Commit graph

349,476 commits

Author SHA1 Message Date
Jan Beulich
bd52276fa1 x86-64/efi: Use EFI to deal with platform wall clock (again)
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.

Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).

Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).

Also make the two EFI functions in question here static -
they're not being referenced elsewhere.

History:

    This commit was originally merged as bacef661ac ("x86-64/efi:
    Use EFI to deal with platform wall clock") but it resulted in some
    ASUS machines no longer booting due to a firmware bug, and so was
    reverted in f026cfa82f. A pre-emptive fix for the buggy ASUS
    firmware was merged in 03a1c254975e ("x86, efi: 1:1 pagetable
    mapping for virtual EFI calls") so now this patch can be
    reapplied.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com> [added commit history]
2012-10-30 10:39:20 +00:00
Xiaoyan Zhang
da5a108d05 x86/kernel: remove tboot 1:1 page table creation code
For TXT boot, while Linux kernel trys to shutdown/S3/S4/reboot, it
need to jump back to tboot code and do TXT teardown work. Previously
kernel zapped all mem page identity mapping (va=pa) after booting, so
tboot code mem address was mapped again with identity mapping. Now
kernel didn't zap the identity mapping page table, so tboot related
code can remove the remapping code before trapping back now.

Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Acked-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:20 +00:00
Matt Fleming
185034e72d x86, efi: 1:1 pagetable mapping for virtual EFI calls
Some firmware still needs a 1:1 (virt->phys) mapping even after we've
called SetVirtualAddressMap(). So install the mapping alongside our
existing kernel mapping whenever we make EFI calls in virtual mode.

This bug was discovered on ASUS machines where the firmware
implementation of GetTime() accesses the RTC device via physical
addresses, even though that's bogus per the UEFI spec since we've
informed the firmware via SetVirtualAddressMap() that the boottime
memory map is no longer valid.

This bug seems to be present in a lot of consumer devices, so there's
not a lot we can do about this spec violation apart from workaround
it.

Cc: JérômeCarretero <cJ-ko@zougloub.eu>
Cc: Vasco Dias <rafa.vasco@gmail.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:19 +00:00
Matt Fleming
53b87cf088 x86, mm: Include the entire kernel memory map in trampoline_pgd
There are various pieces of code in arch/x86 that require a page table
with an identity mapping. Make trampoline_pgd a proper kernel page
table, it currently only includes the kernel text and module space
mapping.

One new feature of trampoline_pgd is that it now has mappings for the
physical I/O device addresses, which are inserted at ioremap()
time. Some broken implementations of EFI firmware require these
mappings to always be around.

Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:19 +00:00
Matt Fleming
e913ca7d16 efivarfs: Add documentation for the EFI variable filesystem
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:18 +00:00
Lee, Chun-Yi
605e70c7aa efi: add efivars kobject to efi sysfs folder
UEFI variable filesystem need a new mount point, so this patch add
efivars kobject to efi_kobj for create a /sys/firmware/efi/efivars
folder.

Cc: Matthew Garrett <mjg@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:18 +00:00
Jeremy Kerr
0c542edde3 efi: Handle deletions and size changes in efivarfs_write_file
A write to an efivarfs file will not always result in a variable of
'count' size after the EFI SetVariable() call. We may have appended to
the existing data (ie, with the EFI_VARIABLE_APPEND_WRITE attribute), or
even have deleted the variable (with an authenticated variable update,
with a zero datasize).

This change re-reads the updated variable from firmware, to check for
size changes and deletions. In the latter case, we need to drop the
dentry.

Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:17 +00:00
Matthew Garrett
5d9db88376 efi: Add support for a UEFI variable filesystem
The existing EFI variables code only supports variables of up to 1024
bytes. This limitation existed in version 0.99 of the EFI specification,
but was removed before any full releases. Since variables can now be
larger than a single page, sysfs isn't the best interface for this. So,
instead, let's add a filesystem. Variables can be read, written and
created, with the first 4 bytes of each variable representing its UEFI
attributes. The create() method doesn't actually commit to flash since
zero-length variables can't exist per-spec.

Updates from Jeremy Kerr <jeremy.kerr@canonical.com>.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2012-10-30 10:39:16 +00:00
Takashi Iwai
a5d00dc3a4 Merge branch 'for-linus' into for-next
... for migrating the core changes for USB-audio disconnection fixes
2012-10-30 11:08:25 +01:00
Takashi Iwai
0914f7961b ALSA: Avoid endless sleep after disconnect
When disconnect callback is called, each component should wake up
sleepers and check card->shutdown flag for avoiding the endless sleep
blocking the proper resource release.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:07:15 +01:00
Takashi Iwai
a0830dbd4e ALSA: Add a reference counter to card instance
For more strict protection for wild disconnections, a refcount is
introduced to the card instance, and let it up/down when an object is
referred via snd_lookup_*() in the open ops.

The free-after-last-close check is also changed to check this refcount
instead of the empty list, too.

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:07:10 +01:00
Takashi Iwai
888ea7d5ac ALSA: usb-audio: Fix races at disconnection in mixer_quirks.c
Similar like the previous commit, cover with chip->shutdown_rwsem
and chip->shutdown checks.

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:07:05 +01:00
Takashi Iwai
34f3c89fda ALSA: usb-audio: Use rwsem for disconnect protection
Replace mutex with rwsem for codec->shutdown protection so that
concurrent accesses are allowed.

Also add the protection to snd_usb_autosuspend() and
snd_usb_autoresume(), too.

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:07:00 +01:00
Takashi Iwai
978520b75f ALSA: usb-audio: Fix races at disconnection
Close some races at disconnection of a USB audio device by adding the
chip->shutdown_mutex and chip->shutdown check at appropriate places.

The spots to put bandaids are:
- PCM prepare, hw_params and hw_free
- where the usb device is accessed for communication or get speed, in
 mixer.c and others; the device speed is now cached in subs->speed
 instead of accessing to chip->dev

The accesses in PCM open and close don't need the mutex protection
because these are already handled in the core PCM disconnection code.

The autosuspend/autoresume codes are still uncovered by this patch
because of possible mutex deadlocks.  They'll be covered by the
upcoming change to rwsem.

Also the mixer codes are untouched, too.  These will be fixed in
another patch, too.

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:06:54 +01:00
Takashi Iwai
9b0573c07f ALSA: PCM: Fix some races at disconnection
Fix races at PCM disconnection:
- while a PCM device is being opened or closed
- while the PCM state is being changed without lock in prepare,
  hw_params, hw_free ops

Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 11:06:48 +01:00
Paul Mackerras
8b5869ad85 KVM: PPC: Book3S HV: Fix thinko in try_lock_hpte()
This fixes an error in the inline asm in try_lock_hpte() where we
were erroneously using a register number as an immediate operand.
The bug only affects an error path, and in fact the code will still
work as long as the compiler chooses some register other than r0
for the "bits" variable.  Nevertheless it should still be fixed.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:59 +01:00
Paul Mackerras
9f8c8c7812 KVM: PPC: Book3S HV: Allow DTL to be set to address 0, length 0
Commit 55b665b026 ("KVM: PPC: Book3S HV: Provide a way for userspace
to get/set per-vCPU areas") includes a check on the length of the
dispatch trace log (DTL) to make sure the buffer is at least one entry
long.  This is appropriate when registering a buffer, but the
interface also allows for any existing buffer to be unregistered by
specifying a zero address.  In this case the length check is not
appropriate.  This makes the check conditional on the address being
non-zero.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:58 +01:00
Paul Mackerras
c7b676709c KVM: PPC: Book3S HV: Fix accounting of stolen time
Currently the code that accounts stolen time tends to overestimate the
stolen time, and will sometimes report more stolen time in a DTL
(dispatch trace log) entry than has elapsed since the last DTL entry.
This can cause guests to underflow the user or system time measured
for some tasks, leading to ridiculous CPU percentages and total runtimes
being reported by top and other utilities.

In addition, the current code was designed for the previous policy where
a vcore would only run when all the vcpus in it were runnable, and so
only counted stolen time on a per-vcore basis.  Now that a vcore can
run while some of the vcpus in it are doing other things in the kernel
(e.g. handling a page fault), we need to count the time when a vcpu task
is preempted while it is not running as part of a vcore as stolen also.

To do this, we bring back the BUSY_IN_HOST vcpu state and extend the
vcpu_load/put functions to count preemption time while the vcpu is
in that state.  Handling the transitions between the RUNNING and
BUSY_IN_HOST states requires checking and updating two variables
(accumulated time stolen and time last preempted), so we add a new
spinlock, vcpu->arch.tbacct_lock.  This protects both the per-vcpu
stolen/preempt-time variables, and the per-vcore variables while this
vcpu is running the vcore.

Finally, we now don't count time spent in userspace as stolen time.
The task could be executing in userspace on behalf of the vcpu, or
it could be preempted, or the vcpu could be genuinely stopped.  Since
we have no way of dividing up the time between these cases, we don't
count any of it as stolen.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:57 +01:00
Paul Mackerras
8455d79e21 KVM: PPC: Book3S HV: Run virtual core whenever any vcpus in it can run
Currently the Book3S HV code implements a policy on multi-threaded
processors (i.e. POWER7) that requires all of the active vcpus in a
virtual core to be ready to run before we run the virtual core.
However, that causes problems on reset, because reset stops all vcpus
except vcpu 0, and can also reduce throughput since all four threads
in a virtual core have to wait whenever any one of them hits a
hypervisor page fault.

This relaxes the policy, allowing the virtual core to run as soon as
any vcpu in it is runnable.  With this, the KVMPPC_VCPU_STOPPED state
and the KVMPPC_VCPU_BUSY_IN_HOST state have been combined into a single
KVMPPC_VCPU_NOTREADY state, since we no longer need to distinguish
between them.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:56 +01:00
Paul Mackerras
2f12f03436 KVM: PPC: Book3S HV: Fixes for late-joining threads
If a thread in a virtual core becomes runnable while other threads
in the same virtual core are already running in the guest, it is
possible for the latecomer to join the others on the core without
first pulling them all out of the guest.  Currently this only happens
rarely, when a vcpu is first started.  This fixes some bugs and
omissions in the code in this case.

First, we need to check for VPA updates for the latecomer and make
a DTL entry for it.  Secondly, if it comes along while the master
vcpu is doing a VPA update, we don't need to do anything since the
master will pick it up in kvmppc_run_core.  To handle this correctly
we introduce a new vcore state, VCORE_STARTING.  Thirdly, there is
a race because we currently clear the hardware thread's hwthread_req
before waiting to see it get to nap.  A latecomer thread could have
its hwthread_req cleared before it gets to test it, and therefore
never increment the nap_count, leading to messages about wait_for_nap
timeouts.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:55 +01:00
Paul Mackerras
913d3ff9a3 KVM: PPC: Book3s HV: Don't access runnable threads list without vcore lock
There were a few places where we were traversing the list of runnable
threads in a virtual core, i.e. vc->runnable_threads, without holding
the vcore spinlock.  This extends the places where we hold the vcore
spinlock to cover everywhere that we traverse that list.

Since we possibly need to sleep inside kvmppc_book3s_hv_page_fault,
this moves the call of it from kvmppc_handle_exit out to
kvmppc_vcpu_run, where we don't hold the vcore lock.

In kvmppc_vcore_blocked, we don't actually need to check whether
all vcpus are ceded and don't have any pending exceptions, since the
caller has already done that.  The caller (kvmppc_run_vcpu) wasn't
actually checking for pending exceptions, so we add that.

The change of if to while in kvmppc_run_vcpu is to make sure that we
never call kvmppc_remove_runnable() when the vcore state is RUNNING or
EXITING.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:55 +01:00
Paul Mackerras
7b444c6710 KVM: PPC: Book3S HV: Fix some races in starting secondary threads
Subsequent patches implementing in-kernel XICS emulation will make it
possible for IPIs to arrive at secondary threads at arbitrary times.
This fixes some races in how we start the secondary threads, which
if not fixed could lead to occasional crashes of the host kernel.

This makes sure that (a) we have grabbed all the secondary threads,
and verified that they are no longer in the kernel, before we start
any thread, (b) that the secondary thread loads its vcpu pointer
after clearing the IPI that woke it up (so we don't miss a wakeup),
and (c) that the secondary thread clears its vcpu pointer before
incrementing the nap count.  It also removes unnecessary setting
of the vcpu and vcore pointers in the paca in kvmppc_core_vcpu_load.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:54 +01:00
Paul Mackerras
512691d490 KVM: PPC: Book3S HV: Allow KVM guests to stop secondary threads coming online
When a Book3S HV KVM guest is running, we need the host to be in
single-thread mode, that is, all of the cores (or at least all of
the cores where the KVM guest could run) to be running only one
active hardware thread.  This is because of the hardware restriction
in POWER processors that all of the hardware threads in the core
must be in the same logical partition.  Complying with this restriction
is much easier if, from the host kernel's point of view, only one
hardware thread is active.

This adds two hooks in the SMP hotplug code to allow the KVM code to
make sure that secondary threads (i.e. hardware threads other than
thread 0) cannot come online while any KVM guest exists.  The KVM
code still has to check that any core where it runs a guest has the
secondary threads offline, but having done that check it can now be
sure that they will not come online while the guest is running.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:53 +01:00
Alexander Graf
c99ec973a6 PPC: ePAPR: Convert header to uapi
The new uapi framework splits kernel internal and user space exported
bits of header files more cleanly. Adjust the ePAPR header accordingly.

Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:52 +01:00
Alexander Graf
388cf9ee3c KVM: PPC: Move mtspr/mfspr emulation into own functions
The mtspr/mfspr emulation code became quite big over time. Move it
into its own function so things stay more readable.

Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:51 +01:00
Alexander Graf
686de182a2 KVM: Documentation: Fix reentry-to-be-consistent paragraph
All user space offloaded instruction emulation needs to reenter kvm
to produce consistent state again. Fix the section in the documentation
to mention all of them.

Signed-off-by: Alexander Graf <agraf@suse.de>
2012-10-30 10:54:50 +01:00
Alexander Graf
e43a028752 KVM: PPC: 44x: fix DCR read/write
When remembering the direction of a DCR transaction, we should write
to the same variable that we interpret on later when doing vcpu_run
again.

Signed-off-by: Alexander Graf <agraf@suse.de>
Cc: stable@vger.kernel.org
2012-10-30 10:54:50 +01:00
Takashi Iwai
1a8506d440 ALSA: hda - Add tracepoints to HD-audio controller driver
Add a couple of tracepoints to snd-hda-intel for tracing the position
and the trigger timings.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-10-30 10:39:59 +01:00
Mike Galbraith
5258f386ea sched/autogroup: Fix crash on reboot when autogroup is disabled
Due to these two commits:

  8323f26ce3 sched: Fix race in task_group()
  800d4d30c8 sched, autogroup: Stop going ahead if autogroup is disabled

... autogroup scheduling's dynamic knobs are wrecked.

With both patches applied, all you have to do to crash a box is
disable autogroup during boot up, then reboot.. boom, NULL pointer
dereference due to 800d4d30 not allowing autogroup to move things,
and 8323f26ce making that the only way to switch runqueues.

Remove most of the (dysfunctional) knobs and turn the remaining
sched_autogroup_enabled knob readonly.

If the user fiddles with cgroups hereafter, once tasks
are moved, autogroup won't mess with them again unless
they call setsid().

No knobs, no glitz, nada, just a cute little thing folks can
turn on if they don't want to muck about with cgroups and/or
systemd.

Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xiaotian Feng <dannyfeng@tencent.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org> # v3.6
Link: http://lkml.kernel.org/r/1351451963.4999.8.camel@maggy.simpson.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:26:04 +01:00
Liu Bo
52b1de91ea btrfs: unpin_extent_cache: fix the typo and unnecessary arguements
- unpint->unpin
- prealloc is no more used

Signed-off-by: Liu Bo <liub.liubo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-10-30 10:18:50 +01:00
Maxime Bizon
37aeec3622 x86/ce4100: Fix PCI configuration register access for devices without interrupts
Some CE4100 devices such as the:

 - DFX module (01:0b.7)
 - entertainment encryption device (01:10.0)
 - multimedia controller (01:12.0)

do not have a device interrupt at all.

This patch fixes the PCI controller code to declare the missing
PCI configuration register space, as well as a fixup method for
forcing the interrupt pin to be 0 for these devices. This is
required to ensure that pci drivers matching on these devices
will be able to honor the various PCI subsystem calls touching
the configuration space.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: rui.zhang@intel.com
Cc: alan@linux.intel.com
Link: http://lkml.kernel.org/r/1351518020-25556-4-git-send-email-ffainelli@freebox.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:16:47 +01:00
Maxime Bizon
d795991602 x86/ce4100: Fix reboot by forcing the reboot method to be KBD
The default reboot is via ACPI for this platform, and the CEFDK
bootloader actually supports this, but will issue a system power
off instead of a real reboot. Setting the reboot method to be
KBD instead of ACPI ensures proper system reboot.

Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: rui.zhang@intel.com
Cc: alan@linux.intel.com
Link: http://lkml.kernel.org/r/1351518020-25556-3-git-send-email-ffainelli@freebox.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:16:46 +01:00
Florian Fainelli
f49f4ab95c x86/ce4100: Fix pm_poweroff
The CE4100 platform is currently missing a proper pm_poweroff
implementation leading to poweroff making the CPU spin forever
and the CE4100 platform does not enter a low-power mode where
the external Power Management Unit can properly power off the
system. Power off on this platform is implemented pretty much
like reboot, by writing to the SoC built-in 8051 microcontroller
mapped at I/O port 0xcf9, the value 0x4.

Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: rui.zhang@intel.com
Cc: alan@linux.intel.com
Link: http://lkml.kernel.org/r/1351518020-25556-2-git-send-email-ffainelli@freebox.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:16:46 +01:00
Peter Huewe
95d18aa2b6 perf/x86: Fix sparse warnings
FYI, there are new sparse warnings:

 arch/x86/kernel/cpu/perf_event.c:1356:18: sparse: symbol 'events_attr' was not declared. Should it be static?

This patch makes it static and also adds the static keyword to
fix arch/x86/kernel/cpu/perf_event.c:1344:9: warning: symbol
'events_sysfs_show' was not declared.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: fengguang.wu@intel.com
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/n/tip-lerdpXlnruh0yvWs2owwuizl@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:10:52 +01:00
Michael Neuling
0d855354ea perf, powerpc: Fix hw breakpoints returning -ENOSPC
I've been trying to get hardware breakpoints with perf to work
on POWER7 but I'm getting the following:

  % perf record -e mem:0x10000000 true

    Error: sys_perf_event_open() syscall returned with 28 (No space left on device).  /bin/dmesg may provide additional information.

    Fatal: No CONFIG_PERF_EVENTS=y kernel support configured?

  true: Terminated

(FWIW adding -a and it works fine)

Debugging it seems that __reserve_bp_slot() is returning ENOSPC
because it thinks there are no free breakpoint slots on this
CPU.

I have a 2 CPUs, so perf userspace is doing two perf_event_open
syscalls to add a counter to each CPU [1].  The first syscall
succeeds but the second is failing.

On this second syscall, fetch_bp_busy_slots() sets slots.pinned
to be 1, despite there being no breakpoint on this CPU.  This is
because the call the task_bp_pinned, checks all CPUs, rather
than just the current CPU. POWER7 only has one hardware
breakpoint per CPU (ie. HBP_NUM=1), so we return ENOSPC.

The following patch fixes this by checking the associated CPU
for each breakpoint in task_bp_pinned.  I'm not familiar with
this code, so it's provided as a reference to the above issue.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Jovi Zhang <bookjovi@gmail.com>
Cc: K Prasad <prasad@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1351268936-2956-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:07:58 +01:00
Robert Richter
4cf7e71869 MAINTAINERS: Update email address for Robert Richter
Signed-off-by: Robert Richter <rric@kernel.org>
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: lm-sensors@lm-sensors.org
Cc: oprofile-list@lists.sf.net
Cc: Stephane Eranian <eranian@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: =?iso-8859-1?Q?J=F6rg_R=F6del?= <joro@8bytes.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: http://lkml.kernel.org/r/20121029175325.GE5024@tweety
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:05:52 +01:00
Andreas Herrmann
943482d07e x86, microcode_amd: Change email addresses, MAINTAINERS entry
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: lm-sensors@lm-sensors.org
Cc: oprofile-list@lists.sf.net
Cc: Stephane Eranian <eranian@google.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jorg Roedel <joro@8bytes.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: http://lkml.kernel.org/r/20121029175138.GC5024@tweety
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:05:52 +01:00
Borislav Petkov
487ba8e82a MAINTAINERS: Change Boris' email address
Move to private mail address.

Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1351532410-4887-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:05:51 +01:00
Borislav Petkov
43aff26ce1 EDAC: Change Boris' email address
My @amd.com address will be invalid soon so move to private
email address.

Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1351532410-4887-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:05:51 +01:00
Borislav Petkov
e6d41e8c69 x86, AMD: Change Boris' email address
Move to private email and put in maintained status.

Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1351532410-4887-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-10-30 10:05:50 +01:00
Johannes Berg
50febf6a1a mac80211: use a counter for remain-on-channel cookie
Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:33:40 +01:00
Wei Yongjun
5a6a86121f ARM: davinci: fix return value check by using IS_ERR in tnetv107x_devices_init()
In case of error, the function clk_get() returns ERR_PTR() not
NULL pointer. The NULL test in the error handling should be
replaced with IS_ERR().

dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2012-10-30 14:03:31 +05:30
Johannes Berg
8a2fbedcdc mac80211: combine status/drop reporting
The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.

However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.

Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.

While at it, also simplify the code in the
nl80211 portion a bit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:33:23 +01:00
Masanari Iida
6efb3c0a2c qla2xxx: Fix typo in qla2xxx drivers
Correct spelling typo in debug messages within qla2xxx drivers.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-10-30 09:27:07 +01:00
Johannes Berg
cbc668a705 mac80211_hwsim: print per interface TX power
Just for debugging, print the interface TX
power whenever it changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:35 +01:00
Johannes Berg
1ea6f9c0d4 mac80211: handle TX power per virtual interface
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:34 +01:00
Johannes Berg
c8442118ad cfg80211: allow per interface TX power setting
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:34 +01:00
Johannes Berg
71fe96bf9d nl80211: move "can set channel" check
Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:33 +01:00
Johannes Berg
e826117142 mac80211_hwsim: allow using channel contexts
To use mac80211_hwsim for testing channel contexts it
has to support them, and for that it has to support
hw scan and hw-remain-on-channel.

Since it's pure software, the off-channel activities
are really not off-channel but listening and sending
on a second channel. Also, the multi-channel isn't
really doing TDM, it's just on both channels at the
same time.

For testing purposes, you can specify the number of
concurrent channels with a module parameter, it is
set to one by default. When set to two or more, the
userspace API for wmediumd is disabled as it has no
provisions for multi-channel yet.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-30 09:11:33 +01:00
Johannes Berg
6fb47de9cf Merge remote-tracking branch 'wireless-next/master' into mac80211-next 2012-10-30 09:09:48 +01:00