This patch modifies the sram allocator to allocate memory
from the DA8XX shared RAM.
Regression tested suspend/resume on AM180x EVM.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
[rebased onto consolidated SRAM patches]
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
[rebased to mainline as consolidated SRAM patches were dropped]
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The current davinci init sets up SRAM in iotables. There has been
an observed failure to boot a da850 with 128K specified in the
iotable.
Make the davinci sram allocator do an ioremap of the region
specified by the entries in davinci_soc_info before registering
with gen_pool_add_virt(). Remove all iotable SRAM mappings and
SRAM_VIRT.
Regression tested suspend/resume on AM180x EVM.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove the use of the private DaVinci SRAM API in favor
of genalloc. The pool to be used is provided by platform
data.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: "Hans J. Koch" <hjk@hansjkoch.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Provide an API to initialize a UART clock. Refactor existing
davinci_serial_init() to separate out the part which enables
the clock.
This will later be used to help DA850 DT boot support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Building a multiplatform kernel with combined armv7 and armv6
kernel does not work with the socfpga smp code, which contains
v7-only instructions. Since this code never runs on armv6,
we can annotate the assmebly with .arch armv7-a, as suggested
by Russell King.
[arnd: reword commit message]
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CODA_7541 is the coda_product type for mx53.
The 'driver_data' for mx53 is CODA_IMX53 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 136b5721d (workqueue: deprecate __cancel_delayed_work()) made
__cancel_delayed_work deprecated. Use cancel_delayed_work instead and get rid of
the following warning:
drivers/media/platform/coda.c:1543: warning: '__cancel_delayed_work' is deprecated (declared at include/linux/workqueue.h:437)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As G-Scaler is going to stay unchanged across all exynos5 series
SoCs, changing the driver compatible string name to
"samsung,exynos5-gsc" from "samsung,exynos5250-gsc".
This change is as per the discussion in the devicetree forum.
http://www.mail-archive.com/devicetree-discuss@lists.ozlabs.org/msg16448.html
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joe pointed out that I forgot to remove the documentation, so do that
here.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With kernel 3.6 some obsolete SCSI-2 commands including SEEK_10 have
have been removed by commit 1fd032ee10
"target: move code for CDB emulation".
There are still clients out there which use these old SCSI-2 commands.
This mainly happens when running VMs with legacy guest systems,
connected via SCSI command pass-through to iSCSI targets. Make them
happy and return status GOOD.
Many real SCSI disks or external iSCSI storage devices still support
these old commands. So let's make LIO backward compatible as well.
This patch adds support for the previously removed SEEK_10 and
additionally the SEEK_6 and REZERO_UNIT commands.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Integrators were using the .nr_irqs field of the machine
descriptor to pre-allocate a number of descriptors at boot. This
is not right: the irq chip implementations should allocate
their descriptors themselves, and as a result the simple
irqdomain code warns about it.
Get rid of this by just deleting the .nr_irq field from the
machine descriptors but take care: doing so makes the default
implementation hog the first 16 IRQ numbers, so these cannot
be used by the still static IRQ number assignments in the
ATAG boot case. So for these, bump the IRQ numbers to begin
at 64 and upward.
Introduce an offset to offset all IRQ numbers if need be,
though we don't expect to do that again as device tree comes
along.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fabric drivers currently expect to internally release se_cmd in the event
of a TMR failure during target_submit_tmr(), which means the immediate call
to transport_generic_free_cmd() after TFO->queue_tm_rsp() from within
target_complete_tmr_failure() workqueue context is wrong.
This is done as some fabrics expect TMR operations to be acknowledged
before releasing the descriptor, so the assumption that core is releasing
se_cmd associated TMR memory is incorrect. This fixes a OOPs where
transport_generic_free_cmd() was being called more than once.
This bug was originally observed with tcm_qla2xxx fabric ports.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This switches the FPGA IRQ driver over to using the simple IRQ
domain. We can then use the same codepath for this in the
DT and non-DT cases.
To be able to use quicker irq_find_mapping() in the handlers
we first call irq_create_mapping() on all the valid HW IRQ
numbers so that descriptors will be created for them in the
DT case where a linear domain will be the outcome of the
call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this file includes prototypes that doesnt have a function for them,
and some macros which are never used, remove them instead
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
there are macros and functions that are not used, or their
function is missing, so remove them.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Montgomery Multiply, Montgomery Square, and Multiple-Precision
Multiply instructions work by loading a combination of the floating
point and multiple register windows worth of integer registers
with the inputs.
These values are 64-bit. But for 32-bit userland processes we only
save the low 32-bits of each integer register during a register spill.
This is because the register window save area is in the user stack and
has a fixed layout.
Therefore, the only way to use these instruction in 32-bit mode is to
perform the following sequence:
1) Load the top-32bits of a choosen integer register with a sentinel,
say "-1". This will be in the outer-most register window.
The idea is that we're trying to see if the outer-most register
window gets spilled, and thus the 64-bit values were truncated.
2) Load all the inputs for the montmul/montsqr/mpmul instruction,
down to the inner-most register window.
3) Execute the opcode.
4) Traverse back up to the outer-most register window.
5) Check the sentinel, if it's still "-1" store the results.
Otherwise retry the entire sequence.
This retry is extremely troublesome. If you're just unlucky and an
interrupt or other trap happens, it'll push that outer-most window to
the stack and clear the sentinel when we restore it.
We could retry forever and never make forward progress if interrupts
arrive at a fast enough rate (consider perf events as one example).
So we have do limited retries and fallback to software which is
extremely non-deterministic.
Luckily it's very straightforward to provide a mechanism to let
32-bit applications use a 64-bit stack. Stacks in 64-bit mode are
biased by 2047 bytes, which means that the lowest bit is set in the
actual %sp register value.
So if we see bit zero set in a 32-bit application's stack we treat
it like a 64-bit stack.
Runtime detection of such a facility is tricky, and cumbersome at
best. For example, just trying to use a biased stack and seeing if it
works is hard to recover from (the signal handler will need to use an
alt stack, plus something along the lines of longjmp). Therefore, we
add a system call to report a bitmask of arch specific features like
this in a cheap and less hairy way.
With help from Andy Polyakov.
Signed-off-by: David S. Miller <davem@davemloft.net>
The rbd_device structure has an embedded rbd_options structure.
Such a structure is needed to work with the generic ceph argument
parsing code, but there's no need to keep it around once argument
parsing is done.
Use a local variable to hold the rbd options used in parsing in
rbd_get_client(), and just transfer its content (it's just a
read_only flag) into the field in the rbd_mapping sub-structure
that requires that information.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
The aim of this patch is to make what's going on rbd_merge_bvec() a
bit more obvious than it was before. This was an issue when a
recent btrfs bug led us to question whether the merge function was
working correctly.
Use "obj" rather than "chunk" to indicate the units whose boundaries
we care about we call (rados) "objects".
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Change RBD_MAX_SNAP_NAME_LEN to be based on NAME_MAX. That is a
practical limit for the length of a snapshot name (based on the
presence of a directory using the name under /sys/bus/rbd to
represent the snapshot).
The /sys entry is created by prefixing it with "snap_"; define that
prefix symbolically, and take its length into account in defining
the snapshot name length limit.
Enforce the limit in rbd_add_parse_args(). Also delete a dout()
call in that function that was not meant to be committed.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This adds a verification that an rbd image's object order is
within the upper and lower bounds supported by this implementation.
It must be at least 9 (SECTOR_SHIFT), because the Linux bio system
assumes that minimum granularity.
It also must be less than 32 (at the moment anyway) because there
exist spots in the code that store the size of a "segment" (object
backing an rbd image) in a signed int variable, which can be 32 bits
including the sign. We should be able to relax this limit once
we've verified the code uses 64-bit types where needed.
Note that the CLI tool already limits the order to the range 12-25.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The two calls to rbd_do_op() from rbd_rq_fn() differ only in the
value passed for the snapshot id and the snapshot context.
For reads the snapshot always comes from the mapping, and for writes
the snapshot id is always CEPH_NOSNAP.
The snapshot context is always null for reads. For writes, the
snapshot context always comes from the rbd header, but it is
acquired under protection of header semaphore and could change
thereafter, so we can't simply use what's available inside
rbd_do_op().
Eliminate the snapid parameter from rbd_do_op(), and set it
based on the I/O direction inside that function instead. Always
pass the snapshot context acquired in the caller, but reset it
to a null pointer inside rbd_do_op() if the operation is a read.
As a result, there is no difference in the read and write calls
to rbd_do_op() made in rbd_rq_fn(), so just call it unconditionally.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only callers of rbd_do_op() are in rbd_rq_fn(), where call one
is used for writes and the other used for reads. The request passed
to rbd_do_op() already encodes the I/O direction, and that
information can be used inside the function to set the opcode and
flags value (rather than passing them in as arguments).
So get rid of the opcode and flags arguments to rbd_do_op().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Both rbd_req_read() and rbd_req_write() are simple wrapper routines
for rbd_do_op(), and each is only called once. Replace each wrapper
call with a direct call to rbd_do_op(), and get rid of the wrapper
functions.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The name of the "read-only" mapping option was inadvertently changed
in this commit:
f84344f3 rbd: separate mapping info in rbd_dev
Revert that hunk to return it to what it should be.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When rbd_dev_probe() calls rbd_dev_image_id() it expects to get
a 0 return code if successful, but it is getting a positive value.
The reason is that rbd_dev_image_id() returns the value it gets from
rbd_req_sync_exec(), which returns the number of bytes read in as a
result of the request. (This ultimately comes from
ceph_copy_from_page_vector() in rbd_req_sync_op()).
Force the return value to 0 when successful in rbd_dev_image_id().
Do the same in rbd_dev_v2_object_prefix().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
In rbd_dev_id_put(), there's a loop that's intended to determine
the maximum device id in use. But it isn't doing that at all,
the effect of how it's written is to simply use the just-put id
number, which ignores whole purpose of this function.
Fix the bug.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
Pull slave-dmaengine fixes from Vinod Koul:
"Three fixes for slave dmanegine.
Two are for typo omissions in sifr dmaengine driver and the last one
is for the imx driver fixing a missing unlock"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sirf: fix a typo in moving running dma_desc to active queue
dmaengine: sirf: fix a typo in dma_prep_interleaved
dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()
set_request_path_attr() checks for NULL ptr before calling strlen()
This fixes http://tracker.newdream.net/issues/3404
Signed-off-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The ceph_on_in_msg_alloc() method calls the ->alloc_msg() helper which
may return NULL. It also drops con->mutex while it allocates a message,
which means that the connection state may change (e.g., get closed). If
that happens, we clean up and bail out. Avoid calling ceph_msg_put() on
a NULL return value and triggering a crash.
This was observed when an ->alloc_msg() call races with a timeout that
resends a zillion messages and resets the connection, and ->alloc_msg()
returns NULL (because the request was resent to another target).
Fixes http://tracker.newdream.net/issues/3342
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Call to d_find_alias() needs a corresponding dput()
This fixes http://tracker.newdream.net/issues/3271
Signed-off-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Resolve the following sparse warnings:
arch/arm/mach-omap1/usb.c:304:12: warning: symbol 'omap1_usb0_init' was not declared. Should it be static?
arch/arm/mach-omap1/usb.c:412:12: warning: symbol 'omap1_usb1_init' was not declared. Should it be static?
arch/arm/mach-omap1/usb.c:478:12: warning: symbol 'omap1_usb2_init' was not declared. Should it be static?
by declaring those functions as static.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: this was missed with plat/usb.h removal]
Signed-off-by: Tony Lindgren <tony@atomide.com>
try_to_freeze_tasks() and cgroup_freezer rely on scheduler locks
to ensure that a task doing STOPPED/TRACED -> RUNNING transition
can't escape freezing. This mostly works, but ptrace_stop() does
not necessarily call schedule(), it can change task->state back to
RUNNING and check freezing() without any lock/barrier in between.
We could add the necessary barrier, but this patch changes
ptrace_stop() and do_signal_stop() to use freezable_schedule().
This fixes the race, freezer_count() and freezer_should_skip()
carefully avoid the race.
And this simplifies the code, try_to_freeze_tasks/update_if_frozen
no longer need to use task_is_stopped_or_traced() checks with the
non trivial assumptions. We can rely on the mechanism which was
specially designed to mark the sleeping task as "frozen enough".
v2: As Tejun pointed out, we can also change get_signal_to_deliver()
and move try_to_freeze() up before 'relock' label.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
* Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
* Fix for smp_processor_id() usage in preemptible code in powernow-k8 from
Andreas Herrmann.
* Fix for a suspend-related memory leak in cpufreq stats from Xiaobing Tu.
* Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD
in flush_old_exec() from Oleg Nesterov.
* acpi_processor_notify() fix from Alan Cox.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8Tcc
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
The code to allow EAPOL frames even when the station
isn't yet marked associated needs to check that the
incoming frame is long enough and due to paged RX it
also can't assume skb->data contains the right data,
it must use skb_copy_bits(). Fix this to avoid using
data that doesn't really exist.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to pskb_may_pull() checking the skb length, all
non-management frames are checked on input whether
their 802.11 header is fully present. Also add that
check for management frames and remove a check that
is now duplicate. This prevents accessing skb data
beyond the frame end.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh header can have address extension by a 4th
or a 5th and 6th address, but never both. Drop such
frames in 802.11 -> 802.3 conversion along with any
frames that have the wrong extension.
Cc: stable@vger.kernel.org
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'ssid' field of the cfg80211_ibss_params is a u8 pointer and
its length is likely to be less than IEEE80211_MAX_SSID_LEN most
of the time.
This patch fixes the ssid copy in ieee80211_ibss_join() by using
the SSID length to prevent it from reading beyond the string.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[rewrapped commit message, small rewording]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable base_gfn is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
OMAP cleanup-headers branch. Intended for 3.8 cleanup.
Basic build, boot, and PM test logs are available from here:
http://www.pwsan.com/omap/testlogs/cleanup-headers-compile-fixes-3.8/20121026132711/
Due to underlying problems in v3.7-rc2, several tests fail. These
failures are unrelated to these patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zL/L
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-fixes-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-headers
Several fixes for build failures and sparse warnings in the
OMAP cleanup-headers branch. Intended for 3.8 cleanup.
Basic build, boot, and PM test logs are available from here:
http://www.pwsan.com/omap/testlogs/cleanup-headers-compile-fixes-3.8/20121026132711/
Due to underlying problems in v3.7-rc2, several tests fail. These
failures are unrelated to these patches.
We said we would wait until the 3.6 kernel release to remove these
drivers. So we waited 6 months longer, that should be fine.
If anyone wants them back, it is trivial to revert these, but given that
I don't think they even build anymore, I doubt anyone will want them.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for the target code to change the loop_id or s_id of a
target session in reaction to an FC fabric change. However, the
session structures are stored in tables that are indexed by these two
keys, and if we just change the session structure but leave the
pointers to it in the old places in the table, havoc can ensue. For
example, a new session might come along that should go in the old slot
in the table and overwrite the old session pointer.
To handle this, add a new tgt_ops->update_sess() method that also
updates the "by loop_id" and "by s_id" lookup tables when a session
changes, so that the keys where a session pointer is stored in these
tables always matches the keys in the session structure itself.
(nab: Drop unnecessary double inversion with FCF_CONF_COMP_SUPPORTED
usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says the following about the SCSI name string in
inquiry VPD page 83h:
The SCSI NAME STRING field starts with either:
a) the four UTF-8 characters 'eui.' concatenated with 16, 24, or
32 hexadecimal digits (i.e., the UTF-8 characters 0 through 9
and A through F) for an EUI-64 based identifier (see
7.8.6.5). The first hexadecimal digit shall be the most
significant four bits of the first byte (i.e., most significant
byte) of the EUI-64 based identifier;
b) the four UTF-8 characters 'naa.' concatenated with 16 or 32
hexadecimal digits for an NAA identifier (see 7.8.6.6). The
first hexadecimal digit shall be the most significant four bits
of the first byte (i.e., most significant byte) of the NAA
identifier; or
c) the four UTF-8 characters 'iqn.' concatenated with an iSCSI
Name for an iSCSI-name based identifier (see iSCSI).
However, the .tpg_get_wwn method for tcm_qla2xxx formats the WWN so
the SCSI name string looks like "52:4a:93:7d:24:5f:b2:12,t,0x0001".
This patch corrects the code so that VPD 83h gives a SPC-compliant
SCSI name string like "naa.524a937d245fb212,t,0x0001" while leavig
other uses alone (so configfs will still work with ':' separated WWNs).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>