This error path needs call mutex_unlock(&ocelot->tas_lock) before
returning.
Fixes: 2d800bc500 ("net/sched: taprio: replace tc_taprio_qopt_offload :: enable with a "cmd" enum")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
rfs: annotate lockless accesses
rfs runs without locks held, so we should annotate
read and writes to shared variables.
It should prevent compilers forcing writes
in the following situation:
if (var != val)
var = val;
A compiler could indeed simply avoid the conditional:
var = val;
This matters if var is shared between many cpus.
v2: aligns one closing bracket (Simon)
adds Fixes: tags (Jakub)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add READ_ONCE()/WRITE_ONCE() on accesses to the sock flow table.
This also prevents a (smart ?) compiler to remove the condition in:
if (table->ents[index] != newval)
table->ents[index] = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add READ_ONCE()/WRITE_ONCE() on accesses to sk->sk_rxhash.
This also prevents a (smart ?) compiler to remove the condition in:
if (sk->sk_rxhash != newval)
sk->sk_rxhash = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detlev Casanova says:
====================
net: phy: realtek: Support external PHY clock
Some PHYs can use an external clock that must be enabled before
communicating with them.
Changes since v3:
* Do not call genphy_suspend if WoL is enabled.
Changes since v2:
* Reword documentation commit message
Changes since v1:
* Remove the clock name as it is not guaranteed to be identical across
different PHYs
* Disable/Enable the clock when suspending/resuming
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.
The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethern PHYs can have external an clock that needs to be activated before
communicating with the PHY.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the PHY can use an external clock source instead of a
crystal.
Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the size of rx indirection table dynamically in netvsc
from the value of size provided by OID_GEN_RECEIVE_SCALE_CAPABILITIES
query instead of using a constant value of ITAB_NUM.
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Tested-on: Ubuntu22 (azure VM, SKU size: Standard_F72s_v2)
Testcases:
1. ethtool -x eth0 output
2. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-Synthetic
3. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-SRIOV
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
etm4_remove_dev() returned zero unconditionally. Make it return void
instead, which makes it clear in the callers that there is no error to
handle. Simplify etm4_remove_platform_dev() accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230518201629.260672-1-u.kleine-koenig@pengutronix.de
Drivers should be silent when they work correctly. There's no reason to
emit info messages when GPIO lines are hogged. Demote the message to
debug.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Suggested-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Offloaded policies are deleted through two flows: netdev is going
down and policy flush.
In both cases, the code lacks relevant call to delete offloaded policy.
Fixes: 919e43fad5 ("xfrm: add an interface to offload policy")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently lock_two_nondirectories() is skipping any passed directories.
After vfs_rename() uses lock_two_inodes(), all the remaining four users
of this function pass only regular files to it. So drop the somewhat
unusual "skip directory" logic and instead warn if anybody passes
directory to it. This also allows us to use lock_two_inodes() in
lock_two_nondirectories() to concentrate the lock ordering logic in less
places.
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230601105830.13168-6-jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Replace these open-code bearer rcu_dereference access with bearer_get(),
like other places in bearer.c. While at it, also use tipc_net() instead
of net_generic(net, tipc_net_id) to get "tn" in bearer.c.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/1072588a8691f970bda950c7e2834d1f2983f58e.1685976044.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fixes to debugfs registration
- Fix use-after-free in hci_remove_ltk/hci_remove_irk
- Fixes to ISO channel support
- Fix missing checks for invalid L2CAP DCID
- Fix l2cap_disconnect_req deadlock
- Add lock to protect HCI_UNREGISTER
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmR+ftMZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKQMXD/9NcuqbGmEzJspVA8bZ8gXD
L7a68QnacdIoqH56QstLhGPQsYH6dv9fwhpNX6AN8/j8UG8DnDXQtHyfm4gZzfYA
h8GP7+ZQIEiHivIxiamrJnQ1Ii+KYEV3NGyS43YBuuPi9LcTFR0Km42xA0GqOnDU
Hz3/n5v342479TjJPNJkFPmcUGViRaLXtKhzcBzmSykUW+SVuIuD03yxuAJcojf5
rlPYA7yho7k8BAWkcYxWAP3v9fzQVa3nz8rQO2rG+poi4La2mmqRHykuSCXmzvBX
SbZwvzqgquqgQiFLpRIo/nwnVwPu3NYK6dQzlXPqiaxfM6qAtRttwQWNnOT+UxEu
VVGk6fD9iKjo9dttq+lTSY3LI/SXWAHYByIBzjx883hJYf1YvDAMSlMlzo029xL6
BHu3hMTDhosP8sG5wFdR2KzBmUd1W/ZcwOG0UP8PjshZgrOZ3uej9p3MrocKAys7
uGOBFmGzwOaQLXJQLbd4djE5l6zLOxSCV/0OLIWQw7VFQiHb66NzN6wenYEkDnxM
j2pFAlzp4RKHHCjU3dfaE90c0ede116e9nhjAlzmUOxggg6aCxCrCkMNOI8NlZ4v
oukYWq66RWYA/J4S80OLepITtBRPVn3JFxOXss5xESFfEnzL2nRZ5gm8jJJGULU4
x6tKTHaomO99FcH0ZFlZMw==
=jMWO
-----END PGP SIGNATURE-----
Merge tag 'for-net-2023-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fixes to debugfs registration
- Fix use-after-free in hci_remove_ltk/hci_remove_irk
- Fixes to ISO channel support
- Fix missing checks for invalid L2CAP DCID
- Fix l2cap_disconnect_req deadlock
- Add lock to protect HCI_UNREGISTER
* tag 'for-net-2023-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Add missing checks for invalid DCID
Bluetooth: ISO: use correct CIS order in Set CIG Parameters event
Bluetooth: ISO: don't try to remove CIG if there are bound CIS left
Bluetooth: Fix l2cap_disconnect_req deadlock
Bluetooth: hci_qca: fix debugfs registration
Bluetooth: fix debugfs registration
Bluetooth: hci_sync: add lock to protect HCI_UNREGISTER
Bluetooth: Fix use-after-free in hci_remove_ltk/hci_remove_irk
Bluetooth: ISO: Fix CIG auto-allocation to select configurable CIG
Bluetooth: ISO: consider right CIS when removing CIG at cleanup
====================
Link: https://lore.kernel.org/r/20230606003454.2392552-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit a78418e6a0 ("block: Always initialize bio IO priority on
submit"), bio->bi_ioprio will never be IOPRIO_CLASS_NONE when calling
blkcg_set_ioprio(), so there will be no way to promote the io-priority
of one cgroup to IOPRIO_CLASS_RT, because bi_ioprio will always be
greater than or equals to IOPRIO_CLASS_RT.
It seems possible to call blkcg_set_ioprio() first then try to
initialize bi_ioprio later in bio_set_ioprio(), but this doesn't work
for bio in which bi_ioprio is already initialized (e.g., direct-io), so
introduce a new promote-to-rt policy to promote the iopriority of bio to
IOPRIO_CLASS_RT if the ioprio is not already RT.
For none-to-rt policy, although it doesn't work now, but considering
that its purpose was also to override the io-priority to RT and allowing
for a smoother transition, just keep it and treat it as an alias of
the promote-to-rt policy.
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20230428074404.280532-1-houtao@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=tb7S
-----END PGP SIGNATURE-----
Merge tag 'nf-23-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing nul-check in basechain hook netlink dump path, from Gavrilov Ilia.
2) Fix bitwise register tracking, from Jeremy Sowden.
3) Null pointer dereference when accessing conntrack helper,
from Tijs Van Buggenhout.
4) Add schedule point to ipset's call_ad, from Kuniyuki Iwashima.
5) Incorrect boundary check when building chain blob.
* tag 'nf-23-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: out-of-bound check in chain blob
netfilter: ipset: Add schedule point in call_ad().
netfilter: conntrack: fix NULL pointer dereference in nf_confirm_cthelper
netfilter: nft_bitwise: fix register tracking
netfilter: nf_tables: Add null check for nla_nest_start_noflag() in nft_dump_basechain_hook()
====================
Link: https://lore.kernel.org/r/20230606225851.67394-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both rtw88 and rtw89 have a 802.11 powersave fix for a regression
introduced in v6.0. mt76 fixes a race and a null pointer dereference.
iwlwifi fixes an issue where not enough memory was allocated for a
firmware event. And finally the stack has several smaller fixes all
over.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmR/S2URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuHXwgAhS9w8UIZ2qLYmLQOlby4Hx9+TV2lSdZ1
V878SCWC+/nRX1mRrWZdU5zwwXXVpLv61dCUOuYyJp8ko4izzTwUhZzvNGowaGgo
HA+KrND/rZ2ApRZDZQMpe8SXaTUZJhcRDdV4njjdeSqNEcfksgz1W8exzDpKt8YD
pAdz8+gfpBSoATRThY5p3vyeC4e1weKqbsk96SLoip/wKzz92jyUx9fyexTskfoN
WMfDU474bz4XIEXzmuFBqpwylwxTvy+FKvEVZfe9PqtXEOChqMUZGGMAemD81FY0
kKIEY21kAOBKRBW5OLNHcR0WrFcq+C17+L9eazE1F7iQiKIVQaCsag==
=a4jg
-----END PGP SIGNATURE-----
Merge tag 'wireless-2023-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.4
Both rtw88 and rtw89 have a 802.11 powersave fix for a regression
introduced in v6.0. mt76 fixes a race and a null pointer dereference.
iwlwifi fixes an issue where not enough memory was allocated for a
firmware event. And finally the stack has several smaller fixes all
over.
* tag 'wireless-2023-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: fix locking in regulatory disconnect
wifi: cfg80211: fix locking in sched scan stop work
wifi: iwlwifi: mvm: Fix -Warray-bounds bug in iwl_mvm_wait_d3_notif()
wifi: mac80211: fix switch count in EMA beacons
wifi: mac80211: don't translate beacon/presp addrs
wifi: mac80211: mlme: fix non-inheritence element
wifi: cfg80211: reject bad AP MLD address
wifi: mac80211: use correct iftype HE cap
wifi: mt76: mt7996: fix possible NULL pointer dereference in mt7996_mac_write_txwi()
wifi: rtw89: remove redundant check of entering LPS
wifi: rtw89: correct PS calculation for SUPPORTS_DYNAMIC_PS
wifi: rtw88: correct PS calculation for SUPPORTS_DYNAMIC_PS
wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll
====================
Link: https://lore.kernel.org/r/20230606150817.EC133C433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault says:
====================
ipv4: Remove RT_CONN_FLAGS() calls in flowi4_init_output().
Remove a few RT_CONN_FLAGS() calls used inside flowi4_init_output().
These users can be easily converted to set the scope properly, instead
of overloading the tos parameter with scope information as done by
RT_CONN_FLAGS().
The objective is to eventually remove RT_CONN_FLAGS() entirely, which
will then allow to also remove RTO_ONLINK and to finally convert
->flowi4_tos to dscp_t.
====================
Link: https://lore.kernel.org/r/cover.1685999117.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RT_CONN_FLAGS(sk) overloads flowi4_tos with the RTO_ONLINK bit when
sk has the SOCK_LOCALROUTE flag set. This allows
ip_route_output_key_hash() to eventually adjust flowi4_scope.
Instead of relying on special handling of the RTO_ONLINK bit, we can
just set the route scope correctly. This will eventually allow to avoid
special interpretation of tos variables and to convert ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RT_CONN_FLAGS(sk) overloads the tos parameter with the RTO_ONLINK bit
when sk has the SOCK_LOCALROUTE flag set. This is only useful for
ip_route_output_key_hash() to eventually adjust the route scope.
Let's drop RTO_ONLINK and set the correct scope directly to avoid this
special case in the future and to allow converting ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 699b045a8e ("net: virtio_net: notifications coalescing
support") added coalescing command support for virtio_net. However,
the coalesce commands are using buffers on the stack, which is causing
the device to see DMA errors. There should also be a complaint from
check_for_stack() in debug_dma_map_xyz(). Fix this by adding and using
coalesce params from the control_buf struct, which aligns with other
commands.
Cc: stable@vger.kernel.org
Fixes: 699b045a8e ("net: virtio_net: notifications coalescing support")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Allen Hubbe <allen.hubbe@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20230605195925.51625-1-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 523847df1b ("pds_core: add devcmd device interfaces") included
initial support for FW recovery detection. Unfortunately, the ordering
in pdsc_is_fw_good() was incorrect, which was causing FW recovery to be
undetected by the driver. Fix this by making sure to update the cached
fw_status by calling pdsc_is_fw_running() before setting the local FW
gen.
Fixes: 523847df1b ("pds_core: add devcmd device interfaces")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230605195116.49653-1-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Robert Hancock says:
====================
Move KSZ9477 errata handling to PHY driver
Patches to move handling for KSZ9477 PHY errata register fixes from
the DSA switch driver into the corresponding PHY driver, for more
proper layering and ordering.
====================
Link: https://lore.kernel.org/r/20230605153943.1060444-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.
This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.
The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We missed that tcp_gso_segment() was assuming skb->len was smaller than 65535 :
oldlen = (u16)~skb->len;
This part came with commit 0718bcc09b ("[NET]: Fix CHECKSUM_HW GSO problems.")
This leads to wrong TCP checksum.
Adapt the code to accept arbitrary packet length.
v2:
- use two csum_add() instead of csum_fold() (Alexander Duyck)
- Change delta type to __wsum to reduce casts (Alexander Duyck)
Fixes: 09f3d1a3a5 ("ipv6/gso: remove temporary HBH/jumbo header")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230605161647.3624428-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If it is async, runqueue_node is freed in g2d_runqueue_worker on another
worker thread. So in extreme cases, if g2d_runqueue_worker runs first, and
then executes the following if statement, there will be use-after-free.
Signed-off-by: Min Li <lm0963hack@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix a wrong error return by dropping an error return.
When vidi driver is remvoed, if ctx->raw_edid isn't same as fake_edid_info
then only what we have to is to free ctx->raw_edid so that driver removing
can work correctly - it's not an error case.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
A remote DoS vulnerability of RPL Source Routing is assigned CVE-2023-2156.
The Source Routing Header (SRH) has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. Addresses[1..n] .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The originator of an SRH places the first hop's IPv6 address in the IPv6
header's IPv6 Destination Address and the second hop's IPv6 address as
the first address in Addresses[1..n].
The CmprI and CmprE fields indicate the number of prefix octets that are
shared with the IPv6 Destination Address. When CmprI or CmprE is not 0,
Addresses[1..n] are compressed as follows:
1..n-1 : (16 - CmprI) bytes
n : (16 - CmprE) bytes
Segments Left indicates the number of route segments remaining. When the
value is not zero, the SRH is forwarded to the next hop. Its address
is extracted from Addresses[n - Segment Left + 1] and swapped with IPv6
Destination Address.
When Segment Left is greater than or equal to 2, the size of SRH is not
changed because Addresses[1..n-1] are decompressed and recompressed with
CmprI.
OTOH, when Segment Left changes from 1 to 0, the new SRH could have a
different size because Addresses[1..n-1] are decompressed with CmprI and
recompressed with CmprE.
Let's say CmprI is 15 and CmprE is 0. When we receive SRH with Segment
Left >= 2, Addresses[1..n-1] have 1 byte for each, and Addresses[n] has
16 bytes. When Segment Left is 1, Addresses[1..n-1] is decompressed to
16 bytes and not recompressed. Finally, the new SRH will need more room
in the header, and the size is (16 - 1) * (n - 1) bytes.
Here the max value of n is 255 as Segment Left is u8, so in the worst case,
we have to allocate 3825 bytes in the skb headroom. However, now we only
allocate a small fixed buffer that is IPV6_RPL_SRH_WORST_SWAP_SIZE (16 + 7
bytes). If the decompressed size overflows the room, skb_push() hits BUG()
below [0].
Instead of allocating the fixed buffer for every packet, let's allocate
enough headroom only when we receive SRH with Segment Left 1.
[0]:
skbuff: skb_under_panic: text:ffffffff81c9f6e2 len:576 put:576 head:ffff8880070b5180 data:ffff8880070b4fb0 tail:0x70 end:0x140 dev:lo
kernel BUG at net/core/skbuff.c:200!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 154 Comm: python3 Not tainted 6.4.0-rc4-00190-gc308e9ec0047 #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:skb_panic (net/core/skbuff.c:200)
Code: 4f 70 50 8b 87 bc 00 00 00 50 8b 87 b8 00 00 00 50 ff b7 c8 00 00 00 4c 8b 8f c0 00 00 00 48 c7 c7 80 6e 77 82 e8 ad 8b 60 ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90
RSP: 0018:ffffc90000003da0 EFLAGS: 00000246
RAX: 0000000000000085 RBX: ffff8880058a6600 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88807dc1c540 RDI: ffff88807dc1c540
RBP: ffffc90000003e48 R08: ffffffff82b392c8 R09: 00000000ffffdfff
R10: ffffffff82a592e0 R11: ffffffff82b092e0 R12: ffff888005b1c800
R13: ffff8880070b51b8 R14: ffff888005b1ca18 R15: ffff8880070b5190
FS: 00007f4539f0b740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055670baf3000 CR3: 0000000005b0e000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<IRQ>
skb_push (net/core/skbuff.c:210)
ipv6_rthdr_rcv (./include/linux/skbuff.h:2880 net/ipv6/exthdrs.c:634 net/ipv6/exthdrs.c:718)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5))
ip6_input_finish (./include/linux/rcupdate.h:805 net/ipv6/ip6_input.c:483)
__netif_receive_skb_one_core (net/core/dev.c:5494)
process_backlog (./include/linux/rcupdate.h:805 net/core/dev.c:5934)
__napi_poll (net/core/dev.c:6496)
net_rx_action (net/core/dev.c:6565 net/core/dev.c:6696)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572)
do_softirq (kernel/softirq.c:472 kernel/softirq.c:459)
</IRQ>
<TASK>
__local_bh_enable_ip (kernel/softirq.c:396)
__dev_queue_xmit (net/core/dev.c:4272)
ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:134)
rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914)
sock_sendmsg (net/socket.c:724 net/socket.c:747)
__sys_sendto (net/socket.c:2144)
__x64_sys_sendto (net/socket.c:2156 net/socket.c:2152 net/socket.c:2152)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7f453a138aea
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffcc212a1c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007ffcc212a288 RCX: 00007f453a138aea
RDX: 0000000000000060 RSI: 00007f4539084c20 RDI: 0000000000000003
RBP: 00007f4538308e80 R08: 00007ffcc212a300 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f4539712d1b
</TASK>
Modules linked in:
Fixes: 8610c7c6e3 ("net: ipv6: add support for rpl sr exthdr")
Reported-by: Max VA
Closes: https://www.interruptlabs.co.uk/articles/linux-ipv6-route-of-death
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230605180617.67284-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The drm sched entity must be flushed before finishing, to account for
jobs potentially still in flight at that time.
Lima did not do this flush until now, so switch the destroy call to the
drm_sched_entity_destroy() wrapper which will take care of that.
This fixes a regression on lima which started since the rework in
commit 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
where some specific types of applications may hang indefinitely.
Fixes: 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606143247.433018-1-nunes.erico@gmail.com
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it
and drop unnecessary ranges property.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Working on the code gen for C reveals typos in the ethtool spec
as the compiler tries to find the names in the existing uAPI
header. Fix the mistakes.
Fixes: a353318ebf ("tools: ynl: populate most of the ethtool spec")
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20230605233257.843977-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPUID leaf 0x80000022 i.e. ExtPerfMonAndDbg advertises some new
performance monitoring features for AMD processors.
Bit 0 of EAX indicates support for Performance Monitoring Version 2
(PerfMonV2) features. If found to be set during PMU initialization,
the EBX bits of the same CPUID function can be used to determine
the number of available PMCs for different PMU types.
Expose the relevant bits via KVM_GET_SUPPORTED_CPUID so that
guests can make use of the PerfMonV2 features.
Co-developed-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230603011058.1038821-13-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
If AMD Performance Monitoring Version 2 (PerfMonV2) is detected by
the guest, it can use a new scheme to manage the Core PMCs using the
new global control and status registers.
In addition to benefiting from the PerfMonV2 functionality in the same
way as the host (higher precision), the guest also can reduce the number
of vm-exits by lowering the total number of MSRs accesses.
In terms of implementation details, amd_is_valid_msr() is resurrected
since three newly added MSRs could not be mapped to one vPMC.
The possibility of emulating PerfMonV2 on the mainframe has also
been eliminated for reasons of precision.
Co-developed-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: drop "Based on the observed HW." comments]
Link: https://lore.kernel.org/r/20230603011058.1038821-12-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a KVM-only leaf for AMD's PerfMonV2 to redirect the kernel's scattered
version to its architectural location, e.g. so that KVM can query guest
support via guest_cpuid_has().
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: massage changelog]
Link: https://lore.kernel.org/r/20230603011058.1038821-11-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Cap the number of general purpose counters enumerated on AMD to what KVM
actually supports, i.e. don't allow userspace to coerce KVM into thinking
there are more counters than actually exist, e.g. by enumerating
X86_FEATURE_PERFCTR_CORE in guest CPUID when its not supported.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: massage changelog]
Link: https://lore.kernel.org/r/20230603011058.1038821-10-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Enable and advertise PERFCTR_CORE if and only if the minimum number of
required counters are available, i.e. if perf says there are less than six
general purpose counters.
Opportunistically, use kvm_cpu_cap_check_and_set() instead of open coding
the check for host support.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: massage shortlog and changelog]
Link: https://lore.kernel.org/r/20230603011058.1038821-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Disable PMU support when running on AMD and perf reports fewer than four
general purpose counters. All AMD PMUs must define at least four counters
due to AMD's legacy architecture hardcoding the number of counters
without providing a way to enumerate the number of counters to software,
e.g. from AMD's APM:
The legacy architecture defines four performance counters (PerfCtrn)
and corresponding event-select registers (PerfEvtSeln).
Virtualizing fewer than four counters can lead to guest instability as
software expects four counters to be available. Rather than bleed AMD
details into the common code, just define a const unsigned int and
provide a convenient location to document why Intel and AMD have different
mins (in particular, AMD's lack of any way to enumerate less than four
counters to the guest).
Keep the minimum number of counters at Intel at one, even though old P6
and Core Solo/Duo processor effectively require a minimum of two counters.
KVM can, and more importantly has up until this point, supported a vPMU so
long as the CPU has at least one counter. Perf's support for P6/Core CPUs
does require two counters, but perf will happily chug along with a single
counter when running on a modern CPU.
Cc: Jim Mattson <jmattson@google.com>
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: set Intel min to '1', not '2']
Link: https://lore.kernel.org/r/20230603011058.1038821-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add an explicit !enable_pmu check as relying on kvm_pmu_cap to be
zeroed isn't obvious. Although when !enable_pmu, KVM will have
zero-padded kvm_pmu_cap to do subsequent CPUID leaf assignments.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230603011058.1038821-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Move the Intel PMU implementation of pmc_is_enabled() to common x86 code
as pmc_is_globally_enabled(), and drop AMD's implementation. AMD PMU
currently supports only v1, and thus not PERF_GLOBAL_CONTROL, thus the
semantics for AMD are unchanged. And when support for AMD PMU v2 comes
along, the common behavior will also Just Work.
Signed-off-by: Like Xu <likexu@tencent.com>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20230603011058.1038821-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Move the handling of GLOBAL_CTRL, GLOBAL_STATUS, and GLOBAL_OVF_CTRL,
a.k.a. GLOBAL_STATUS_RESET, from Intel PMU code to generic x86 PMU code.
AMD PerfMonV2 defines three registers that have the same semantics as
Intel's variants, just with different names and indices. Conveniently,
since KVM virtualizes GLOBAL_CTRL on Intel only for PMU v2 and above, and
AMD's version shows up in v2, KVM can use common code for the existence
check as well.
Signed-off-by: Like Xu <likexu@tencent.com>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20230603011058.1038821-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reject userspace writes to MSR_CORE_PERF_GLOBAL_STATUS that attempt to set
reserved bits. Allowing userspace to stuff reserved bits doesn't harm KVM
itself, but it's architecturally wrong and the guest can't clear the
unsupported bits, e.g. makes the guest's PMI handler very confused.
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: rewrite changelog to avoid use of #GP, rebase on name change]
Link: https://lore.kernel.org/r/20230603011058.1038821-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Move reprogram_counters() out of Intel specific PMU code and into pmu.h so
that it can be used to implement AMD PMU v2 support.
No functional change intended.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: rewrite changelog]
Link: https://lore.kernel.org/r/20230603011058.1038821-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Rename global_ovf_ctrl_mask to global_status_mask to avoid confusion now
that Intel has renamed GLOBAL_OVF_CTRL to GLOBAL_STATUS_RESET in PMU v4.
GLOBAL_OVF_CTRL and GLOBAL_STATUS_RESET are the same MSR index, i.e. are
just different names for the same thing, but the SDM provides different
entries in the IA-32 Architectural MSRs table, which gets really confusing
when looking at PMU v4 definitions since it *looks* like GLOBAL_STATUS has
bits that don't exist in GLOBAL_OVF_CTRL, but in reality the bits are
simply defined in the GLOBAL_STATUS_RESET entry.
No functional change intended.
Cc: Like Xu <like.xu.linux@gmail.com>
Link: https://lore.kernel.org/r/20230603011058.1038821-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
