Currently the timer is armed for 1ms after the first use and is killed
immediately, dropping the forcewake as early as possible. However, for
very frequent operations the forcewake dance has a large impact on
latency and keeping the timer alive until we are idle is preferred. To
achieve this, if we call intel_uncore_forcewake_get whilst the timer is
alive (repeated use), then set a flag to restart the timer on expiry
rather than drop the forcewake usage count. The timer is racy, the
consequence of the race is to expire the timer earlier than is now
desired but does not impact on correct behaviour. The offset the race
slightly, we set the active flag again on intel_uncore_forcewake_put.
The effect should be to reduce the jitter of reacquiring the fw every
1ms on a busy system. However, the cost is to keep the timer alive for
an extra 1ms on a nearly idle system. We chose to incur the jitter
previously to keep the timer off for as much as possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526132209.14640-1-chris@chris-wilson.co.uk
We're currently deleting the GuC logs if the FW fails to load, but those
are still useful to understand why the loading failed. Keeping the
object around allows us to access them after driver load is completed.
v2: keep the object around instead of using kernel memory (chris)
don't store the logs in the gpu_error struct (Chris)
add a check on guc_log_level to avoid snapshotting empty logs
v3: use separate debugfs for error log (Chris)
v4: rebased
v5: clean up obj selection, move err_load inside guc_log, move err_load
cleanup, rename functions (Michal)
v6: move obj back to intel_guc, move functions to intel_uc.c, don't
clear obj on new GuC load, free object only if enable_guc_loading
is set (Michal)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495475428-19295-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Tested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Buffer based command transport can replace MMIO based mechanism.
It may be used to perform host-2-guc and guc-to-host communication.
Portions of this patch are based on work by:
Michel Thierry <michel.thierry@intel.com>
Robert Beckett <robert.beckett@intel.com>
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
v2: use gem_object_pin_map (Chris)
don't use DEBUG_RATELIMITED (Chris)
don't track action stats (Chris)
simplify next fence (Chris)
use READ_ONCE (Chris)
move blob allocation to new function (Chris)
v3: use static owner id (Daniele)
v4: but keep channel initialization generic (Daniele)
and introduce owner_sub_id (Daniele)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-3-michal.wajdeczko@intel.com
In earlier patch 789a625 we were enabling send function only
after successful init. For completeness, we should make sure
that we disable it on fini.
v2: don't group steps by submission flag (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-2-michal.wajdeczko@intel.com
There are some panel that
(1) does not support display backlight enable via AUX
(2) support display backlight adjustment via AUX
(3) support display backlight enable via eDP BL_ENABLE pin
The current driver required that (1) must be support to enable (2).
This patch drops that requirement.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-2-puthik@chromium.org
vlv_display_irq_postinstall() enables the LPE audio interrupts
regardless of whether the LPE audio irq chip has masked/unmasked
them. Also the irqchip masking/unmasking doesn't consider the state
of the display power well or the device, and hence just leads to
dmesg spew when it tries to access the hardware while it's powered
down.
If the current way works, then we don't need to do anything in the
mask/unmask hooks. If it doesn't work, well, then we'd need to properly
track whether the irqchip has masked/unmasked the interrupts when
we enable display interrupts. And the mask/unmask hooks would need
to check whether display interrupts are even enabled before frobbing
with he registers.
So let's just assume the current way works and neuter the mask/unmask
hooks. Also clean up vlv_display_irq_postinstall() a bit and stop
it from trying to unmask/enable the LPE C interrupt on VLV since it
doesn't exist.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-4-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit ebf5f92147)
Reference: http://mid.mail-archive.com/874cf6d3-4e45-d4cf-e662-eb972490d2ce@redhat.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Drop legacy drm_for_each_connector() in favor of the race-free
drm_for_each_connector_iter().
v2: add missing drm_connector_list_iter_end(Daniel Vetter)
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170512164100.7649-1-gustavo@padovan.org
Drop legacy drm_for_each_connector() in favor of the race-free
drm_for_each_connector_iter().
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511191049.28944-4-gustavo@padovan.org
Drop legacy drm_for_each_connector() in favor of the race-free
drm_for_each_connector_iter()
Cc: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170515134330.3275-1-gustavo@padovan.org
A bunch of bug fixes:
- Fix display flickering on some chips at high refresh rates
- suspend/resume fix
- hotplug fix
- a couple of segfault fixes for certain cases
* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
We depend on intel_iommu_gfx_mapped for various workarounds, but that is
only available under an #ifdef CONFIG_INTEL_IOMMU. Refactor all the
cut-and-paste ifdefs to a common routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525121612.2190-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
As only GGTT vma may be permanently pinned and are always at the head of
the object's vma list, as soon as we seen a ppGTT vma we can stop
searching for any_vma_pinned().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525072528.11185-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
BXT has a H/W issue with IOMMU which can lead to system hangs when
Aperture accesses are queued within the GAM behind GTT Accesses.
This patch avoids the condition by wrapping all GTT updates in stop_machine
and using a flushing read prior to restarting the machine.
The stop_machine guarantees no new Aperture accesses can begin while
the PTE writes are being emmitted. The flushing read ensures that
any following Aperture accesses cannot begin until the PTE writes
have been cleared out of the GAM's fifo.
Only FOLLOWING Aperture accesses need to be separated from in flight
PTE updates. PTE Writes may follow tightly behind already in flight
Aperture accesses, so no flushing read is required at the start of
a PTE update sequence.
This issue was reproduced by running
igt/gem_readwrite and
igt/gem_render_copy
simultaneously from different processes, each in a tight loop,
with INTEL_IOMMU enabled.
This patch was originally published as:
drm/i915: Serialize GTT Updates on BXT
v2: Move bxt/iommu detection into static function
Remove #ifdef CONFIG_INTEL_IOMMU protection
Make function names more reflective of purpose
Move flushing read into static function
v3: Tidy up for checkpatch.pl
Testcase: igt/gem_concurrent_blit
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495641251-30022-1-git-send-email-jon.bloomfield@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Same as the previous patch, but for pageflipping now. This also lets us
clear up the copy paste for vblank/vline IRQs.
Changes since v1:
- Preserve the order all registers are written back
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as the previous patch, but now for handling HDMI audio interrupts.
Changes since v1:
- Preserve the order we write back all registers
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code here is really, really bad. A huge amount of it looks
to be copy pasted, it has some weird hatred of arrays and code sharing,
switch cases everywhere for things that really don't need them, and it
makes the file seem immensely more complex then it actually is. This is
a pain for maintanence, and is vulnerable to more weird irq handling
bugs.
So, let's start cleaning this up a bit. Modify all of the IRQ handlers
for evergreen/si so that they just use for loops. As well, we add a
helper function radeon_irq_kms_set_irq_n_enabled(), whose purpose is
just to update the state of registers that enable/disable interrupts
while printing any changes to the set of enabled interrupts to the
kernel log.
Note in this commit, since vblank/vline irq acking is intertwined with
page flip irq acking, we can't cut out all of the copy paste in
evergreen/si_irq_ack() just yet.
Changes since v1:
- Preserve order we write back all registers
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KIQ is the Kernel Interface Queue for managing the MEC. Rather than setting
up rings via direct MMIO of ring registers, the rings are configured via
special packets sent to the KIQ. The allows the MEC to better manage shared
resources and certain power events. It also reduces the code paths in the
driver to support and is required for MEC powergating.
v2: drop gfx_v9_0_cp_compute_fini() as well
v3: rebase on latest changes derived from gfx8, add unmap queues on
hw_fini
v4: fix copy/paste typo in error message (Rex)
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to reset the wptr and clear the rings. The UNMAP_QUEUES
packet writes the current MQD state back the MQD on suspend,
so there is no need to reset it as well.
v2: fix from gfx8 (Rex)
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Acked-by: monk liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the KCQ setup. This way we only have to wait once for the
entire MEC.
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than waiting for each queue.
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: monk liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
One for KIQ and one for the KCQ. This simplifies the logic and
allows for future optimizations.
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's stored in LE format.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sets floors for various clocks depending on current
requirements.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the new clock type to the gfx arbitor so we can determine
the proper clock floors for it.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New clock type on RV.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print the failed msg when it fails.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: bump the DRM version
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If you initiate a read that is out of the VRAM address space return
ENXIO instead of 0.
Reads that begin below that point will read upto the VRAM limit as
before.
Cc: stable@vger.kernel.org
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If AMDGPU supports CIK, add a module parameter to control CIK
support in radeon. It's off by default in radeon, while it will be
on by default in AMDGPU.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop the function gmc_v6_0_init_compute_vmid() since it wasn't
implemented and commented out.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up coding style in gfx_v6_0_write_harvested_raster_configs()
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That line got missed during the merge.
v2: fix vcn_v1_0_enc_ring_emit_vm_flush as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>