The PLL14xx hardware can be found on i.MX8M{M,N,P} SoCs and always come
with a 6-bit pre-divider. Neither the reference manuals nor the
datasheets of these SoCs do mention any restrictions. Furthermore the
current code doesn't respect the restrictions from the comment too.
Therefore drop the restriction and align the max pre-divider (pdiv)
value to 63 to get more accurate frequencies.
Fixes: b09c68dc57 ("clk: imx: pll14xx: Support dynamic rates")
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.
This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:
- sai5 is running normally and divides Audio PLL out by 16.
- Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
- rates for children are recalculated and rates are set recursively
- imx8m_clk_composite_divider_set_rate(sai5) is called with
32/16 = 2Hz more
- imx8m_clk_composite_divider_set_rate computes same divider as before
- divider register is written, so it restarts counting from zero and
MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.
Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.
Fixes: d3ff972813 ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The kprobes optimization check can_optimize() calls
insn_is_indirect_jump() to detect indirect jump instructions in
a target function. If any is found, creating an optprobe is disallowed
in the function because the jump could be from a jump table and could
potentially land in the middle of the target optprobe.
With retpolines, insn_is_indirect_jump() additionally looks for calls to
indirect thunks which the compiler potentially used to replace original
jumps. This extra check is however unnecessary because jump tables are
disabled when the kernel is built with retpolines. The same is currently
the case with IBT.
Based on this observation, remove the logic to look for calls to
indirect thunks and skip the check for indirect jumps altogether if the
kernel is built with retpolines or IBT. Remove subsequently the symbols
__indirect_thunk_start and __indirect_thunk_end which are no longer
needed.
Dropping this logic indirectly fixes a problem where the range
[__indirect_thunk_start, __indirect_thunk_end] wrongly included also the
return thunk. It caused that machines which used the return thunk as
a mitigation and didn't have it patched by any alternative ended up not
being able to use optprobes in any regular function.
Fixes: 0b53c374b9 ("x86/retpoline: Use -mfunction-return")
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20230711091952.27944-3-petr.pavlu@suse.com
Add Logitech MX Anywhere 3 connected over Bluetooth to the device table
to get hidpi scroll supported. USB connection over the Unifying receiver
is already supported by the wildcard entry LDJ_DEVICE(HID_ANY_ID).
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linker script arch/x86/kernel/vmlinux.lds.S matches the thunk
sections ".text.__x86.*" from arch/x86/lib/retpoline.S as follows:
.text {
[...]
TEXT_TEXT
[...]
__indirect_thunk_start = .;
*(.text.__x86.*)
__indirect_thunk_end = .;
[...]
}
Macro TEXT_TEXT references TEXT_MAIN which normally expands to only
".text". However, with CONFIG_LTO_CLANG, TEXT_MAIN becomes
".text .text.[0-9a-zA-Z_]*" which wrongly matches also the thunk
sections. The output layout is then different than expected. For
instance, the currently defined range [__indirect_thunk_start,
__indirect_thunk_end] becomes empty.
Prevent the problem by using ".." as the first separator, for example,
".text..__x86.indirect_thunk". This pattern is utilized by other
explicit section names which start with one of the standard prefixes,
such as ".text" or ".data", and that need to be individually selected in
the linker script.
[ nathan: Fix conflicts with SRSO and fold in fix issue brought up by
Andrew Cooper in post-review:
https://lore.kernel.org/20230803230323.1478869-1-andrew.cooper3@citrix.com ]
Fixes: dc5723b02e ("kbuild: add support for Clang LTO")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230711091952.27944-2-petr.pavlu@suse.com
Help differentiate the two remote related "serial" struct variables by
renaming "wacom_remote_data" to "wacom_remote_work_data".
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'connected' variable was poorly named, and this has led to some
confusion. We can get the same information by checking if a serial number
exists in the specified EKR slot.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 9f1015d45f ("HID: wacom: EKR: attach the power_supply on first connection")
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously would let led_classdev handle renaming when name collision
occurred. Now that an ID allocator is used to uniquely identify multiple
Thunderstrike controllers, generate unique led device names.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use power supply API to expose battery information about connected
Thunderstrike controllers to the system. Provide information on battery
capacity, charge status, charger type, voltage, and temperature.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid calling thunderstrike_led_set_brightness from thunderstrike_create
when led_classdev_unregister is called. led_classdev_unregister was called
from thunderstrike_create in the error path. Calling
thunderstrike_led_set_brightness in this situation is unsafe.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The __mx25_clocks_init function always returns 0 and its only
caller does not check the return value. Let's remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-3-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Print the imx25 silicon revision when the clocks are initialised.
Use the same mechanism as for imx27, i.e. call mx25_revision.
This function is unused at the moment.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-2-martin@kaiser.cx
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add a hid-google-stadiaff module to support rumble based force feedback
on the Google Stadia controller. This works using the HID output
endpoint exposed on both the USB and BLE interface.
Signed-off-by: Fabio Baltieri <fabiobaltieri@chromium.org>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The lightspeed receiver for the Pro X Superlight uses 13 byte mouse reports
without a report id. The workaround for such cases has been adjusted to
handle these larger packets.
The device now reports the status of its battery in wireless mode and
libratbag now recognizes the device and it can be configured with Piper.
https://github.com/libratbag/libratbag/pull/1122
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the Pro X Superlight over wired USB.
The device now reports the status of its battery.
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hardware don't have a SAI4 instance so remove the define. Use a
comment to keep it as reference and to avoid confusion.
Fixes: 1088691447 ("dt-bindings: imx: Add clock binding doc for i.MX8MP")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. Following the changes to pllv4,
use the new type IMX_PLLV4_IMX8ULP_1GHZ.
Fixes: c43a801a57 ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. According to RM, the MULT is
using a range from 27 to 54, not some fixed values. If using
current PLL implementation, some clock rate can't be supported.
Fix the issue by adding new type for the SPLL2 and use MULT range
to replace MULT table
Fixes: 5f0601c47c ("clk: imx: Update the pllv4 to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Skip the srso cmd line parsing which is not needed on Zen1/2 with SMT
disabled and with the proper microcode applied (latter should be the
case anyway) as those are not affected.
Fixes: 5a15d83488 ("x86/srso: Tie SBPB bit setting to microcode patch detection")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230813104517.3346-1-bp@alien8.de
The Audio Clock Mux (ACM) is a collection of control registers
and multiplexers that are used to route the audio source clocks
to the audio peripherals.
Each audio peripheral has its dedicated audio clock mux
(which differ based on usage) and control register.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.
Add the clockid for clocks in header file.
The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add support for the Steelseries Arctis 1 XBox headset. This driver
will export the battery information from the headset, as well as the
"wireless_status" property.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When connecting the Trackpad 1 via any bluetooth adapter, the device
disconnects whenever the battery level is queried. It reconnects
again after a few seconds, but it's an incredibly jarring experience
since it will just cut out in the middle of mouse operations.
This patch ignores querying the battery and avoids disconnects.
This bug is reported here:
- https://bugzilla.kernel.org/show_bug.cgi?id=204589
- https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1834085
It looks like a similar approach (disabling battery checking)
was also suggested for the Apple Magic Mouse before a custom
driver was created:
https://bugzilla.kernel.org/show_bug.cgi?id=103631
Signed-off-by: Nimish Gåtam <nimishg@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the driver core allows for struct class to be in read-only
memory, making all 'class' structures to be declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the driver core allows for struct class to be in read-only
memory, making all 'class' structures to be declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Stefan Achatz <erazor_de@users.sourceforge.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As per the upstream "hidpp" helpers commit:
"
There has been some confusion about error value 5 but feature specs that
refer to it generally use NOT_ALLOWED.
"
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: 80c3fecfcd
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size of 'struct hid_input'
from 72 to 64 bytes.
It saves a few bytes of memory and is more cache-line friendly.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230705065313.67043-8-frank.li@vivo.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Some digitizers (notably XP-Pen Artist 24) do not report the Invert
usage when erasing. This causes the device to be permanently stuck with
the BTN_TOOL_RUBBER tool after sending Eraser, as Invert is the only
usage that can release the tool. In this state, Touch and Inrange are
no longer reported to userspace, rendering the pen unusable.
Prior to commit 87562fcd13 ("HID: input: remove the need for
HID_QUIRK_INVERT"), BTN_TOOL_RUBBER was never set and Eraser events were
simply translated into BTN_TOUCH without causing an inconsistent state.
Introduce HID_QUIRK_NOINVERT for such digitizers and detect them during
hidinput_configure_usage(). This quirk causes the tool to be released
as soon as Eraser is reported as not set. Set BTN_TOOL_RUBBER in
input->keybit when mapping Eraser.
Fixes: 87562fcd13 ("HID: input: remove the need for HID_QUIRK_INVERT")
Co-developed-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Illia Ostapyshyn <ostapyshyn@sra.uni-hannover.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch removes the error checking for debugfs_create_file
in hid-wiimote-debug.c.c. This is because the debugfs_create_file()
does not return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_file:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L451
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Reviewed-by: David Rheinsberg <david@readahead.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Lenovo Yoga C630 has a combined keyboard and accelerometer that
interfaces via i2c-hid. Currently this laptop either has a working
keyboard (if CONFIG_HID_SENSOR_HUB is disabled) or a working accelerometer.
only works on kernels. Put another way, most distro kernels enable
CONFIG_HID_SENSOR_HUB and therefore cannot work on this device since the
keyboard doesn't work!
Fix this by providing a richer connect mask during the probe. With this
change both keyboard and screen orientation sensors work correctly.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Initially, it was thought that doing an innocuous division in the #DE
handler would take care to prevent any leaking of old data from the
divider but by the time the fault is raised, the speculation has already
advanced too far and such data could already have been used by younger
operations.
Therefore, do the innocuous division on every exit to userspace so that
userspace doesn't see any potentially old data from integer divisions in
kernel space.
Do the same before VMRUN too, to protect host data from leaking into the
guest too.
Fixes: 77245f1c3c ("x86/CPU/AMD: Do not leak quotient data after a division by 0")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230811213824.10025-1-bp@alien8.de
Use LEA instead of ADD when adjusting %rsp in srso_safe_ret{,_alias}()
so as to avoid clobbering flags. Drop one of the INT3 instructions to
account for the LEA consuming one more byte than the ADD.
KVM's emulator makes indirect calls into a jump table of sorts, where
the destination of each call is a small blob of code that performs fast
emulation by executing the target instruction with fixed operands.
E.g. to emulate ADC, fastop() invokes adcb_al_dl():
adcb_al_dl:
<+0>: adc %dl,%al
<+2>: jmp <__x86_return_thunk>
A major motivation for doing fast emulation is to leverage the CPU to
handle consumption and manipulation of arithmetic flags, i.e. RFLAGS is
both an input and output to the target of the call. fastop() collects
the RFLAGS result by pushing RFLAGS onto the stack and popping them back
into a variable (held in %rdi in this case):
asm("push %[flags]; popf; " CALL_NOSPEC " ; pushf; pop %[flags]\n"
<+71>: mov 0xc0(%r8),%rdx
<+78>: mov 0x100(%r8),%rcx
<+85>: push %rdi
<+86>: popf
<+87>: call *%rsi
<+89>: nop
<+90>: nop
<+91>: nop
<+92>: pushf
<+93>: pop %rdi
and then propagating the arithmetic flags into the vCPU's emulator state:
ctxt->eflags = (ctxt->eflags & ~EFLAGS_MASK) | (flags & EFLAGS_MASK);
<+64>: and $0xfffffffffffff72a,%r9
<+94>: and $0x8d5,%edi
<+109>: or %rdi,%r9
<+122>: mov %r9,0x10(%r8)
The failures can be most easily reproduced by running the "emulator"
test in KVM-Unit-Tests.
If you're feeling a bit of deja vu, see commit b63f20a778
("x86/retpoline: Don't clobber RFLAGS during CALL_NOSPEC on i386").
In addition, this breaks booting of clang-compiled guest on
a gcc-compiled host where the host contains the %rsp-modifying SRSO
mitigations.
[ bp: Massage commit message, extend, remove addresses. ]
Fixes: fb3bd914b3 ("x86/srso: Add a Speculative RAS Overflow mitigation")
Closes: https://lore.kernel.org/all/de474347-122d-54cd-eabf-9dcc95ab9eae@amd.com
Reported-by: Srikanth Aithal <sraithal@amd.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20230810013334.GA5354@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/r/20230811155255.250835-1-seanjc@google.com
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove MAINTAINERS
entry for OXNAS files.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20230814-topic-oxnas-upstream-remove-v3-3-e2ba579a49d3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, mark the
OX810 and OX820 IRQ compatible as deprecated.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230814-topic-oxnas-upstream-remove-v3-2-e2ba579a49d3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for OX810 and OX820 IRQ controller.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20230814-topic-oxnas-upstream-remove-v3-1-e2ba579a49d3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
For the TLB_PTLOCK checks we used an optimization to store the spc
register into the spinlock to unlock it. This optimization works as
long as the lightweight spinlock checks (CONFIG_LIGHTWEIGHT_SPINLOCK_CHECK)
aren't enabled, because they really check if the lock word is zero or
__ARCH_SPIN_LOCK_UNLOCKED_VAL and abort with a kernel crash
("Spinlock was trashed") otherwise.
Drop that optimization to make it possible to activate both checks
at the same time.
Noticed-by: Sam James <sam@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Sam James <sam@gentoo.org>
Cc: stable@vger.kernel.org # v6.4+
Fixes: 15e64ef652 ("parisc: Add lightweight spinlock checks")
The PSGMII interface is similar to QSGMII. The main difference
is that the PSGMII interface combines five SGMII lines into a
single link while in QSGMII only four lines are combined.
Similarly to the QSGMII, this interface mode might also needs
special handling within the MAC driver.
It is commonly used by Qualcomm with their QCA807x PHY series and
modern WiSoC-s.
Add definitions for the PHY layer to allow to express this type
of connection between the MAC and PHY.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new PSGMII mode which is similar to QSGMII with the difference being
that it combines 5 SGMII lines into a single link compared to 4 on QSGMII.
It is commonly used by Qualcomm on their QCA807x PHY series.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
mlxsw: Support traffic redirection from a locked bridge port
Ido Schimmel writes:
It is possible to add a filter that redirects traffic from the ingress
of a bridge port that is locked (i.e., performs security / SMAC lookup)
and has learning enabled. For example:
# ip link add name br0 type bridge
# ip link set dev swp1 master br0
# bridge link set dev swp1 learning on locked on mab on
# tc qdisc add dev swp1 clsact
# tc filter add dev swp1 ingress pref 1 proto ip flower skip_sw src_ip 192.0.2.1 action mirred egress redirect dev swp2
In the kernel's Rx path, this filter is evaluated before the Rx handler
of the bridge, which means that redirected traffic should not be
affected by bridge port configuration such as learning.
However, the hardware data path is a bit different and the redirect
action (FORWARDING_ACTION in hardware) merely attaches a pointer to the
packet, which is later used by the L2 lookup stage to understand how to
forward the packet. Between both stages - ingress ACL and L2 lookup -
learning and security lookup are performed, which means that redirected
traffic is affected by bridge port configuration, unlike in the kernel's
data path.
The learning discrepancy was handled in commit 577fa14d21 ("mlxsw:
spectrum: Do not process learned records with a dummy FID") by simply
ignoring learning notifications generated by the redirected traffic. A
similar solution is not possible for the security / SMAC lookup since
- unlike learning - the CPU is not involved and packets that failed the
lookup are dropped by the device.
Instead, solve this by prepending the ignore action to the redirect
action and use it to instruct the device to disable both learning and
the security / SMAC lookup for redirected traffic.
Patch #1 adds the ignore action.
Patch #2 prepends the action to the redirect action in flower offload
code.
Patch #3 removes the workaround in commit 577fa14d21 ("mlxsw:
spectrum: Do not process learned records with a dummy FID") since it is
no longer needed.
Patch #4 adds a test case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that traffic can be redirected from a locked bridge port and that
it does not create locked FDB entries.
Cc: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous patch, with the ignore action prepended to
the redirect action, it is not longer possible for redirected traffic to
generate learning notifications.
Therefore, remove the workaround that was added in commit 577fa14d21
("mlxsw: spectrum: Do not process learned records with a dummy FID") as
it is no longer needed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to add a filter that redirects traffic from the ingress
of a bridge port that is locked (i.e., performs security / SMAC lookup)
and has learning enabled. For example:
# ip link add name br0 type bridge
# ip link set dev swp1 master br0
# bridge link set dev swp1 learning on locked on mab on
# tc qdisc add dev swp1 clsact
# tc filter add dev swp1 ingress pref 1 proto ip flower skip_sw src_ip 192.0.2.1 action mirred egress redirect dev swp2
In the kernel's Rx path, this filter is evaluated before the Rx handler
of the bridge, which means that redirected traffic should not be
affected by bridge port configuration such as learning.
However, the hardware data path is a bit different and the redirect
action (FORWARDING_ACTION in hardware) merely attaches a pointer to the
packet, which is later used by the L2 lookup stage to understand how to
forward the packet. Between both stages - ingress ACL and L2 lookup -
learning and security lookup are performed, which means that redirected
traffic is affected by bridge port configuration, unlike in the kernel's
data path.
The learning discrepancy was handled in commit 577fa14d21 ("mlxsw:
spectrum: Do not process learned records with a dummy FID") by simply
ignoring learning notifications generated by the redirected traffic. A
similar solution is not possible for the security / SMAC lookup since
- unlike learning - the CPU is not involved and packets that failed the
lookup are dropped by the device.
Instead, solve this by prepending the ignore action to the redirect
action and use it to instruct the device to disable both learning and
the security / SMAC lookup for redirected traffic.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IGNORE_ACTION which is used to ignore basic switching functions
such as learning on a per-packet basis.
The action will be prepended to the FORWARDING_ACTION in subsequent
patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Show TSSTSSEL(Timestamp System Time Source),
ADDMACADRSEL(additional MAC addresses), SMASEL(SMA/MDIO Interface),
HDSEL(Half-duplex Support) in debugfs.
2. Show exact number of additional MAC address registers for XGMAC2 core.
3. XGMAC2 core does not have different IP checksum offload types, so just
show rx_coe instead of rx_coe_type1 or rx_coe_type2.
4. XGMAC2 core does not have rxfifo_over_2048 definition, skip it.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Zetao says:
====================
Use helper functions to update stats
The patch set uses the helper functions dev_sw_netstats_rx_add() and
dev_sw_netstats_tx_add() to update stats, which is the same as
implementing the function separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
