gpiochip_set_multiple() falls back to setting lines one by one when the
chip does not provide set_multiple(). If the fallback path receives an
empty mask, the loop is skipped and ret is returned without being
initialized.
Initialize ret to 0 so an empty mask is treated as a successful no-op.
Fixes: 9b40731275 ("gpiolib: rework the wrapper around gpio_chip::set_multiple()")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260620155319.79994-1-ruoyuw560@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
GPIO core:
- Add an initial set of kunit test cases for the GPIO subsystem
- Use the devres owner as the GPIO chip's parent in absence of any other
parent
- Fix const-correctness of GPIO chip SRCU guards
- Provide new GPIO consumer interfaces: gpiod_is_single_ended() and
fwnode_gpiod_get()
- Quarantine all legacy GPIO APIs in linux/gpio/legacy.h
- Use __ro_after_init where applicable
New drivers:
- Add driver for the GPIO controller on Waveshare DSI TOUCH panels
Removed drivers:
- Remove the obsolete ts5500 GPIO driver
Driver updates:
- Modernize gpio-timberdale: remove platform data support and use generic
device property accessors
- Extend test build coverage by enabling COMPILE_TEST for more GPIO
drivers
- Add some missing dependencies in Kconfig
- Add support for sparse fixed direction to gpio-regmap
- Remove dead code from gpio-nomadik
- use BIT() in gpio-mxc
- use bitmap_complement() in gpio-xilinx and gpio-pca953x
- Use more appropriate printing functions where applicable
- Use named initializers for platform_device_id and i2c_device_id arrays
- Convert gpio-altera to using the generic GPIO chip helper library
- Add support for new models to gpio-dwapb, gpio-zynq, gpio-usbio and
gpio-tegra186
- Unify the naming convention for Qualcomm in GPIO drivers
- Fix interrupt bank mapping to GPIO chips in gpio-mt7621
- Add support for the lines-initial-states property to gpio-74x164
- Switch to using dynamic GPIO base in gpio-ixp4xx
- Move the handling of an OF quirk from ASoC to gpiolib-of.c where other
such quirks live
- Use handle_bad_irq() in gpio-ep93xx
- Some other minor tweaks and refactorings
Devicetree bindings:
- Document the Waveshare GPIO controller for DSI TOUCH panels
- Document new models: Tegra238 in gpio-tegra186 and EIO GPIO in gpio-zynq
- Add new properties for gpio-dwapb and fairchild,74hc595
- Fix whitespace issues
- Sort compatibles alphabetically in gpio-zynq
Documentation:
- Fix kerneldoc warnings in gpio-realtek-otto
Misc:
- Attach software nodes representing GPIO chips to the actual struct
device objects associated with them in some legacy platforms enabling
real firmware node lookup instead of string matching
- Drop unneeded dependencies on OF_GPIO from bus and staging drivers
-----BEGIN PGP SIGNATURE-----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=MzJz
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver, one legacy driver removed, a kunit test-suite
for the GPIO core, support for new models in existing drivers and a
slew of various changes in many places though I can't think of
anything controversial that would stand out - it's been a relatively
calm cycle.
GPIO core:
- Add an initial set of kunit test cases for the GPIO subsystem
- Use the devres owner as the GPIO chip's parent in absence of any
other parent
- Fix const-correctness of GPIO chip SRCU guards
- Provide new GPIO consumer interfaces: gpiod_is_single_ended() and
fwnode_gpiod_get()
- Quarantine all legacy GPIO APIs in linux/gpio/legacy.h
- Use __ro_after_init where applicable
New drivers:
- Add driver for the GPIO controller on Waveshare DSI TOUCH panels
Removed drivers:
- Remove the obsolete ts5500 GPIO driver
Driver updates:
- Modernize gpio-timberdale: remove platform data support and use
generic device property accessors
- Extend test build coverage by enabling COMPILE_TEST for more GPIO
drivers
- Add some missing dependencies in Kconfig
- Add support for sparse fixed direction to gpio-regmap
- Remove dead code from gpio-nomadik
- use BIT() in gpio-mxc
- use bitmap_complement() in gpio-xilinx and gpio-pca953x
- Use more appropriate printing functions where applicable
- Use named initializers for platform_device_id and i2c_device_id
arrays
- Convert gpio-altera to using the generic GPIO chip helper library
- Add support for new models to gpio-dwapb, gpio-zynq, gpio-usbio and
gpio-tegra186
- Unify the naming convention for Qualcomm in GPIO drivers
- Fix interrupt bank mapping to GPIO chips in gpio-mt7621
- Add support for the lines-initial-states property to gpio-74x164
- Switch to using dynamic GPIO base in gpio-ixp4xx
- Move the handling of an OF quirk from ASoC to gpiolib-of.c where
other such quirks live
- Use handle_bad_irq() in gpio-ep93xx
- Some other minor tweaks and refactorings
Devicetree bindings:
- Document the Waveshare GPIO controller for DSI TOUCH panels
- Document new models: Tegra238 in gpio-tegra186 and EIO GPIO in
gpio-zynq
- Add new properties for gpio-dwapb and fairchild,74hc595
- Fix whitespace issues
- Sort compatibles alphabetically in gpio-zynq
Documentation:
- Fix kerneldoc warnings in gpio-realtek-otto
Misc:
- Attach software nodes representing GPIO chips to the actual struct
device objects associated with them in some legacy platforms
enabling real firmware node lookup instead of string matching
- Drop unneeded dependencies on OF_GPIO from bus and staging drivers"
* tag 'gpio-updates-for-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (62 commits)
gpio: nomadik: remove dead DB8540 code from <gpio/gpio-nomadik.h>
gpio: mt7621: fix interrupt banks mapping on gpio chips
bus: ts-nbus: drop unneeded dependency on OF_GPIO
staging: media: max96712: drop unneeded dependency on OF_GPIO
gpiolib: Replace strcpy() with memcpy()
gpio: remove obsolete UAF FIXMEs from lookup paths
gpio: core: fix const-correctness of gpio_chip_guard
gpio: mxc: use BIT() macro
gpio: realtek-otto: fix kernel-doc warnings
gpio: max77620: Unify usage of space and comma in platform_device_id array
gpio: Use named initializers for platform_device_id arrays
gpio: cros-ec: Drop unused assignment of platform_device_id driver data
ARM: omap1: enable real software node lookup of GPIOs on Nokia 770
ARM: omap1: use platform_device_register_full() for GPIO devices on OMAP 16xx
ARM: omap1: drop unused variable from omap16xx_gpio_init()
gpio: gpiolib: use seq_puts() for plain strings
gpio: ts5500: remove obsolete driver
gpio: add kunit test cases for the GPIO subsystem
kunit: provide kunit_platform_device_unregister()
kunit: provide kunit_platform_device_register_full()
...
Commit d1d564ec49 ("gpio: move hogs into GPIO core") introduced a
behaviour change that breaks boot on Raspberry Pi 5 when using the
firmware-supplied device tree:
gpiochip_add_data_with_key: GPIOs 544..575
(/soc@107c000000/gpio@7d517c00) failed to register, -22
brcmstb-gpio 107d517c00.gpio: Could not add gpiochip for bank 1
brcmstb-gpio 107d517c00.gpio: probe with driver brcmstb-gpio failed
with error -22
gpio-brcmstb registers two gpio_chips against the device tree
node gpio@7d517c00, one for each bank. The firmware-supplied DT includes
a gpio-hog on RP1 RUN, and this gpio-hog is attempted to be applied to
*both* gpio_chips. This succeeds against bank 0 (which hosts the GPIO)
and fails for bank 1 (which does not).
In the previous implementation, failures to apply gpio-hogs were
quietly ignored. In the new code, the error code propagates and causes
probe to fail.
Closely approximate the previous behaviour by using the OF_POPULATED flag
to ensure that each gpio-hog is processed only once. The flag was
previously being set before the gpio-hogs were processed, so as part
of this change, the flag now gets set only after the gpio-hog is actioned.
The handling of gpio-hogs on a DT node with multiple gpio_chips remains a
bit incomplete/unclear, but this at least retains the ability to apply
hogs to the first gpio_chip per node.
Fixes: d1d564ec49 ("gpio: move hogs into GPIO core")
Signed-off-by: Daniel Drake <dan@reactivated.net>
Link: https://patch.msgid.link/20260608210108.36248-1-dan@reactivated.net
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If gpiochip_hog_lines() successfully processes some hogs but fails on
a later one, the error handling path in gpiochip_add_data_with_key()
jumps directly to err_remove_of_chip. This leaks resources allocated
earlier for ACPI, interrupts and hogs that were successfully processed.
Use the right label in error path.
Closes: https://sashiko.dev/#/patchset/20260608210108.36248-1-dan%40reactivated.net
Fixes: d1d564ec49 ("gpio: move hogs into GPIO core")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20260609-gpio-hogs-fixes-v1-2-b4064f8070e7@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The length of the string is calculated in order to allocate the correct
sized memory block, use the same length to copy the string.
Signed-off-by: David Laight <david.laight.linux@gmail.com>
Link: https://patch.msgid.link/20260606202633.5018-3-david.laight.linux@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The DEFINE_CLASS macro for gpio_chip_guard currently expects a non-const
struct gpio_desc pointer. This prevents the guard from being used cleanly
in fast paths that receive a const descriptor, forcing developers to fall
back to open-coding the SRCU locks.
Update the macro to accept a const struct gpio_desc pointer. This is valid
because the actual targeted gpio_device pointer assignment does not drop
const qualifiers on the target structure.
Convert the open-coded SRCU locks in gpiod_get_raw_value_commit() and
gpiod_to_irq() to use the guard, removing their legacy FIXME comments.
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Marco Scardovi <scardracs@disroot.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260524162708.62949-2-scardracs@disroot.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Replace seq_printf() with seq_puts() where the format string is a
plain string literal with no format specifiers.
No functional change intended.
Signed-off-by: Chen Jung Ku <ku.loong@gapp.nthu.edu.tw>
Link: https://patch.msgid.link/20260526121905.46345-1-ku.loong@gapp.nthu.edu.tw
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The 'gpio_devt' and 'gpiolib_initialized' variables are initialized only
during the init phase in the 'gpiolib_dev_init' function and never
changed. So, mark these as __ro_after_init.
The 'gpio_stub_drv' variable is initialized only in the declaration and
never changed. So, this variable could be 'const', but using the
'driver_register' and 'driver_unregister' functions discards the 'const'
qualifier. Therefore, as an alternative, mark it as a __ro_after_init.
Signed-off-by: Len Bao <len.bao@gmx.us>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260516105737.45174-1-len.bao@gmx.us
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The direction of a single-ended (open-drain or open-source) GPIO line
cannot always be reliably determined by reading hardware registers.
In true open-drain implementations, the "high" state is achieved by
entering a high-impedance mode, which many hardware controllers report
as "input" even if the software intends to use it as an output.
This creates issues for consumer drivers (like I2C) that rely on
gpiod_get_direction() to decide if a line can be driven.
Introduce gpiod_is_single_ended() to allow consumers to check the
software configuration (GPIO_FLAG_OPEN_DRAIN/GPIO_FLAG_OPEN_SOURCE) of
a descriptor. This provides a robust way to identify lines that are
capable of being driven, regardless of their instantaneous hardware state.
Signed-off-by: Jie Li <jie.i.li@nokia.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260511113726.49041-2-jie.i.li@nokia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
GPIO core:
- defer probe on software node lookups when the remote software node
exists but has not been registered as a firmware node yet
- unify GPIO hog handling by moving code duplicated in OF and ACPI
modules into GPIO core and allow setting up hogs with software nodes
- allow matching GPIO controllers by secondary firmware node if matching
by primary does not succeed
- demote deferral warnings to debug level as they are quite normal when
using software nodes which don't support fw_devlink yet
- disable the legacy GPIO character device uAPI v1 supprt in Kconfig by
default
- rework several core functions in preparation for the upcoming Revocable
helper library for protecting resources against sudden removal, this
reduces the number of SRCU dereferences in GPIO core
- simplify file descriptor logic in GPIO character device code by using
FD_PREPARE()
- introduce a header defining symbols used by both GPIO consumers and
providers to avoid having to include provider-specific headers from
drivers which only consume GPIOs
- replace snprintf() with strscpy() where formatting is not required
New drivers:
- add the gpio-by-pinctrl generic driver using the ARM SCMI protocol to
control GPIOs (along with SCMI changes pulled from the pinctrl tree)
- add a driver providing support for handling of platform events via
GPIO-signalled ACPI events (used on Intel Nova Lake and later platforms)
Driver changes:
- extend the gpio-kempld driver with support for more recent models,
interrupts and setting/getting multiple values at once
- improve interrupt handling in gpio-brcmstb
- add support for multi-SoC systems in gpio-tegra186
- make sure we return correct values from the .get() callbacks in several
GPIO drivers by normalizing any values other than 0, 1 or negative error
numbers
- use flexible arrays in several drivers to reduce the number of required
memory allocations
- simplify synchronous waiting for virtual drivers to probe and remove the
dedicated, a bit overengineered helper library dev-sync-probe
- remove unneeded Kconfig dependencies on OF_GPIO in several drivers and
subsystems
- convert the two remaining users of of_get_named_gpio() to using GPIO
descriptors and remove the (no longer used) function along with the
header that declares it
- add missing includes in gpio-mmio
- shrink and simplify code in gpio-max732x by using guard(mutex)
- remove duplicated code handling the 'ngpios' property from gpio-ts4800,
it's already handled in GPIO core
- use correct variable type in gpio-aspeed
- add support for a new model in gpio-realtek-otto
- allow to specify the active-low setting of simulated hogs over the
configfs interface (in addition to existing devicetree support) in
gpio-sim
Bug fixes:
- clear the OF_POPULATED flag on hog nodes in GPIO chip remove path on
OF systems
- fix resource leaks in error path in gpiochip_add_data_with_key()
- drop redundant device reference in gpio-mpsse
Tests:
- add selftests for use-after-free cases in GPIO character device code
DT bindings:
- add a DT binding document for SCMI based, gpio-over-pinctrl devices
- fix interrupt description in microchip,mpfs-gpio
- add new compatible for gpio-realtek-otto
- describe the resets of the mpfs-gpio controller
- fix maintainer's email in gpio-delay bindings
- remove the binding document for cavium,thunder-8890 as the corresponding
device is bound over PCI and not firmware nodes
Documentation:
- update the recommended way of converting legacy boards to using software
nodes for GPIO description
- describe GPIO line value semantics
- misc updates to kerneldocs
Misc:
- convert OMAP1 ams-delta board to using GPIO hogs described with software
nodes
-----BEGIN PGP SIGNATURE-----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=VknJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"For this merge window we have two new drivers: support for
GPIO-signalled ACPI events on Intel platforms and a generic
GPIO-over-pinctrl driver using the ARM SCMI protocol for
controlling pins.
Several things have been reworked in GPIO core: we unduplicated GPIO
hog handling, reduced the number of SRCU locks and dereferences,
improved support for software-node-based lookup and removed more
legacy code after converting remaining users to modern alternatives.
There's also a number of driver reworks and refactoring, documentation
updates, some bug-fixes and new tests.
GPIO core:
- defer probe on software node lookups when the remote software node
exists but has not been registered as a firmware node yet
- unify GPIO hog handling by moving code duplicated in OF and ACPI
modules into GPIO core and allow setting up hogs with software
nodes
- allow matching GPIO controllers by secondary firmware node if
matching by primary does not succeed
- demote deferral warnings to debug level as they are quite normal
when using software nodes which don't support fw_devlink yet
- disable the legacy GPIO character device uAPI v1 supprt in Kconfig
by default
- rework several core functions in preparation for the upcoming
Revocable helper library for protecting resources against sudden
removal, this reduces the number of SRCU dereferences in GPIO core
- simplify file descriptor logic in GPIO character device code by
using FD_PREPARE()
- introduce a header defining symbols used by both GPIO consumers and
providers to avoid having to include provider-specific headers from
drivers which only consume GPIOs
- replace snprintf() with strscpy() where formatting is not required
New drivers:
- add the gpio-by-pinctrl generic driver using the ARM SCMI protocol
to control GPIOs (along with SCMI changes pulled from the pinctrl
tree)
- add a driver providing support for handling of platform events via
GPIO-signalled ACPI events (used on Intel Nova Lake and later
platforms)
Driver changes:
- extend the gpio-kempld driver with support for more recent models,
interrupts and setting/getting multiple values at once
- improve interrupt handling in gpio-brcmstb
- add support for multi-SoC systems in gpio-tegra186
- make sure we return correct values from the .get() callbacks in
several GPIO drivers by normalizing any values other than 0, 1 or
negative error numbers
- use flexible arrays in several drivers to reduce the number of
required memory allocations
- simplify synchronous waiting for virtual drivers to probe and
remove the dedicated, a bit overengineered helper library
dev-sync-probe
- remove unneeded Kconfig dependencies on OF_GPIO in several drivers
and subsystems
- convert the two remaining users of of_get_named_gpio() to using
GPIO descriptors and remove the (no longer used) function along
with the header that declares it
- add missing includes in gpio-mmio
- shrink and simplify code in gpio-max732x by using guard(mutex)
- remove duplicated code handling the 'ngpios' property from
gpio-ts4800, it's already handled in GPIO core
- use correct variable type in gpio-aspeed
- add support for a new model in gpio-realtek-otto
- allow to specify the active-low setting of simulated hogs over the
configfs interface (in addition to existing devicetree support) in
gpio-sim
Bug fixes:
- clear the OF_POPULATED flag on hog nodes in GPIO chip remove path
on OF systems
- fix resource leaks in error path in gpiochip_add_data_with_key()
- drop redundant device reference in gpio-mpsse
Tests:
- add selftests for use-after-free cases in GPIO character device
code
DT bindings:
- add a DT binding document for SCMI based, gpio-over-pinctrl devices
- fix interrupt description in microchip,mpfs-gpio
- add new compatible for gpio-realtek-otto
- describe the resets of the mpfs-gpio controller
- fix maintainer's email in gpio-delay bindings
- remove the binding document for cavium,thunder-8890 as the
corresponding device is bound over PCI and not firmware nodes
Documentation:
- update the recommended way of converting legacy boards to using
software nodes for GPIO description
- describe GPIO line value semantics
- misc updates to kerneldocs
Misc:
- convert OMAP1 ams-delta board to using GPIO hogs described with
software nodes"
* tag 'gpio-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (79 commits)
gpio: swnode: defer probe on references to unregistered software nodes
dt-bindings: gpio: cavium,thunder-8890: Remove DT binding
Documentation: gpio: update the preferred method for using software node lookup
gpio: gpio-by-pinctrl: s/used to do/is used to do/
gpio: aspeed: fix unsigned long int declaration
gpio: rockchip: convert to dynamic GPIO base allocation
gpio: remove dev-sync-probe
gpio: virtuser: stop using dev-sync-probe
gpio: aggregator: stop using dev-sync-probe
gpio: sim: stop using dev-sync-probe
gpio: Add Intel Nova Lake ACPI GPIO events driver
gpiolib: Make deferral warnings debug messages
gpiolib: fix hogs with multiple lines
gpio: fix up CONFIG_OF dependencies
gpio: gpio-by-pinctrl: add pinctrl based generic GPIO driver
gpio: dt-bindings: Add GPIO on top of generic pin control
firmware: arm_scmi: Allow PINCTRL_REQUEST to return EOPNOTSUPP
pinctrl: scmi: ignore PIN_CONFIG_PERSIST_STATE
pinctrl: scmi: Delete PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS support
pinctrl: scmi: Add SCMI_PIN_INPUT_VALUE
...
With the recent addition of the shared GPIO support, warning messages
such as the following are being observed ...
reg-fixed-voltage regulator-vdd-3v3-pcie: cannot find GPIO chip
gpiolib_shared.proxy.6, deferring
These are seen even with GPIO_SHARED_PROXY=y.
Given that the GPIOs are successfully found a bit later during boot and
the code is intentionally returning -EPROBE_DEFER when they are not
found, downgrade these messages to debug prints to avoid unnecessary
warnings being observed.
Note that although the 'cannot find GPIO line' warning has not been
observed in this case, it seems reasonable to make this print a debug
print for consistency too.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260401133441.47641-1-jonathanh@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Shared GPIOs may be assigned to child nodes of device nodes which don't
themselves bind to any struct device. We need to pass the firmware node
that is the actual consumer to gpiolib-shared and compare against it
instead of unconditionally using the fwnode of the consumer device.
Fixes: a060b8c511 ("gpiolib: implement low-level, shared GPIO support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/all/921ba8ce-b18e-4a99-966d-c763d22081e2@nvidia.com/
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260318-gpio-shared-xlate-v2-2-0ce34c707e81@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
OF-based GPIO controller drivers may provide a translation function that
calculates the real chip offset from whatever devicetree sources
provide. We need to take this into account in the shared GPIO management
and call of_xlate() if it's provided and adjust the entry->offset we
initially set when scanning the tree.
To that end: modify the shared GPIO API to take the GPIO chip as
argument on setup (to avoid having to rcu_dereference() it from the GPIO
device) and protect the access to entry->offset with the existing lock.
Fixes: a060b8c511 ("gpiolib: implement low-level, shared GPIO support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/all/921ba8ce-b18e-4a99-966d-c763d22081e2@nvidia.com/
Reviewed-by: Linus Walleij <linusw@kernel.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260318-gpio-shared-xlate-v2-1-0ce34c707e81@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This reverts commit cc11f4ef66.
Commit cc11f4ef66 ("gpio: Access `gpio_bus_type` in
gpiochip_setup_dev()") moved the bus type assignment from
gpiochip_add_data_with_key() to gpiochip_setup_dev().
This change introduced a bug where dev_printk() and friends might access
the bus name after gpiochip_add_data_with_key() but before
gpiochip_setup_dev() has run. In this window, the bus type is not yet
initialized, leading to empty bus names in logs.
Move the bus type assignment back to gpiochip_add_data_with_key() to
ensure the bus name is available before any potential users like
dev_printk().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdU0Xb=Moca5LUex+VxyHQa2-uYJgYf4hzHiSEjDCQQT=Q@mail.gmail.com/
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260313054112.1248074-1-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This function albeit static was lacking a kerneldoc, and the
function returns a dangerous number for internal use so make
that clear in the kerneldoc.
Reported-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260311-gpio-discourage-dynamic-v1-1-c8b68fc84203@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
With no more users, remove legacy machine hog API from the kernel.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260309-gpio-hog-fwnode-v2-5-4e61f3dbf06a@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Refactor line hogging code by moving the parts duplicated in
gpiolib-acpi-core.c and gpiolib-of.c into gpiolib.c, leaving just the
OF-specific bits in the latter.
This makes fwnode the primary API for setting up hogs and allows to use
software nodes in addition to ACPI and OF nodes.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260309-gpio-hog-fwnode-v2-2-4e61f3dbf06a@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If `gpiochip_line_is_valid()` fails, then `-EINVAL` is returned, but
`desc->flags` will have `GPIOD_FLAG_REQUESTED` set, which will result
in subsequent calls misleadingly returning `-EBUSY`.
Fix that by clearing the flag in case of failure.
Fixes: a501624864 ("gpio: Respect valid_mask when requesting GPIOs")
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20260310204359.1202451-1-pobrn@protonmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Ensure struct gpio_chip for gpiochip_setup_dev(). This eliminates a few
checks for struct gpio_chip.
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260223061726.82161-5-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
gpiochip_sysfs_unregister() is only called by gpiochip_remove() where
the struct gpio_chip is ensured.
Remove the redundant check.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260223061726.82161-4-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
gpiolib_dbg_show() is only called by gpiolib_seq_show() which has
ensured the struct gpio_chip. Remove the redundant check in
gpiolib_dbg_show().
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260223061726.82161-3-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
To make the intent clear, access `gpio_bus_type` only when it's ready in
gpiochip_setup_dev().
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260223061726.82161-2-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Since commit aab5c6f200 ("gpio: set device type for GPIO chips"),
`gdev->dev.release` is unset. As a result, the reference count to
`gdev->dev` isn't dropped on the error handling paths.
Drop the reference on errors.
Also reorder the instructions to make the error handling simpler.
Now gpiochip_add_data_with_key() roughly looks like:
>>> Some memory allocation. Go to ERR ZONE 1 on errors.
>>> device_initialize().
gpiodev_release() takes over the responsibility for freeing the
resources of `gdev->dev`. The subsequent error handling paths
shouldn't go through ERR ZONE 1 again which leads to double free.
>>> Some initialization mainly on `gdev`.
>>> The rest of initialization. Go to ERR ZONE 2 on errors.
>>> Chip registration success and exit.
>>> ERR ZONE 2. gpio_device_put() and exit.
>>> ERR ZONE 1.
Cc: stable@vger.kernel.org
Fixes: aab5c6f200 ("gpio: set device type for GPIO chips")
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20260205092840.2574840-1-tzungbi@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
In GPIOLIB, during fwnode lookup, after having resolved the consumer's
reference to a specific fwnode, we only match it against the primary
node of the controllers. Let's extend that to also the secondary node by
reworking gpio_chip_match_by_fwnode()
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://patch.msgid.link/20260226-device-match-secondary-fwnode-v4-1-27bd0cfbd8c6@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Commit 86ef402d80 ("gpiolib: sanitize the return value of
gpio_chip::get()") started checking the return value of the .get()
callback in struct gpio_chip. Now - almost a year later - it turns out
that there are quite a few drivers in tree that can break with this
change. Partially revert it: normalize the return value in GPIO core but
also emit a warning.
Cc: stable@vger.kernel.org
Fixes: 86ef402d80 ("gpiolib: sanitize the return value of gpio_chip::get()")
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Closes: https://lore.kernel.org/all/aZSkqGTqMp_57qC7@google.com/
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://patch.msgid.link/20260219-gpiolib-set-normalize-v2-1-f84630e45796@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
GPIOLIB core:
- shrink the GPIO bus driver stub code
- rework software node support for "undefined" software nodes
- provide and use devm_fwnode_gpiod_get_optional()
- only compile the OF quirk for MT2701 when needed
New drivers:
- add the GPIO driver for ROHM bd72720
- add the gpio-line-mux driver providing 1-to-many mapping for a single
real GPIO
Driver changes:
- refactor gpio-pca9570: use lock guard, add missing headers, use devres
consistently
- add support for a new model (G7 Aspeed sgpiom) to the aspeed-sgpio driver
along with some prerequisite refactoring
- use device_get_match_data() where applicable and save some lines
- add support for more models to gpio-cadence
- add the compatible property to reset-gpio and use it in shared GPIO
management
- drop unnecessary use of irqd_get_trigger_type() in gpio-max77759
- add support for a new variant to gpio-pca953x
- extend build coverage with COMPILE_TEST for more drivers
- constify configfs structures in gpio-sim and gpio-virtuser
- add support for the K3 SoC to gpio-spacemit
- implement the missing .get_direction() callback in gpio-max77620
- add support for Tegra264 to gpio-tegra186
- drop unneeded MODULE_ALIAS() from gpio-menz127
DT bindings:
- document support for the opencores GPIO controller in gpio-mmio
- document new variants for gpio-pca953x
Documentation:
- extensively describe interrupt source detection for gpio-pca953x and
add more models to the list of supported variants
-----BEGIN PGP SIGNATURE-----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=Zhuy
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and some changes to GPIO core but mostly
just GPIO driver updates across a wide array of files, adding support
for new models as well as various refactoring changes. Nothing
controversial and everything has spent a good measure of time in
linux-next.
GPIOLIB core:
- shrink the GPIO bus driver stub code
- rework software node support for "undefined" software nodes
- provide and use devm_fwnode_gpiod_get_optional()
- only compile the OF quirk for MT2701 when needed
New drivers:
- add the GPIO driver for ROHM bd72720
- add the gpio-line-mux driver providing 1-to-many mapping for a
single real GPIO
Driver changes:
- refactor gpio-pca9570: use lock guard, add missing headers, use
devres consistently
- add support for a new model (G7 Aspeed sgpiom) to the aspeed-sgpio
driver along with some prerequisite refactoring
- use device_get_match_data() where applicable and save some lines
- add support for more models to gpio-cadence
- add the compatible property to reset-gpio and use it in shared GPIO
management
- drop unnecessary use of irqd_get_trigger_type() in gpio-max77759
- add support for a new variant to gpio-pca953x
- extend build coverage with COMPILE_TEST for more drivers
- constify configfs structures in gpio-sim and gpio-virtuser
- add support for the K3 SoC to gpio-spacemit
- implement the missing .get_direction() callback in gpio-max77620
- add support for Tegra264 to gpio-tegra186
- drop unneeded MODULE_ALIAS() from gpio-menz127
DT bindings:
- document support for the opencores GPIO controller in gpio-mmio
- document new variants for gpio-pca953x
Documentation:
- extensively describe interrupt source detection for gpio-pca953x
and add more models to the list of supported variants"
* tag 'gpio-updates-for-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (59 commits)
gpio: tegra186: Add support for Tegra264
dt-bindings: gpio: Add Tegra264 support
gpio: spacemit-k1: Use PDR for pin direction, not SDR/CDR
gpio: max77620: Implement .get_direction() callback
gpio: aspeed-sgpio: Support G7 Aspeed sgpiom controller
dt-bindings: gpio: aspeed,sgpio: Support ast2700
gpio: aspeed-sgpio: Convert IRQ functions to use llops callbacks
gpio: aspeed-sgpio: Create llops to handle hardware access
gpio: aspeed-sgpio: Remove unused bank name field
gpio: aspeed-sgpio: Change the macro to support deferred probe
regulator: bd71815: switch to devm_fwnode_gpiod_get_optional
gpiolib: introduce devm_fwnode_gpiod_get_optional() wrapper
gpio: mmio: Add compatible for opencores GPIO
dt-bindings: gpio-mmio: Correct opencores GPIO
gpio: pca9570: use lock guards
gpio: pca9570: Don't use "proxy" headers
gpio: pca9570: Use devm_mutex_init() for mutex initialization
MAINTAINERS: Add ROHM BD72720 PMIC
power: supply: bd71828-power: Support ROHM BD72720
power: supply: bd71828: Support wider register addresses
...
Just toggling the descriptor's "requested" flag is not enough. We need
to properly request it in order to potentially propagate any
configuration to pinctrl via the .request() callback.
We must not take the reference to the device at this point (the device
is not ready but we're also requesting the device's own descriptor) so
make the _commit() variants of request and free functions available to
GPIO core in order to use them instead of their regular counterparts.
This fixes an audio issue reported on one of the Qualcomm platforms.
Fixes: a060b8c511 ("gpiolib: implement low-level, shared GPIO support")
Reviewed-by: Linus Walleij <linusw@kernel.org>
Tested-by: Ravi Hothi <ravi.hothi@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260120154913.61991-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmlkZHIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGaSUH/jsIthYCRnSsVxms
HVEEKeSTEWUFH7wpnsTle2fep4HC/LmvxX2T07M5XuhgS7fUafnwonaEbs/NvgsT
I0/28Px4ovU69NwFNZ17fOIDdcfIGPzWvcTHK354+PWwKNBciNgSq6AQ+iq1zK4T
2eAUS2CybkMqquIDN1w2Y9dLXHovY6flXAzZZQutd1sqGtIlZl/R5W4qxbtuvS1n
d4Jq40erS5YGganxGcHvC6JFMuh+vEARQjZSOq8J4Cy3z6SvkJoGrg2q3qU3tFAf
/cvVlXwrzxR9XDg+5ZH7c4TlnRWWiz5KDeYNFlqd7Gor3SNTUB8G6WWHkm4JrCZd
EzE+MGw=
=LUKA
-----END PGP SIGNATURE-----
Merge tag 'v6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into gpio/for-next
Linux 6.19-rc5
Pull in upstream shared GPIO fixes into the v7.0 branch.
If on any iteration in gpiod_find(), gpio_desc_table_match() returns
NULL (which is normal and expected), we never reinitialize desc back to
ERR_PTR(-ENOENT) and if we don't find a match later on, we will return
NULL causing a NULL-pointer dereference in users not expecting it. Don't
initialize desc, but return ERR_PTR(-ENOENT) explicitly at the end of
the function.
Fixes: 9700b0fccf ("gpiolib: allow multiple lookup tables per consumer")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/00107523-7737-4b92-a785-14ce4e93b8cb@samsung.com/
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20260108102314.18816-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
When matching the firmware node with the potential consumer, we
currently omit the con_id string. This can lead to false positives in
the unlikely case of the consumer having been assigned more than one
shared GPIO. Check the connector ID before proceeding.
Fixes: a060b8c511 ("gpiolib: implement low-level, shared GPIO support")
Link: https://lore.kernel.org/r/20251222-gpio-shared-reset-gpio-proxy-v1-2-8d4bba7d8c14@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The GPIO machine lookup mechanism dates back to old ARM board files
where lookup tables would all be defined in a single place. Since then,
lookup tables have also been used to address various DT and ACPI quirks
like missing GPIOs and - as of recently - setting up shared GPIO proxy
devices.
The lookup itself stops when we find the first matching table for a
consumer and - if it doesn't contain the right entry - the lookup fails.
Since the tables can now be defined in multiple places and we can't know
how many there are, effectively limiting a consumer to only a single
lookup table is no longer viable.
Rework the code to always look through all tables matching the consumer.
Link: https://lore.kernel.org/r/20251222-gpio-shared-reset-gpio-proxy-v1-1-8d4bba7d8c14@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
A probe callback that just returns 0 does the same as not having a probe
callback at all. So gpio_stub_drv_probe() can be dropped without side
effects.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20251210070255.484169-2-u.kleine-koenig@baylibre.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
* Extend software node implementation, allowing its properties to reference
existing firmware nodes.
* Update the GPIO property interface to use reworked swnode macros.
* Rework reset-gpio code to use GPIO lookup via swnode.
* Fix spi-cs42l43 driver to work with swnode changes.
-----BEGIN PGP SIGNATURE-----
iI0EABYKADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCaR878xcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwBu+AQCw1iTmGlzqT+PqEXvWljTZeVDJ
GViCOX5rRSTTyuq8FwEAp6ToNopfJunQ/XQRdKHC0OX/aYtxo3eYI82LG9meSQ8=
=AMsz
-----END PGP SIGNATURE-----
Merge tag 'reset-gpio-for-v6.19' of https://git.pengutronix.de/git/pza/linux into gpio/for-next
Reset/GPIO/swnode changes for v6.19
* Extend software node implementation, allowing its properties to reference
existing firmware nodes.
* Update the GPIO property interface to use reworked swnode macros.
* Rework reset-gpio code to use GPIO lookup via swnode.
* Fix spi-cs42l43 driver to work with swnode changes.
Add better support for GPIOs shared by multiple consumers.
-----BEGIN PGP SIGNATURE-----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=fa8j
-----END PGP SIGNATURE-----
Merge tag 'gpio/shared-gpios-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux.git into gpio/for-next
Immutable branch between the GPIO, ASoC and regulator trees for v6.19-rc1
Add better support for GPIOs shared by multiple consumers.
Provide an interface allowing consumers to check if a GPIO descriptor
represents a GPIO that can potentially be shared by multiple consumers
at the same time. This is exposed to allow subsystems that already
work around the limitations of the current non-exclusive GPIO handling
in some ways, to gradually convert to relying on the new shared GPIO
feature of GPIOLIB.
Extend the gpiolib-shared module to mark the GPIO shared proxy
descriptors with a flag checked by the new interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-6-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As the final step in adding official support for shared GPIOs, enable
the previously added elements in core GPIO subsystem code. Set-up shared
GPIOs when adding a GPIO chip, tear it down on removal and check if a
GPIO descriptor looked up during the firmware-node stage is shared and
fall-back to machine lookup in this case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-5-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If the memory allocation in gpiolib_seq_start() fails, the s->private
field remains uninitialized and is later dereferenced without checking
in gpiolib_seq_stop(). Initialize s->private to NULL before calling
kzalloc() and check it before dereferencing it.
Fixes: e348544f79 ("gpio: protect the list of GPIO devices with SRCU")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20251103141132.53471-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reading the GPIO hardware number from a descriptor is a valid use-case
outside of the GPIO core. Export the symbol to consumers of GPIO
descriptors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20251016-aspeed-gpiolib-include-v1-2-31201c06d124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function takes a GPIO descriptor as first argument. Make its naming
consistent with the rest of the GPIO codebase and use the gpiod_ prefix.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20251016-aspeed-gpiolib-include-v1-1-31201c06d124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The chip_$level() macros take struct gpio_chip as argument so make it
follow the convention of using the 'gpiochip_' prefix.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We don't need to add additional logs when returning -ENOMEM so remove
unnecessary error messages.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder API
to other in-kernel users (to enable merging of a new pinctrl driver
that uses it)
- convert all remaining drivers to using the modernized generic GPIO chip
API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve its
support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO drivers
that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled with
COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmjaTpAACgkQEacuoBRx
13Iqwg//bcAxAcYGsEzMqcid9ugu+1KFiULWhgIYi4PBeX72UR7ZtSbzQ+hwTY68
Vs1W7eoeaglHwd46K/oXEBsnOvot/gQBjuw4QmYbO6viDWY9OuU81xppgAyw4IEx
wBmPiRVHHRNhcAA9/lu5OkFSWeeBNqcUkWlGgyUzsIIpQnadBRYXga+qFW9mq4m5
FMSCagsNP0tnRG4ae1Ek8SAbi3BiKaC/bpxukLVvv6Ma6CUktN2d49gW24h9NbKi
clflMVWgWgZBgYVk7Nmz5IQwYtvQz2M3y4Mb4VsuSWXWKRjX+gJb0knmq1fa8SEn
lx1MyhSgkpdtUx/bzLjZrPvesbiS1JnyLRAQVa+vtOU8ct2GSWjbKK9vY9w6guVT
KlptBNxxyQQi3WVtC+lvYz303gAlm5R2veehTMkmR6PIAE+zQ3EBNstiEEQsoMb2
npAqr/maodIo+FvUpFghSTfG2dSNRnXpRXmGzn49Y3LSjZu/7gC0B5mZYuGghK/g
UIvo3m40G/ajTUSyWOWPViUnJPkNMiQTHiH8MrXFUO/sbCavZCC2xp37D0ezWfIx
KRq3KPLHEL39dDvLFkpTQccOfSXch/bVFNX0X6EtfyAx4rSCphbX25IaWeuhJ9Ox
N3bALHVs0hMvY5nq0sUDTgf8oQMbpqKdAhKnSae3SBWLhon/EaA=
=TZ1G
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and support for more models in existing
ones.
The generic GPIO API has been reworked and all users converted
which allowed us to move the fields specific to the generic GPIO
implementation out of the high-level struct gpio_chip into its own
structure that wraps the gpio_chip.
Other than that, there's nothing too exciting. Mostly minor tweaks and
fixes all over the place, some refactoring and some small new features
in helper modules.
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and
pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder
API to other in-kernel users (to enable merging of a new pinctrl
driver that uses it)
- convert all remaining drivers to using the modernized generic GPIO
chip API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve
its support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO
drivers that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better
readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled
with COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding"
* tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (122 commits)
gpio: mpfs: fix setting gpio direction to output
gpio: generic: move GPIO_GENERIC_ flags to the correct header
gpio: generic: rename BGPIOF_ flags to GPIO_GENERIC_
gpio: nomadik: fix the debugfs helper stub
MAINTAINERS: Add entry on MAX7360 driver
input: misc: Add support for MAX7360 rotary
input: keyboard: Add support for MAX7360 keypad
gpio: max7360: Add MAX7360 gpio support
gpio: regmap: Allow to provide init_valid_mask callback
gpio: regmap: Allow to allocate regmap-irq device
pwm: max7360: Add MAX7360 PWM support
pinctrl: Add MAX7360 pinctrl driver
mfd: Add max7360 support
dt-bindings: mfd: gpio: Add MAX7360
rtc: Add Nuvoton NCT6694 RTC support
hwmon: Add Nuvoton NCT6694 HWMON support
watchdog: Add Nuvoton NCT6694 WDT support
can: Add Nuvoton NCT6694 CANFD support
i2c: Add Nuvoton NCT6694 I2C support
gpio: Add Nuvoton NCT6694 GPIO support
...
