Sharing a single workqueue between coredump processing and RX
delays evacuation of RX events while a coredump is in progress.
The firmware's RX buffers can overflow during that window, leading
to dropped events. The issue was observed in HID use cases where
HID reports arrive in bursts and quickly fill the RX path while a
coredump is being collected.
Move coredump processing to a dedicated ordered coredump_workqueue
with its own coredump_work, so coredumps run independently of RX.
All four coredump trigger sources (FW assert, HW exception, user
sysfs trigger, and resume-error detection) are switched to this new
workqueue. Ordering serialises concurrent triggers without blocking
RX.
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Load the IOSF DBGC base address based on the controller hardware
variant when reading DRAM buffers during a trace dump. Scorpius
Peak family controllers (SCP/SCP2/SCP2F) use a different DBGC base
address (0xf0d5d500) than Blazar family controllers (BZRI/BZRIW,
0xf3800300).
Fixes: 07e6bddb54 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Based on the debug configuration, firmware can raise MSI-X interrupt with
firmware trigger cause bit set on specific events like Disconnection,
Connection Timeout, Page Timeout etc.
Upon receiving an MSI-X interrupt with the firmware trigger cause bit
set, the driver performs the following actions:
1. Reads Device Memory: Retrieves data from the device memory,
constructs an HCI diagnostic event, and sends it to the monitor. This
event includes details about the trigger, such as connection timeout or
page timeout.
2. Dumps Device Coredump: Generates a coredump containing firmware
traces for further analysis.
The coredump can be retrieved using:
$ cat /sys/class/devcoredump/devcd*/data > /tmp/btintel_coredump.bin
HCI traces:
= Vendor Diagnostic (len 12)
a5 a5 a5 a5 01 03 00 23 00 01 00 00
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When driver encounters a TOP exception, ACPI methods will be called
for Product level reset since Wifi and BT share the same TOP. BT driver
will first reprobe the wifi driver and then reprobe BT.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btintel_pcie_get_mac_access() and btintel_pcie_release_mac_access()
were programming STOP_MAC_ACCESS_DIS and XTAL_CLK_REQ in addition to
the MAC_ACCESS_REQ handshake. These bits are not part of the host
MAC-access handshake on the supported parts; the driver was
programming them incorrectly. Drop the writes so the register update
contains only the bits the controller actually consumes.
Fixes: b9465e6670 ("Bluetooth: btintel_pcie: Read hardware exception data")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CSR boot stage register bit 12 is documented as a device warning,
not a fatal error. Rename the bit definition accordingly and stop
including it in btintel_pcie_in_error().
This keeps warning-only boot stage values from being classified as
errors while preserving abort-handler state as the actual error
condition.
Fixes: 190377500f ("Bluetooth: btintel_pcie: Dump debug registers on error")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Align each descriptor/index/context region to 128 bytes before
calculating the total DMA pool size. This ensures the memory layout
shared with firmware meets the 128-byte alignment requirement.
The DMA pool alignment is also set to 128 bytes to match the firmware
expectation for all shared structures.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to a hardware bug during suspend/resume, the controller may miss a
doorbell interrupt. To address this, a retry mechanism has been added to
inform the controller before reporting a failure.
Test case:
- run suspend and resume cycles.
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During S4 (hibernate), the Bluetooth device loses power. Upon resume,
the driver performs the following actions:
1. Unregisters hdev
2. Calls function level reset
3. Registers hdev
Test case:
- run command sudo rtcwake -m disk -s 60
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As device coredumps are not HCI traces, maintain the device coredump at
the driver level and eliminate the dependency on hdev_devcd*()
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: 07e6bddb54 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver supports Function Level Reset (FLR) to recover the controller
upon hardware exceptions or hci command timeouts. FLR is triggered only
when no prior reset has occurred within the retry window, with a maximum
of one FLR allowed within this window.
This patch is tested by,
echo 1 > /sys/class/bluetooth/hciX/reset
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This change addresses latency issues observed in HID use cases where
events arrive in bursts. By increasing the Rx descriptor count to 64,
the firmware can handle bursty data more effectively, reducing latency
and preventing buffer overflows.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver was posting only 6 rx buffers, despite the maximum rx buffers
being defined as 16. Having fewer RX buffers caused firmware exceptions
in HID use cases when events arrived in bursts.
Exception seen on android 6.12 kernel.
E Bluetooth: hci0: Received hw exception interrupt
E Bluetooth: hci0: Received gp1 mailbox interrupt
D Bluetooth: hci0: 00000000: ff 3e 87 80 03 01 01 01 03 01 0c 0d 02 1c 10 0e
D Bluetooth: hci0: 00000010: 01 00 05 14 66 b0 28 b0 c0 b0 28 b0 ac af 28 b0
D Bluetooth: hci0: 00000020: 14 f1 28 b0 00 00 00 00 fa 04 00 00 00 00 40 10
D Bluetooth: hci0: 00000030: 08 00 00 00 7a 7a 7a 7a 47 00 fb a0 10 00 00 00
D Bluetooth: hci0: 00000000: 10 01 0a
E Bluetooth: hci0: ---- Dump of debug registers —
E Bluetooth: hci0: boot stage: 0xe0fb0047
E Bluetooth: hci0: ipc status: 0x00000004
E Bluetooth: hci0: ipc control: 0x00000000
E Bluetooth: hci0: ipc sleep control: 0x00000000
E Bluetooth: hci0: mbox_1: 0x00badbad
E Bluetooth: hci0: mbox_2: 0x0000101c
E Bluetooth: hci0: mbox_3: 0x00000008
E Bluetooth: hci0: mbox_4: 0x7a7a7a7a
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On hardware error, controller writes hardware error event and optional
vendor specific hci events in device memory in TLV format and raises
MSIX interrupt. Driver reads the device memory and passes the events to
the stack for further processing.
Co-developed-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch allocates the host memory which is used by controller to dump
the firmware traces. The memory needs to be shared with controller via
context information.
Co-developed-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a recovery mechanism to recover controller if firmware
download fails due to unresponsive controller, command timeout, firmware
signature verification failure etc. Driver attmepts maximum of 5 times
before giving up.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The following handshake mechanism needs be followed after firmware
download is completed to bring the firmware to running state.
After firmware fragments of Operational image are downloaded and
secure sends result of the image succeeds,
1. Driver sends HCI Intel reset with boot option #1 to switch FW image.
2. FW sends Alive GP[0] MSIx
3. Driver enables data path (doorbell 0x460 for RBDs, etc...)
4. Driver gets Bootup event from firmware
5. Driver performs D0 entry to device (WRITE to IPC_Sleep_Control =0x0)
6. FW sends Alive GP[0] MSIx
7. Device host interface is fully set for BT protocol stack operation.
8. Driver may optionally get debug event with ID 0x97 which can be dropped
For Intermediate loadger image, all the above steps are applicable
expcept #5 and #6.
On HCI_OP_RESET, firmware raises alive interrupt. Driver needs to wait
for it before passing control over to bluetooth stack.
Co-developed-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Minor refactor and s/TX_WAIT_TIMEOUT_MS/BTINTEL_PCIE_TX_WAIT_TIMEOUT_MS/g.
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add initial code to support Intel bluetooth devices based on PCIe
transport. Allocate memory for TX & RX buffers, internal structures,
initialize interrupts for TX & RX and PCIe device.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
