Due to the way Machine Check Exceptions work on X86 hyperthreads it's
required to boot up _all_ logical cores at least once in order to set the
CR4.MCE bit.
So instead of ignoring the sibling threads right away, let them boot up
once so they can configure themselves. After they came out of the initial
boot stage check whether its a "secondary" sibling and cancel the operation
which puts the CPU back into offline state.
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Dave Hansen reported, that it's outright dangerous to keep SMT siblings
disabled completely so they are stuck in the BIOS and wait for SIPI.
The reason is that Machine Check Exceptions are broadcasted to siblings and
the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
reboots the machine. The MCE chapter in the SDM contains the following
blurb:
Because the logical processors within a physical package are tightly
coupled with respect to shared hardware resources, both logical
processors are notified of machine check errors that occur within a
given physical processor. If machine-check exceptions are enabled when
a fatal error is reported, all the logical processors within a physical
package are dispatched to the machine-check exception handler. If
machine-check exceptions are disabled, the logical processors enter the
shutdown state and assert the IERR# signal. When enabling machine-check
exceptions, the MCE flag in control register CR4 should be set for each
logical processor.
Reverting the commit which ignores siblings at enumeration time solves only
half of the problem. The core cpuhotplug logic needs to be adjusted as
well.
This thoughtful engineered mechanism also turns the boot process on all
Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
before the secondary CPUs are brought up. Depending on the number of
physical cores the window in which this situation can happen is smaller or
larger. On a HSW-EX it's about 750ms:
MCE is enabled on the boot CPU:
[ 0.244017] mce: CPU supports 22 MCE banks
The corresponding sibling #72 boots:
[ 1.008005] .... node #0, CPUs: #72
That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
between these two points the machine is going to shutdown. At least it's a
known safe state.
It's obvious that the early boot can be hit by an MCE as well and then runs
into the same situation because MCEs are not yet enabled on the boot CPU.
But after enabling them on the boot CPU, it does not make any sense to
prevent the kernel from recovering.
Adjust the nosmt kernel parameter documentation as well.
Reverts: 2207def700 ("x86/apic: Ignore secondary threads if nosmt=force")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Replace strncpy which has been used to copy a substring into buf
without NUL-termination with memcpy to avoid the following gcc 8
warnings:
arch/s390/tools/gen_opcode_table.c: In function ‘add_to_group.isra.4’:
arch/s390/tools/gen_opcode_table.c:260:2: warning: ‘strncpy’
output may be truncated copying 2 bytes from a string of length 19
[-Wstringop-truncation]
strncpy(group->opcode, insn->opcode, 2);
In function ‘print_opcode_table’,
inlined from ‘main’ at arch/s390/tools/gen_opcode_table.c:333:2:
arch/s390/tools/gen_opcode_table.c:286:4: warning: ‘strncpy’
output may be truncated copying 2 bytes from a string of length 19
[-Wstringop-truncation]
strncpy(opcode, insn->opcode, 2);
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since the plain vmlinux ELF file no longer carries all necessary parts
for starting up (like the entry point and decompressor), add a check
which would block boot process and encourage users to use bzImage or
arch/s390/boot/compressed/vmlinux instead.
The check relies on s390 linux entry point ABI definition, which is only
present in bzImage and arch/s390/boot/compressed/vmlinux.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The following gcc warning is issued for strncpy which is used to
deliberately avoid string NUL-termination. Reuse memcpy to avoid the
warning.
inlined from 'monwrite_diag' at drivers/s390/char/monwriter.c:64:2:
./include/linux/string.h:246:9: warning: '__builtin_strncpy' output
truncated before terminating nul copying 7 bytes from a string of the
same length [-Wstringop-truncation]
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace strncpy which is used to deliberately avoid string NUL-termination
with memcpy. This allows to get rid of gcc 8 stringop-truncation warning:
inlined from 'ext_to_int_kekl' at drivers/s390/char/tape_3590.c:123:2:
./include/linux/string.h:246:9: warning: '__builtin_strncpy'
output may be truncated copying 64 bytes from a string of length 64
[-Wstringop-truncation]
Also replaces "for" loop on memset.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use strlcpy to make sure strings are NUL-terminated. Fixes the following
gcc 8 warning:
inlined from 'register_tape_dev' at drivers/s390/char/tape_class.c:57:2:
./include/linux/string.h:246:9: warning: '__builtin_strncpy' specified
bound 32 equals destination size [-Wstringop-truncation]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Aligning struct lowcore to double page size allows to get rid of this
gcc warning:
In file included from ./arch/s390/include/asm/setup.h:56,
from ./arch/s390/include/asm/page.h:36,
from ./arch/s390/include/asm/user.h:11,
from ./include/linux/user.h:1,
from ./include/linux/elfcore.h:5,
from ./include/linux/crash_core.h:6,
from ./include/linux/kexec.h:18,
from arch/s390/purgatory/purgatory.c:10:
./arch/s390/include/asm/lowcore.h:189:1: warning: alignment 1 of 'struct
lowcore' is less than 8 [-Wpacked-not-aligned]
} __packed;
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The following linker construct is problematic with linkers of
binutils < 2.28:
EXCLUDE_FILE (*piggy.o) *(.rodata.*)
from 8f1732fc2a11dc of binutils:
"though the linker accepts this without complaint the
EXCLUDE_FILE part is silently ignored and has no effect."
Silent ignoring of EXCLUDE_FILE construct made .rodata.compressed be
part of .rodata, and in case of .rodata.compressed following some
unaligned data, input_len would also become unaligned.
from arch/s390/boot/compressed/vmlinux.map:
.rodata.compressed
0x0000000000012fea 0x4d57e7 arch/s390/boot/compressed/piggy.o
0x0000000000012fea input_len
0x0000000000012fee input_data
input_len is later used here:
arch/s390/boot/compressed/misc.c:113
__decompress(input_data, input_len, NULL, NULL, output, 0, NULL, error);
asm generated by gcc looks like:
.loc 3 113 0
egfrl %r11,input_len
from what assembler generates invalid (the second operand must be aligned
on a doubleword boundary):
0x00000000000129b4 <+148>: c4 bc 00 00 03 1b lgfrl %r11,0x12fea
hence specification exception is recognized.
To avoid an issue use EXCLUDE_FILE construct which is recognized by
older linkers (since at least binutils-2_11)
*(EXCLUDE_FILE (*piggy.o) .rodata.compressed)
Also ensure that .rodata.compressed is at least doubleword aligned.
Fixes: 89b5202e81 ("s390/decompressor: support uncompressed kernel")
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since the uncompressed image .text section starts at 0x100000 now there
is no need to redefine _text to something else to make perf happy.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid unnecessary rewrite of psw and merge _stext into
startup_continue. This allows to move _stext definition to vmlinux.lds.S,
where _etext is also defined and set _stext to the actual beginning of
.text at 0x100000.
This fixes the problem with setting the last .text page as
not-executable due to vmem_map_init relying on page alinged _stext and
_etext.
Fixes: bd79d66329 ("s390/decompressor: trim the kernel image up to 1M")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Instead of generating uncompressed kernel image starting at 0, filling
first mb with zeros (with ".org 0x100000") and then trimming it off
from vmlinux.bin before compression, simply generate a kernel image
starting from 0x100000.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since startup code now reserves memory ranges [0, PARMAREA_END] and
[_stext, <end of kernel>] _ehead symbol is not used and could be
cleaned up.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently none of the vmlinux linker script patterns in .text section
match expoline execute-trampolines, and they end up as separate
sections:
.text.__s390_indirect_jump_r1,
.text.__s390x_indirect_jump_r1use_r9,
.text.__s390x_indirect_branch_4_1use_6, ...
Add a pattern to match them all.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
___kcrctab section is not used during the decompressor phase and could be
discarded to save the memory. It is currently generated due to lib/mem.S
usage, which exports few symbols.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There have been identified some places in the zcrypt
device driver where copy_from_user() is called but the
length value is not explicitly checked.
So now some plausibility checks and comments have been
introduced there.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/kernel/perf_regs.c:36:19: warning: array subscript 16 is above
array bounds of 'long unsigned int[16]' [-Warray-bounds]
return regs->gprs[idx];
gcc tries to be smart here and since there is a condition:
if (idx >= PERF_REG_S390_R0 && idx <= PERF_REG_S390_R15)
return regs->gprs[idx];
which covers all possible array subscripts, it gives the warning
for the last function return statement:
return regs->gprs[idx];
which in presence of that condition does not really make sense and
should be replaced with "return 0;"
Also move WARN_ON_ONCE((u32)idx >= PERF_REG_S390_MAX) to the end of the
function.
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/kernel/topology.c:591:3: warning: 'strncpy' output truncated
before terminating nul copying 2 bytes from a string of the same length
[-Wstringop-truncation]
strncpy(buf, topology_is_enabled() ? "1\n" : "0\n", ARRAY_SIZE(buf));
arch/s390/appldata/appldata_base.c:326:3: warning: 'strncpy' output truncated
before terminating nul copying 2 bytes from a string of the same length
[-Wstringop-truncation]
strncpy(buf, ops->active ? "1\n" : "0\n", ARRAY_SIZE(buf));
arch/s390/appldata/appldata_base.c:217:3: warning: 'strncpy' output truncated
before terminating nul copying 2 bytes from a string of the same length
[-Wstringop-truncation]
strncpy(buf, appldata_timer_active ? "1\n" : "0\n", ARRAY_SIZE(buf));
To avoid the warning, just reuse memcpy.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
drivers/s390/block/dasd_alias.c:711:2: warning: 'strncpy' output truncated
before terminating nul copying 4 bytes from a string of the same length
[-Wstringop-truncation]
strncpy((char *) &cqr->magic, "ECKD", 4);
Replace strncpy to int as a buffer with memcpy.
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/mm/extmem.c: In function '__segment_load':
arch/s390/mm/extmem.c:436:2: warning: 'strncat' specified bound 7 equals
source length [-Wstringop-overflow=]
strncat(seg->res_name, " (DCSS)", 7);
What gcc complains about here is the misuse of strncat function, which
in this case does not limit a number of bytes taken from "src", so it is
in the end the same as strcat(seg->res_name, " (DCSS)");
Keeping in mind that a res_name is 15 bytes, strncat in this case
would overflow the buffer and write 0 into alignment byte between the
fields in the struct. To avoid that increasing res_name size to 16,
and reusing strlcat.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce the default values for the number of hardware queues and queue depth
to significantly reduce the memory footprint of a DASD device.
The memory consumption per DASD device reduces from approximately 40MB to
approximately 1.5MB.
This is necessary to build systems with a large number of DASD devices and
a reasonable amount of memory.
Performance measurements showed that good performance results are possible
with the new default values even on systems with lots of CPUs and lots of
alias devices.
Fixes: e443343e50 ("s390/dasd: blk-mq conversion")
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dan Carpenter reported an integer underflow issue in the rtl8188eu driver.
This is also needed for the length (signed integer) in rtl8723bs, as it is
later converted to an unsigned integer and used in a memcpy operation.
Original issue is at https://patchwork.kernel.org/patch/9796371/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Murray McAllister <murray.mcallister@insomniasec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev section was opening curly bracket, but not adding ident, which
resulted in two times "}," after each other with same indentation. Add
ident at the right place fixes this problem.
This formatting issue is not detectable by checkpatch.pl
Signed-off-by: Radek Dostál <radek.dostal@streamunlimited.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Write multiple single line comments as block comments to
follow kernel coding style and improve readability.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of a function should be on the same line as the
definition.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorder the cases of a switch statement to be in ascending order.
Remove unrequired break from default case.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify if else statement to a single function call
by passing the variable.
Suggested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use if(x) and if(!x) instead of comparsion to true/false.
Reported by checkpatch.
Remove unrequired braces from single if else statement.
Add missing space after else: else{ -> else {
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file includes the file rtl819x_HT.h, which has already been included by
the previously included file ieee80211.h
Signed-off-by: John Whitmore <johnfwhitmore@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put data to skb, decrypt with lib80211_crypt_wep, and place back to tx buffer.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whether any of the conditions is true or not, the return variable
is always set to rtw_resume_process(padapter). Replace the if else
construct with a single call to rtw_resume_process(). Also remove
the now unused local variable pwrpriv.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary parentheses as reported by checkpatch.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix line over 80 characters by replacing tab with space.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header rtw_ioctl_rtl.h is not used anywhere.
Running 'grep -r rtw_ioctl_rtl *' from kernel root
directory returns nothing, remove the file.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc 8.1.0 generates the following warnings.
drivers/staging/speakup/kobjects.c: In function 'punc_store':
drivers/staging/speakup/kobjects.c:522:2: warning:
'strncpy' output truncated before terminating nul
copying as many bytes from a string as its length
drivers/staging/speakup/kobjects.c:504:6: note: length computed here
drivers/staging/speakup/kobjects.c: In function 'synth_store':
drivers/staging/speakup/kobjects.c:391:2: warning:
'strncpy' output truncated before terminating nul
copying as many bytes from a string as its length
drivers/staging/speakup/kobjects.c:388:8: note: length computed here
Using strncpy() is indeed less than perfect since the length of data to
be copied has already been determined with strlen(). Replace strncpy()
with memcpy() to address the warning and optimize the code a little.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this was introduced in
commit a519435a96
Author: Christian König <christian.koenig@amd.com>
Date: Tue Oct 20 16:34:16 2015 +0200
dma-buf/fence: add fence_wait_any_timeout function v2
there was a restriction added that this only works if the dma-fence
uses the dma_fence_default_wait hook. Which works for amdgpu, which is
the only caller. Well, until you share some buffers with e.g. i915,
then you get an -EINVAL.
But there's really no reason for this, because all drivers must
support callbacks. The special ->wait hook is only as an optimization;
if the driver needs to create a worker thread for an active callback,
then it can avoid to do that if it knows that there's a process
context available already. So ->wait is just an optimization, just
using the logic in dma_fence_default_wait() should work for all
drivers.
Let's remove this restriction.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503142603.28513-4-daniel.vetter@ffwll.ch
Many drivers have a trivial implementation for ->enable_signaling.
Let's make it optional by assuming that signalling is already
available when the callback isn't present.
v2: Don't do the trick to set the ENABLE_SIGNAL_BIT
unconditionally, it results in an expensive spinlock take for
everyone. Instead just check if the callback is present. Suggested by
Maarten.
Also move misplaced kerneldoc hunk to the right patch.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180504141034.27727-1-daniel.vetter@ffwll.ch
Noticed while I was typing docs. Entirely unused.
v2: Remove reference in @timeline_value_str too. While at it clarify
why timeline_value_str has a fence parameter - we don't have an
explicit timeline structure unfortunately.
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Cc: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503142603.28513-2-daniel.vetter@ffwll.ch
Since the following commit:
cd77849a69 ("objtool: Fix GCC 8 cold subfunction detection for aliased functions")
... if the kernel is built with EXTRA_CFLAGS='-fno-reorder-functions',
objtool can get stuck in an infinite loop.
That flag causes the new GCC 8 cold subfunctions to be placed in .text
instead of .text.unlikely. But it also has an unfortunate quirk: in the
symbol table, the subfunction (e.g., nmi_panic.cold.7) is nested inside
the parent (nmi_panic).
That function overlap confuses objtool, and causes it to get into an
infinite loop in next_insn_same_func(). Here's Allan's description of
the loop:
"Objtool iterates through the instructions in nmi_panic using
next_insn_same_func. Once it reaches the end of nmi_panic at 0x534 it
jumps to 0x528 as that's the start of nmi_panic.cold.7. However, since
the instructions starting at 0x528 are still associated with nmi_panic
objtool will get stuck in a loop, continually jumping back to 0x528
after reaching 0x534."
Fix it by shortening the length of the parent function so that the
functions no longer overlap.
Reported-and-analyzed-by: Allan Xavier <allan.x.xavier@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Allan Xavier <allan.x.xavier@oracle.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/9e704c52bee651129b036be14feda317ae5606ae.1530136978.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some Micron NAND chips (MT29F1G08ABAFAWP-ITE:F) report 00 00 for the
revision number field of the ONFI parameter page. Rather than rejecting
these outright assume ONFI version 1.0 if the revision number is 00 00.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add defines for the ONFI version bits and use them in
nand_flash_detect_onfi().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is called after the ONFI parameter page checksum is verified
and allows us to override the contents of the parameter page.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
>From the controllers point of view this is the same as no or
software only ECC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the NAND flash controller found on NVIDIA
Tegra 2 SoCs. This implementation does not make use of the
command queue feature. Regular operations using ->exec_op()
use PIO mode for data transfers. Raw, ECC and OOB read/writes
make use of the DMA mode for data transfer.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This adds the devicetree binding for the Tegra 2 NAND flash
controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Gasket (Google ASIC Software, Kernel Extensions, and Tools) kernel
framework is a generic, flexible system that supports thin kernel
drivers. Gasket kernel drivers are expected to handle opening and
closing devices, mmap'ing BAR space as requested, a small selection of
ioctls, and handling page table translation (covered below). Any other
functions should be handled by userspace code.
The Gasket common module is not enough to run a device. In order to
customize the Gasket code for a given piece of hardware, a device
specific module must be created. At a minimum, this module must define a
struct gasket_driver_desc containing the device-specific data for use by
the framework; in addition, the module must declare an __init function
that calls gasket_register_device with the module's gasket_driver_desc
struct. Finally, the driver must define an exit function that calls
gasket_unregister_device with the module's gasket_driver_desc struct.
One of the core assumptions of the Gasket framework is that precisely
one process is allowed to have an open write handle to the device node
at any given time. (That process may, once it has one write handle, open
any number of additional write handles.) This is accomplished by
tracking open and close data for each driver instance.
Signed-off-by: Rob Springer <rspringer@google.com>
Signed-off-by: John Joseph <jnjoseph@google.com>
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>