xHCI 4.8.3 recommends that software should simply assume endpoints to
halt after certain events, without looking at the Endpoint Context for
confirmation, because HCs may be slow to update that.
While no cases of such "slowness" appear to be known, different problem
exists on AMD Promontory chipsets: they may halt and generate a transfer
event, but fail to ever update the Endpoint Context at all, at least not
until some command is queued and fails with Context State Error. This is
easily triggered by disconnecting D- of a full speed serial device.
Possibly similar bug in non-AMD hardware has been reported to linux-usb.
In such case, failed TD is given back without erasing from the ring and
endpoint isn't reset. If some URB is unlinked later, Stop Endpoint fails
and its handler resets the endpoint. On next submission it will restart
on the stale TD. Outcome is UAF on success, or another halt on error and
then Dequeue doesn't move and URBs are stuck. Unlinking and resubmitting
the URBs causes unlimited ring expansion if the situation repeats.
This can be solved by ignoring Endpoint Context State and trusting that
endpoints halt when required, except one known case in ancient hardware.
The check for "Already resolving halted ep" becomes redundant, because
for these completion codes we now jump to xhci_handle_halted_endpoint()
which deals with pending EP_HALTED internally.
Link: https://lore.kernel.org/linux-usb/20250311234139.0e73e138@foxbook/
Link: https://lore.kernel.org/linux-usb/20250918055527.4157212-1-zhangjinpeng@kylinos.cn/
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, each port's 'addr' field pointed to the base of the Host
Controller USB Port Register Set, and specific registers were accessed
using macros such as (port->addr + PORTPMSC).
This patch replaces the raw '__le32 __iomem *addr' pointer with a typed
'struct xhci_port_regs __iomem *port_reg' pointer. With this change,
individual registers can be accessed directly through the structure
fields:
Before:
port->addr
port->addr + PORTPMSC
port->addr + PORTLI
port->addr + PORTHLPMC
After:
port->port_reg->portsc
port->port_reg->portpmsc
port->port_reg->portli
port->port_reg->porthlpmc
This improves code readability and makes register access more intuitive
by using named struct members instead of pointer arithmetic and macros.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new struct for the Host Controller USB Port Register Set to
enhance readability and maintainability.
The Host Controller Operational Registers (struct 'xhci_op_regs') span from
offset 0x0 to 0x3FF and consist of fixed fields. Following these fixed
fields are the Host Controller USB Port Register Sets, which are dynamic
and repeat from 1 to MaxPorts, as defined by HCSPARAMS1.
Currently, the struct 'xhci_op_regs' includes:
__le32 port_status_base; The first PORTSC
__le32 port_power_base; The first PORTPMSC
__le32 port_link_base; The first PORTLI
__le32 reserved5; The first PORTHLPMC, not reserved
__le32 reserved6[NUM_PORT_REGS*254]; Port registers 2 to MaxPorts
Replace this with the simpler:
struct xhci_port_regs port_regs[]; Port registers 1 to MaxPorts
Host Controller USB Port Register Set:
| Offset | Mnemonic | Register Name
--------------------------------------------------------------------------
| 0x0 | PORTSC | Port Status and Control
| 0x4 | PORTPMSC | Port Power Management Status and Control
| 0x8 | PORTLI | Port Link Info
| 0xC | PORTHLPMC | Port Hardware LPM Control
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a dedicated helper function to read the USB Port Status and Control
(PORTSC) register. This complements xhci_portsc_writel() and improves code
clarity by providing a clear counterpart for reading the register.
Suggested-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Peter Chen <peter.chen@kerne.org>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a dedicated write function for the USB Port Register Set (PORTSC)
that includes tracing capabilities for values written to the PORTSC
register. This enhancement minimizes code duplication and improves
debugging.
The PORTSC register is part of the Host Controller USB Port Register Set,
comprising 4 x 32-bit registers. As the first register, PORTSC is accessed
directly via 'port->addr'. Future commits will introduce a dedicated Port
register struct to further streamline access.
By adding the xhci_portsc_writel() function prior to these changes, we
significantly reduce the number of same line modifications required.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework xhci_decode_portsc(), which is used for PORTSC tracing, to make
the output more compact and general.
The function now first prints the multi-bit fields (port speed and link
state), followed by the abbreviated names of each individual bit as
defined in the xHCI specification. This reduces message length and makes
the output easier to read.
This change prepares for upcoming patches that will trace all PORTSC
writes, requiring the same decoding logic to handle both reads and writes.
This is particularly important for Read-Write-1-to-Clear (RW1C) bits,
where the semantics differ between read and write operations. For
example, when reading the Port Enabled bit, a set bit means the port is
enabled; when writing, a set bit indicates the port is being disabled.
The decoder now also includes the following fields:
Port Link State Write Strobe (LWS)
Device Removable (DR)
Warm Port Reset (WPR)
==== Examples Traces ====
Before:
0x00201201 Powered Connected Disabled Link:U0 PortSpeed:4 Change: PRC Wake:
0x0a0002a0 Powered Not-connected Disabled Link:RxDetect PortSpeed:0 \
Change: Wake: WCE WOE
After:
0x00201201 Speed=4 Link=U0 CCS PP PRC
0x0a0002a0 Speed=0 Link=RxDetect PP WCE WOE
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trb_in_td() checking is quite complex, especially when checking for
TRBs in ranges that can span several segments.
Simplify the search by creating a position index for each TRB on the
ring, and just compare the position indexes.
Add a more generic dma_in_range() helper that checks if a trb dma
address is in the range between a start and end trb and call it from
trb_in_td()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_dma_to_trb() helper, and use it to find the transfer TRB
early in handle_tx_event() based on the dma address found in the
event TRB.
With this helper we can avoid using 'ep_seg' transfer TRB segment
variable as both a a boolean to indicate if the transfer TRB is part
of the next queued TD, and to actually find the transfer TRB based
on ep_seg and ep_trb_dma.
This is a first step in reworking and cleaning up trb_in_td() and
handle_tx_event()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20251119142417.2820519-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the kernel-doc notation in xhck-mtk.h to avoid most kernel-doc
warnings. Summary of changes:
- don't use /** to begin comments that are not in kernel-doc format
- add missing "struct mu3h_sch_tt" kernel-doc line
- convert several "struct mu3h_...:" to using " - " to separate the
struct name from its short description
- add a missing @speed: struct member description
Warning messages that are fixed:
xhci-mtk.h:25: warning: This comment starts with '/**', but isn't a
kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* To simplify scheduler algorithm, set a upper limit for ESIT,
xhci-mtk.h:25: warning: missing initial short description on line:
* To simplify scheduler algorithm, set a upper limit for ESIT,
Warning: drivers/usb/host/xhci-mtk.h:36 Cannot find identifier on line:
* @fs_bus_bw_out: save bandwidth used by FS/LS OUT eps in each uframes
Warning: drivers/usb/host/xhci-mtk.h:37 Cannot find identifier on line:
* @fs_bus_bw_in: save bandwidth used by FS/LS IN eps in each uframes
Warning: drivers/usb/host/xhci-mtk.h:38 Cannot find identifier on line:
* @ls_bus_bw: save bandwidth used by LS eps in each uframes
Warning: drivers/usb/host/xhci-mtk.h:39 Cannot find identifier on line:
* @fs_frame_bw: save bandwidth used by FS/LS eps in each FS frames
Warning: drivers/usb/host/xhci-mtk.h:40 Cannot find identifier on line:
* @in_ss_cnt: the count of Start-Split for IN eps
Warning: drivers/usb/host/xhci-mtk.h:41 Cannot find identifier on line:
* @ep_list: Endpoints using this TT
Warning: drivers/usb/host/xhci-mtk.h:42 Cannot find identifier on line:
*/
Warning: drivers/usb/host/xhci-mtk.h:43 Cannot find identifier on line:
struct mu3h_sch_tt {
Warning: drivers/usb/host/xhci-mtk.h:44 Cannot find identifier on line:
u16 fs_bus_bw_out[XHCI_MTK_MAX_ESIT];
Warning: drivers/usb/host/xhci-mtk.h:45 Cannot find identifier on line:
u16 fs_bus_bw_in[XHCI_MTK_MAX_ESIT];
Warning: drivers/usb/host/xhci-mtk.h:46 Cannot find identifier on line:
u8 ls_bus_bw[XHCI_MTK_MAX_ESIT];
Warning: drivers/usb/host/xhci-mtk.h:47 Cannot find identifier on line:
u16 fs_frame_bw[XHCI_MTK_FRAMES_CNT];
Warning: drivers/usb/host/xhci-mtk.h:48 Cannot find identifier on line:
u8 in_ss_cnt[XHCI_MTK_MAX_ESIT];
Warning: drivers/usb/host/xhci-mtk.h:49 Cannot find identifier on line:
struct list_head ep_list;
Warning: drivers/usb/host/xhci-mtk.h:50 Cannot find identifier on line:
};
Warning: drivers/usb/host/xhci-mtk.h:51 Cannot find identifier on line:
Warning: drivers/usb/host/xhci-mtk.h:52 Cannot find identifier on line:
/**
Warning: drivers/usb/host/xhci-mtk.h:121 struct member 'speed' not
described in 'mu3h_sch_ep_info'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251104070216.907540-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree binding support for the USB3.2 Gen2 controller on Renesas
RZ/V2H(P) and RZ/V2N SoCs. The USB3.2 IP on these SoCs is identical to
that found on the RZ/G3E SoC.
Add new compatible strings "renesas,r9a09g056-xhci" for RZ/V2N and
"renesas,r9a09g057-xhci" for RZ/V2H(P). Both variants use
"renesas,r9a09g047-xhci" as a fallback compatible to indicate hardware
compatibility with the RZ/G3E implementation.
Update the title to be more generic as it now covers multiple SoC
families beyond just RZ/G3E.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251101042440.648321-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 69896119dc ("MIPS: vdso: Switch to generic storage
implementation") switches to a generic vdso storage, which increases
the number of data pages from 1 to 4. But there is only one page
reserved, which causes segementation faults depending where the VDSO
area is randomized to. To fix this use the same size of reservation
and allocation of the VDSO data pages.
Fixes: 69896119dc ("MIPS: vdso: Switch to generic storage implementation")
Reviewed-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In ima_match_rules(), if ima_filter_rule_match() returns -ENOENT due to
the rule being NULL, the function incorrectly skips the 'if (!rc)' check
and sets 'result = true'. The LSM rule is considered a match, causing
extra files to be measured by IMA.
This issue can be reproduced in the following scenario:
After unloading the SELinux policy module via 'semodule -d', if an IMA
measurement is triggered before ima_lsm_rules is updated,
in ima_match_rules(), the first call to ima_filter_rule_match() returns
-ESTALE. This causes the code to enter the 'if (rc == -ESTALE &&
!rule_reinitialized)' block, perform ima_lsm_copy_rule() and retry. In
ima_lsm_copy_rule(), since the SELinux module has been removed, the rule
becomes NULL, and the second call to ima_filter_rule_match() returns
-ENOENT. This bypasses the 'if (!rc)' check and results in a false match.
Call trace:
selinux_audit_rule_match+0x310/0x3b8
security_audit_rule_match+0x60/0xa0
ima_match_rules+0x2e4/0x4a0
ima_match_policy+0x9c/0x1e8
ima_get_action+0x48/0x60
process_measurement+0xf8/0xa98
ima_bprm_check+0x98/0xd8
security_bprm_check+0x5c/0x78
search_binary_handler+0x6c/0x318
exec_binprm+0x58/0x1b8
bprm_execve+0xb8/0x130
do_execveat_common.isra.0+0x1a8/0x258
__arm64_sys_execve+0x48/0x68
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x44/0x200
el0t_64_sync_handler+0x100/0x130
el0t_64_sync+0x3c8/0x3d0
Fix this by changing 'if (!rc)' to 'if (rc <= 0)' to ensure that error
codes like -ENOENT do not bypass the check and accidentally result in a
successful match.
Fixes: 4af4662fa4 ("integrity: IMA policy")
Signed-off-by: Zhao Yipeng <zhaoyipeng5@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Depending on the particular CPU implementation a TLB shutdown may occur
if multiple matching entries are detected upon the execution of a TLBP
or the TLBWI/TLBWR instructions. Given that we don't know what entries
we have been handed we need to be very careful with the initial TLB
setup and avoid all these instructions.
Therefore read all the TLB entries one by one with the TLBR instruction,
bypassing the content addressing logic, and truncate any large pages in
place so as to avoid a case in the second step where an incoming entry
for a large page at a lower address overlaps with a replacement entry
chosen at another index. Then preinitialize the TLB using addresses
outside our usual unique range and avoiding clashes with any entries
received, before making the usual call to local_flush_tlb_all().
This fixes (at least) R4x00 cores if TLBP hits multiple matching TLB
entries (SGI IP22 PROM for examples sets up all TLBs to the same virtual
address).
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 35ad7e1815 ("MIPS: mm: tlb-r4k: Uniquify TLB entries on init")
Cc: stable@vger.kernel.org
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com> # Boston I6400, M5150 sim
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Common boolean properties need to be only allowed in the binding
(":true"), because their type is already defined by core DT schema.
Simplify dma-coherent property to match common syntax.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Link: https://patch.msgid.link/20251115122120.35315-5-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set the edma tcd transfer attribution settings for the src and dst based
on their respective dma_addr values, to remove the previous 32-byte
alignment limitation in the EDMA memcpy function.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251119163255.502070-1-han.xu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the
unused platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120164907.28007-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There seems to be nothing preventing the driver from being compile
tested so enable that for wider build coverage.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120115016.8967-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20251120114524.8431-10-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120114524.8431-9-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver does not support anything but OF probe since commit
3b0f4a54f2 ("dma:mmp_tdma: get sram pool through device tree").
Commit a67ba97dfb ("dmaengine: Use device_get_match_data()") later
removed most remnants of platform probing except for an unnecessary OF
node check in remove().
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120114524.8431-8-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver does not support anything but OF probe since commit
3b0f4a54f2 ("dma:mmp_tdma: get sram pool through device tree") so drop
the unused platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120114524.8431-7-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120114524.8431-6-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251120114524.8431-5-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251120114524.8431-4-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver does not support anything but OF and ACPI probe since commit
b3757413b9 ("dmaengine: dw: platform: Use struct dw_dma_chip_pdata")
so drop the unused platform module alias along with the now unnecessary
driver name define.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251120114524.8431-3-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251120114524.8431-2-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Allows the buildbot to detect potential issues with the code on various
platforms.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Link: https://patch.msgid.link/20251106022405.85604-3-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
size_t formats under 32-bit evaluate to the same thing and GCC does not
warn against it. Not the case with 64-bit.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Link: https://patch.msgid.link/20251106022405.85604-2-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
GFP_NOWAIT allocation may fail anytime. It needs to be changed to
GFP_NOIO. There's no need to handle an error because mempool_alloc with
GFP_NOIO can't fail.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
This completes 3bc3c9c3ab ("bugs/core: Pass down the condition
string of WARN_ON_ONCE(cond) warnings to __WARN_FLAGS()") and makes
WARN_ON() and WARN_ON_ONCE() behaviour consistent.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251110115757.690999560@infradead.org
Add a report_bug() variant where the bug_entry is already known. This
is useful when the exception instruction is not instantiated per-site.
But instead has a single instance. In such a case the bug_entry
address might be passed along in a known register or something.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251110115757.575795595@infradead.org
Add BUG_FORMAT_ARGS; when an architecture is able to provide a va_list
given pt_regs, use this to print format arguments.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251110115757.457339417@infradead.org
Three repeated CONFIG_GENERIC_BUG_RELATIVE_POINTERS #ifdefs right
after one another yields unreadable code. Add a helper.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251110115757.341703850@infradead.org
Add BUG_FORMAT; an architecture opt-in feature that allows adding the
WARN_printf() format string to the bug_entry table.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251110115757.223371452@infradead.org
Bring in the UDB and objtool data annotations to avoid conflicts while further extending the bug exceptions.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
If the parsed ELD has spk_alloc=0, it currently assigns the parsed ELD
spk_alloc to 0xffff. However, we should also check if there is at least
one SAD (Short audio descriptor) to enforce the assumption, as ELD
without any sad_count, is usually considered invalid for e.g. in
commit ce9778b7a0272("ALSA: hda/hdmi: Consider ELD is invalid when no
SAD is present").
Signed-off-by: Umang Jain <uajain@igalia.com>
Link: https://patch.msgid.link/20251120141757.901505-1-uajain@igalia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The VSIE code currently checks that the BSCA struct fits within
a page, and returns a validity exception 0x003b if it doesn't.
The BSCA is pinned in memory rather than shadowed (see block
comment at end of kvm_s390_cpu_feat_init()), so enforcing the
CPU entries to be on the same pinned page makes sense.
Except those entries aren't going to be used below the guest,
and according to the definition of that validity exception only
the header of the BSCA (everything but the CPU entries) needs to
be within a page. Adjust the alignment check to account for that.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Christoph Schlameuss <schlameuss@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Starting with Zen6, AMD's Scalable MCA systems will incorporate two new bits in
MCA_STATUS and MCA_CONFIG MSRs. These bits will indicate if a valid System
Physical Address (SPA) is present in MCA_ADDR.
PhysAddrValidSupported bit (MCA_CONFIG[11]) serves as the architectural
indicator and states if PhysAddrV bit (MCA_STATUS[54]) is Reserved or if it
indicates validity of SPA in MCA_ADDR.
PhysAddrV bit (MCA_STATUS[54]) advertises if MCA_ADDR contains valid SPA or if
it is implementation specific.
Use and prefer MCA_STATUS[PhysAddrV] when checking for a usable address.
Signed-off-by: Avadhut Naik <avadhut.naik@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/20251118191731.181269-1-avadhut.naik@amd.com
The MCA threshold limit generally is not something that needs to change during
runtime. It is common for a system administrator to decide on a policy for
their managed systems.
If MCA thresholding is OS-managed, then the threshold limit must be set at
every boot. However, many systems allow the user to set a value in their BIOS.
And this is reported through an APEI HEST entry even if thresholding is not in
FW-First mode.
Use this value, if available, to set the OS-managed threshold limit. Users
can still override it through sysfs if desired for testing or debug.
APEI is parsed after MCE is initialized. So reset the thresholding blocks
later to pick up the threshold limit.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20251104-wip-mca-updates-v8-0-66c8eacf67b9@amd.com
Comparing to exactly 1 will fail if more than one ring buffer
event was seen since the last call to timerlat_bpf_wait(), which
can happen in some race scenarios.
Signed-off-by: Crystal Wood <crwood@redhat.com>
Link: https://lore.kernel.org/r/20251112152529.956778-5-crwood@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
The timerlat "top stop at failed action" test was relying on "ALL" being
printed immediately after the "1" from the threshold action. Besides being
fragile, this depends on stdbuf behavior, which is easy to miss when
recreating the test outside of the framework for debugging purposes.
Instead, use the expected/unexpected text mechanism from the
corresponding osnoise test.
Signed-off-by: Crystal Wood <crwood@redhat.com>
Link: https://lore.kernel.org/r/20251112152529.956778-2-crwood@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
When running rtla as
`rtla <timerlat|osnoise> <top|hist> -t custom_file.txt -a 100`
-a options override trace output filename specified by -t option.
Running the command above will create <timerlat|osnoise>_trace.txt file
instead of custom_file.txt. Fix this by making sure that -a option does
not override trace output filename even if it's passed after trace
output filename is specified.
Fixes: 173a3b0148 ("rtla/timerlat: Add the automatic trace option")
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Reviewed-by: Tomas Glozar <tglozar@redhat.com>
Link: https://lore.kernel.org/r/b6ae60424050b2c1c8709e18759adead6012b971.1762186418.git.ipravdin.official@gmail.com
[ use capital letter in subject, as required by tracing subsystem ]
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Currently, user can only specify cgroup to the tracer's thread the
following ways:
`-C[cgroup]`
`-C[=cgroup]`
`--cgroup[=cgroup]`
If user tries to specify cgroup as `-C [cgroup]` or `--cgroup [cgroup]`,
the parser silently fails and rtla's cgroup is used for the tracer
threads.
To make interface more user-friendly, allow user to specify cgroup in
the aforementioned way, i.e. `-C [cgroup]` and `--cgroup [cgroup]`.
Refactor identical logic between -t/--trace and -C/--cgroup into a
common function.
Change documentation to reflect this user interface change.
Fixes: a957cbc025 ("rtla: Add -C cgroup support")
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Reviewed-by: Tomas Glozar <tglozar@redhat.com>
Link: https://lore.kernel.org/r/16132f1565cf5142b5fbd179975be370b529ced7.1762186418.git.ipravdin.official@gmail.com
[ use capital letter in subject, as required by tracing subsystem ]
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
A long time ago, when the usage help was short, it was a favor
to the user to show it on error. Now that the usage help has
become very long, it is too noisy to dump the complete help text
for each typo after the error message itself.
Replace osnoise_hist_usage("...") with fatal("...") on errors.
Remove the already unused 'usage' argument from osnoise_hist_usage().
Signed-off-by: Costa Shulyupin <costa.shul@redhat.com>
Reviewed-by: Tomas Glozar <tglozar@redhat.com>
Link: https://lore.kernel.org/r/20251011082738.173670-6-costa.shul@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
