Cross-merge networking fixes after downstream PR (net-7.1-rc8).
Conflicts:
drivers/net/ethernet/wangxun/txgbe/txgbe_aml.c
f67aead16e ("net: txgbe: rework service event handling")
57d39faed4 ("net: txgbe: improve functions of AML 40G devices")
net/rds/info.c
512db8267b ("rds: mark snapshot pages dirty in rds_info_getsockopt()")
6e94eeb2a2 ("rds: convert to getsockopt_iter")
Adjacent changes:
include/net/sock.h
1ee90b77b7 ("net: guard timestamp cmsgs to real error queue skbs")
f0de88303d ("net: make is_skb_wmem() available to modules")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d1d564ec49 ("gpio: move hogs into GPIO core") introduced a
behaviour change that breaks boot on Raspberry Pi 5 when using the
firmware-supplied device tree:
gpiochip_add_data_with_key: GPIOs 544..575
(/soc@107c000000/gpio@7d517c00) failed to register, -22
brcmstb-gpio 107d517c00.gpio: Could not add gpiochip for bank 1
brcmstb-gpio 107d517c00.gpio: probe with driver brcmstb-gpio failed
with error -22
gpio-brcmstb registers two gpio_chips against the device tree
node gpio@7d517c00, one for each bank. The firmware-supplied DT includes
a gpio-hog on RP1 RUN, and this gpio-hog is attempted to be applied to
*both* gpio_chips. This succeeds against bank 0 (which hosts the GPIO)
and fails for bank 1 (which does not).
In the previous implementation, failures to apply gpio-hogs were
quietly ignored. In the new code, the error code propagates and causes
probe to fail.
Closely approximate the previous behaviour by using the OF_POPULATED flag
to ensure that each gpio-hog is processed only once. The flag was
previously being set before the gpio-hogs were processed, so as part
of this change, the flag now gets set only after the gpio-hog is actioned.
The handling of gpio-hogs on a DT node with multiple gpio_chips remains a
bit incomplete/unclear, but this at least retains the ability to apply
hogs to the first gpio_chip per node.
Fixes: d1d564ec49 ("gpio: move hogs into GPIO core")
Signed-off-by: Daniel Drake <dan@reactivated.net>
Link: https://patch.msgid.link/20260608210108.36248-1-dan@reactivated.net
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If gpiochip_hog_lines() successfully processes some hogs but fails on
a later one, the error handling path in gpiochip_add_data_with_key()
jumps directly to err_remove_of_chip. This leaks resources allocated
earlier for ACPI, interrupts and hogs that were successfully processed.
Use the right label in error path.
Closes: https://sashiko.dev/#/patchset/20260608210108.36248-1-dan%40reactivated.net
Fixes: d1d564ec49 ("gpio: move hogs into GPIO core")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20260609-gpio-hogs-fixes-v1-2-b4064f8070e7@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The driver allocates domain generic chips using
irq_alloc_domain_generic_chips() during probe. However, on driver
remove/teardown, the generic chips are not automatically freed when the
IRQ domain is removed because the domain flags do not include
IRQ_DOMAIN_FLAG_DESTROY_GC.
This causes both the domain generic chips structure and the associated
generic chips to be leaked. Additionally, the generic chips remain on
the global gc_list and may later be visited by generic IRQ chip suspend,
resume, or shutdown callbacks after the GPIO bank has been removed,
potentially resulting in a use-after-free and kernel crash.
Fix the resource leak by explicitly calling
irq_domain_remove_generic_chips() before removing the IRQ domain in
rockchip_gpio_remove().
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Marco Scardovi <scardracs@disroot.org>
Link: https://patch.msgid.link/20260607230504.35392-2-scardracs@disroot.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
gpio-mockup validates only that each second gpio_mockup_ranges value is
non-negative before creating the mock chips. The fixed-base form uses
the second value as the first GPIO number after the range, while the
dynamic-base form uses it as the number of GPIOs.
gpio_mockup_register_chip() stores the resulting number of GPIOs in a
u16 and passes it through a PROPERTY_ENTRY_U16("nr-gpios", ...). Values
greater than U16_MAX therefore truncate silently. For example,
gpio_mockup_ranges=-1,65537 creates a one-line mock GPIO chip instead of
rejecting the invalid request.
Reject zero-width, reversed, and over-U16 ranges before registering any
mock chip.
Assisted-by: Codex:gpt-5.5-cyber-preview
Signed-off-by: Samuel Moelius <sam.moelius@trailofbits.com>
Link: https://patch.msgid.link/20260609004538.1240091.3fba33a20b88.gpio-mockup-ngpio-u16-truncation@trailofbits.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even when it
returns an error. zynq_gpio_remove() uses it to keep the controller active
while removing the GPIO chip, but never drops the usage counter again.
Balance the get with pm_runtime_put_noidle() after disabling runtime PM.
Fixes: 3242ba117e ("gpio: Add driver for Zynq GPIO controller")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Link: https://patch.msgid.link/20260609073313.5-1-ruoyuw560@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
mvebu_pwm_suspend() and mvebu_pwm_resume() are called for all GPIO
banks during suspend/resume, but not all banks have PWM functionality.
GPIO banks without PWM have mvchip->mvpwm set to NULL.
Calling mvebu_pwm_suspend() with mvpwm == NULL causes a NULL pointer
dereference when it tries to access mvpwm->blink_select.
Unable to handle kernel NULL pointer dereference at virtual address 00000020 when write
[00000020] *pgd=00000000
Internal error: Oops: 815 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 UID: 0 PID: 406 Comm: sh Not tainted 6.12.74-rt12-yocto-standard-g4e96f98fb7db-dirty #353
Hardware name: Marvell Armada 370/XP (Device Tree)
PC is at regmap_mmio_read+0x38/0x54
LR is at regmap_mmio_read+0x38/0x54
pc : [<c05fd2ac>] lr : [<c05fd2ac>] psr: 200f0013
sp : f0c11d10 ip : 00000000 fp : c100d2f0
r10: c14fb854 r9 : 00000000 r8 : 00000000
r7 : c1799c00 r6 : 00000020 r5 : 00000020 r4 : c179c7c0
r3 : f0a231a0 r2 : 00000020 r1 : 00000020 r0 : 00000000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 135ec059 DAC: 00000051
Call trace:
regmap_mmio_read from _regmap_bus_reg_read+0x78/0xac
_regmap_bus_reg_read from _regmap_read+0x60/0x154
_regmap_read from regmap_read+0x3c/0x60
regmap_read from mvebu_gpio_suspend+0xa4/0x14c
mvebu_gpio_suspend from dpm_run_callback+0x54/0x180
dpm_run_callback from device_suspend+0x124/0x630
device_suspend from dpm_suspend+0x124/0x270
dpm_suspend from dpm_suspend_start+0x64/0x6c
dpm_suspend_start from suspend_devices_and_enter+0x140/0x8e8
suspend_devices_and_enter from pm_suspend+0x2fc/0x308
pm_suspend from state_store+0x6c/0xc8
state_store from kernfs_fop_write_iter+0x10c/0x1f8
kernfs_fop_write_iter from vfs_write+0x270/0x468
vfs_write from ksys_write+0x70/0xf0
ksys_write from ret_fast_syscall+0x0/0x54
Add a NULL check for mvchip->mvpwm before calling the PWM
suspend/resume functions.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Link: https://patch.msgid.link/20260608084334.2960803-1-yun.zhou@windriver.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Address several teardown issues and resource leaks in the driver's remove
path and error handling:
1. Debounce clock reference leak: The debounce clock (bank->db_clk) is
obtained using of_clk_get() which increments the clock's reference
count, but clk_put() is never called. Register a devm action to
cleanly release it on unbind. Note that of_clk_get(..., 1) remains
necessary over devm_clk_get() because the DT binding does not define
clock-names, precluding name-based lookup.
2. Unregistered chained IRQ handler: The chained IRQ handler is not
disconnected in remove(). If a stray interrupt fires after the driver
is removed, the kernel attempts to execute a stale handler, leading
to a panic. Fix this by clearing the handler in remove().
3. IRQ domain leak: The linear IRQ domain and its generic chips are
allocated manually during probe but never removed. Remove the IRQ
domain during driver teardown to free the associated generic chips
and mappings.
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Marco Scardovi <scardracs@disroot.org>
Link: https://patch.msgid.link/20260526171050.12785-3-scardracs@disroot.org
[Bartosz: don't emit an error message on devres allocation failure]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The bank->clk was previously obtained via of_clk_get() and manually
prepared/enabled. However, it was missing a corresponding clk_put() in
both the error paths and the remove function, leading to a reference leak.
Convert the allocation to devm_clk_get_enabled(), which also properly
propagates failures from clk_prepare_enable() that were previously ignored.
The GPIO bank device uses the same OF node as the previous of_clk_get()
call, so devm_clk_get_enabled(dev, NULL) correctly resolves the same
clock provider entry.
Fix the reference leak and simplify the code by removing the manual
clk_disable_unprepare() calls in the probe error paths and in the
remove function.
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Marco Scardovi <scardracs@disroot.org>
Link: https://patch.msgid.link/20260526171050.12785-2-scardracs@disroot.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If *ppos is non-zero (user-space write split over multiple calls to
write()) then simple_write_to_buffer() won't initialize the start of the
buffer. Really, non-zero values for *ppos aren't going to work at all.
Check for that and return -EINVAL at the start of the function.
Fixes: 91581c4b3f ("gpio: virtuser: new virtual testing driver for the GPIO API")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://patch.msgid.link/ahP3BJWWy-m_qI0X@stanley.mountain
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
By the time gpio_device_teardown_shared() is called, the parent device
is gone from the global list of GPIO devices and all outstanding SRCU
read-side critical sections have completed. That means that no
concurrent gpio_find_and_request() can call
gpio_shared_add_proxy_lookup() for this device at this time. There's
also no risk of the parent device being re-bound to the driver before
the unbinding completes (including the child devices).
Lockdep produces a false-positive report about a possible circular
dependency as it doesn't know the ordering guarantee. Not taking the
ref->lock in gpio_device_teardown_shared() silences it and is safe to do.
Cc: stable@vger.kernel.org
Fixes: ea513dd3c0 ("gpio: shared: make locking more fine-grained")
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260522-gpio-shared-deadlock-v1-2-76bca088f8c0@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Commit 710abda580 ("gpio: shared: call gpio_chip::of_xlate() if set")
used the mutex embedded in struct gpio_shared_entry to protect the
offset field which now can be modified after assignment. The critical
section however is too wide and introduced a potential deadlock on the
removal of the shared GPIO proxy's parent.
Make the critical section shorter - only protect the offset when it's
being read.
While at it: mention the fact that the entry lock is now also used to
protect against concurrent access to the offset field in the structure's
documentation.
Cc: stable@vger.kernel.org
Fixes: 710abda580 ("gpio: shared: call gpio_chip::of_xlate() if set")
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260522-gpio-shared-deadlock-v1-1-76bca088f8c0@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If port->irq_high is -1 (fsl,imx21-gpio compatible) and gpio_idx is >= 16
enable_irq_wake() is called with -1 which is wrong.
Fixes: 5f6d1998ad ("gpio: mxc: release the parent IRQ in runtime suspend")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260526063504.25916-1-alexander.stein@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
On error we free aggr->lookups->dev_id before removing the entry from
the lookup table. If a concurrent thread calls gpiod_find() before we
remove the entry, it could iterate over the list and call
gpiod_match_lookup_table() which unconditionally dereferences dev_id
when calling strcmp(). Reverse the order of cleanup.
Fixes: 86f162e73d ("gpio: aggregator: introduce basic configfs interface")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520084911.27938-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
We check the padding of other uAPI v2 structures but not that of line
config attributes. For used attributes: check if their padding is
zeroed, for unused: check if the entire structure is zeroed.
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Link: https://patch.msgid.link/20260521-gpio-cdev-attr-padding-check-v3-1-ec3bcbe2e358@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
pca953x_resume() returns 0 when regulator_enable() fails, dropping
the real error code and masking the failure as a successful resume.
The caller then proceeds as if the chip is powered, while the
regulator is in fact disabled.
Return ret so PM core sees the actual failure.
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260520110504.13969-1-sozdayvek@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
- fix a regression in gpio-rockchip introduced on older chips during the
merge window when converting to dynamic GPIO base
- fix AST2700 debounce selector bit definitions in gpio-aspeed
-----BEGIN PGP SIGNATURE-----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=H+NQ
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix a regression in gpio-rockchip introduced on older chips during
the merge window when converting to dynamic GPIO base
- fix AST2700 debounce selector bit definitions in gpio-aspeed
* tag 'gpio-fixes-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: aspeed: fix AST2700 debounce selector bit definitions
gpio: rockchip: Fix GPIO regression after conversion to dynamic base allocation
The ath9k has an odd use of system-wide GPIOs: if the chip
does not have internal GPIO capability, it will try to obtain a
GPIO line from the system GPIO controller:
if (BIT(gpio) & ah->caps.gpio_mask)
ath9k_hw_gpio_cfg_wmac(...);
else if (AR_SREV_SOC(ah))
ath9k_hw_gpio_cfg_soc(ah, gpio, out, label);
Where ath9k_hw_gpio_cfg_soc() will attempt to issue
gpio_request_one() passing the local GPIO number of the controller
(0..31) to gpio_request_one().
This is somewhat peculiar and possibly even dangerous: there is
nowadays no guarantee of the numbering of these system-wide
GPIOs, and assuming that GPIO 0..31 as used by ath9k would
correspond to GPIOs 0..31 on the system as a whole seems a bit
wild.
Register all 32 GPIOs at index 0..31 directly in the ATH79K
GPIO driver and associate with the NULL device (making them
widely available) if and only if we are probing ATH79K wifi
from the AHB bus (used for SoCs). We obtain these offsets from
the NULL device if necessary.
These GPIOs should ideally be defined in the device tree
instead, but we have no control over that for the legacy
code path.
Testcompiled with the ath79 defconfig.
Reported-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Link: https://patch.msgid.link/20260317-descriptors-wireless-v6-1-b19ecff9cd2b@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The AST2700 datasheet defines reg_debounce_sel1 as the low bit and
reg_debounce_sel2 as the high bit. The current driver uses the AST2600
mapping instead, where sel1 is the high bit and sel2 is the low bit.
As a result, the debounce selector bits are programmed in reverse on
AST2700. Swap the G7 sel1/sel2 bit definitions so the driver matches the
hardware definition.
Fixes: b2e861bd1e ("gpio: aspeed: Support G7 Aspeed gpio controller")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://patch.msgid.link/20260415-gpio-fix-v1-1-b08a89b31e6f@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The commit c8079f83e0 ("gpio: rockchip: convert to dynamic GPIO base
allocation") broke GPIO on devices using device trees which don't set
the gpio-ranges property, something only Rockchip RK35xx SoC DTs do.
On a Rockchip RK3399 device something like following is now observed:
[ 0.082771] rockchip-gpio ff720000.gpio: probed /pinctrl/gpio@ff720000
[ 0.083531] rockchip-gpio ff730000.gpio: probed /pinctrl/gpio@ff730000
[ 0.084110] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000
[ 0.084746] rockchip-gpio ff788000.gpio: probed /pinctrl/gpio@ff788000
[ 0.085389] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000
--
[ 0.212208] rockchip-pinctrl pinctrl: pin 637 is not registered so it cannot be requested
[ 0.212271] rockchip-pinctrl pinctrl: error -EINVAL: pin-637 (gpio3:637)
[ 0.212344] leds-gpio leds: error -EINVAL: Failed to get GPIO '/leds/led-0'
[ 0.212389] leds-gpio leds: probe with driver leds-gpio failed with error -22
--
[ 0.607545] rockchip-pinctrl pinctrl: pin 519 is not registered so it cannot be requested
[ 0.608775] rockchip-pinctrl pinctrl: error -EINVAL: pin-519 (gpio0:519)
[ 0.610003] dwmmc_rockchip fe320000.mmc: probe with driver dwmmc_rockchip failed with error -22
--
[ 0.805882] rockchip-pinctrl pinctrl: pin 547 is not registered so it cannot be requested
[ 0.806672] rockchip-pinctrl pinctrl: error -EINVAL: pin-547 (gpio1:547)
[ 0.807301] reg-fixed-voltage regulator-vbus-typec: error -EINVAL: can't get GPIO
[ 0.807307] rockchip-pinctrl pinctrl: pin 602 is not registered so it cannot be requested
[ 0.807970] reg-fixed-voltage regulator-vbus-typec: probe with driver reg-fixed-voltage failed with error -22
[ 0.808692] rockchip-pinctrl pinctrl: error -EINVAL: pin-602 (gpio2:602)
[ 0.810279] reg-fixed-voltage regulator-vcc3v3-pcie: error -EINVAL: can't get GPIO
[ 0.810284] rockchip-pinctrl pinctrl: pin 665 is not registered so it cannot be requested
[ 0.810299] rockchip-pinctrl pinctrl: error -EINVAL: pin-665 (gpio4:665)
[ 0.810960] reg-fixed-voltage regulator-vcc3v3-pcie: probe with driver reg-fixed-voltage failed with error -22
[ 0.811679] reg-fixed-voltage regulator-vcc5v0-host: error -EINVAL: can't get GPIO
[ 0.813943] reg-fixed-voltage regulator-vcc5v0-host: probe with driver reg-fixed-voltage failed with error -22
--
[ 0.867788] rockchip-pinctrl pinctrl: pin 522 is not registered so it cannot be requested
[ 0.868537] rockchip-pinctrl pinctrl: error -EINVAL: pin-522 (gpio0:522)
[ 0.869166] pwrseq_simple sdio-pwrseq: error -EINVAL: reset GPIOs not ready
[ 0.869798] pwrseq_simple sdio-pwrseq: probe with driver pwrseq_simple failed with error -22
--
[ 0.940365] rockchip-pinctrl pinctrl: pin 623 is not registered so it cannot be requested
[ 0.941084] rockchip-pinctrl pinctrl: error -EINVAL: pin-623 (gpio3:623)
[ 0.941823] rk_gmac-dwmac fe300000.ethernet: error -EINVAL: Cannot register the MDIO bus
[ 0.942542] rk_gmac-dwmac fe300000.ethernet: error -EINVAL: MDIO bus (id: 0) registration failed
[ 0.943772] rk_gmac-dwmac fe300000.ethernet: probe with driver rk_gmac-dwmac failed with error -22
Restore GPIO to a working state on devices using older Rockchip SoCs
and/or DTs not having the gpio-ranges property set by restoring prior
use of bank->pin_base as the pin_offset value.
Also change to use bank->nr_pins as the npins value to align and prevent
a possible future breakage if gc->ngpio is ever changed to match the 32
GPIOs each controller theoretically can handle.
Fixes: c8079f83e0 ("gpio: rockchip: convert to dynamic GPIO base allocation")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260416154928.2103388-1-jonas@kwiboo.se
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Core changes:
- Perform basic checks on pin config properties so as not to
allow directly contradictory settings such as setting a pin
to more than one bias or drive mode.
- Handle input-threshold-voltage-microvolt property.
- Introduce pinctrl_gpio_get_config() handling in the core for
SCMI GPIO using pin control.
New drivers:
- GPIO-by-pin control driver (also apperaing in the GPIO pull
request) fulfilling a promise on a comment from
Grant Likely many years ago: "can't GPIO just be a front-end
for pin control?" it turns out it can, if and only if you
design something new from scratch, such as SCMI.
- Broadcom BCM7038 as a pinctrl-single delegate.
- Mobileye EyeQ6Lplus OLB pin controller.
- Qualcomm Eliza and Hawi families TLMM pin controllers.
- Qualcomm SDM670 and Milos family LPASS LPI pin controllers.
- Qualcomm IPQ5210 pin controller.
- Realtek RTD1625 pin controller support.
- Rockchip RV1103B pin controller support.
- Texas Instruments AM62L as a pinctrl-single delegate.
Improvements:
- Set config implementation for the Spacemit K1 pin controller.
-----BEGIN PGP SIGNATURE-----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=mkXM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Perform basic checks on pin config properties so as not to allow
directly contradictory settings such as setting a pin to more than
one bias or drive mode
- Handle input-threshold-voltage-microvolt property
- Introduce pinctrl_gpio_get_config() handling in the core for SCMI
GPIO using pin control
New drivers:
- GPIO-by-pin control driver (also appearing in the GPIO pull
request) fulfilling a promise on a comment from Grant Likely many
years ago: "can't GPIO just be a front-end for pin control?" it
turns out it can, if and only if you design something new from
scratch, such as SCMI
- Broadcom BCM7038 as a pinctrl-single delegate
- Mobileye EyeQ6Lplus OLB pin controller
- Qualcomm Eliza and Hawi families TLMM pin controllers
- Qualcomm SDM670 and Milos family LPASS LPI pin controllers
- Qualcomm IPQ5210 pin controller
- Realtek RTD1625 pin controller support
- Rockchip RV1103B pin controller support
- Texas Instruments AM62L as a pinctrl-single delegate
Improvements:
- Set config implementation for the Spacemit K1 pin controller"
* tag 'pinctrl-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (84 commits)
pinctrl: qcom: Add Hawi pinctrl driver
dt-bindings: pinctrl: qcom: Describe Hawi TLMM block
dt-bindings: pinctrl: pinctrl-max77620: convert to DT schema
pinctrl: single: Add bcm7038-padconf compatible matching
dt-bindings: pinctrl: pinctrl-single: Add brcm,bcm7038-padconf
dt-bindings: pinctrl: apple,pinctrl: Add t8122 compatible
pinctrl: qcom: sdm670-lpass-lpi: label variables as static
pinctrl: sophgo: pinctrl-sg2044: Fix wrong module description
pinctrl: sophgo: pinctrl-sg2042: Fix wrong module description
pinctrl: qcom: add sdm670 lpi tlmm
dt-bindings: pinctrl: qcom: Add SDM670 LPASS LPI pinctrl
dt-bindings: qcom: lpass-lpi-common: add reserved GPIOs property
pinctrl: qcom: Introduce IPQ5210 TLMM driver
dt-bindings: pinctrl: qcom: add IPQ5210 pinctrl
pinctrl: qcom: Drop redundant intr_target_reg on modern SoCs
pinctrl: qcom: eliza: Fix interrupt target bit
pinctrl: core: Don't use "proxy" headers
pinctrl: amd: Support new ACPI ID AMDI0033
pinctrl: renesas: rzg2l: Drop superfluous blank line
pinctrl: renesas: rzg2l: Fix save/restore of {IOLH,IEN,PUPD,SMT} registers
...
The driver updates again are all over the place with many minor fixes
going into platform specific code. The most notable changes are:
- Support for Microchip pic64gx system controllers
- Work on cleaning up devicetree bindings for SoC drivers, and
converting them into the new format
- Lots of smaller changes for Qualcomm SoC drivers, including support
for a number of newly supported chips
- reset controller API cleanups and a new driver for Cix Sky1
- Reworks of the Tegra PMC and CBB drivers, along with a change
to how individual Tegra SoCs get selected in Kconfig and
BPMP firmware driver updates including a refresh of the ABI
header to match the version used by firmware
- STM32 updates to the firewall bus driver and support for
the debug bus through OP-TEE
- SCMI firmware driver improvements for reliability, in particular
for dealing with broken firmware interrupts
- Memory driver updates for Tegra, and a patch to remove the
unused Baikal T1 driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmnhCSYACgkQmmx57+YA
GNl2ow/+Pti7qbBE34WNyIuWOgZEzjo1OeLe/Y4LqkQmHcM9FJV3/rCadA/FkmD9
nH85WiRuUjIjzUiAl24SP2nkEcIU/yv8ECvROX46uAjhTByVHkaCedwl3ECW9RPA
IAYiTJPrQBNCmWZuGO4bZ3go6hHn4q4RSd2V8vrCw/J3b+wBSAPTPzsaWnWg4MiL
QYz7sBTwcNJaJuwJ7ZnHN/VgEOs9OgY6ejGJImiaVzBbsH7rNp7Cbs6t88X5rCXS
mbgMvVlYKbsOWj3kNyv98YFAGgzo59uEL+m+846U32w9o0nIgkmIS60RQ5k73JV4
QlhV1uT7PPtu7y7VbxfJ8KISxaRoex/+AZShmAWCul4YK75hEWT3mWGhM8cqeMUQ
U0ogpbekRjKdn2Bgfl6kHf38smusjJ1fOBr8QIZcdDJpEtxYtRmNpLUNNSc5vO+T
HvA79C8I8ydWGyqr1wRP1gDRBNc1BDYKxJO4ohvjnAPIeC01zArXCOyf0F3VtPzH
XSycnyW7eRUVi+4C3/cF8qzhW2y7Wx03ui5mCDIEcOzyVoGNqTrPNsbCvkNkyrdc
jqvWagZ4Ci8jaRxLAawnqHI/stvsHx9V+NPp6p07BsOxJMsuOqO4sInRhh5P6YvM
5wZCFUK37xPEqYvr+BFS9B/4jgw3Mg2Kj+gjxShwsLS5JtVDfZw=
=UB4F
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The driver updates again are all over the place with many minor fixes
going into platform specific code. The most notable changes are:
- Support for Microchip pic64gx system controllers
- Work on cleaning up devicetree bindings for SoC drivers, and
converting them into the new format
- Lots of smaller changes for Qualcomm SoC drivers, including support
for a number of newly supported chips
- reset controller API cleanups and a new driver for Cix Sky1
- Reworks of the Tegra PMC and CBB drivers, along with a change to
how individual Tegra SoCs get selected in Kconfig and BPMP firmware
driver updates including a refresh of the ABI header to match the
version used by firmware
- STM32 updates to the firewall bus driver and support for the debug
bus through OP-TEE
- SCMI firmware driver improvements for reliability, in particular
for dealing with broken firmware interrupts
- Memory driver updates for Tegra, and a patch to remove the unused
Baikal T1 driver"
* tag 'soc-drivers-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (193 commits)
firmware: arm_ffa: Use the correct buffer size during RXTX_MAP
firmware: qcom: scm: Allow QSEECOM on Lenovo IdeaCentre Mini X
clk: spear: fix resource leak in clk_register_vco_pll()
reset: rzv2h-usb2phy: Add support for VBUS mux controller registration
reset: rzv2h-usb2phy: Convert to regmap API
dt-bindings: reset: renesas,rzv2h-usb2phy: Document RZ/G3E USB2PHY reset
dt-bindings: reset: renesas,rzv2h-usb2phy: Add '#mux-state-cells' property
soc: microchip: add mpfs gpio interrupt mux driver
dt-bindings: soc: microchip: document PolarFire SoC's gpio interrupt mux
gpio: mpfs: Add interrupt support
soc: qcom: ubwc: add helpers to get programmable values
soc: qcom: ubwc: add helper to get min_acc length
firmware: qcom: scm: Register gunyah watchdog device
soc: qcom: socinfo: Add SoC ID for SA8650P
dt-bindings: arm: qcom,ids: Add SoC ID for SA8650P
firmware: qcom: scm: Allow QSEECOM on Mahua CRD
soc: qcom: wcnss: simplify allocation of req
soc: qcom: pd-mapper: Add support for Eliza
soc: qcom: aoss: compare against normalized cooling state
soc: qcom: llcc: fix v1 SB syndrome register offset
...
-----BEGIN PGP SIGNATURE-----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=3RtB
-----END PGP SIGNATURE-----
Merge tag 'media/v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CSI tegra support, covering Tegra20 and Tegra30
- new camera sensor drivers: T4ka3 and ov2732
- m88ds3103: add 3103c chip support
- uvcvideo: add support for Intel RealSense D436/D555 and P010 pixel format
- synopsys csi2rx: add i.MX93 support
- imx8-isi: add i.MX95 support
- imx8mq-mipi-csi2: add i.MX8ULP support
- dw100: add V4L2 requests support
- support for DTV devices from Hauppauge got some improvements
- media staging: dropped starfive-camss driver
- media docs: document multi-committers model and improve maint profile
- media core:
- add v4l2_subdev_get_frame_desc_passthrough() helper
- improve error handling in fwnode parsing
- lots of driver fixes, cleanups and improvements
* tag 'media/v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (251 commits)
Revert "media: cx231xx: add USB ID 2040:8360 for Hauppauge WinTV-HVR-935"
media: synopsys: csi2rx: add i.MX93 support
media: dt-bindings: add NXP i.MX93 compatible string
media: synopsys: csi2rx: Use enum and u32 array for register offsets
media: synopsys: csi2rx: implement .get_frame_desc() callback
media: synopsys: csi2rx: only check errors from devm_clk_bulk_get_all()
media: synopsys: csi2rx: use devm_reset_control_get_optional_exclusive()
media: i2c: imx283: add support for non-continuous MIPI clock mode
media: i2c: ov08d10: add support for 24 MHz input clock
media: i2c: ov08d10: add support for reset and power management
media: i2c: ov08d10: add support for binding via device tree
dt-bindings: media: i2c: document Omnivision OV08D10 CMOS image sensor
media: i2c: ov08d10: add missing newline to prints
media: i2c: ov08d10: fix some typos in comments
media: i2c: ov08d10: remove duplicate register write
media: i2c: ov08d10: fix image vertical start setting
media: i2c: ov08d10: fix runtime PM handling in probe
staging: media: ipu7: Update TODO
media: Add t4ka3 camera sensor driver
media: i2c: Add ov2732 image sensor driver
...
GPIO core:
- defer probe on software node lookups when the remote software node
exists but has not been registered as a firmware node yet
- unify GPIO hog handling by moving code duplicated in OF and ACPI
modules into GPIO core and allow setting up hogs with software nodes
- allow matching GPIO controllers by secondary firmware node if matching
by primary does not succeed
- demote deferral warnings to debug level as they are quite normal when
using software nodes which don't support fw_devlink yet
- disable the legacy GPIO character device uAPI v1 supprt in Kconfig by
default
- rework several core functions in preparation for the upcoming Revocable
helper library for protecting resources against sudden removal, this
reduces the number of SRCU dereferences in GPIO core
- simplify file descriptor logic in GPIO character device code by using
FD_PREPARE()
- introduce a header defining symbols used by both GPIO consumers and
providers to avoid having to include provider-specific headers from
drivers which only consume GPIOs
- replace snprintf() with strscpy() where formatting is not required
New drivers:
- add the gpio-by-pinctrl generic driver using the ARM SCMI protocol to
control GPIOs (along with SCMI changes pulled from the pinctrl tree)
- add a driver providing support for handling of platform events via
GPIO-signalled ACPI events (used on Intel Nova Lake and later platforms)
Driver changes:
- extend the gpio-kempld driver with support for more recent models,
interrupts and setting/getting multiple values at once
- improve interrupt handling in gpio-brcmstb
- add support for multi-SoC systems in gpio-tegra186
- make sure we return correct values from the .get() callbacks in several
GPIO drivers by normalizing any values other than 0, 1 or negative error
numbers
- use flexible arrays in several drivers to reduce the number of required
memory allocations
- simplify synchronous waiting for virtual drivers to probe and remove the
dedicated, a bit overengineered helper library dev-sync-probe
- remove unneeded Kconfig dependencies on OF_GPIO in several drivers and
subsystems
- convert the two remaining users of of_get_named_gpio() to using GPIO
descriptors and remove the (no longer used) function along with the
header that declares it
- add missing includes in gpio-mmio
- shrink and simplify code in gpio-max732x by using guard(mutex)
- remove duplicated code handling the 'ngpios' property from gpio-ts4800,
it's already handled in GPIO core
- use correct variable type in gpio-aspeed
- add support for a new model in gpio-realtek-otto
- allow to specify the active-low setting of simulated hogs over the
configfs interface (in addition to existing devicetree support) in
gpio-sim
Bug fixes:
- clear the OF_POPULATED flag on hog nodes in GPIO chip remove path on
OF systems
- fix resource leaks in error path in gpiochip_add_data_with_key()
- drop redundant device reference in gpio-mpsse
Tests:
- add selftests for use-after-free cases in GPIO character device code
DT bindings:
- add a DT binding document for SCMI based, gpio-over-pinctrl devices
- fix interrupt description in microchip,mpfs-gpio
- add new compatible for gpio-realtek-otto
- describe the resets of the mpfs-gpio controller
- fix maintainer's email in gpio-delay bindings
- remove the binding document for cavium,thunder-8890 as the corresponding
device is bound over PCI and not firmware nodes
Documentation:
- update the recommended way of converting legacy boards to using software
nodes for GPIO description
- describe GPIO line value semantics
- misc updates to kerneldocs
Misc:
- convert OMAP1 ams-delta board to using GPIO hogs described with software
nodes
-----BEGIN PGP SIGNATURE-----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=VknJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"For this merge window we have two new drivers: support for
GPIO-signalled ACPI events on Intel platforms and a generic
GPIO-over-pinctrl driver using the ARM SCMI protocol for
controlling pins.
Several things have been reworked in GPIO core: we unduplicated GPIO
hog handling, reduced the number of SRCU locks and dereferences,
improved support for software-node-based lookup and removed more
legacy code after converting remaining users to modern alternatives.
There's also a number of driver reworks and refactoring, documentation
updates, some bug-fixes and new tests.
GPIO core:
- defer probe on software node lookups when the remote software node
exists but has not been registered as a firmware node yet
- unify GPIO hog handling by moving code duplicated in OF and ACPI
modules into GPIO core and allow setting up hogs with software
nodes
- allow matching GPIO controllers by secondary firmware node if
matching by primary does not succeed
- demote deferral warnings to debug level as they are quite normal
when using software nodes which don't support fw_devlink yet
- disable the legacy GPIO character device uAPI v1 supprt in Kconfig
by default
- rework several core functions in preparation for the upcoming
Revocable helper library for protecting resources against sudden
removal, this reduces the number of SRCU dereferences in GPIO core
- simplify file descriptor logic in GPIO character device code by
using FD_PREPARE()
- introduce a header defining symbols used by both GPIO consumers and
providers to avoid having to include provider-specific headers from
drivers which only consume GPIOs
- replace snprintf() with strscpy() where formatting is not required
New drivers:
- add the gpio-by-pinctrl generic driver using the ARM SCMI protocol
to control GPIOs (along with SCMI changes pulled from the pinctrl
tree)
- add a driver providing support for handling of platform events via
GPIO-signalled ACPI events (used on Intel Nova Lake and later
platforms)
Driver changes:
- extend the gpio-kempld driver with support for more recent models,
interrupts and setting/getting multiple values at once
- improve interrupt handling in gpio-brcmstb
- add support for multi-SoC systems in gpio-tegra186
- make sure we return correct values from the .get() callbacks in
several GPIO drivers by normalizing any values other than 0, 1 or
negative error numbers
- use flexible arrays in several drivers to reduce the number of
required memory allocations
- simplify synchronous waiting for virtual drivers to probe and
remove the dedicated, a bit overengineered helper library
dev-sync-probe
- remove unneeded Kconfig dependencies on OF_GPIO in several drivers
and subsystems
- convert the two remaining users of of_get_named_gpio() to using
GPIO descriptors and remove the (no longer used) function along
with the header that declares it
- add missing includes in gpio-mmio
- shrink and simplify code in gpio-max732x by using guard(mutex)
- remove duplicated code handling the 'ngpios' property from
gpio-ts4800, it's already handled in GPIO core
- use correct variable type in gpio-aspeed
- add support for a new model in gpio-realtek-otto
- allow to specify the active-low setting of simulated hogs over the
configfs interface (in addition to existing devicetree support) in
gpio-sim
Bug fixes:
- clear the OF_POPULATED flag on hog nodes in GPIO chip remove path
on OF systems
- fix resource leaks in error path in gpiochip_add_data_with_key()
- drop redundant device reference in gpio-mpsse
Tests:
- add selftests for use-after-free cases in GPIO character device
code
DT bindings:
- add a DT binding document for SCMI based, gpio-over-pinctrl devices
- fix interrupt description in microchip,mpfs-gpio
- add new compatible for gpio-realtek-otto
- describe the resets of the mpfs-gpio controller
- fix maintainer's email in gpio-delay bindings
- remove the binding document for cavium,thunder-8890 as the
corresponding device is bound over PCI and not firmware nodes
Documentation:
- update the recommended way of converting legacy boards to using
software nodes for GPIO description
- describe GPIO line value semantics
- misc updates to kerneldocs
Misc:
- convert OMAP1 ams-delta board to using GPIO hogs described with
software nodes"
* tag 'gpio-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (79 commits)
gpio: swnode: defer probe on references to unregistered software nodes
dt-bindings: gpio: cavium,thunder-8890: Remove DT binding
Documentation: gpio: update the preferred method for using software node lookup
gpio: gpio-by-pinctrl: s/used to do/is used to do/
gpio: aspeed: fix unsigned long int declaration
gpio: rockchip: convert to dynamic GPIO base allocation
gpio: remove dev-sync-probe
gpio: virtuser: stop using dev-sync-probe
gpio: aggregator: stop using dev-sync-probe
gpio: sim: stop using dev-sync-probe
gpio: Add Intel Nova Lake ACPI GPIO events driver
gpiolib: Make deferral warnings debug messages
gpiolib: fix hogs with multiple lines
gpio: fix up CONFIG_OF dependencies
gpio: gpio-by-pinctrl: add pinctrl based generic GPIO driver
gpio: dt-bindings: Add GPIO on top of generic pin control
firmware: arm_scmi: Allow PINCTRL_REQUEST to return EOPNOTSUPP
pinctrl: scmi: ignore PIN_CONFIG_PERSIST_STATE
pinctrl: scmi: Delete PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS support
pinctrl: scmi: Add SCMI_PIN_INPUT_VALUE
...
devm_kzalloc() failure in tegra_gpio_probe() returns -ENODEV, which
indicates "no such device". The correct error code for a memory
allocation failure is -ENOMEM.
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Link: https://patch.msgid.link/20260409185853.2163034-1-samasth.norway.ananda@oracle.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
fwnode_property_get_reference_args() now returns -ENOTCONN when called
on a software node referencing another software node which has not yet
been registered as a firmware node. It makes sense to defer probe in this
situation as the node will most likely be registered later on and we'll
be able to resolve the reference eventually. Change the behavior of
swnode_find_gpio() to return -EPROBE_DEFER if the software node reference
resolution returns -ENOTCONN.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260407-swnode-unreg-retcode-v4-2-1b2f0725eb9c@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
tegra_gpio_irq_release_resources() erroneously calls tegra_gpio_enable()
instead of tegra_gpio_disable(). When IRQ resources are released, the
GPIO configuration bit (CNF) should be cleared to deconfigure the pin as
a GPIO. Leaving it enabled wastes power and can cause unexpected behavior
if the pin is later reused for an alternate function via pinctrl.
Fixes: 66fecef5bd ("gpio: tegra: Convert to gpio_irq_chip")
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Link: https://patch.msgid.link/20260407210247.1737938-1-samasth.norway.ananda@oracle.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Currently the probe does not check whether getting the regmap succeeded.
This can cause crash when regmap is used, if it wasn't successfully
obtained. Failing to get the regmap is unlikely, especially since this
driver is expected to be kicked by the MFD driver only after registering
the regmap - but it is still better to handle this gracefully.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e7eef0bd4075 ("regulator: bd71828-regulator.c: Fix LDON-HEAD mode")
Link: https://patch.msgid.link/5bfffee380863bcf24f3062e48094c8eb7b1342f.1775565381.git.mazziesaccount@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add missing "is" to the driver's help text ("used to do" has a
completely different meaning).
Fixes: 7671f4949a ("gpio: gpio-by-pinctrl: add pinctrl based generic GPIO driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/b1ecb31a37f8e35447122554a38985cb6240eb11.1775556619.git.geert+renesas@glider.be
[Bartosz: tweak the help text even more]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Replace "unsigned long int" with "unsigned long" to follow Linux kernel
coding style. No functional change intended.
Signed-off-by: Chen Jung Ku <ku.loong@gapp.nthu.edu.tw>
Link: https://patch.msgid.link/20260405144803.31358-1-ku.loong@gapp.nthu.edu.tw
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This driver is used on device tree based platform. Use dynamic
GPIO numberspace base to suppress the warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation.
gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation.
gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/1774864401-177149-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
dev-err-probe is an overengineered solution to a simple problem. Use a
combination of wait_for_probe() and device_is_bound() to synchronously
wait for the platform device to probe.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260327-gpio-kill-dev-sync-probe-v1-3-efac254f1a1d@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
dev-err-probe is an overengineered solution to a simple problem. Use a
combination of wait_for_probe() and device_is_bound() to synchronously
wait for the platform device to probe.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260327-gpio-kill-dev-sync-probe-v1-2-efac254f1a1d@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
dev-err-probe is an overengineered solution to a simple problem. Use a
combination of wait_for_probe() and device_is_bound() to synchronously
wait for the platform device to probe.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260327-gpio-kill-dev-sync-probe-v1-1-efac254f1a1d@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This driver provides support for new way of handling platform events,
through the use of GPIO-signaled ACPI events. This mechanism is used on
Intel client platforms released in 2026 and later, starting with Intel
Nova Lake.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260401174526.60881-1-alan.borzeszkowski@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
With the recent addition of the shared GPIO support, warning messages
such as the following are being observed ...
reg-fixed-voltage regulator-vdd-3v3-pcie: cannot find GPIO chip
gpiolib_shared.proxy.6, deferring
These are seen even with GPIO_SHARED_PROXY=y.
Given that the GPIOs are successfully found a bit later during boot and
the code is intentionally returning -EPROBE_DEFER when they are not
found, downgrade these messages to debug prints to avoid unnecessary
warnings being observed.
Note that although the 'cannot find GPIO line' warning has not been
observed in this case, it seems reasonable to make this print a debug
print for consistency too.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260401133441.47641-1-jonathanh@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add support for interrupts to the PolarFire SoC GPIO driver. Each GPIO
has an independent interrupt that is wired to an interrupt mux that sits
between the controllers and the PLIC. The SoC has more GPIO lines than
connections from the mux to the PLIC, so some GPIOs must share PLIC
interrupts. The configuration is not static and is set at runtime,
conventionally by the platform's firmware. CoreGPIO, the version
intended for use in the FPGA fabric has two interrupt output ports, one
is IO_NUM bits wide, as is used in the hardened cores, and the other is
a single bit with all lines ORed together.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Commit 710abda580 ("gpio: shared: call gpio_chip::of_xlate() if set")
introduced a critical section around the adjustmenet of entry->offset.
However this may cause a deadlock if we create the auxiliary shared
proxy devices with this lock taken. We only need to protect
entry->offset while it's read/written so shorten the critical section
and release the lock before creating the proxy device as the field in
question is no longer accessed at this point.
Fixes: 710abda580 ("gpio: shared: call gpio_chip::of_xlate() if set")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260325-gpio-shared-deadlock-v1-1-e4e7a5319e95@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Suspend may fail on i.MX8QM when Falling Edge is used as a pad wakeup
trigger due to a hardware bug in the detection logic. Since the hardware
does not support Both Edge wakeup, remap requests for Both Edge to Rising
Edge by default to avoid hitting this issue.
A warning is emitted when Falling Edge is selected on i.MX8QM.
Fixes: f60c9eac54 ("gpio: mxc: enable pad wakeup on i.MX8x platforms")
cc: stable@vger.kernel.org
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://patch.msgid.link/20260324192129.2797237-1-shenwei.wang@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
A number of GPIO drivers that used to have a CONFIG_OF_GPIO dependency now fail
to build on targets without CONFIG_OF:
WARNING: unmet direct dependencies detected for GPIO_SYSCON
Depends on [n]: GPIOLIB [=y] && HAS_IOMEM [=y] && MFD_SYSCON [=y] && OF [=n]
Selected by [y]:
- GPIO_SAMA5D2_PIOBU [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && MFD_SYSCON [=y] && (ARCH_AT91 || COMPILE_TEST [=y])
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_bank_probe':
drivers/gpio/gpio-mt7621.c:254:20: error: 'struct gpio_chip' has no member named 'of_gpio_n_cells'
254 | rg->chip.gc.of_gpio_n_cells = 2;
| ^
drivers/gpio/gpio-tegra186.c: In function 'tegra186_gpio_of_xlate':
drivers/gpio/gpio-tegra186.c:502:25: error: 'struct gpio_chip' has no member named 'of_gpio_n_cells'
502 | if (WARN_ON(chip->of_gpio_n_cells < 2))
| ^~
drivers/gpio/gpio-lpc32xx.c: In function 'lpc32xx_gpio_probe':
drivers/gpio/gpio-lpc32xx.c:523:49: error: 'struct gpio_chip' has no member named 'of_xlate'
523 | lpc32xx_gpiochip[i].chip.of_xlate = lpc32xx_of_xlate;
| ^
drivers/gpio/gpio-spacemit-k1.c: In function 'spacemit_gpio_add_bank':
drivers/gpio/gpio-spacemit-k1.c:234:11: error: 'struct gpio_chip' has no member named 'of_gpio_n_cells'
234 | gc->of_gpio_n_cells = 3;
| ^~
Bring that back as a dependency.
Fixes: 7803501e57 ("gpio: drop unneeded Kconfig dependencies on OF_GPIO")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260325100144.1696731-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
