Add doc for the pinctrl controllers on the UltraRISC DP1000 RISC-V SoC.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add 24 pin groups, and their matching drive groups, on ports EE, FF,
GG and HH to the Tegra238 AON pinmux binding. These groups are present
on the AON pin controller, so device trees that mux these pins through
it validate against the schema.
Fixes: 9323f8a0e1 ("dt-bindings: pinctrl: Document Tegra238 pin controllers")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The Allwinner A523 SoC implements 10 GPIO banks in the first pinctrl
instance, but it skips the first bank (PortA), so their index goes from
1 to 10. The same is actually true for the IRQ banks: there are registers
for 11 banks, though the first bank is not implemented (RAZ/WI).
In contrast to previous SoCs, the count of the IRQ banks starts with this
first unimplemented bank, so we need to provide an interrupt for it.
And indeed the A523 user manual lists an interrupt number for PortA, so we
need to increase the maximum number of interrupts per pin controller to 11,
to be able to assign the correct interrupt number for each bank.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The property 'input-voltage-microvolt' is a typo. Rename it to
'input-threshold-voltage-microvolt' to align with the standard pin
configuration defined in pincfg-node.yaml and parsed by pinconf-generic.c.
Fixes: f6ea7004e9 ("dt-bindings: pinctrl: realtek: Add RTD1625 pinctrl binding")
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The driver for MT6795 pinctrl already supports the slew-rate property.
Add its description to the documentation.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Update dt-binding document for pinctrl of Amlogic A9.
In Amlogic A9 SoC, a bank mux register reuse other banks.
The multiplexed part requires special processing and is
therefore incompatible with the previous SoCs.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Tegra264 contains three pin controllers. Document their compatible strings
and describe the list of pins and functions that they provide.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Tegra238 contains two pin controllers. Document their compatible strings
and describe the list of pins and functions that they provide.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
SoC1 in the AST2700 integrates its own pin controller responsible for
pin multiplexing and pin configuration.
The controller manages various peripheral functions such as eSPI, LPC,
VPI, SD, UART, I2C, I3C, PWM and others through SCU registers.
The binding reuses the standard pinmux and generic pin configuration
schemas and does not introduce custom Devicetree properties.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
QUP1_SE4 uses GPIO36 and GPIO37 for two selectable lane pairs. The
previous split added one function name per lane. Since these are usually
configured in pairs in devicetree, it makes more sense to have them
grouped.
So replace the per-lane qup1_se4_l[0-3] names with names for the two
selectable pairs, qup1_se4_01 and qup1_se4_23.
Fixes: 1bd5c56253 ("dt-bindings: pinctrl: qcom,eliza-tlmm: Split QUP1_SE4 lanes")
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Update the binding documentation to include the compatible string for
PM8010 PMIC which has 2 GPIO modules.
Signed-off-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
- Save/restore more registers during suspend/resume on the RZ/G2L and
RZ/V2H SoC families,
- Add support for the RZ/G3L (R9A08G046) SoC,
- Add support for pinconf-groups in debugfs on EMMA Mobile,
SH/R-Mobile, R-Car, RZ/G1, and RZ/G2 SoCs,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCagw1GQAKCRCKwlD9ZEnx
cPOTAP9kh/jlCmzpkS4/htuQZdR8/v842rI2/yZ0Lu3SulIG/wEAwAHS58q2j7sq
Dtl4w8qttYqaxVdeet6QdLDECGsGJA0=
=86Ux
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v7.2-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v7.2
- Save/restore more registers during suspend/resume on the RZ/G2L and
RZ/V2H SoC families,
- Add support for the RZ/G3L (R9A08G046) SoC,
- Add support for pinconf-groups in debugfs on EMMA Mobile,
SH/R-Mobile, R-Car, RZ/G1, and RZ/G2 SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add a compatible for the pinctrl device of the MT6392 PMIC, a variant of
the already supported MT6397.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add a device tree binding for the pin controller found in the
ASPEED AST2700 SoC0.
The controller manages various peripheral functions such as eMMC, USB,
VGA DDC, JTAG, and PCIe root complex signals.
Describe the AST2700 SoC0 pin controller using standard pin multiplexing
and configuration properties.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add documentation for the pin controller found on the Renesas RZ/G3L
(R9A08G046) SoC. The RZ/G3L PFC is similar to the RZ/G3S SoC but has
more pins.
Also add header file similar to RZ/G3E and RZ/V2H as it has alpha
numeric ports.
Document renesas,clonech property for controlling clone channel
control register located on SYSC IP block on RZ/G3L SoC.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Qualcomm TLMM-based pin controllers share the same gpio-hog binding
semantics across multiple SoCs. The gpio-hog pattern currently defined in
qcom,ipq4019-pinctrl.yaml and qcom,sdm845-pinctrl.yaml are not SOC specific
and applies to all TLMM controllers.
Move the gpio-hog patternProperties definition to qcom,tlmm-common.yaml so
that it can be reused by other Qualcomm TLMM pinctrl bindings and avoid
schema duplication.
Signed-off-by: Swati Agarwal <swati.agarwal@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add a generic pinctrl binding for board-level pinmux chips that are
controlled through the multiplexer subsystem.
On some boards, especially development boards, external mux chips are used
to switch SoC signals between different peripherals (e.g. MMC and UART).
The mux select lines are often driven by a GPIO expander over I2C,
as illustrated below:
┌──────┐ ┌─────┐
│ SOC │ │ │ ┌───────┐
│ │ │ │───►│ MMC │
│ │ │ MUX │ └───────┘
│ ├─────►│ │ ┌───────┐
│ │ │ │───►│ UART │
│ │ └─────┘ └───────┘
│ │ ▲
│ │ ┌────┴──────────────┐
│ I2C ├───►│ GPIO Expander │
└──────┘ └───────────────────┘
Traditionally, gpio-hog is used to configure the onboard mux at boot.
However, the GPIO expander may probe later than consumer devices such as
MMC. As a result, the MUX might not be configured when the peripheral
driver probes, leading to initialization failures or data transfer errors.
Introduce a generic pinctrl binding that models the board-level MUX as a
pin control provider and builds proper device links between the MUX, its
GPIO controller, and peripheral devices. This ensures correct probe
ordering and reliable mux configuration.
The implementation leverages the standard multiplexer subsystem, which
provides broad support for onboard mux controllers and avoids the need for
per-driver custom MUX handling.
Allow pinctrl-* pattern as node name because this pinctrl device have not
reg property.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add a DT binding document describing the TLMM pin controller available
on the Nord platforms from Qualcomm.
Co-developed-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
QUP1_SE4 shares GPIO_36 & GPIO_37 for both L0/L1 and L3/L2 so the
function name cannot be the same or the alternate function cannot
be selected.
Split them up into individual lane functions so boards can specify.
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Several QUP lanes have MIRA/MIRB mirror routings that let the same lane
be muxed out on alternative GPIOs. On Eliza these were all collapsed
under the base function name (e.g. qup1_se6), which prevented boards
from selecting the mirror variants.
Add explicit function names for each mirror lane, matching the pattern
already established by qcom,sm8550-tlmm and related bindings.
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The binding does not reference any other schema, thus should use
"additionalProperties: false" to disallow any undocumented properties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Binding should require 'reg' property, because address space cannot be
missing in the hardware and is already needed by the Linux drivers.
Require also 'compatible' by convention, although it is not strictly
necessary.
Fixes: 857982138b ("dt-bindings: pinctrl: Document Tegra234 pin controllers")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Core changes:
- Perform basic checks on pin config properties so as not to
allow directly contradictory settings such as setting a pin
to more than one bias or drive mode.
- Handle input-threshold-voltage-microvolt property.
- Introduce pinctrl_gpio_get_config() handling in the core for
SCMI GPIO using pin control.
New drivers:
- GPIO-by-pin control driver (also apperaing in the GPIO pull
request) fulfilling a promise on a comment from
Grant Likely many years ago: "can't GPIO just be a front-end
for pin control?" it turns out it can, if and only if you
design something new from scratch, such as SCMI.
- Broadcom BCM7038 as a pinctrl-single delegate.
- Mobileye EyeQ6Lplus OLB pin controller.
- Qualcomm Eliza and Hawi families TLMM pin controllers.
- Qualcomm SDM670 and Milos family LPASS LPI pin controllers.
- Qualcomm IPQ5210 pin controller.
- Realtek RTD1625 pin controller support.
- Rockchip RV1103B pin controller support.
- Texas Instruments AM62L as a pinctrl-single delegate.
Improvements:
- Set config implementation for the Spacemit K1 pin controller.
-----BEGIN PGP SIGNATURE-----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=mkXM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Perform basic checks on pin config properties so as not to allow
directly contradictory settings such as setting a pin to more than
one bias or drive mode
- Handle input-threshold-voltage-microvolt property
- Introduce pinctrl_gpio_get_config() handling in the core for SCMI
GPIO using pin control
New drivers:
- GPIO-by-pin control driver (also appearing in the GPIO pull
request) fulfilling a promise on a comment from Grant Likely many
years ago: "can't GPIO just be a front-end for pin control?" it
turns out it can, if and only if you design something new from
scratch, such as SCMI
- Broadcom BCM7038 as a pinctrl-single delegate
- Mobileye EyeQ6Lplus OLB pin controller
- Qualcomm Eliza and Hawi families TLMM pin controllers
- Qualcomm SDM670 and Milos family LPASS LPI pin controllers
- Qualcomm IPQ5210 pin controller
- Realtek RTD1625 pin controller support
- Rockchip RV1103B pin controller support
- Texas Instruments AM62L as a pinctrl-single delegate
Improvements:
- Set config implementation for the Spacemit K1 pin controller"
* tag 'pinctrl-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (84 commits)
pinctrl: qcom: Add Hawi pinctrl driver
dt-bindings: pinctrl: qcom: Describe Hawi TLMM block
dt-bindings: pinctrl: pinctrl-max77620: convert to DT schema
pinctrl: single: Add bcm7038-padconf compatible matching
dt-bindings: pinctrl: pinctrl-single: Add brcm,bcm7038-padconf
dt-bindings: pinctrl: apple,pinctrl: Add t8122 compatible
pinctrl: qcom: sdm670-lpass-lpi: label variables as static
pinctrl: sophgo: pinctrl-sg2044: Fix wrong module description
pinctrl: sophgo: pinctrl-sg2042: Fix wrong module description
pinctrl: qcom: add sdm670 lpi tlmm
dt-bindings: pinctrl: qcom: Add SDM670 LPASS LPI pinctrl
dt-bindings: qcom: lpass-lpi-common: add reserved GPIOs property
pinctrl: qcom: Introduce IPQ5210 TLMM driver
dt-bindings: pinctrl: qcom: add IPQ5210 pinctrl
pinctrl: qcom: Drop redundant intr_target_reg on modern SoCs
pinctrl: qcom: eliza: Fix interrupt target bit
pinctrl: core: Don't use "proxy" headers
pinctrl: amd: Support new ACPI ID AMDI0033
pinctrl: renesas: rzg2l: Drop superfluous blank line
pinctrl: renesas: rzg2l: Fix save/restore of {IOLH,IEN,PUPD,SMT} registers
...
The Top Level Mode Multiplexer (TLMM) in the Qualcomm Hawi SoC
provides GPIO and pinctrl functionality for UFS, SDC and 226
GPIO pins.
Add a DeviceTree binding to describe the TLMM block on Qualcomm's
Hawi SoC.
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Convert pinctrl-max77620 devicetree bindings for the MAX77620 PMIC from
TXT to YAML format. This patch does not change any functionality; the
bindings remain the same.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add the "brcm,bcm7038-padconf" compatible to the pinctrl-single binding.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The pin controller on the Apple silicon t8122 (M3) SoC is compatible
with the existing driver. Add "apple,t8122-pinctrl" as SoC specific
compatible under "apple,t8103-pinctrl" used by the driver.
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add the pin controller for the audio Low-Power Island (LPI) on SDM670.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
There can be reserved GPIOs on the LPASS LPI pin controller to possibly
control sensors. Add the property for reserved GPIOs so they can be
avoided appropriately.
Adapted from the same entry in qcom,tlmm-common.yaml.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
- Add pin configuration support for RZ/T2H and RZ/N2H,
- Fix save/restore of registers for ports with variable pincfg per pin
on RZ/G3E, RZ/V2H(P), RZ/V2N, and RZ/Five,
- Drop a superfluous blank line.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCacZV5AAKCRCKwlD9ZEnx
cIV9AQDLvTixEFxKC+rtfYF9pLjvYVx+4GS4Fw8vGa96XrpWFQEA4gudqo3LcOZF
lvM+i6XxQN5x7Uot4vVjgyVePY7kuAk=
=neS4
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v7.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v7.1
- Add pin configuration support for RZ/T2H and RZ/N2H,
- Fix save/restore of registers for ports with variable pincfg per pin
on RZ/G3E, RZ/V2H(P), RZ/V2N, and RZ/Five,
- Drop a superfluous blank line.
Signed-off-by: Linus Walleij <linusw@kernel.org>
HDP being functional depends on the debug configuration on the platform
that can be checked using the access-controllers property, document it.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Linus Walleij <linusw@kernel.org>
Link: https://lore.kernel.org/r/20260226-debug_bus-v6-2-5d794697798d@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The previous description was misleading because this hardware block is not
a PWM generator. It does not generate a signal with a specific frequency
and duty ratio.
Instead, it provides a fixed nanosecond-level adjustment to the rising/
falling edges of an existing signal.
The property name is kept as 'realtek,duty-cycle' rather than being
renamed to strictly preserve Device Tree ABI backward compatibility.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add a generic pin configuration property
"input-threshold-voltage-microvolt" to support hardware designs where the
input logic threshold is decoupled from the power supply voltage.
This property allows the pinctrl driver to configure the correct internal
reference voltage for pins that need to accept input signals at a different
voltage level than their power supply. For example, a pin powered by 3.3V
may need to accept 1.8V logic signals.
This defines the reference for VIH (Input High Voltage) and VIL (Input Low
Voltage) thresholds, enabling proper signal detection across different
voltage domains.
Signed-off-by: Tzuyi Chang <tychang@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
It is possible that devices tristate buffers may set the buffer to
the high-Z state in addition to setting pull-up or pull-down on a pin.
Remove this particular restriction to prevent warning on zynqmp systems
where this configuration seems to be valid.
Reported-by: Rob Herring (Arm) <robh@kernel.org>
Fixes: a901e8705f ("dt-bindings: pinctrl: pincfg-node: add restrictions on conflicting properties")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Even though the type of the 'groups' property of a pinmux node is
specified as string-array in pinmux-node.yaml, but trying to use
multiple strings causes dtbs_check warnings.
For example, checking the following dts ...
$ cat arch/arm64/boot/dts/marvell/armada-3720-test.dts
/dts-v1/;
#include "armada-372x.dtsi"
&pinctrl_nb {
pwm-gpio-pins {
groups = "pwm0", "pwm1", "pwm2", "pwm3";
function = "gpio";
};
};
... results in this warning:
arch/arm64/boot/dts/marvell/armada-3720-test.dtb: pinctrl@13800 (marvell,armada3710-nb-pinctrl): pwm-gpio-pins:groups: ['pwm0', 'pwm1', 'pwm2', 'pwm3'] is too long
from schema $id: http://devicetree.org/schemas/pinctrl/marvell,armada3710-xb-pinctrl.yaml
Add the missing 'items' keyword to the schema to allow using multiple
strings without such warnings. Also adjust the indentation of the next
statements accordingly.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: c1c9641a04 ("dt-bindings: pinctrl: Convert marvell,armada-3710-(sb|nb)-pinctrl to DT schema")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Many of the possible pincfg properties are not compatible with one
another, either because they represent mutually exclusive states for a
pin or because they provide the same information in different units.
Add some simple restrictions to prevent invalid configurations.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Document the Top Level Mode Multiplexer on the Eliza Platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>