Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Commit e91a4d5deb ("dt-bindings: leds: Document commonly used
LED triggers") introduced a enum match for cpu, while a pattern
'^cpu[0-9]*$' already exists.
This causes linux,default-trigger = "cpu" to have more than one match
and generates the following dtbs_check warning:
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dtb: leds: led-2:linux,default-trigger: More than one condition true in oneOf schema:
{'$ref': '/schemas/types.yaml#/definitions/string',
'oneOf': [{'items': [{'enum': ['backlight',
'default-on',
'heartbeat',
'disk-activity',
'disk-read',
'disk-write',
'timer',
'pattern',
'audio-micmute',
'audio-mute',
'bluetooth-power',
'cpu',
'flash',
'kbd-capslock',
'mtd',
'nand-disk',
'none',
'torch',
'usb-gadget',
'usb-host',
'usbport']}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^cpu[0-9]*$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^hci[0-9]+-power$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^mmc[0-9]+$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^phy[0-9]+tx$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'}]}
Drop the explicit match against cpu since the pattern match already
covers the same.
Fixes: e91a4d5deb ("dt-bindings: leds: Document commonly used LED triggers")
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230424151437.256073-1-nm@ti.com
Document support for the pmi632, often found with the sdm632 SoC.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-5-98bafa909c36@z3ntu.xyz
The PMI632 PMIC contains 5 PWM channels, 3 of which can be used for
LEDs.
For the LED pattern it doesn't have LUT like other PMICs but uses SDAM
instead. This is not currently implemented in the driver but since LPG
works fine without it, add support for the PMIC now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-4-98bafa909c36@z3ntu.xyz
Document the availability of an LPG configuration for the PMI632 PMIC in
the Qualcomm Light Pulse Generator driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-3-98bafa909c36@z3ntu.xyz
The LP55xx range of devices have an internal charge pump which
can (automatically) increase the output voltage towards the
LED's, boosting the output voltage to 4.5V.
Implement this option from the devicetree. When the setting
is not present it will operate in automatic mode as before.
Tested on LP55231. Datasheet analysis shows that LP5521, LP5523
and LP8501 are identical in topology and are modified in the
same way.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-3-maarten.zanders@mind.be
Add a binding to configure the internal charge pump for lp55xx.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-2-maarten.zanders@mind.be
If CONFIG_DEBUG_FS is not set:
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f8bb6e113359ddfab7b59e4d4274bd4c06d6d0a.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of failure, debugfs_create_dir() does not return NULL, but an
error pointer. Most incorrect error checks were fixed, but the one in
create_regulator() was forgotten.
Fix the remaining error check.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ee980a108b5854dd8ce3630f8f673e784e057d17.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed523 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
Tegra20 can do horizontal and vertical image flip, but Tegra210 cannot
(either the hardware, or this driver).
In preparation to adding Tegra20 support, add a flag in struct tegra_vi_soc
so the generic vi.c code knows whether the flip controls should be added or
not.
Also provide a generic implementation that simply sets two flags in the
channel struct. The Tegra20 implementation will enable flipping at stream
start based on those flags.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tegra20 supports planar YUV422 capture, which can be implemented by writing
U and V base address registers in addition to the "main" base buffer
address register.
It also supports H and V flip, which among others requires to write the
start address (i.e. the 1st offset to write, at the end of the buffer or
line) in more registers for Y and, for planar formats, U and V.
Add minimal hooks in VI to allow per-SoC optional support to those
features:
- variables in struct tegra_vi for the U and V buffer base offsets
- variables in struct tegra_vi for the Y, U and V buffer start offsets
- an optional per-soc VI operation to compute those values on queue setup
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In preparation to implement Tegra20 parallel video capture, add a variable
to hold the required syncpt and document all the syncpt variables.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_channel_host1x_syncpt_init() gets the host1x syncpts needed for the
Tegra210 implementation, and tegra_channel_host1x_syncpts_free() puts
them.
Tegra20 needs to get and put a different syncpt. In preparation for adding
Tegra20 support, move these functions to new ops in the soc-specific
`struct tegra_vi_ops` .
No functional changes.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Tegra20 VI needs an additional operation to enable the VI, add an
operation for that.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The CSI module does not handle all the MIPI lane calibration procedure,
leaving a small part of it to the VI module. In doing this,
tegra_channel_enable_stream() (vi.c) manipulates the private data of the
upstream subdev casting it to struct 'tegra_csi_channel', which will be
wrong after introducing a VIP (parallel video input) channel.
This prevents adding support for the VIP module. It also breaks the
logical isolation between modules.
Since the lane calibration requirement does not exist in the parallel input
module, moving the calibration function to a per-module op is not
optimal. Instead move the calibration procedure in the CSI module, together
with the rest of the calibration procedures. After this change,
tegra_channel_enable_stream() just calls v4l2_subdev_call() to ask for a
stream start/stop to the CSI module, which in turn knows all the
CSI-specific details to implement it.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The tegra_default_format in vi.c is specific to Tegra210 CSI.
In preparation for adding Tegra20 VIP support, move the default format to a
new field in the soc-specific `struct tegra_vi_soc`. Instead of an entire
format struct, only store a pointer to an item in the existing format
array.
No functional changes. The format pointed to is the same that used to be in
vi.c.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_channel_fmt_align() takes care of the size constraints, alignment and
rounding requirements of the Tegra210 VI peripheral. Tegra20 has different
constraints.
In preparation for adding Tegra20 support, move this function to a new op
in the soc-specific `struct tegra_vi_ops` .
Also move to tegra210.c the T210-specific defines used in the moved code.
No functional changes.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We are about to add support for the Tegra20 parallel video capture, which
has no TPG. In preparation for that, limit the VIDEO_TEGRA_TPG option to
Tegra210 which is the only implementation currently provided by this
driver.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is only a pointer reference to struct tegra_vi in video.h, thus vi.h
is not needed.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This declaration is used only in csi.c, no need to export it elsewhere.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct tegra_vi_graph_entity is an internal implementation detail of the VI
module. Move its declaration from vi.h to vi.c.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_node_put(node) does nothing if node == NULL, so it can be moved to the
cleanup section at the bottom.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_vi_channels_alloc() can primarily fail for two reasons:
1. "ports" node not found
2. port_num > vi->soc->vi_max_channels
Case 1 prints nothing, case 2 has a dev_err(). The caller [tegra_vi_init()]
has a generic dev_err() on any failure. This mean that in case 2 we print
two messages, and in case 1 we only print a generic message.
Remove the generic message and add a specific message when case 1 happens,
so that we always have one specific message without even increasing the
number of dev_dbg*() calls.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add "skip" in "so we can *skip* the current channel" or it doesn't make
sense.
Also add articles where appropriate to fix English grammar.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Clarify what this function does.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some fields are irrelevant for Tegra20/VIP. Add a note to clarify that.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Tegra20 VI peripheral can receive parallel input from the VIP parallel
input module. Add it to the allowed properties and augment the existing
nvidia,tegra20-vi example to show a 'vip' property.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VIP is the parallel video capture component within the video input
subsystem of Tegra20 (and other Tegra chips, apparently).
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
this patch advertise the availability of Dual and Quad SPI mode
for ipm design.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Tim.Kuo <Tim.kuo@mediatek.com>
Link: https://lore.kernel.org/r/20230523112608.10298-1-qii.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 4.8Mhz 9.6Mhz and 19.2MHz SCLK values
for MCLK 12MHz and 12.288MHz requested by Intel.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230524125236.57149-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The cper.c file needs to include an extra header, and efi_zboot_entry
needs an extern declaration to avoid these 'make W=1' warnings:
drivers/firmware/efi/libstub/zboot.c:65:1: error: no previous prototype for 'efi_zboot_entry' [-Werror=missing-prototypes]
drivers/firmware/efi/efi.c:176:16: error: no previous prototype for 'efi_attr_is_visible' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:626:6: error: no previous prototype for 'cper_estatus_print' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:649:5: error: no previous prototype for 'cper_estatus_check_header' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:662:5: error: no previous prototype for 'cper_estatus_check' [-Werror=missing-prototypes]
To make this easier, move the cper specific declarations to
include/linux/cper.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The Make variable containing the objcopy flags may be constructed from
the output of build tools operating on build artifacts, and these may
not exist when doing a make clean.
So avoid evaluating them eagerly, to prevent spurious build warnings.
Suggested-by: Pedro Falcato <pedro.falcato@gmail.com>
Tested-by: Alan Bartlett <ajb@elrepo.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Add two helper functions for calling PCS methods. phylink_pcs_config()
allows us to handle PCS configuration specifics in one location, rather
than the two call sites. phylink_pcs_link_up() gives us consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q1TzK-007Exd-Rs@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Epping says:
====================
net: phy: mscc: support VSC8501
this updated series of patches adds support for the VSC8501 Ethernet
PHY and fixes support for the VSC8502 PHY in cases where no other
software (like U-Boot) has initialized the PHY after power up.
The first patch simply adds the VSC8502 to the MODULE_DEVICE_TABLE,
where I guess it was unintentionally missing. I have no hardware to
test my change.
The second patch adds the VSC8501 PHY with exactly the same driver
implementation as the existing VSC8502.
The (new) third patch removes phydev locking from
vsc85xx_rgmii_set_skews(), as discussed for v2 of the patch set.
The (now) fourth patch fixes the initialization for VSC8501 and VSC8502.
I have tested this patch with VSC8501 on hardware in RGMII mode only.
https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/VSC8501-03_Datasheet_60001741A.PDFhttps://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/VSC8502-03_Datasheet_60001742B.pdf
Table 4-42 "RGMII CONTROL, ADDRESS 20E2 (0X14)" Bit 11 for each of
them.
By default the RX_CLK is disabled for these PHYs. In cases where no
other software, like U-Boot, enabled the clock, this results in no
received packets being handed to the MAC.
The patch enables this clock output.
According to Microchip support (case number 01268776) this applies
to all modes (RGMII, GMII, and MII).
Other PHYs sharing the same register map and code, like
VSC8530/31/40/41 have the clock enabled and the relevant bit 11 is
reserved and read-only for them. As per previous discussion the
patch still clears the bit on these PHYs, too, possibly more easily
supporting other future PHYs implementing this functionality.
For the VSC8572 family of PHYs, having a different register map,
no such changes are applied.
====================
Link: https://lore.kernel.org/r/20230523153108.18548-1-david.epping@missinglinkelectronics.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Holding the struct phy_device (phydev) lock is unnecessary when
accessing phydev->interface in the PHY driver .config_init method,
which is the only place that vsc85xx_rgmii_set_skews() is called from.
The phy_modify_paged() function implements required MDIO bus level
locking, which can not be achieved by a phydev lock.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC8501 PHY can use the same driver implementation as the VSC8502.
Adding the PHY ID and copying the handler functions of VSC8502 is
sufficient to operate it.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chuck Lever says:
====================
Bug fixes for net/handshake
Paolo observed that there is a possible leak of sock->file. I
haven't looked into that yet, but it seems to be separate from
the fixes in this series, so no need to hold these up.
====================
The submissions mentions net-next but it means netdev (perhaps
merge window left over when trees are converged). In any case,
it should have gone into net, but was instead applied to net-next
as commit deb2e484ba ("Merge branch 'net-handshake-fixes'").
These are fixes tho, and Chuck needs them to make progress with
the client so double-merging them into net... it is what it is :(
Link: https://lore.kernel.org/r/168381978252.84244.1933636428135211300.stgit@91.116.238.104.host.secureserver.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
