: Initialise g4x watermarks for disabled pipes
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.

Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
2011-04-13 09:28:41 -07:00
Linus Torvalds
85f2e689a5 Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
  x86 platform drivers: Build fix for intel_pmic_gpio
2011-04-13 09:15:55 -07:00
Linus Torvalds
66bbf58b55 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
  avr32: add ATAG_BOARDINFO
  don't check platform_get_irq's return value against zero
  avr32: init cannot ignore signals sent by force_sig_info()
  avr32: fix deadlock when reading clock list in debugfs
  avr32: Fix .size directive for cpu_enter_idle
  avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
  fix the wrong argument of the functions definition
2011-04-13 09:15:40 -07:00
Linus Torvalds
1f4f8eeaec Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
  Revert "i915: restore only the mode of this driver on lastclose"
  Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
  i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
  drm/radeon/kms: properly program vddci on evergreen+
  drm/radeon/kms: add voltage type to atom set voltage function
  drm/radeon/kms: fix pcie_p callbacks on btc and cayman
  drm/radeon/kms: fix suspend on rv530 asics
  drm/radeon/kms: clean up gart dummy page handling
  drm/radeon/kms: make radeon i2c put/get bytes less noisy
  drm/radeon/kms: pll tweaks for rv6xx
  drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
  radeon: Fix KMS CP writeback on big endian machines.
  i915: restore only the mode of this driver on lastclose
  drm/nvc0: improve vm flush function
  drm/nv50-nvc0: remove some code that doesn't belong here
  drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
  drm/nouveau: quirk for XFX GT-240X-YA
  drm/nv50-nvc0: work around an evo channel hang that some people see
  drm/nouveau: implement init table opcode 0x5c
  drm/nouveau: fix oops on unload with disabled LVDS panel
  ...
2011-04-13 09:10:25 -07:00
Matthew Garrett
21a8d026e0 x86 platform drivers: Build fix for intel_pmic_gpio
Fix an incorrect function name so the driver builds.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
2011-04-13 11:52:16 -04:00
Kevin Gan
9f72c1d977 Bluetooth: btmrvl: support Marvell Bluetooth device SD8787
The SD8787 firmware image is shared with mwifiex driver.
Whoever gets loaded first will be responsible for firmware
downloading.

Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Tristan Xu <xurf@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:05 -03:00
Gustavo F. Padovan
b86ed368f1 Bluetooth: Check return value of hci_recv_stream_fragment()
It may return error and in this case we do add to the stats.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:04 -03:00
Jiejing Zhang
78b4a56c28 Bluetooth: hci_uart: check the return value of recv()
Check the return value of hu->proto->recv() in hci_uart_tty_receive()
the recv() may return error, check it, not add this to statistics.

Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:03 -03:00
Szymon Janc
e1ba1f1546 Bluetooth: Fix Out Of Band pairing when mgmt interface is disabled
Use kernel stored remote Out Of Band data only if management interface
is enabled. Otherwise HCI_OP_REMOTE_OOB_DATA_NEG_REPLY was sent to
controller even if remote Out Of Band data was present in bluetoothd.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:02 -03:00
Gustavo F. Padovan
9f69bda6aa Bluetooth: Add proper handling of received LE data
Despite it works, handling through l2cap_data_channel() is wrongs.
That function should handle only connection oriented data.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:02 -03:00
Gustavo F. Padovan
0733119c0b Bluetooth: Clean up ath3k_load_firmware()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:01 -03:00
Gustavo F. Padovan
cd69a03af1 Bluetooth: Fix wrong comparison in listen()
We should check for the pi->scid there.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:20:00 -03:00
Gustavo F. Padovan
58d35f87ef Bluetooth: Move tx queue to struct l2cap_chan
tx_q is the queue used by ERTM mode.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:19:59 -03:00
Gustavo F. Padovan
c916fbe45c Bluetooth: Remove unneeded uninitialized_vars()
That was unnecessary use of it.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:19:58 -03:00
Gustavo F. Padovan
49208c9c7b Bluetooth: Remove some sk references from l2cap_core.c
Change some BT_DBG messages and consequently remove some struct sock
declarations.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:19:57 -03:00
Gustavo F. Padovan
39d5a3ee35 Bluetooth: Move SREJ list to struct l2cap_chan
As part of moving all the Channel related operation to struct l2cap_chan.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13 12:19:47 -03:00
Linus Torvalds
6631e635c6 block: don't flush plugged IO on forced preemtion scheduling
We really only want to unplug the pending IO when the process actually
goes to sleep.  So move the test for flushing the plug up to the place
where we actually deactivate the task - where we have properly checked
for preemption and for the process really sleeping.

Acked-by: Jens Axboe <jaxboe@fusionio.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-04-13 08:08:20 -07:00
Linus Torvalds
a626ca6a65 vm: fix vm_pgoff wrap in stack expansion
Commit 982134ba62 ("mm: avoid wrapping vm_pgoff in mremap()") fixed
the case of a expanding mapping causing vm_pgoff wrapping when you used
mremap.  But there was another case where we expand mappings hiding in
plain sight: the automatic stack expansion.

This fixes that case too.

This one also found by Robert Święcki, using his nasty system call
fuzzer tool.  Good job.

Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-04-13 08:07:28 -07:00
Andreas Bießmann
24a1a47562 avr32: add ATAG_BOARDINFO
The ATAG_BOARDINFO is intended to hand over the information
bd->bi_board_number from u-boot to the kernel.

This piece of information can be used to implement some kind of board
identification while booting the kernel. Therefore it is placed in .initdata
section and can be accessed via the new symbol board_number only while
initializing the kernel.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:59 +02:00
Uwe Kleine-König
c7d876321f don't check platform_get_irq's return value against zero
platform_get_irq returns -ENXIO on failure, so !int_irq was probably
always true.  Better use (int)int_irq <= 0.  Note that a return value of
zero is still handled as error even though this could mean irq0.

This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.

Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:57 +02:00
Matt Fleming
9f0d15aac9 avr32: init cannot ignore signals sent by force_sig_info()
We can delete the code that checks to see if we're sending an ignored
signal to init because force_sig_info() already handles this case.
force_sig_info() will kill init even if the signal handler is SIG_DFL
and the scenario described in the comment where init might "generate
the same exception over and over again" cannot occur (force_sig_info()
clears SIGNAL_UNKILLABLE to ensure that init will die).

Also, the use of is_global_init() is not correct in the multhreaded
case, as Oleg Nesterov explains,

	"is_global_init() is not right in theory, /sbin/init can be
	multithreaded. And, this doesn't cover the sub-namespace
	inits... I'd suggest to check SIGNAL_UNKILLABLE, but looking
	closer I think you can simply remove this code."

It seems this code was copied from arch/powerpc in March 2007 in commit

  623b0355d5 "[AVR32] Clean up exception handling code"

but the code was deleted from arch/powerpc in November 2009 in commit

  a0592d42fe "powerpc: kill the obsolete code under is_global_init()"

So catch up with powerpc and delete the bogus code.

Signed-off-by: Matt Fleming <matt.fleming@linux.intel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:55 +02:00
Ole Henrik Jahren
6e2ad51190 avr32: fix deadlock when reading clock list in debugfs
When writing out /sys/kernel/debug/at32ap_clk, clock list lock is being
held while clk_get() is called. clk_get() attempts to take the same
lock, which results in deadlock. Introduce and call lock free version,
__clk_get(), instead.

Signed-off-by: Ole Henrik Jahren <olehenja@alumni.ntnu.no>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:52 +02:00
Ben Hutchings
51ef85d8f9 avr32: Fix .size directive for cpu_enter_idle
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does.  In binutils 2.21 these are treated
as errors.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:49 +02:00
Jean-Christophe PLAGNIOL-VILLARD
024b3f2936 avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
introduce in commit d75f1bfdbc

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:45 +02:00
Wanlong Gao
8faf9e3838 fix the wrong argument of the functions definition
The functions of eic_chip's memebers use the wrong argument .

Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-04-13 15:46:37 +02:00
Laurent Pinchart
8eca7a004e [media] omap3isp: resizer: Center the crop rectangle
When the crop rectangle needs to be modified to match hardware
requirements, center the resulting rectangle on the requested rectangle
instead of removing pixels from the right and bottom sides only.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 10:33:58 -03:00
Laurent Pinchart
21d2b9587f [media] media: Use correct ioctl name in MEDIA_IOC_SETUP_LINK documentation
The documentation incorrectly refers to MEDIA_IOC_ENUM_LINKS, fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 10:30:12 -03:00
Uwe Kleine-König
122af36601 [media] V4L: mx3_camera: select VIDEOBUF2_DMA_CONTIG instead of VIDEOBUF_DMA_CONTIG
Since commit

	379fa5d ([media] V4L: mx3_camera: convert to videobuf2)

mx3_camera uses videobuf2, but that commit didn't upgrade the select
resulting in the following build failure:

	drivers/built-in.o: In function `mx3_camera_init_videobuf':
	clkdev.c:(.text+0x86580): undefined reference to `vb2_dma_contig_memops'
	drivers/built-in.o: In function `mx3_camera_probe':
	clkdev.c:(.devinit.text+0x3548): undefined reference to `vb2_dma_contig_init_ctx'
	clkdev.c:(.devinit.text+0x3578): undefined reference to `vb2_dma_contig_cleanup_ctx'
	drivers/built-in.o: In function `mx3_camera_remove':
	clkdev.c:(.devexit.text+0x674): undefined reference to `vb2_dma_contig_cleanup_ctx'
	make[2]: *** [.tmp_vmlinux1] Error 1
	make[1]: *** [sub-make] Error 2
	make: *** [all] Error 2

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:56:54 -03:00
Guennadi Liakhovetski
d16290d77a [media] V4L: sh_mobile_ceu_camera: fix typos in documentation
Fix a couple of typos and clarify a formula in sh_mobile_ceu driver
documentation.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:56:37 -03:00
Guennadi Liakhovetski
cb743930eb [media] sh_mobile_csi2: fix module reloading
If the camera host driver (sh_mobile_ceu_camera.c) is unloaded and then
reloaded, probe will fail, because camera client .set_bus_param() and
.query_bus_param() methods have been set to NULL. Fix this by caching
the original pointers and restoring them on driver-unbind.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:55:38 -03:00
Guennadi Liakhovetski
c8dd707805 [media] soc-camera: don't dereference I2C client after it has been removed
i2c_unregister_device() frees the I2C client, so, dereferencing it
afterwards is a bug, that leads to Oopses.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:55:06 -03:00
Guennadi Liakhovetski
3e31f2b945 [media] imx074: return a meaningful error code instead of -1
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:54:35 -03:00
Guennadi Liakhovetski
24105ebc05 [media] soc-camera: fix a recent multi-camera breakage on sh-mobile
With the introduction of CSI2 support on sh-mobile, the host driver
switched to using v4l2_device_call_until_err() with grp_id == 0 to
call subdev operations on the sensor and the CSI2 subdev. However,
this has broken multi-client set ups like the one on migor, because
that way all operations get called on both clients. To fix this add
a grp_id and set it to the client private context.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:54:16 -03:00
Guennadi Liakhovetski
c6c7354412 [media] v4l2-device: fix a macro definition
v4l2_device_unregister_subdev() wrongly uses "arg..." instead of "## arg"
in its body. Fix it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:53:29 -03:00
Guennadi Liakhovetski
99a41771bf [media] videobuf2: fix an error message
buf->size is not yet initialised in videobuf2-dma-contig at the time of
the error message, use "size."

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:52:36 -03:00
Guennadi Liakhovetski
62a79436a5 [media] videobuf2: fix core to correctly identify allocation failures
The videobuf2-dma-contig allocator returns an ERR_PTR() on failure, not
a NULL like all other allocators. Fix videobuf2-core to also correctly
recognise those failures.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:52:16 -03:00
John W. Linville
8962d87129 ath5k: improve comments for optimized tx descriptor setup
Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-13 08:49:10 -04:00
Andy Walls
0f890ab1b5 [media] cx18: Fix list BUG for IDX stream, triggerable in cx18_probe() error clean up,
If allocating stream buffers for one of the primary streams (e.g. YUV)
failed during card probe, the error path clean up would try to manipulate
the yet unitialized IDX stream structures.  This caused a BUG due to
unitialized list heads.

Detect that case and ignore the uninitialized IDX stream.

Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-04-13 09:41:02 -03:00
Jozsef Kadlecsik
91eb7c08c6 netfilter: ipset: SCTP, UDPLITE support added
SCTP and UDPLITE port support added to the hash:*port* set types.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
2011-04-13 13:51:38 +02:00
Jozsef Kadlecsik
eafbd3fde6 netfilter: ipset: set match and SET target fixes
The SET target with --del-set did not work due to using wrongly
the internal dimension of --add-set instead of --del-set.
Also, the checkentries did not release the set references when
returned an error. Bugs reported by Lennert Buytenhek.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
2011-04-13 13:45:57 +02:00
Jozsef Kadlecsik
0e8a835aa5 netfilter: ipset: bitmap:ip,mac type requires "src" for MAC
Enforce that the second "src/dst" parameter of the set match and SET target
must be "src", because we have access to the source MAC only in the packet.
The previous behaviour, that the type required the second parameter
but actually ignored the value was counter-intuitive and confusing.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
2011-04-13 13:43:23 +02:00