Commit graph

277,199 commits

Author SHA1 Message Date
Vivek Natarajan
23952ec928 ath9k_hw: Increase the wait count for nf load.
Increasing the wait count makes the nf load pass in
most of the cases.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:36 -05:00
Vivek Natarajan
75e0351245 ath9k_hw: Fix PLL initialization for AR9485.
Increase the delay to make sure the initialization of pll
passes.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:36 -05:00
Vivek Natarajan
7ea1362c5d ath9k_hw: Improve idle power consumption for AR9485.
Set some GPIO pins to Pull-down mode to save power.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:36 -05:00
Felix Fietkau
2e286947f1 ath9k: remove support for the FIF_PROMISC_IN_BSS filter flag
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:

ath: Could not stop RX, we could be confusing the DMA engine when we start RX up

Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.

This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:36 -05:00
Grazvydas Ignotas
5f6722ee63 wl1251: fix elp_work race condition
While working on PS I've noticed elp_work is kicking rather often, and
sometimes the chip is put to sleep before 5ms delay expires. This
seems to happen because by the time wl1251_ps_elp_wakeup is called
elp_work might still be pending. After wakeup is done, the processing
may take some time, during which 5ms might expire and elp_work might
get scheduled. In this case, ss soon as 1st thread finishes work and
releases the mutex, elp_work will then put the device to sleep without
5ms delay. In addition 1st thread will queue additional elp_work
needlessly.

Fix this by cancelling work in wl1251_ps_elp_wakeup instead.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:35 -05:00
Grazvydas Ignotas
d0c331aff9 wl1251: remove wl1251_ps_set_elp function
wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip
from/to ELP, however all callers of wl1251_ps_set_mode() have already
taken the chip out of ELP and puts it back to ELP when they finish.
This makes ELP calls (and register writes they result in) superfluous.

So remove wl1251_ps_set_elp function and call acx_sleep_auth directly.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:35 -05:00
Tao Ma
eba2ed9c96 block: remove obsolete comments for blkdev_issue_zeroout.
barrier is already removed, so remove the obsolete comments
in blkdev_issue_zeroout.

Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-11 20:13:54 +01:00
Tao Ma
805f6b5e1c blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
In blk_add_trace_rq, we only chose the minor 2 bits from
request's cmd_flags and did some check for discard.
so most of other flags(e.g, REQ_SYNC) are missing.

For example, with a sync write after blkparse we get:
  8,16   1        1     0.001776503  7509  A  WS 1349632 + 1024 <- (8,17) 1347584
  8,16   1        2     0.001776813  7509  Q  WS 1349632 + 1024 [dd]
  8,16   1        3     0.001780395  7509  G  WS 1349632 + 1024 [dd]
  8,16   1        5     0.001783186  7509  I   W 1349632 + 1024 [dd]
  8,16   1       11     0.001816987  7509  D   W 1349632 + 1024 [dd]
  8,16   0        2     0.006218192     0  C   W 1349632 + 1024 [0]

Since now we have integrated the flags of both bio and request,
it is safe to pass rq->cmd_flags directly to __blk_add_trace.

With this patch, after a sync write we get:
  8,16   1        1     0.001776900  5425  A  WS 1189888 + 1024 <- (8,17) 1187840
  8,16   1        2     0.001777179  5425  Q  WS 1189888 + 1024 [dd]
  8,16   1        3     0.001780797  5425  G  WS 1189888 + 1024 [dd]
  8,16   1        5     0.001783402  5425  I  WS 1189888 + 1024 [dd]
  8,16   1       11     0.001817468  5425  D  WS 1189888 + 1024 [dd]
  8,16   0        2     0.005640709     0  C  WS 1189888 + 1024 [0]

Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-11 20:11:59 +01:00
John W. Linville
409ec36c32 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem 2011-03-11 14:11:11 -05:00
Stephen M. Cameron
978eb516a4 cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
This bit got lost somewhere along the way.  Without this, panic.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-11 20:07:38 +01:00
Stephen M. Cameron
957c2ec558 cciss: export resettable host attribute
This attribute, requested by Redhat, allows kexec-tools to know
whether the controller can honor the reset_devices kernel parameter
and actually reset the controller.  For kdump to work properly it
is necessary that the reset_devices parameter be honored.  This
attribute enables kexec-tools to warn the user if they attempt to
designate a non-resettable controller as the dump device.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-11 20:06:09 +01:00
Subhasish Ghosh
9a9fb12a48 davinci: macro rename DA8XX_LPSC0_DMAX to DA8XX_LPSC0_PRUSS.
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.

Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Sergei Shtylyov
b688c2fba5 davinci: DA850 EVM: kill useless variable
Commit 75e2ea643f (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Sekhar Nori
16a3c8320a davinci: add spi devices support for da830/omap-l137/am17x evm
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.

Based on SPI flash device support for MityDSP-L138F platform.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Sekhar Nori
fdce556806 davinci: add spi devices support for da850/omap-l138/am18x evm
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.

Based on SPI flash device support for MityDSP-L138F platform.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Michael Williamson
dd561c6a77 davinci: add spi devices support for MityDSP-L138/MityARM-1808 platform
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Michael Williamson
54ce6883d2 davinci: da8xx: add spi resources and registration routine
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:29 -08:00
Michael Williamson
12d35cf374 davinci: da850: add spi device clock definitions
Add spi clock information for da850.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:28 -08:00
Michael Williamson
4918b40dc8 davinci: da830: fix driver name for spi clocks
The spi driver name called out for the da830 spi clock list is not correct,
fix it.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:28 -08:00
Michael Williamson
e38c2b2226 davinci: da8xx: clean up magic numbers in devices-da8xx.c
Extract magic numbers from DMA resource initializers to #defines.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:28 -08:00
Michael Williamson
e647198069 davinci: remove unused DA830_edma_ch enum
The DA830_edma_ch enum set is not used.  Remove it.

Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 10:48:28 -08:00
Ike Panhc
883ae7992c ideapad: read brightness setting on brightness key notify
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=25922

On ideapad Y530, the brightness key notify will be blocked if the last notify
is not responsed by getting the brightness value. Read value when we get the
notify shall fix the problem and will not have any difference on other ideapads.

Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
2011-03-11 12:52:22 -05:00
Ivan Djelic
fc2ff592b5 mtd: nand: enable software BCH ECC in nand simulator
This patch adds option 'bch' to nandsim, which can be used to enable
software BCH ECC (introduced in previous patches) and select BCH error
correction capability.

Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-11 17:49:31 +00:00
Ivan Djelic
193bd40026 mtd: nand: add software BCH ECC support
This patch adds software BCH ECC support to mtd, in order to handle recent
NAND device ecc requirements (4 bits or more).

It does so by adding a new ecc mode (NAND_ECC_SOFT_BCH) for use by board
drivers, and a new Kconfig option to enable BCH support. It relies on the
generic BCH library introduced in a previous patch.

When a board driver uses mode NAND_ECC_SOFT_BCH, it should also set fields
chip->ecc.size and chip->ecc.bytes to select BCH ecc data size and required
error correction capability. See nand_bch_init() documentation for details.

It has been tested on the following platforms using mtd-utils, UBI and
UBIFS: x86 (with nandsim), arm926ejs.

Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-11 17:49:08 +00:00
Tony Lindgren
0d9596958d Merge branch 'for_2.6.39/pm-integration' of ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus 2011-03-11 09:39:58 -08:00
Tony Lindgren
a2358a7bc3 Merge branch 'integration-2.6.39-for-tony' of git://git.pwsan.com/linux-integration into omap-for-linus
Conflicts:
	arch/arm/mach-omap2/pm34xx.c
2011-03-11 09:20:03 -08:00
Arnaldo Carvalho de Melo
171b3be9c4 perf symbol: Move sym_entry->skip to symbol->ignore
While going thru each of the sym_entry fields looking to reduce it to
the set of entries needed when in an active symbols list, 'skip' should
really be in symbol, as we set it when loading the symtab.

And the space used by the basic symbol allocation remains the same as
we had 5 bytes of padding.

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-03-11 13:36:01 -03:00
Arnaldo Carvalho de Melo
878b439dcc perf symbols: Rename dso->origin to dso->symtab_type
And the DSO__ORIG_ enum to SYMTAB__, to clarify that this is about from
where the symtab was obtained.

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-03-11 13:28:45 -03:00
Arnaldo Carvalho de Melo
8b8ba4a9a5 perf top: Remove redundant syme->origin field
We can get it from syme->map->dso->kernel (that should be renamed to
origin, but leave this for another patch).

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-03-11 13:28:45 -03:00
Arnaldo Carvalho de Melo
ec52d9765a perf top: Remove redundant perf_top->sym_counter
We can get that counter index from perf_top->sym_evsel->idx instead.

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2011-03-11 13:28:45 -03:00
Pekka Enberg
865d794d1f Merge branch 'slab/urgent' into slab/next 2011-03-11 18:11:19 +02:00
Pekka Enberg
c914955675 Merge branch 'slab/rcu' into slab/next
Conflicts:
	mm/slub.c
2011-03-11 18:10:45 +02:00
Lai Jiangshan
5bfe53a77e slab,rcu: don't assume the size of struct rcu_head
The size of struct rcu_head may be changed. When it becomes larger,
it may pollute the data after struct slab.

Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 18:06:35 +02:00
Lai Jiangshan
da9a638c6f slub,rcu: don't assume the size of struct rcu_head
The size of struct rcu_head may be changed. When it becomes larger,
it will pollute the page array.

We reserve some some bytes for struct rcu_head when a slab
is allocated in this situation.

Changed from V1:
	use VM_BUG_ON instead BUG_ON

Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 18:06:34 +02:00
Lai Jiangshan
ab9a0f196f slub: automatically reserve bytes at the end of slab
There is no "struct" for slub's slab, it shares with struct page.
But struct page is very small, it is insufficient when we need
to add some metadata for slab.

So we add a field "reserved" to struct kmem_cache, when a slab
is allocated, kmem_cache->reserved bytes are automatically reserved
at the end of the slab for slab's metadata.

Changed from v1:
	Export the reserved field via sysfs

Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 18:06:34 +02:00
Konrad Rzeszutek Wilk
86b32122fd xen/e820: Don't mark balloon memory as E820_UNUSABLE when running as guest and fix overflow.
If we have a guest that asked for:

memory=1024
maxmem=2048

Which means we want 1GB now, and create pagetables so that we can expand
up to 2GB, we would have this E820 layout:

[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 00000000000a0000 (usable)
[    0.000000]  Xen: 00000000000a0000 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 0000000080800000 (usable)

Due to patch: "xen/setup: Inhibit resource API from using System RAM E820 gaps as PCI mem gaps."
we would mark the memory past the 1GB mark as unusuable resulting in:

[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 00000000000a0000 (usable)
[    0.000000]  Xen: 00000000000a0000 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 0000000040000000 (usable)
[    0.000000]  Xen: 0000000040000000 - 0000000080800000 (unusable)

which meant that we could not balloon up anymore. We could
balloon the guest down. The fix is to run the code introduced
by the above mentioned patch only for the initial domain.

We will have to revisit this once we start introducing a modified
E820 for PCI passthrough so that we can utilize the P2M identity code.

We also fix an overflow by having UL instead of ULL on 32-bit machines.

[v2: Ian pointed to the overflow issue]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2011-03-11 11:01:45 -05:00
Christoph Lameter
8a5ec0ba42 Lockless (and preemptless) fastpaths for slub
Use the this_cpu_cmpxchg_double functionality to implement a lockless
allocation algorithm on arches that support fast this_cpu_ops.

Each of the per cpu pointers is paired with a transaction id that ensures
that updates of the per cpu information can only occur in sequence on
a certain cpu.

A transaction id is a "long" integer that is comprised of an event number
and the cpu number. The event number is incremented for every change to the
per cpu state. This means that the cmpxchg instruction can verify for an
update that nothing interfered and that we are updating the percpu structure
for the processor where we picked up the information and that we are also
currently on that processor when we update the information.

This results in a significant decrease of the overhead in the fastpaths. It
also makes it easy to adopt the fast path for realtime kernels since this
is lockless and does not require the use of the current per cpu area
over the critical section. It is only important that the per cpu area is
current at the beginning of the critical section and at the end.

So there is no need even to disable preemption.

Test results show that the fastpath cycle count is reduced by up to ~ 40%
(alloc/free test goes from ~140 cycles down to ~80). The slowpath for kfree
adds a few cycles.

Sadly this does nothing for the slowpath which is where the main issues with
performance in slub are but the best case performance rises significantly.
(For that see the more complex slub patches that require cmpxchg_double)

Kmalloc: alloc/free test

Before:

10000 times kmalloc(8)/kfree -> 134 cycles
10000 times kmalloc(16)/kfree -> 152 cycles
10000 times kmalloc(32)/kfree -> 144 cycles
10000 times kmalloc(64)/kfree -> 142 cycles
10000 times kmalloc(128)/kfree -> 142 cycles
10000 times kmalloc(256)/kfree -> 132 cycles
10000 times kmalloc(512)/kfree -> 132 cycles
10000 times kmalloc(1024)/kfree -> 135 cycles
10000 times kmalloc(2048)/kfree -> 135 cycles
10000 times kmalloc(4096)/kfree -> 135 cycles
10000 times kmalloc(8192)/kfree -> 144 cycles
10000 times kmalloc(16384)/kfree -> 754 cycles

After:

10000 times kmalloc(8)/kfree -> 78 cycles
10000 times kmalloc(16)/kfree -> 78 cycles
10000 times kmalloc(32)/kfree -> 82 cycles
10000 times kmalloc(64)/kfree -> 88 cycles
10000 times kmalloc(128)/kfree -> 79 cycles
10000 times kmalloc(256)/kfree -> 79 cycles
10000 times kmalloc(512)/kfree -> 85 cycles
10000 times kmalloc(1024)/kfree -> 82 cycles
10000 times kmalloc(2048)/kfree -> 82 cycles
10000 times kmalloc(4096)/kfree -> 85 cycles
10000 times kmalloc(8192)/kfree -> 82 cycles
10000 times kmalloc(16384)/kfree -> 706 cycles

Kmalloc: Repeatedly allocate then free test

Before:

10000 times kmalloc(8) -> 211 cycles kfree -> 113 cycles
10000 times kmalloc(16) -> 174 cycles kfree -> 115 cycles
10000 times kmalloc(32) -> 235 cycles kfree -> 129 cycles
10000 times kmalloc(64) -> 222 cycles kfree -> 120 cycles
10000 times kmalloc(128) -> 343 cycles kfree -> 139 cycles
10000 times kmalloc(256) -> 827 cycles kfree -> 147 cycles
10000 times kmalloc(512) -> 1048 cycles kfree -> 272 cycles
10000 times kmalloc(1024) -> 2043 cycles kfree -> 528 cycles
10000 times kmalloc(2048) -> 4002 cycles kfree -> 571 cycles
10000 times kmalloc(4096) -> 7740 cycles kfree -> 628 cycles
10000 times kmalloc(8192) -> 8062 cycles kfree -> 850 cycles
10000 times kmalloc(16384) -> 8895 cycles kfree -> 1249 cycles

After:

10000 times kmalloc(8) -> 190 cycles kfree -> 129 cycles
10000 times kmalloc(16) -> 76 cycles kfree -> 123 cycles
10000 times kmalloc(32) -> 126 cycles kfree -> 124 cycles
10000 times kmalloc(64) -> 181 cycles kfree -> 128 cycles
10000 times kmalloc(128) -> 310 cycles kfree -> 140 cycles
10000 times kmalloc(256) -> 809 cycles kfree -> 165 cycles
10000 times kmalloc(512) -> 1005 cycles kfree -> 269 cycles
10000 times kmalloc(1024) -> 1999 cycles kfree -> 527 cycles
10000 times kmalloc(2048) -> 3967 cycles kfree -> 570 cycles
10000 times kmalloc(4096) -> 7658 cycles kfree -> 637 cycles
10000 times kmalloc(8192) -> 8111 cycles kfree -> 859 cycles
10000 times kmalloc(16384) -> 8791 cycles kfree -> 1173 cycles

Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 17:42:49 +02:00
Christoph Lameter
d3f661d69a slub: Get rid of slab_free_hook_irq()
The following patch will make the fastpaths lockless and will no longer
require interrupts to be disabled. Calling the free hook with irq disabled
will no longer be possible.

Move the slab_free_hook_irq() logic into slab_free_hook. Only disable
interrupts if the features are selected that require callbacks with
interrupts off and reenable after calls have been made.

Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 17:42:49 +02:00
Christoph Lameter
1a757fe5d4 slub: min_partial needs to be in first cacheline
It is used in unfreeze_slab() which is a performance critical
function.

Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
2011-03-11 17:42:49 +02:00
Pekka Enberg
2a6c5176ec Merge branch 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu into slub/lockless 2011-03-11 17:42:05 +02:00
Jean Pihet
5e7c58dc8d perf: add OMAP support for the new power events
The patch adds the new power management trace points for
the OMAP architecture.

The trace points are for:
- default idle handler. Since the cpuidle framework is
  instrumented in the generic way there is no need to
  add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
  the actually hit state.

Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.

Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.

Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 07:21:44 -08:00
Shweta Gulati
a271e58cfb OMAP4: Add IVA OPP enteries.
This Patch adds OPP enteries for IVA  in OMAP4 OPP Table

Tested on OMAP4430 SDP Board.

Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 07:21:44 -08:00
Shweta Gulati
d9a2012d32 OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
Update MPU, IVA and CORE voltage Rail values obtained from
OMAP4430 Data Manual Operating Condition Addendum_v0.4.

Tested on OMAP4430 SDP Board.

Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 07:21:44 -08:00
Shweta Gulati
273032f782 OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.

Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 07:21:44 -08:00
Vishwanath BS
15f13e23e8 OMAP3+: OPP: Replace voltage values with Macros
Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.

This will avoid opp table and voltage layer having conflicting values.

Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11 07:21:44 -08:00
David Woodhouse
89d8d32060 mtd: fix printf format warnings, mostly lack of %zd for size_t, in mtdswap
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-11 15:17:41 +00:00
Takashi Iwai
7e79443ce2 ALSA: atiixp - Fix wrong time-out checks during ac-link reset
The time-out in snd_atiixp_aclink_reset() is wrongly checked, and
it resulted in exiting from the loop at the first iteration.

Reported-by: Amir Shamsuddin <AmirS2+alsa@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-03-11 15:45:32 +01:00
Lukas Czerner
0aeea18964 block: fix mis-synchronisation in blkdev_issue_zeroout()
BZ29402
https://bugzilla.kernel.org/show_bug.cgi?id=29402

We can hit serious mis-synchronization in bio completion path of
blkdev_issue_zeroout() leading to a panic.

The problem is that when we are going to wait_for_completion() in
blkdev_issue_zeroout() we check if the bb.done equals issued (number of
submitted bios). If it does, we can skip the wait_for_completition()
and just out of the function since there is nothing to wait for.
However, there is a ordering problem because bio_batch_end_io() is
calling atomic_inc(&bb->done) before complete(), hence it might seem to
blkdev_issue_zeroout() that all bios has been completed and exit. At
this point when bio_batch_end_io() is going to call complete(bb->wait),
bb and wait does not longer exist since it was allocated on stack in
blkdev_issue_zeroout() ==> panic!

(thread 1)                      (thread 2)
bio_batch_end_io()              blkdev_issue_zeroout()
  if(bb) {                      ...
    if (bb->end_io)             ...
      bb->end_io(bio, err);     ...
    atomic_inc(&bb->done);      ...
    ...                         while (issued != atomic_read(&bb.done))
    ...                         (let issued == bb.done)
    ...                         (do the rest of the function)
    ...                         return ret;
    complete(bb->wait);
    ^^^^^^^^
    panic

We can fix this easily by simplifying bio_batch and completion counting.

Also remove bio_end_io_t *end_io since it is not used.

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reported-by: Eric Whitney <eric.whitney@hp.com>
Tested-by: Eric Whitney <eric.whitney@hp.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
CC: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-03-11 15:36:08 +01:00
Xiaochen Wang
629286b956 mtd: sm_rtl: check kmalloc return value
Because malloc/kzalloc may fail, we should check kmalloc/kzalloc return value
 in sm_create_sysfs_attributes(), mtd/sm_rtl.c and do error handling.
Meanwhile, we should check sm_create_sysfs_attributes return value.

Signed-off-by: Xiaochen Wang <wangxiaochen0@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-11 14:27:10 +00:00
Steffen Sledz
1065cda8a1 mtd: cfi: add support for AMIC flashes (e.g. A29L160AT)
Signed-off-by: Steffen Sledz <sledz@dresearch.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-03-11 14:27:01 +00:00