In the current code, msg->data is set as sg_virt(&sg[i]) + start - offset
and msg->data_end relative to it as msg->data + bytes. Using iterator i
to point to the updated starting scatterlist element holds true for some
cases, however not for all where we'd end up pointing out of bounds. It
is /correct/ for these ones:
1) When first finding the starting scatterlist element (sge) where we
find that the page is already privately owned by the msg and where
the requested bytes and headroom fit into the sge's length.
However, it's /incorrect/ for the following ones:
2) After we made the requested area private and updated the newly allocated
page into first_sg slot of the scatterlist ring; when we find that no
shift repair of the ring is needed where we bail out updating msg->data
and msg->data_end. At that point i will point to last_sg, which in this
case is the next elem of first_sg in the ring. The sge at that point
might as well be invalid (e.g. i == msg->sg_end), which we use for
setting the range of sg_virt(&sg[i]). The correct one would have been
first_sg.
3) Similar as in 2) but when we find that a shift repair of the ring is
needed. In this case we fix up all sges and stop once we've reached the
end. In this case i will point to will point to the new msg->sg_end,
and the sge at that point will be invalid. Again here the requested
range sits in first_sg.
Fixes: 015632bb30 ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull NVMe fixes from Christoph.
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: free workqueue object if module init fails
nvme-fcloop: Fix dropped LS's to removed target port
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
Like d88b6d04: "cdrom: information leak in cdrom_ioctl_media_changed()"
There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a HW quirk in BD71837. The shutdown sequence timings for
bucks/LDOs which are enabled via register interface are changed.
At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
beginning of shut-down sequence. This causes LDO5/6 voltage
monitoring to detect under voltage and force PMIC to emergency
state instead of poweroff. Disable voltage monitoring for LDO5 and
LDO6 at probe to avoid this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add of_get_compatible_child() helper that can be used to lookup
compatible child nodes.
Several drivers currently use of_find_compatible_node() to lookup child
nodes while failing to notice that the of_find_ functions search the
entire tree depth-first (from a given start node) and therefore can
match unrelated nodes. The fact that these functions also drop a
reference to the node they start searching from (e.g. the parent node)
is typically also overlooked, something which can lead to use-after-free
bugs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
If dwapb_gpio_add_port() fails in dwapb_gpio_probe(),
gpio->clk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we are being configured via pdata we don't necessarily have
any gpio mappings being configured that way so pdata->gpio_config
could be NULL.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a203728ac6 ("pinctrl: core: Return selector to the pinctrl
driver") and commit f913cfce4e ("pinctrl: pinmux: Return selector to
the pinctrl driver") modified the return values of
pinctrl_generic_add_group() and pinmux_generic_add_function()
respectively, but did so without updating their callers. This broke the
pinctrl-ingenic driver, which treats non-zero return values from these
functions as errors & fails to probe. For example on a MIPS Ci20:
pinctrl-ingenic 10010000.pin-controller: Failed to register group uart0-hwflow
pinctrl-ingenic: probe of 10010000.pin-controller failed with error 1
Without the pinctrl driver probed, other drivers go on to fail to probe
too & the system is unusable.
Fix this by modifying the error checks to treat only negative values as
errors, matching the commits that introduced the breakage & similar
changes made to other drivers.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a203728ac6 ("pinctrl: core: Return selector to the pinctrl driver")
Fixes: f913cfce4e ("pinctrl: pinmux: Return selector to the pinctrl driver")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GpioInt ACPI event handlers may see there IRQ triggered immediately
after requesting the IRQ (esp. level triggered ones). This means that they
may run before any other (builtin) drivers have had a chance to register
their OpRegion handlers, leading to errors like this:
[ 1.133274] ACPI Error: No handler for Region [PMOP] ((____ptrval____)) [UserDefinedRegion] (20180531/evregion-132)
[ 1.133286] ACPI Error: Region UserDefinedRegion (ID=141) has no handler (20180531/exfldio-265)
[ 1.133297] ACPI Error: Method parse/execution failed \_SB.GPO2._L01, AE_NOT_EXIST (20180531/psparse-516)
We already defer the manual initial trigger of edge triggered interrupts
by running it from a late_initcall handler, this commit replaces this with
deferring the entire acpi_gpiochip_request_interrupts() call till then,
fixing the problem of some OpRegions not being registered yet.
Note that this removes the need to have a list of edge triggered handlers
which need to run, since the entire acpi_gpiochip_request_interrupts() call
is now delayed, acpi_gpiochip_request_interrupt() can call these directly
now.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit ca876c7483
("gpiolib-acpi: make sure we trigger edge events at least once on boot")
added a initial value check for pin which is about to be locked as IRQ.
Unfortunately, not all GPIO drivers can do that atomically. Thus,
switch to cansleep version of the call. Otherwise we have a warning:
...
WARNING: CPU: 2 PID: 1408 at drivers/gpio/gpiolib.c:2883 gpiod_get_value+0x46/0x50
...
RIP: 0010:gpiod_get_value+0x46/0x50
...
The change tested on Intel Broxton with Whiskey Cove PMIC GPIO controller.
Fixes: ca876c7483 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using a private template is problematic:
1. We can't assign both a zone and a timeout policy
(zone assigns a conntrack template, so we hit problem 1)
2. Using a template needs to take care of ct refcount, else we'll
eventually free the private template due to ->use underflow.
This patch reworks template policy to instead work with existing conntrack.
As long as such conntrack has not yet been placed into the hash table
(unconfirmed) we can still add the timeout extension.
The only caveat is that we now need to update/correct ct->timeout to
reflect the initial/new state, otherwise the conntrack entry retains the
default 'new' timeout.
Side effect of this change is that setting the policy must
now occur from chains that are evaluated *after* the conntrack lookup
has taken place.
No released kernel contains the timeout policy feature yet, so this change
should be ok.
Changes since v2:
- don't handle 'ct is confirmed case'
- after previous patch, no need to special-case tcp/dccp/sctp timeout
anymore
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
tcp, sctp and dccp trackers re-use the userspace ctnetlink states
to index their timeout arrays, which means timeout[0] is never
used. Copy the 'new' state (syn-sent, dccp-request, ..) to 0 as well
so external users can simply read it off timeouts[0] without need to
differentiate dccp/sctp/tcp and udp/icmp/gre/generic.
The alternative is to map all array accesses to 'i - 1', but that
is a much more intrusive change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
An unfortunate consequence of having a strong typing for the input
values to the SMC call is that it also affects the type of the
return values, limiting r0 to 32 bits and r{1,2,3} to whatever
was passed as an input.
Let's turn everything into "unsigned long", which satisfies the
requirements of both architectures, and allows for the full
range of return values.
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix mismatch between SVE registers (Z) and FPSIMD register (V)
- Don't prefix the path for [3] with Linux to stay consistent with
[1] and [2].
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building building AMSDU from non-linear SKB, we hit a
kernel panic when trying to push the padding to the tail.
Instead, put the padding at the head of the next subframe.
This also fixes the A-MSDU subframes to not have the padding
accounted in the length field and not have pad at all for
the last subframe, both required by the spec.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_direction_input()
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt controller hardware in this pin controller has two status
enable bits. The first "normal" status enable bit enables or disables
the summary interrupt line being raised when a gpio interrupt triggers
and the "raw" status enable bit allows or prevents the hardware from
latching an interrupt into the status register for a gpio interrupt.
Currently we just toggle the "normal" status enable bit in the mask and
unmask ops so that the summary irq interrupt going to the CPU's
interrupt controller doesn't trigger for the masked gpio interrupt.
For a level triggered interrupt, the flow would be as follows: the pin
controller sees the interrupt, latches the status into the status
register, raises the summary irq to the CPU, summary irq handler runs
and calls handle_level_irq(), handle_level_irq() masks and acks the gpio
interrupt, the interrupt handler runs, and finally unmask the interrupt.
When the interrupt handler completes, we expect that the interrupt line
level will go back to the deasserted state so the genirq code can unmask
the interrupt without it triggering again.
If we only mask the interrupt by clearing the "normal" status enable bit
then we'll ack the interrupt but it will continue to show up as pending
in the status register because the raw status bit is enabled, the
hardware hasn't deasserted the line, and thus the asserted state latches
into the status register again. When the hardware deasserts the
interrupt the pin controller still thinks there is a pending unserviced
level interrupt because it latched it earlier. This behavior causes
software to see an extra interrupt for level type interrupts each time
the interrupt is handled.
Let's fix this by clearing the raw status enable bit for level type
interrupts so that the hardware stops latching the status of the
interrupt after we ack it. We don't do this for edge type interrupts
because it seems that toggling the raw status enable bit for edge type
interrupts causes spurious edge interrupts.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Reported-by: Junki Kato <junki.kato.xk@renesas.com>
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Junki Kato <junki.kato.xk@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no deallocation of fotg210->ep[i] elements, allocated at
fotg210_udc_probe.
The patch adds deallocation of fotg210->ep array elements and simplifies
error path of fotg210_udc_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding. It
introduced regressions into both the dummy-hcd and net2280 drivers.
The problem in dummy-hcd was fixed by commit 7dbd8f4cab ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.
This patch largely is a reversion of the relevant parts of
f16443a034. It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.
Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off. Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
Reported-by: D. Ziesche <dziesche@zes.com>
Tested-by: D. Ziesche <dziesche@zes.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db865 ("usb: dwc3: of-simple: reset host controller at suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
While recently going over bpf_msg_pull_data(), I noticed three
issues which are fixed in here:
1) When we attempt to find the first scatterlist element (sge)
for the start offset, we add len to the offset before we check
for start < offset + len, whereas it should come after when
we iterate to the next sge to accumulate the offsets. For
example, given a start offset of 12 with a sge length of 8
for the first sge in the list would lead us to determine this
sge as the first sge thinking it covers first 16 bytes where
start is located, whereas start sits in subsequent sges so
we would end up pulling in the wrong data.
2) After figuring out the starting sge, we have a short-cut test
in !msg->sg_copy[i] && bytes <= len. This checks whether it's
not needed to make the page at the sge private where we can
just exit by updating msg->data and msg->data_end. However,
the length test is not fully correct. bytes <= len checks
whether the requested bytes (end - start offsets) fit into the
sge's length. The part that is missing is that start must not
be sge length aligned. Meaning, the start offset into the sge
needs to be accounted as well on top of the requested bytes
as otherwise we can access the sge out of bounds. For example
the sge could have length of 8, our requested bytes could have
length of 8, but at a start offset of 4, so we also would need
to pull in 4 bytes of the next sge, when we jump to the out
label we do set msg->data to sg_virt(&sg[i]) + start - offset
and msg->data_end to msg->data + bytes which would be oob.
3) The subsequent bytes < copy test for finding the last sge has
the same issue as in point 2) but also it tests for less than
rather than less or equal to. Meaning if the sge length is of
8 and requested bytes of 8 while having the start aligned with
the sge, we would unnecessarily go and pull in the next sge as
well to make it private.
Fixes: 015632bb30 ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull thermal fixes from Eduardo Valentin:
"Minor fixes to OF thermal, qoriq, and rcar drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: of-thermal: disable passive polling when thermal zone is disabled
thermal: rcar_gen3_thermal: convert to SPDX identifiers
thermal: rcar_thermal: convert to SPDX identifiers
thermal: qoriq: Switch to SPDX identifier
thermal: qoriq: Simplify the 'site' variable assignment
thermal: qoriq: Use devm_thermal_zone_of_sensor_register()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count,
GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, currently, there is a bug during the allocation:
sizeof(npcm7xx_clk_data) should be sizeof(*npcm7xx_clk_data)
Fix this bug by using struct_size() in kzalloc()
This issue was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Variable save_pud is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'save_pud' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Export device state to sysfs to allow for easier get device state.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Thanks to Christoph Hellwig for pointing out a cleaner way to do this,
as my approach was quite ugly.
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
As of commit fd1102f0aa ("mm: mmu_notifier fix for tlb_end_vma"),
asm-generic/tlb.h now calls tlb_flush() from a static inline function,
so we need to make sure that it's declared before #including the
asm-generic header in the arch header.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fd1102f0aa ("mm: mmu_notifier fix for tlb_end_vma")
Signed-off-by: Will Deacon <will.deacon@arm.com>
[groeck: Use forward declaration instead of moving inline function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
I managed to miss one of Rob's code reviews on the mailing list
<http://lists.infradead.org/pipermail/linux-riscv/2018-August/001139.html>.
The patch has already been merged, so I'm submitting a fixup.
Sorry!
Fixes: b67bc7cb40 ("dt-bindings: interrupt-controller: RISC-V local interrupt controller")
Cc: Rob Herring <robh@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Karsten Merker <merker@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch fixes the dspi_eoq_write function used by the
ColdFire mcf5441x family. The 16 bit cmd part must be re-set at
each data transfer.
Also, now that fifo_size variables are used for eoq_read/write,
a proper fifo size must be set (16 slots for the ColdFire dspi
module version).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We use kzalloc to allocate the write_buf that we use for
i2c transfer on hdcp write. But it seems that we are forgetting
to free the memory that is not needed after i2c transfer is
completed.
Reported-by: Brian J Wood <brian.j.wood@intel.com>
Fixes: 2320175feb ("drm/i915: Implement HDCP for HDMI")
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180823205136.31310-1-rodrigo.vivi@intel.com
(cherry picked from commit 62d3a8deaa)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The workaround was supposed to look at the plane destination
coordinates. Currently it's looking at some mixture of src
and dst coordinates that doesn't make sense. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719182214.4323-2-ville.syrjala@linux.intel.com
Fixes: 394676f05b (drm/i915: Add WA for planes ending close to left screen edge)
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit b1f1c2c11f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:
WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
couldn't get idr
Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.
Fixes: 1a4327fbf4 ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed range in safeload conditional to allow safeload to up to 20 bytes,
without a lower limit.
Signed-off-by: Danny Smith <dannys@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier.
This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform.
The scripts at https://github.com/thesofproject/acpi-scripts can be
used to add the ACPI initrd overlays.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step of DAC/ADC volume scale changes from 0.375dB to 0.75dB
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fix the VMC page fault when the running sequence is as below:
1.amdgpu_gem_create_ioctl
2.ttm_bo_swapout->amdgpu_vm_bo_invalidate, as not called
amdgpu_vm_bo_base_init, so won't called
list_add_tail(&base->bo_list, &bo->va). Even the bo was evicted,
it won't set the bo_base->moved.
3.drm_gem_open_ioctl->amdgpu_vm_bo_base_init, here only called
list_move_tail(&base->vm_status, &vm->evicted), but not set the
bo_base->moved.
4.amdgpu_vm_bo_map->amdgpu_vm_bo_insert_map, as the bo_base->moved is
not set true, the function amdgpu_vm_bo_insert_map will call
list_move(&bo_va->base.vm_status, &vm->moved)
5.amdgpu_cs_ioctl won't validate the swapout bo, as it is only in the
moved list, not in the evict list. So VMC page fault occurs.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae6 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix wrong mode for dts file added by commit bb3e3fbbac
("ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED
based on TI AM335x").
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 156c3df8d4.
Since XArray and the new mount apis aren't merged in 4.19-rc1
merge window, the BROKEN mark can be reverted directly without
any problems.
Fixes: 156c3df8d4 ("staging: erofs: disable compiling temporarile")
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dynamically allocted collection stack does not get freed in
all situations. Make sure to also free the collection stack when
using the parser in hid_open_report().
Fixes: 08a8a7cf14 ("HID: core: do not upper bound the collection stack")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure to free the custom input node name on disconnect.
Cc: stable@vger.kernel.org # v4.18+
Fixes: c554bb0455 ("HID: input: append a suffix matching the application")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB device
Vendor 05ac (Apple)
Device 026c (Magic Keyboard with Numeric Keypad)
Bluetooth devices
Vendor 004c (Apple)
Device 0267 (Magic Keyboard)
Device 026c (Magic Keyboard with Numeric Keypad)
Support already exists for the Magic Keyboard over USB connection.
Add support for the Magic Keyboard over Bluetooth connection, and for
the Magic Keyboard with Numeric Keypad over Bluetooth and USB
connection.
Signed-off-by: Sean O'Brien <seobrien@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
