Ray Lehtiniemi reported that an incoming UDP packet flood can lock up
the ep93xx ethernet driver. Herbert Valerio Riedel noted that due to
the way ep93xx_eth manages the RX/TXstatus rings, it cannot distinguish
a full ring from an empty one, and correctly suggested that this was
likely to be causing this lockup to occur.
Instead of looking at the hardware's RX/TXstatus ring write pointers
to determine when to stop reading from those rings, we should just check
every individual RX/TXstatus descriptor's valid bit instead, since there
is no other way to distinguish an empty ring from a full ring, and if
there is a descriptor waiting, we take the hit of reading the descriptor
from memory anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Wed, 25 Oct 2006 18:03:13 +0200 Toralf Förster wrote:
> WARNING: "arp_broken_ops" [drivers/net/wan/sealevel.ko] undefined!
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Here's the config:
...
> # CONFIG_INET is not set
> CONFIG_SEALEVEL_4021=m
Sealevel uses arp_broken_ops so it needs to depend on INET.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Account for the interface being closed before disabling polling
on a device, to fix shutdown on some systems that explcitly close
the netdevice before calling shutdown.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
On Thu, Oct 12, 2006 at 06:22:14PM +1000, David Gibson wrote:
> Your recent ibmveth commit, 751ae21c6c
> ("fix int rollover panic"), causes a rapid oops on my test machine
> (POWER5 LPAR).
>
> I've bisected it down to that commit, but am still investigating the
> cause of the crash itself.
Found the problem, I believe: an object lesson in the need for great
caution using ++.
[...]
@@ -213,6 +213,7 @@ static void ibmveth_replenish_buffer_poo
}
free_index = pool->consumer_index++ % pool->size;
+ pool->consumer_index = free_index;
index = pool->free_map[free_index];
ibmveth_assert(index != IBM_VETH_INVALID_MAP);
Since the ++ is used as post-increment, the increment is not included
in free_index, and so the added line effectively reverts the
increment. The produced_index side has an analagous bug.
The following change corrects this:
The recent commit 751ae21c6c introduced
a bug in the producer/consumer index calculation in the ibmveth driver
- incautious use of the post-increment ++ operator resulted in an
increment being immediately reverted. This patch corrects the logic.
Without this patch, the driver oopses almost immediately after
activation on at least some machines.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When closing the driver or reinitializing the hardware there is the
usual del_timer() race condition that exists when timers re-add
themselves. Fix by conversion to del_timer_sync().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
changes due to qe_lib changes include:
o removed inclusion of platform header file
o removed platform_device code, replaced with of_device
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o removed irrelevant comments, added others to resemble removed BD_ defines
o const'd and uncasted all get_property() assignments
bugfixes, courtesy of Scott Wood, include:
- Read phy_address as a u32, not u8.
- Match on type == "network" as well as compatible == "ucc_geth", as
device_is_compatible() will only compare up to the length of the
test string, allowing "ucc_geth_phy" to match as well.
- fixes the MAC setting code in ucc_geth.c. The old code was overwriting and dereferencing random stack contents.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The reason sky2 driver was locking up on transmit on the Yukon-FE chipset
is that it was misconfiguring the internal RAM buffer so the transmitter
and receiver were sharing the same space.
The code assumed there was 16K of RAM on Yukon-FE (taken from vendor driver
sk98lin which is even more f*cked up on this). Then it assigned based on that.
The giveaway was that the registers would only hold 9bits so both RX/TX
had 0..1ff for space. It is a wonder it worked at all!
This patch addresses this, and fixes an easily reproducible hang on Transmit.
Only the Yukon-FE chip is Marvell 88E803X (10/100 only) are affected.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During the handling of the PCI error recovery sequence, the current e1000
driver erroneously blocks a device reset for any but the first PCI
function. It shouldn't -- this is a cut-n-paste error from a different
driver (which tolerated only one hardware reset per hardware card).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- move definition of 'tmc' and 'br' locals closer to usage
- handle clock_rate_calc() error
- propagate errors back to upper level open routine
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 4596c75c23 as
requested by Olaf Hering. It causes compile errors, and says Olaf:
"This change is also wrong, the autoloading works perfect with 2.6.18,
no need to add random PCI ids.
See commit a0245f7ad5, platform devices
have now a modalias entry in sysfs. The network card is not a PCI
device."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (36 commits)
[Bluetooth] Fix HID disconnect NULL pointer dereference
[Bluetooth] Add missing entry for Nokia DTL-4 PCMCIA card
[Bluetooth] Add support for newer ANYCOM USB dongles
[NET]: Can use __get_cpu_var() instead of per_cpu() in loopback driver.
[IPV4] inet_peer: Group together avl_left, avl_right, v4daddr to speedup lookups on some CPUS
[TCP]: One NET_INC_STATS() could be NET_INC_STATS_BH in tcp_v4_err()
[NETFILTER]: Missing check for CAP_NET_ADMIN in iptables compat layer
[NETPOLL]: initialize skb for UDP
[IPV6]: Fix route.c warnings when multiple tables are disabled.
[TG3]: Bump driver version and release date.
[TG3]: Add lower bound checks for tx ring size.
[TG3]: Fix set ring params tx ring size implementation
[NET]: reduce per cpu ram used for loopback stats
[IPv6] route: Fix prohibit and blackhole routing decision
[DECNET]: Fix input routing bug
[TCP]: Bound TSO defer time
[IPv4] fib: Remove unused fib_config members
[IPV6]: Always copy rt->u.dst.error when copying a rt6_info.
[IPV6]: Make IPV6_SUBTREES depend on IPV6_MULTIPLE_TABLES.
[IPV6]: Clean up BACKTRACK().
...
When rebooting with netconsole over e100, the driver shutdown code would
deadlock with netpoll. Reduce shutdown code to a bare minimum while retaining
WoL and suspend functionality.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As BHs are off in loopback_xmit(), preemption cannot occurs, so we can
use __get_cpu_var() instead of per_cpu() (and avoid a
preempt_enable()/preempt_disable() pair)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimum tx ring size must be greater than MAX_SKB_FRAGS or 3
times that on some chips with TSO bugs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the implementation of the ethtool set ring parameters for the
tg3 transmit ring. The size of tx_pending is taken into account
before doing a netif_wake_queue. This prevents the interface from
locking up when smaller transmit ring sizes are used.
Signed-off-by: Ranjit Manomohan <ranjitm@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dont need a full struct net_device_stats (currently 23 long : 184 bytes on
x86_64) per possible CPU, but only two counters : bytes and packets
We save few CPU cycles too in loopback_xmit() not updating 4 fields, but 2.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'ubuntu-updates' of master.kernel.org:/pub/scm/linux/kernel/git/bcollins/ubuntu-2.6:
[pci_ids] Add Quicknet XJ vendor/device ID's.
[valkyriefb] Ifdef for when CONFIG_NVRAM isn't enabled.
[platinumfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[igafb] Add pci dev table for module auto loading.
[controlfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[hid-core] TurboX Keyboard needs NOGET quirk.
[ixj] Add pci dev table for module auto loading.
[initio] Add pci dev table for module auto loading.
[fdomain] Add pci dev table for module auto loading.
[BusLogic] Add pci dev table for auto module loading.
[mv643xx] Add pci device table for auto module loading.
[alim7101] Add pci dev table for auto module loading.
This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it hangs after a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
When using flow control, the PHY needs to accept multicast pause frames.
Without this fix, these frames were getting discarded by the PHY before
doing any flow control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Under high load it is possible to make the receiver FIFO get overloaded.
The driver/hardware recover properly, so there is no reason to fill the log
with lots of extra messages, just update counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of flow control negotiation should not limit the next
negotiatition. If board is plugged into an old half duplex 10Mbit port,
without pause, then replugged into a gigabit port, it should negotiate
what is desired, not inherit that last negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of duplex negotiation is avaliable in the phy status
register, so use that to simplify code and avoid rereading the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
