- The switch to using iomap for executing direct synchronous write to
sequential files using zone append BIO overlooked cases where the BIO
built by iomap is too large and needs splitting, which is not allowed
with zone append. Fix this by using regular write commands instead.
The use of zone append commands will be reintroduces later with
proper support from iomap.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZNbIugAKCRDdoc3SxdoY
dgGZAQCJWVBGXP/FAB4o7ifuqZ9xDjcf0RyrYrcS1N+kV1REqgD/ZnHXxAbNJNtx
A3A5W7bFQJogNp/gWR7K7/jt1cRNwgo=
=nlBY
-----END PGP SIGNATURE-----
Merge tag 'zonefs-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fix from Damien Le Moal:
- The switch to using iomap for executing a direct synchronous write to
sequential files using a zone append BIO overlooked cases where the
BIO built by iomap is too large and needs splitting, which is not
allowed with zone append.
Fix this by using regular write commands instead. The use of zone
append commands will be reintroduced later with proper support from
iomap.
* tag 'zonefs-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: fix synchronous direct writes to sequential files
Tony Nguyen says:
====================
i40e: Replace one-element arrays with flexible-array members
Replace one-element arrays with flexible-array members in multiple
structures.
This results in no differences in binary output.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: Replace one-element array with flex-array member in struct i40e_profile_aq_section
i40e: Replace one-element array with flex-array member in struct i40e_section_table
i40e: Replace one-element array with flex-array member in struct i40e_profile_segment
i40e: Replace one-element array with flex-array member in struct i40e_package_header
====================
Link: https://lore.kernel.org/r/20230810175302.1964182-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The init function is only referenced locally, so it should be static to
avoid this warning:
drivers/net/ethernet/amd/atarilance.c:370:28: error: no previous prototype for 'atarilance_probe' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230810122528.1220434-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function is exported for no reason and should just be static:
drivers/net/ethernet/sun/ldmvsw.c:127:5: error: no previous prototype for 'ldmvsw_open' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20230810122528.1220434-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The patch which made it to the kernel somehow changed the
match condition from
DMI_MATCH(DMI_PRODUCT_NAME, "UPX-TGL01")
to
DMI_MATCH(DMI_PRODUCT_VERSION, "UPX-TGL")
Revert back to the correct match condition to disable the
interrupt mode on the board.
Cc: stable@vger.kernel.org # v6.4+
Fixes: edb13d7bb0 ("tpm: tpm_tis: Disable interrupts *only* for AEON UPX-i11")
Link: https://lore.kernel.org/lkml/20230524085844.11580-1-peter.ujfalusi@linux.intel.com/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Fixed all CHECK: Alignment should match open parenthesis
as reported by checkpatch to adhere to the Linux kernel
coding-style guidelines.
Signed-off-by: Alexon Oliveira <alexondunkan@gmail.com>
Link: https://lore.kernel.org/r/ZNO6HohffQlbh7jn@alolivei-thinkpadt480s.gru.csb
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
issues, or are not considered suitable for -stable backporting.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZNad/gAKCRDdBJ7gKXxA
jmw6AP9u6k8XcS8ec3/u0IUEuh7ckHx5Vvjfmo5YgWlIJDeWegD9G2fh3ZJgcjMO
jMssklfXmP+QSijCIxUva1TlzwtPDAQ=
=MqiN
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-08-11-13-44' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"14 hotfixes. 11 of these are cc:stable and the remainder address
post-6.4 issues, or are not considered suitable for -stable
backporting"
* tag 'mm-hotfixes-stable-2023-08-11-13-44' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/damon/core: initialize damo_filter->list from damos_new_filter()
nilfs2: fix use-after-free of nilfs_root in dirtying inodes via iput
selftests: cgroup: fix test_kmem_basic false positives
fs/proc/kcore: reinstate bounce buffer for KCORE_TEXT regions
MAINTAINERS: add maple tree mailing list
mm: compaction: fix endless looping over same migrate block
selftests: mm: ksm: fix incorrect evaluation of parameter
hugetlb: do not clear hugetlb dtor until allocating vmemmap
mm: memory-failure: avoid false hwpoison page mapped error info
mm: memory-failure: fix potential unexpected return value from unpoison_memory()
mm/swapfile: fix wrong swap entry type for hwpoisoned swapcache page
radix tree test suite: fix incorrect allocation size for pthreads
crypto, cifs: fix error handling in extract_iter_to_sg()
zsmalloc: fix races between modifications of fullness and isolated
This patch is intended as a proof-of-concept for the new SBRM
machinery[1]. For some brief background, the idea behind SBRM is using
the __cleanup__ attribute to automatically unlock locks (or otherwise
release resources) when they go out of scope, similar to C++ style RAII.
This promises some benefits such as making code simpler (particularly
where you have lots of goto fail; type constructs) as well as reducing
the surface area for certain kinds of bugs.
The changes in this patch should not result in any difference in how the
code actually runs (i.e., it's purely an exercise in this new syntax
sugar). In one instance SBRM was not appropriate, so I left that part
alone, but all other locking/unlocking is handled automatically in this
patch.
[1] https://lore.kernel.org/all/20230626125726.GU4253@hirez.programming.kicks-ass.net/
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: "Mitchell Levy (Microsoft)" <levymitchell0@gmail.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230807-sbrm-hyperv-v2-1-9d2ac15305bd@gmail.com
Add basic support for the AM62P5 SK with UART console and
ramdisk as rootfs.
Schematics is at https://www.ti.com/lit/zip/sprr487
Signed-off-by: Bryan Brattlof <bb@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230811184432.732215-4-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The AM62Px is an extension of the existing Sitara AM62x low-cost family
of application processors built for Automotive and Linux Application
development. Scalable Arm Cortex-A53 performance and embedded features,
such as: multi high-definition display support, 3D-graphics
acceleration, 4K video acceleration, and extensive peripherals make the
AM62Px well-suited for a broad range of automation and industrial
application, including automotive digital instrumentation, automotive
displays, industrial HMI, and more.
Some highlights of AM62P SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Dual/Single core variants are provided in the same package to allow HW
compatible designs.
* One Device manager Cortext-R5F for system power and resource
management, and one Cortex-R5F for Functional Safety or
general-purpose usage.
* One 3D GPU up to 50 GLFOPS
* H.264/H.265 Video Encode/Decode.
* Display support: 3x display support over OLDI/LVDS (1x OLDI-DL, 1x or
2x OLDI-SL), DSI, or DPI. Up to 3840x1080@60fps resolution
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1xCSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized Hardware Security Module with support for secure
boot, debug security and crypto acceleration and trusted execution
environment.
* One 32-bit DDR Subsystem that supports LPDDR4, DDR4 memory types.
* Multiple low power modes support, ex: Deep sleep, Standby, MCU-only,
enabling battery powered system design.
For those interested, more details about this SoC can be found in the
Technical Reference Manual here:
https://www.ti.com/lit/pdf/spruj83
Signed-off-by: Bryan Brattlof <bb@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230811184432.732215-3-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds JTAG ID info for the AM62PX so as to enable SoC detection in
kernel.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20230811170127.250733-1-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
wkup_i2c0, mcu_uart0, main_uart8, main_sdhci0 and main_sdhci1 are required
for bootloader operation on TI K3 AM69-SK EVM. These IPs along with
pinmuxes need to be marked for all bootloader phases, hence add bootph-all
to these nodes in kernel dts.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230811192030.3480616-4-a-nandan@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
wkup_i2c0, mcu_uart0, main_uart8, fss, ospi0, ospi1, main_sdhci0 and
main_sdhci1 are required for bootloader operation on TI K3 J784S4 EVM.
These IPs along with pinmuxes need to be marked for all bootloader phases,
hence add bootph-all to these nodes in kernel dts.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230811192030.3480616-3-a-nandan@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
On TI K3 J784S4 SoC, only secure_proxy_mcu and secure_proxy_sa3 nodes are
exclusively used by R5 bootloader, rest of the dts nodes with bootph-* are
used by later boot stages also.
And secure_proxy_mcu and secure_proxy_sa3 are disabled in kernel device
tree, and will be only enabled in R5 bootloader device tree.
So, bootph-pre-ram for secure_proxy_mcu and secure_proxy_sa3 will be
added in R5 bootloader device tree only.
Add bootph-all for all other nodes that are used in the bootloader on
K3 J784S4 SoC, and bootph-pre-ram is not needed specifically for any node
in kernel dts.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230811192030.3480616-2-a-nandan@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit
522b1d6921 ("x86/cpu/amd: Add a Zenbleed fix")
provided a fix for the Zen2 VZEROUPPER data corruption bug affecting
a range of CPU models, but the AMD Custom APU 0405 found on SteamDeck
was not listed, although it is clearly affected by the vulnerability.
Add this CPU variant to the Zenbleed erratum list, in order to
unconditionally enable the fallback fix until a proper microcode update
is available.
Fixes: 522b1d6921 ("x86/cpu/amd: Add a Zenbleed fix")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230811203705.1699914-1-cristian.ciocaltea@collabora.com
Enable CONFIG_DRM_ITE_IT66121.
ILITEK ITE-IT66121 is an HDMI transmitter, which takes parallel video
signals (DPI) as input. It is being used on TI's AM625 SoC based
BeaglePlay platform[0].
[0]: https://beagleboard.org/play
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-7-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (ITE-IT66121) on the BeaglePlay platform. For audio output,
BeaglePlay uses mcasp1.
Add pinmux info for DSS DPI signals.
Further, add support for HDMI audio and video output.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-6-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable audio output over HDMI instead of the 3.5mm jack.
A FET switch (U65) on the EVM muxes serial audio lines coming from McASP
between the codec (tlv320aic3106) and the HDMI bridge (sii9022).
By default it uses the codec, but it can be toggled to use the HDMI
bridge by shorting a (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
[a-bhatia1: Cosmetic changes]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-5-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM625 SK and AM62-LP SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-4-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add Display SubSystem (DSS) DT node for the AM625 SoC.
The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). It outputs OLDI signals on one video port (VP1) and
DPI signals on another (VP2). The video ports are connected to the
pipelines via 2 identical overlay managers (ovr1 and ovr2).
Also add the DT node for DSS clock divider. This is a fixed-factor-clock
and does not have any register. This comes into effect whenenver OLDI
display is used. The input to this divider is a serial clock used by
OLDI TXes. The divider divides the input clock by 7, and provides the
pixel clock to VP1.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-3-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Display Data Channel (DDC) transactions between an HDMI transmitter
(SIL9022A in this case) and an HDMI monitor, occur at a maximum of
100KHz. That's the maximum supported frequency within DDC standards.
While the SIL9022A can transact with the core at 400KHz, it needs to
drop the frequency to 100KHz when communicating with the monitor,
otherwise, the i2c controller times out and shows warning like this.
[ 985.773431] omap_i2c 20010000.i2c: controller timed out
That feature, however, has not been enabled in the SIL9022 driver.
Since, dropping the frequency doesn't affect any other devices on the
bus, drop the main-i2c1 frequency from 400KHz to 100KHz.
Fixes: a841581451 ("arm64: dts: ti: Refractor AM625 SK dts")
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-2-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Making virt_to_pfn() a static inline taking a strongly typed
(const void *) makes the contract of a passing a pointer of that
type to the function explicit and exposes any misuse of the
macro virt_to_pfn() acting polymorphic and accepting many types
such as (void *), (unitptr_t) or (unsigned long) as arguments
without warnings.
For symmetry, do the same with pfn_to_virt().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Adding the full list of VMID's, which are used by different clients to
pass to the secure world.
Signed-off-by: Gokul krishna Krishnakumar <quic_gokukris@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230403204455.6758-1-quic_gokukris@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that the driver core allows for struct class to be in read-only
memory, move the ilo_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230810194239.26892-1-ivan.orlov0322@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the class_genwqe structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time. Update the 'class_genwqe' field of the
'genwqe_dev' struct correspondingly.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230810182711.22664-1-ivan.orlov0322@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the helper function devm_kmemdup() rather than duplicating its
implementation, which helps to enhance code readability.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230810115049.2104099-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WinSystems WS16C48 I/O address region spans offsets 0x0 through 0xA,
which is a total of 11 bytes. Fix the WS16C48_EXTENT define to the
correct value of 11 so that access to necessary device registers is
properly requested in the ws16c48_probe() callback by the
devm_request_region() function call.
Fixes: 2c05a0f29f ("gpio: ws16c48: Implement and utilize register structures")
Cc: stable@vger.kernel.org
Cc: Paul Demetrotion <pdemetrotion@winsystems.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Rework the handling of interrupt overrides on AMD Zen-based machines to
avoid recently introduced regressions (Hans de Goede).
-----BEGIN PGP SIGNATURE-----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=4kD6
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Rework the handling of interrupt overrides on AMD Zen-based machines
to avoid recently introduced regressions (Hans de Goede).
Note that this is intended as a short-term mitigation for 6.5 and the
long-term approach will be to attempt to use the configuration left by
the BIOS, but it requires more investigation"
* tag 'acpi-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Add IRQ override quirk for PCSpecialist Elimina Pro 16 M
ACPI: resource: Honor MADT INT_SRC_OVR settings for IRQ1 on AMD Zen
ACPI: resource: Always use MADT override IRQ settings for all legacy non i8042 IRQs
ACPI: resource: revert "Remove "Zen" specific match and quirks"
========
Core
----
- Skipped MHI reset if the device is in RDDM EE (Ramdump mode) since the device
cannot process reset request.
- Updated the sysfs contact details to use MHI list instead of bouncing
codeaurora email ids.
- Added support to allow MHI client drivers to provide the device firmware via
a pointer. This is required to support new firmware format to be used by
ath11k drivers.
- Used vcalloc instead of vzalloc to protect against multiplication overflows.
- Removed decrementing one unused parameter.
pci_generic
-----------
- Added support for MHI SW channels (IP_SW0) so that the host can transfer data
from devices over networking interface through this specific channel.
- Added support for a clone of Quectel RM520N-GL modem which uses a different
PID as it is targeted for laptop usecase.
- Added support for a clone of Quectel EM160R-GL modem which uses a different
PID as it is targeted for laptop usecase.
- Added support for another clone of Quectel RM520N-GL modem which uses a
different PID as it is targeted for Lenovo laptop usecase.
- Added support for Dell DW5932e modem (both eSIM and non-eSIM variants).
- Added support for Telit FE990 modem.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAmTWUx0ACgkQVZ8R5v6R
zvXwRAf/XqcFqz4hcOgfWOiPyv1suIlkH+DCNGL5E6911uW+IoEeRdig/G8rzriX
VyGlnN94HL2BfdmFQO7J2tsuSZOMUvvo0QgtT4Dhu5ft/tP2QR7fmJ87XjCwn50Y
EboUN4cIBGVY73i5XeqrZsVvLDhXLVIhGh7LKAexigs+Ye/nCwaC6NW9qkO7brpK
/mtR86px7/+p+Eidmgjb7rq61Nww35UIplr/nAJatWr9NckCG5ytS9zGUIdvP+0q
wq6AdKEhDWkWfJEVkgKfxZkOdtJCW0AMrJUuTJq5T/FdsKzL8+lrsHbfFK+i/rXh
S+/rr0uPOiFHUqAPXpZVha8dgB8Njg==
=EUC3
-----END PGP SIGNATURE-----
Merge tag 'mhi-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI Host
========
Core
----
- Skipped MHI reset if the device is in RDDM EE (Ramdump mode) since the device
cannot process reset request.
- Updated the sysfs contact details to use MHI list instead of bouncing
codeaurora email ids.
- Added support to allow MHI client drivers to provide the device firmware via
a pointer. This is required to support new firmware format to be used by
ath11k drivers.
- Used vcalloc instead of vzalloc to protect against multiplication overflows.
- Removed decrementing one unused parameter.
pci_generic
-----------
- Added support for MHI SW channels (IP_SW0) so that the host can transfer data
from devices over networking interface through this specific channel.
- Added support for a clone of Quectel RM520N-GL modem which uses a different
PID as it is targeted for laptop usecase.
- Added support for a clone of Quectel EM160R-GL modem which uses a different
PID as it is targeted for laptop usecase.
- Added support for another clone of Quectel RM520N-GL modem which uses a
different PID as it is targeted for Lenovo laptop usecase.
- Added support for Dell DW5932e modem (both eSIM and non-eSIM variants).
- Added support for Telit FE990 modem.
* tag 'mhi-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: pci_generic: add support for Telit FE990 modem
bus: mhi: host: remove unused-but-set parameter
bus: mhi: host: pci_generic: Add support for Quectel RM520N-GL Lenovo variant
bus: mhi: host: allow MHI client drivers to provide the firmware via a pointer
docs: ABI: sysfs-bus-mhi: Update contact info
bus: mhi: host: use vmalloc_array and vcalloc
bus: mhi: host: pci_generic: Add support for Dell DW5932e
bus: mhi: host: pci_generic: Add support for Quectel RM520N-GL modem
bus: mhi: host: pci_generic: Add support for Quectel EM160R-GL modem
bus: mhi: host: pci_generic: Add support for IP_SW0 channels
bus: mhi: host: Skip MHI reset if device is in RDDM
Testing that a device is not currently in a low power state provides no
guarantees that the device is not imminently transitioning to such a state.
Increment the PM usage counter before accessing the device. Since we don't
wish to wake the device for PME polling, do so only if the device is
already active by using pm_runtime_get_if_active().
Link: https://lore.kernel.org/r/20230803171233.3810944-3-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Make amd-pstate use device_attributes as expected by the CPU root
kobject (Thomas Weißschuh).
- Restore the previous behavior of resume_store() when hibernation is
not available which is to return the full number of bytes that were
to be written by user space (Vlastimil Babka).
-----BEGIN PGP SIGNATURE-----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=0RaA
-----END PGP SIGNATURE-----
Merge tag 'pm-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an amd-pstate cpufreq driver issues and recently introduced
hibernation-related breakage.
Specifics:
- Make amd-pstate use device_attributes as expected by the CPU root
kobject (Thomas Weißschuh)
- Restore the previous behavior of resume_store() when hibernation is
not available which is to return the full number of bytes that were
to be written by user space (Vlastimil Babka)"
* tag 'pm-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: amd-pstate: fix global sysfs attribute type
PM: hibernate: fix resume_store() return value when hibernation not available
New device support
* adi,ad8366
- Add support for the HMC792 digital attenuator (mostly chip specific data)
* alwinner,sun20i-gpadc
- New driver for the integrated ADC on a number of allwinner SoCs
including dt-binding documentation.
* microchip,mcp4728
- New driver for this quad channel DAC. Includes dt-bindings.
* miramems, da280
- Add ID for DA217 accelerometer which is compatible with the da280.
* murata,irs-d200
- New driver for this passive infrared sensor typically used for human
detection. Includes bindings and a few pieces of new ABI to
cover a case of needing to count a number of repeats of an event
before reporting it.
* rohm,bu27008
- Add initial support for the BU27010 RGB + flickering sensor to this
driver. Substantial refactoring was needed to enable this.
Features
* adi,admv8818
- Add mode that bypasses the input and output filters.
* amlogic,meson
- Support control of the MUX on channel 7, exposed as multiple channels.
- Support channel labels.
* sensirion,scd4x
- Add pressure compensation. Controlled via an 'output' pressure channel.
* ti,lmp92040
- Add IIO buffered supported (read via chrdev).
* vishay,vcnl4000
- Add proximity interrupt support for vcnl4200.
- Add proximity integration time control for vcnl4200.
- Add illuminance integration time control for vcnl4040 and vcnl4200.
- Add calibration bias, proximity and illuminance event period, and
oversampling ratio control for vcnl4040 and vncl4200.
Cleanup and minor fixes
* core
- Tidy up handling of set_trigger_state() callback return values
to consistently assume no positive return values.
- Use min() rather than min_t() in a case where types were clearly
the same.
- Drop some else statements that follow continue with a loop or
a returns.
- White space and comment format cleanup.
- Use sysfs_match_string() helper to improve readability.
- Use krealloc_array() to make it explicit a krealloc is for an array
of structures, not just one.
* tools
- Tidy up potential overflow in array index.
* tree wide
- Fix up includes for DT related headers.
- Drop some error prints in places where as similar error message
is printed by the function being called.
- Tidy up handling of return value from platform_get_irq() to no longer
take into account 0 as a value that might be returned. Similar for
fwnode_irq_get().
* adi,ad7192
- Add missing error check and improved debug logging.
- Use sysfs_emit_at() rather than open coded variant.
* adi,adis16475
- Drop unused scan element enum entries.
- Specify that a few more devices support burst32 mode.
* adi,admv1013
- Enable all required regulators and document as required in the
dt-binding.
* adi,admv1014
- Make all regulators required in the dt-binding as the device needs
them all enabled.
* adi,adxl313
- Fix wrong enum values being used in the i2c_device_id table.
- Use i2c_get_match_data() to reduce open coded handling of the
various id tables.
* allwinner,gpadc
- Make the kconfig text more specific to make space for separate drivers
for other Allwinner devices.
* amlogic,meson
- Drop unused timestamp channels as no buffer support.
- Various minor reorganizations to enable addition of support channel 7
MUX.
- Initialize some default values to account for potential previous user
since reboot.
* qcom,spmi-adc5
- Add ADC5_GPIO2_100K_PU support to driver to line up with bindings.
* qcom,spmi-adc7
- Use predefined channel ID definitions rather than values.
* invensense, common
- Factor out the timestamp handling to a module used by both mpu6050 and
icm42600.
* invensense,mpu6050
- Read as many FIFO elements as possible in one bus access.
* men,s188
- Drop redundant initialization of driver owner field.
* microchip,mcp4018 and mcp4531
- Use i2c_get_match_data() instead of open coding. Includes making the
data format the same for the i2c_device_id and firmware match
tables.
* semtech,sx9310
- dt-bindings: Add reference to IIO schema to provide the label property.
* semtech,sx9324
- dt-bindings: Add reference to IIO schema to provide the label property.
* st,stm32-adc
- Use devm_platform_get_and_ioremap_resource() instead of open coded
version.
* st,stm-lptimer-trigger
- Drop setting platform drvdata as it wasn't then used.
* ti,ads1015
- Fix wrong dt binding description of ti,datarate for some devices.
* vishay,vcnl4200
- Move to switch statements for channel type checking to make later
additions simpler.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmTTydERHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Foj9sw//QDch/sLMb1bEiJTHDwECuSgm+jWth8gi
CdG3GQerBU2U+eQkf2jgG73HhfHccanKWGAHfkdOLSblcFWJL6Q+MSJCNu4J3kGY
2XUkdazXMXRbfqoq3vqnC4u6mEMXGTpq8JZoAz7XXCs8GcW/loyqV2E54cbQJxCJ
KSqCWIhoWAU7/PQkgOJLBnDirMt+rEwUObifG4PJcOYIPq17qS+XhpMVPydNfYgg
3PJ+jK4Gg6cZsI3lW7vaBoLvzYRn+Ri2vVc2ZnwyLI/y9rEJPjt4aXt9FZbw10Eg
S/7twD1Ns5n8X6IS3VFA4A4ITu0VFX3pjOg9WLEpkqRJqLt1n2R9pcnTkD6x4a0r
6LZvmLij9R6ozPZKlalncyOPZamnEcIxyqyuqcEEFDAF6/Mf+VznwBQM8HDhQ/CO
3OAGkNprtXIvKAz/xiGx9r8z8d5Gt1lD+vclcDcf6U8YwEkMWrc95EVIumcNOkG2
qNESgzDvOh92aHpKfwrsHproNKcKbtm9he1BrN5u28G+UBA1jsPg15hmYVkv/Hd3
v6tgvkxVSn2xS94K2BhqjLzOgXgl4EmbSewg5AfPVNYM1RZrMLJvBky1/81JJmsD
565dcF/vE3/hguFX5lCOKGTxT88pwFNHth26ypAOXuwhUNz+jxp9NJ0Adn/IR8Kp
hA/SfjALiDA=
=hTrR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.6
New device support
* adi,ad8366
- Add support for the HMC792 digital attenuator (mostly chip specific data)
* alwinner,sun20i-gpadc
- New driver for the integrated ADC on a number of allwinner SoCs
including dt-binding documentation.
* microchip,mcp4728
- New driver for this quad channel DAC. Includes dt-bindings.
* miramems, da280
- Add ID for DA217 accelerometer which is compatible with the da280.
* murata,irs-d200
- New driver for this passive infrared sensor typically used for human
detection. Includes bindings and a few pieces of new ABI to
cover a case of needing to count a number of repeats of an event
before reporting it.
* rohm,bu27008
- Add initial support for the BU27010 RGB + flickering sensor to this
driver. Substantial refactoring was needed to enable this.
Features
* adi,admv8818
- Add mode that bypasses the input and output filters.
* amlogic,meson
- Support control of the MUX on channel 7, exposed as multiple channels.
- Support channel labels.
* sensirion,scd4x
- Add pressure compensation. Controlled via an 'output' pressure channel.
* ti,lmp92040
- Add IIO buffered supported (read via chrdev).
* vishay,vcnl4000
- Add proximity interrupt support for vcnl4200.
- Add proximity integration time control for vcnl4200.
- Add illuminance integration time control for vcnl4040 and vcnl4200.
- Add calibration bias, proximity and illuminance event period, and
oversampling ratio control for vcnl4040 and vncl4200.
Cleanup and minor fixes
* core
- Tidy up handling of set_trigger_state() callback return values
to consistently assume no positive return values.
- Use min() rather than min_t() in a case where types were clearly
the same.
- Drop some else statements that follow continue with a loop or
a returns.
- White space and comment format cleanup.
- Use sysfs_match_string() helper to improve readability.
- Use krealloc_array() to make it explicit a krealloc is for an array
of structures, not just one.
* tools
- Tidy up potential overflow in array index.
* tree wide
- Fix up includes for DT related headers.
- Drop some error prints in places where as similar error message
is printed by the function being called.
- Tidy up handling of return value from platform_get_irq() to no longer
take into account 0 as a value that might be returned. Similar for
fwnode_irq_get().
* adi,ad7192
- Add missing error check and improved debug logging.
- Use sysfs_emit_at() rather than open coded variant.
* adi,adis16475
- Drop unused scan element enum entries.
- Specify that a few more devices support burst32 mode.
* adi,admv1013
- Enable all required regulators and document as required in the
dt-binding.
* adi,admv1014
- Make all regulators required in the dt-binding as the device needs
them all enabled.
* adi,adxl313
- Fix wrong enum values being used in the i2c_device_id table.
- Use i2c_get_match_data() to reduce open coded handling of the
various id tables.
* allwinner,gpadc
- Make the kconfig text more specific to make space for separate drivers
for other Allwinner devices.
* amlogic,meson
- Drop unused timestamp channels as no buffer support.
- Various minor reorganizations to enable addition of support channel 7
MUX.
- Initialize some default values to account for potential previous user
since reboot.
* qcom,spmi-adc5
- Add ADC5_GPIO2_100K_PU support to driver to line up with bindings.
* qcom,spmi-adc7
- Use predefined channel ID definitions rather than values.
* invensense, common
- Factor out the timestamp handling to a module used by both mpu6050 and
icm42600.
* invensense,mpu6050
- Read as many FIFO elements as possible in one bus access.
* men,s188
- Drop redundant initialization of driver owner field.
* microchip,mcp4018 and mcp4531
- Use i2c_get_match_data() instead of open coding. Includes making the
data format the same for the i2c_device_id and firmware match
tables.
* semtech,sx9310
- dt-bindings: Add reference to IIO schema to provide the label property.
* semtech,sx9324
- dt-bindings: Add reference to IIO schema to provide the label property.
* st,stm32-adc
- Use devm_platform_get_and_ioremap_resource() instead of open coded
version.
* st,stm-lptimer-trigger
- Drop setting platform drvdata as it wasn't then used.
* ti,ads1015
- Fix wrong dt binding description of ti,datarate for some devices.
* vishay,vcnl4200
- Move to switch statements for channel type checking to make later
additions simpler.
* tag 'iio-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (73 commits)
Documentation: ABI: testing: admv8818: add bypass
drivers: iio: filter: admv8818: add bypass mode
iio: light: bd27008: Support BD27010 RGB
iio: light: bu27008: add chip info
dt-bindings: iio: ROHM BU27010 RGBC + flickering sensor
iio: add MCP4728 I2C DAC driver
dt-bindings: iio: dac: add mcp4728.yaml
drivers: iio: admv1013: add vcc regulators
dt-bindings: iio: admv1013: add vcc regulators
iio: trigger: stm32-lptimer-trigger: remove unneeded platform_set_drvdata()
iio: adc: men_z188_adc: Remove redundant initialization owner in men_z188_driver
dt-bindings: iio: admv1014: make all regs required
iio: cdc: ad7150: relax return value check for IRQ get
iio: mb1232: relax return value check for IRQ get
iio: adc: fix the return value handle for platform_get_irq()
tools: iio: iio_generic_buffer: Fix some integer type and calculation
iio: potentiometer: mcp4531: Use i2c_get_match_data()
iio: potentiometer: mcp4018: Use i2c_get_match_data()
iio: core: Fix issues and style of the comments
iio: core: Switch to krealloc_array()
...
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d8376 ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike default access to config space through sysfs, the VPD read and write
functions don't actively manage the runtime power management state of the
device during access. Since commit 7ab5e10eda ("vfio/pci: Move the
unused device into low power state with runtime PM"), the vfio-pci driver
will use runtime power management and release unused devices to make use of
low power states. Attempting to access VPD information in D3cold can
result in incorrect information or kernel crashes depending on the system
behavior.
Wrap the VPD read/write bin attribute handlers in runtime PM and take into
account the potential quirk to select the correct device to wake.
Link: https://lore.kernel.org/r/20230803171233.3810944-2-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[bhelgaas: tweak pci_dev_put() test to match the pci_get_func0_dev() test]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In commit 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux"), the UAF
problem is not completely fixed. There is a race condition in
gsm_cleanup_mux(), which caused this UAF.
The UAF problem is triggered by the following race:
task[5046] task[5054]
----------------------- -----------------------
gsm_cleanup_mux();
dlci = gsm->dlci[0];
mutex_lock(&gsm->mutex);
gsm_cleanup_mux();
dlci = gsm->dlci[0]; //Didn't take the lock
gsm_dlci_release(gsm->dlci[i]);
gsm->dlci[i] = NULL;
mutex_unlock(&gsm->mutex);
mutex_lock(&gsm->mutex);
dlci->dead = true; //UAF
Fix it by assigning values after mutex_lock().
Link: https://syzkaller.appspot.com/text?tag=CrashReport&x=176188b5a80000
Cc: stable <stable@kernel.org>
Fixes: 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Fixes: aa371e96f0 ("tty: n_gsm: fix restart handling via CLD command")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Signed-off-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Link: https://lore.kernel.org/r/20230811031121.153237-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=+1Vt
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fixes for request_queue state (Ming)
- Another uuid quirk (August)
- RCU poll fix for NVMe (Ming)
- Fix for an IO stall with polled IO (me)
- Fix for blk-iocost stats enable/disable accounting (Chengming)
- Regression fix for large pages for zram (Christoph)
* tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux:
nvme: core: don't hold rcu read lock in nvme_ns_chr_uring_cmd_iopoll
blk-iocost: fix queue stats accounting
block: don't make REQ_POLLED imply REQ_NOWAIT
block: get rid of unused plug->nowait flag
zram: take device and not only bvec offset into account
nvme-pci: add NVME_QUIRK_BOGUS_NID for Samsung PM9B1 256G and 512G
nvme-rdma: fix potential unbalanced freeze & unfreeze
nvme-tcp: fix potential unbalanced freeze & unfreeze
nvme: fix possible hang when removing a controller during error recovery
len and remain can never be negative in gdm_tty_write(). So remove such
a check and move the check of remaining bytes to the loop condition.
This way, the preceding 'if' is now superfluous too. Fix all that and
make the code cleaner.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: linux-staging@lists.linux.dev
Link: https://lore.kernel.org/r/20230810103900.19353-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the type of tty_operations::write() counters with the 'count'
parameter. I.e. use size_t for them.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20230810091510.13006-37-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for two more variables in hso_serial_write(). Switch to
min_t() and eliminate those.
Furthermore, the 'if-goto' is superfluous as memcpy() of zero count is a
nop. So is addition of zero. So remove the 'if-goto' completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20230810091510.13006-36-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the type of tty_operations::write() counters with the 'count'
parameter. I.e. use size_t for them.
This includes changing constants to UL to keep min() and avoid min_t().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: linux-staging@lists.linux.dev
Link: https://lore.kernel.org/r/20230810091510.13006-35-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the type of tty_operations::write() counters with the 'count'
parameter. I.e. use size_t for them.
This includes changing vcc_port::chars_in_buffer to size_t to keep min()
and avoid min_t().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Link: https://lore.kernel.org/r/20230810091510.13006-34-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
