This will show the gpio chip as a child node
under /sys/bus/pci/devices/xxxx:xx:xx.x/
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix below build errors:
CC [M] drivers/gpio/gpio-em.o
drivers/gpio/gpio-em.c: In function 'em_gio_probe':
drivers/gpio/gpio-em.c:306: error: 'err' undeclared (first use in this function)
drivers/gpio/gpio-em.c:306: error: (Each undeclared identifier is reported only once
drivers/gpio/gpio-em.c:306: error: for each function it appears in.)
drivers/gpio/gpio-em.c:308: error: label 'err3' used but not defined
drivers/gpio/gpio-em.c:279: error: label 'err2' used but not defined
drivers/gpio/gpio-em.c:265: error: label 'err1' used but not defined
drivers/gpio/gpio-em.c:250: error: label 'err0' used but not defined
drivers/gpio/gpio-em.c:309: warning: no return statement in function returning non-void
drivers/gpio/gpio-em.c: At top level:
drivers/gpio/gpio-em.c:311: error: expected identifier or '(' before 'if'
drivers/gpio/gpio-em.c:317: error: expected identifier or '(' before 'if'
drivers/gpio/gpio-em.c:323: warning: data definition has no type or storage class
drivers/gpio/gpio-em.c:323: warning: type defaults to 'int' in declaration of 'ret'
drivers/gpio/gpio-em.c:323: error: 'gpio_chip' undeclared here (not in a function)
drivers/gpio/gpio-em.c:323: error: initializer element is not constant
drivers/gpio/gpio-em.c:324: error: expected identifier or '(' before 'if'
drivers/gpio/gpio-em.c:328: error: expected identifier or '(' before 'return'
drivers/gpio/gpio-em.c:330: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:332: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:334: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:336: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:338: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:340: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:342: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token
drivers/gpio/gpio-em.c:344: error: expected identifier or '(' before '}' token
drivers/gpio/gpio-em.c: In function 'em_gio_remove':
drivers/gpio/gpio-em.c:361: error: implicit declaration of function 'em_gio_irq_domain_cleanup'
make[2]: *** [drivers/gpio/gpio-em.o] Error 1
make[1]: *** [drivers/gpio] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The following chips need to enable internal settings to let ASPM
and clock request work.
RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the Versatile FPGA interrupt controller driver, used in
the Integrator/AP, Integrator/CP and some Versatile boards, out
of arch/arm/plat-versatile and down to drivers/irqchip where we
have consensus that such drivers belong. The header file is
consequently moved to <linux/platform_data/irq-versatile-fpga.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The adis16334 has the PROD_ID register so set the PROD_ID flag in its chip info.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADIS1360 and ADIS13605 are very similar and do have the same software
interface. The only difference is the contents of the PROD_ID register. Since we
now read the product id from the device name instead of the chip_info struct we
can use the same chip_table entry for both the ADIS1360 and ADIS13605.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The product id check currently ANDs the read id with 0xF000 and compares the
result to the product id from the chip info. Since none of the product ids in
the chip info table end in 0x000 the check will always fail. Furthermore it is
also wrong, the product id in the PROD_ID register will always match the part
number of the device.
Some of the ADIS16XXX devices are identical from a software point of
view with the product id register having a different content. If we keep the
current scheme of storing the product id in the chip info table this would
require us to have multiple almost identical chip info table entries. So instead
this patch changes the code to parse the product id from the device name.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Setting the sampling frequency for the adis16334 differs from the other devices.
This patch introduces two new callback functions to the adis16400 chip_info
struct which are used to specify how to read and write the current sample rate.
The patch also introduces the proper implementations for these callbacks for the
adis16334.
Related to this is that the adis16334 has no slow mode and so we do not limit
the SPI clock rate to 300kHz during initialization. The patch adds a new flag
for devices which do have a slow mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While copying the argument structures in HYPERVISOR_event_channel_op()
and HYPERVISOR_physdev_op() into the local variable is sufficiently
safe even if the actual structure is smaller than the container one,
copying back eventual output values the same way isn't: This may
collide with on-stack variables (particularly "rc") which may change
between the first and second memcpy() (i.e. the second memcpy() could
discard that change).
Move the fallback code into out-of-line functions, and handle all of
the operations known by this old a hypervisor individually: Some don't
require copying back anything at all, and for the rest use the
individual argument structures' sizes rather than the container's.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[v2: Reduce #define/#undef usage in HYPERVISOR_physdev_op_compat().]
[v3: Fix compile errors when modules use said hypercalls]
[v4: Add xen_ prefix to the HYPERCALL_..]
[v5: Alter the name and only EXPORT_SYMBOL_GPL one of them]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch contains fixes for persistent grants implementation v2:
* handle == 0 is a valid handle, so initialize grants in blkback
setting the handle to BLKBACK_INVALID_HANDLE instead of 0. Reported
by Konrad Rzeszutek Wilk.
* new_map is a boolean, use "true" or "false" instead of 1 and 0.
Reported by Konrad Rzeszutek Wilk.
* blkfront announces the persistent-grants feature as
feature-persistent-grants, use feature-persistent instead which is
consistent with blkback and the public Xen headers.
* Add a consistency check in blkfront to make sure we don't try to
access segments that have not been set.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Roger Pau Monne <roger.pau@citrix.com>
[v1: The new_map int->bool had already been changed]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When the UART device has hardware flow control enabled, it ignores the
MCR RTS bit in the MCR register, and keeps RTS asserted as long as we
continue to read characters from the UART receiver FIFO. This means
that when the TTY buffers become full, the UART doesn't tell the remote
end to stop sending, which causes the TTY layer to start dropping
characters.
A similar problem exists with software flow control. We need the FIFO
register to fill when software flow control is enabled to provoke the
UART to send the XOFF character.
Fix this by implementing the throttle/unthrottle callbacks, and use
these to disable receiver interrupts. This in turn means that the UART
FIFO will fill, which will then cause the UART's hardware to deassert
the RTS signal and/or send the XOFF character, stopping the remote end.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simplify:
- set ECB
...
- LCR mode A
- clear TCRTLR
- LCR mode B
- clear ECB
- set ECB and update other bits
- LCR mode A
- update XONANY
to:
- set ECB
...
- LCR mode B
- set ECB and update other bits
- LCR mode A
- update XONANY and clear TCRTLR
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Take advantage of the switch to mode B for accessing the TCR register,
and move the xon/xoff configuration there. This allows further
simplication of this sequence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always setup the TCR register in the software flow control path,
and when hardware flow control is enabled. Remove this redundant
setup, and place it before we setup any hardware flow control.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have the sequence:
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
This can be simplified to:
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's really no reason to read back these registers while setting
the termios modes, provided we keep our cached copies up to date.
Remove these readbacks.
This has the benefit that we know that the EFR_ECB and MCR_TCRTLR
bits will always be clear, so we don't need to keep masking these
bits throughout the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_pending is never used, so let's remove it. It seems to be result
of a bad rebase of d37c6cebcb (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:
- serial_omap_configure_xonxoff() was attempting to clear the bit after
explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
SCR, and when trying to change the TCR register when hardware flow
control was enabled.
Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.
Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits. Ensure
that these bits always start off in a known state.
In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
c538d20c7f (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register. This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it. The last value which was written to this
register was up->efr.
Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program. As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt. Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it. Clear this
bit when IXANY mode is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add two callbacks for hardware assisted flow control; we need to know
when the tty layers want us to stop and restart due to their buffer
levels.
Call a driver specific throttle/unthrottle function if and only if the
driver indicates that it is using an enabled hardware assisted flow
control method, otherwise fall back to the non-hardware assisted
methods.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ports which are handling h/w flow control in hardware must not have
their RTS state altered depending on the tty's hardware-stopped state.
Avoid this additional logic when setting the termios state.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ports which are capable of handling s/w flow control in hardware to
know when the s/w flow control termios settings are changed. Add a
flag to allow the low level serial drivers to indicate that they
support this, and these changes should be propagated to them.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fetches the pinctrl resource for the MMCI driver, and if
a "default" state is found, it is activated.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the ARM machine identifier to sortextable and select the
config option so that we can sort the exception table at compile
time. sortextable relies on a section named __ex_table existing
in the vmlinux, but ARM's linker script places the exception
table in the data section. Give the exception table its own
section so that sortextable can find it.
This allows us to skip the sorting step during boot.
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It has been brought to my knowledge that the .setup()/.stop()
function pair in the SMP TWD is going to be called from atomic
contexts for CPUs coming and going, and then the
clk_prepare()/clk_unprepare() calls cannot be called
on subsequent .setup()/.stop() iterations. This is however
just the tip of an iceberg as the function pair is not
designed to be reentrant at all.
This change makes the SMP_TWD clock .setup()/.stop() pair reentrant
by splitting the .setup() function in three parts:
- One COMMON part that is executed the first time the first CPU
in the TWD cluster is initialized. This will fetch the TWD
clk for the cluster and prepare+enable it. If no clk is
available it will calibrate the rate instead.
- One part that is executed the FIRST TIME a certain CPU is
brought on-line. This initializes and sets up the clock event
for a certain CPU.
- One part that is executed on every subsequent .setup() call.
This will re-initialize the clock event. This is augmented
to call the clk_enable()/clk_disable() pair properly.
Cc: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A minor code refactoring saving a few lines by merging prepare()
and enable() calls.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The audio chipset used in Teradici's Tera2 host cards is the same as that in
the 1200 host cards. This patch allows ALSA to recognize the Tera2 cards.
Signed-off-by: Lars R. Damerow <lars@pixar.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Starting audio or seeking in various music players causes
setup_dig_out_stream() to be called, which resets the SPDIF stream,
which caused one DAC (but not another) to make a clicking noise every
time.
This patch ensures the reset only happens when it needs to, which is
when the format changes, and makes the code a little more readable.
Signed-off-by: Laurence Darby <ldarby@tuffmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of issuing (0) statements when !CONFIG_SYSFS which will cause
'warning: ', we'll use inline statements instead. This will effectively
do the same thing, but suppress any unnecessary warnings.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: bridge@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've observed that in case if UDP diag module is not
supported in kernel the netlink returns NLMSG_DONE without
notifying a caller that handler is missed.
This patch makes __inet_diag_dump to return error code instead.
So as example it become possible to detect such situation
and handle it gracefully on userspace level.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: David Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set APPLE_ISO_KEYBOARD flag on USB_DEVICE_ID_APPLE_GEYSER4_HF_ISO so we get
the ISO translation on German keyboards for the MacBook4,1 as well.
Signed-off-by: Johannes Thumshirn <morbidrsa@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If drbd_adm_attach failed early, it left the CONFIG_PENDING bit on,
blocking any further conn_reconfig_start on that connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
