Virtual wide planes give high amount of flexibility, but it is not
always enough:
In parallel multirect case only the half of the usual width is supported
for tiled formats. Thus the whole width of two tiled multirect
rectangles can not be greater than max_linewidth, which is not enough
for some platforms/compositors.
Another example is as simple as wide YUV plane. YUV planes can not use
multirect, so currently they are limited to max_linewidth too.
Now that the planes are fully virtualized, add support for allocating
two SSPP blocks to drive a single DRM plane. This fixes both mentioned
cases and allows all planes to go up to 2*max_linewidth (at the cost of
making some of the planes unavailable to the user).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/629026/
Link: https://lore.kernel.org/r/20241215-dpu-virtual-wide-v8-2-65221f213ce1@linaro.org
Only several SSPP blocks support such features as YUV output or scaling,
thus different DRM planes have different features. Properly utilizing
all planes requires the attention of the compositor, who should
prefer simpler planes to YUV-supporting ones. Otherwise it is very easy
to end up in a situation when all featureful planes are already
allocated for simple windows, leaving no spare plane for YUV playback.
To solve this problem make all planes virtual. Each plane is registered
as if it supports all possible features, but then at the runtime during
the atomic_check phase the driver selects backing SSPP block for each
plane.
As the planes are attached to the CRTC and not the encoder, the SSPP
blocks are also allocated per CRTC ID (all other resources are currently
allocated per encoder ID). This also matches the hardware requirement,
where both rectangles of a single SSPP can only be used with the LM
pair.
Note, this does not provide support for using two different SSPP blocks
for a single plane or using two rectangles of an SSPP to drive two
planes. Each plane still gets its own SSPP and can utilize either a solo
rectangle or both multirect rectangles depending on the resolution.
Note #2: By default support for virtual planes is turned off and the
driver still uses old code path with preallocated SSPP block for each
plane. To enable virtual planes, pass 'msm.dpu_use_virtual_planes=1'
kernel parameter.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/629022/
Link: https://lore.kernel.org/r/20241215-dpu-virtual-wide-v8-1-65221f213ce1@linaro.org
On chipsets such as QCS615, there is no 3dmux present. In such
a case, a layer exceeding the max_mixer_width cannot be split,
hence cannot be supported.
Filter out the modes which exceed the max_mixer_width when there
is no 3dmux present. Also, add a check in the dpu_crtc_atomic_check()
to return failure for such modes.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Xiangxu Yin <quic_xiangxuy@quicinc.com> # QCS615
Patchwork: https://patchwork.freedesktop.org/patch/627974/
Link: https://lore.kernel.org/r/20241209-no_3dmux-v3-1-48aaa555b0d3@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Every layer of vop2 should bind a window, and we also need to make
sure that this window is not used by other layer.
0x5 is a reserved layer sel value on rk3568, but it will select
Cluster3 on rk3588, configure unused layers to 0x5 will lead
alpha blending error on rk3588.
When we bind a window from layerM to layerN, we move the old window
on layerN to layerM.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214081719.3330518-3-andyshrk@163.com
The company name has update to Rockchip Electronics Co., Ltd.
since 2021.
And change Co.Ltd to Co., Ltd. to fix mail server warning:
DBL_SPAM(6.50)[co.ltd:url];
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214071333.3325308-1-andyshrk@163.com
Toolchain and infrastructure:
- Set bindgen's Rust target version to prevent issues when pairing
older rustc releases with newer bindgen releases, such as
bindgen >= 0.71.0 and rustc < 1.82 due to unsafe_extern_blocks.
drm/panic:
- Remove spurious empty line detected by a new Clippy warning.
-----BEGIN PGP SIGNATURE-----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=PU27
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-6.13' of https://github.com/Rust-for-Linux/linux
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Set bindgen's Rust target version to prevent issues when
pairing older rustc releases with newer bindgen releases,
such as bindgen >= 0.71.0 and rustc < 1.82 due to
unsafe_extern_blocks.
drm/panic:
- Remove spurious empty line detected by a new Clippy warning"
* tag 'rust-fixes-6.13' of https://github.com/Rust-for-Linux/linux:
rust: kbuild: set `bindgen`'s Rust target version
drm/panic: remove spurious empty line to clean warning
On gt reset, if a context is running, then accumulate it's active time
into the busyness counter since there will be no chance for the context
to switch out and update it's run time.
v2: Move comment right above the if (John)
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-4-umesh.nerlige.ramappa@intel.com
Active busyness of an engine is calculated using gt timestamp and the
context switch in time. While capturing the gt timestamp, it's possible
that the context switches out. This race could result in an active
busyness value that is greater than the actual context runtime value by a
small amount. This leads to a negative delta and throws off busyness
calculations for the user.
If a subsequent count is smaller than the previous one, just return the
previous one, since we expect the busyness to catch up.
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-3-umesh.nerlige.ramappa@intel.com
On GT reset, we store total busyness counts for all engines and
re-register the utilization buffer with GuC. At that time we should
reset the buffer, so that we don't get spurious busyness counts on
subsequent queries.
To repro this issue, run igt@perf_pmu@busy-hang followed by
igt@perf_pmu@most-busy-idle-check-all for a couple iterations.
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-2-umesh.nerlige.ramappa@intel.com
There is a mesa debug tool for decoding devcoredump files. Recent
changes to improve the devcoredump output broke that tool. So revert
the changes until the tool can be extended to support the new fields.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Fixes: c28fd6c358 ("drm/xe/devcoredump: Improve section headings and add tile info")
Fixes: ec1455ce7e ("drm/xe/devcoredump: Add ASCII85 dump helper function")
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Julia Filipchuk <julia.filipchuk@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-xe@lists.freedesktop.org
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213172833.1733376-1-John.C.Harrison@Intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Expose functions to request and free MSI-X interrupts.
The request has two flavors:
- Static MSI-X allocation, for known MSI-X interrupts (e.g. GuC-to-host)
- Dynamic MSI-X allocation, which uses the next available MSI-X interrupt
Signed-off-by: Ilia Levi <ilia.levi@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213072538.6823-4-ilia.levi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
- Configure the HW engines to work with MSI-X
- Program the LRC to use memirq infra (similar to VF)
- CS_INT_VEC field added to the LRC
Bspec: 60342, 72547
Signed-off-by: Ilia Levi <ilia.levi@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213072538.6823-3-ilia.levi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A new flow is added for devices that support MSI-X:
- MSI-X vector 0 is used for GuC-to-host interrupt
- MSI-X vector 1 (aka default MSI-X) is used for HW engines
The default MSI-X will be passed to the HW engines in a subsequent
patch.
Signed-off-by: Ilia Levi <ilia.levi@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213072538.6823-2-ilia.levi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Liu Ying <victor.liu@nxp.com> # ite-it6263.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204105827.1682632-2-u.kleine-koenig@baylibre.com
Instead of returning a generic NULL on error from
drm_dp_tunnel_mgr_create(), use error pointers with informative codes
to align the function with stub that is executed when
CONFIG_DRM_DISPLAY_DP_TUNNEL is unset. This will also trigger IS_ERR()
in current caller (intel_dp_tunnerl_mgr_init()) instead of bypassing it
via NULL pointer.
v2: use error codes inside drm_dp_tunnel_mgr_create() instead of handling
on caller's side (Michal, Imre)
v3: fixup commit message and add "CC"/"Fixes" lines (Andi),
mention aligning function code with stub
Fixes: 91888b5b1a ("drm/i915/dp: Add support for DP tunnel BW allocation")
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7q4fpnmmztmchczjewgm6igy55qt6jsm7tfd4fl4ucfq6yg2oy@q4lxtsu6445c
Include <linux/of.h> directly to get of_property_read_string_index().
Avoids the proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-7-tzimmermann@suse.de
Include <linux/property.h> directly to get device_property_read_u32().
Avoids the proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-6-tzimmermann@suse.de
Include <linux/mod_devicetable.h> directly to get struct of_device_id.
Avoids the proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-5-tzimmermann@suse.de
Include <linux/mod_devicetable.h> directly to get struct of_device_id.
Avoids the proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-4-tzimmermann@suse.de
Include <linux/of.h> directly to get of_device_is_available(). Avoids
the proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-3-tzimmermann@suse.de
Include <linux/of.h> directly to get of_parse_phandle(). Avoids the
proxy include via <linux/backlight.h>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241011144632.90434-2-tzimmermann@suse.de
The shutdown function can be called when the display is already
unprepared. For example during reboot this trigger a kernel
backlog. Calling the drm_panel_unprepare, allow us to avoid
to trigger the kernel warning.
Fixes: 2e87bad7cd ("drm/panel: Add Synaptics R63353 panel driver")
Tested-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://lore.kernel.org/r/20241205163002.1804784-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241205163002.1804784-1-dario.binacchi@amarulasolutions.com
Similar to the r_pipe sspp protect, add a check to protect
the pipe state prints to avoid NULL ptr dereference for cases when
the state is dumped without a corresponding atomic_check() where the
pipe->sspp is assigned.
Fixes: 31f7148fd3 ("drm/msm/dpu: move pstate->pipe initialization to dpu_plane_atomic_check")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/67
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # sc7180-trogdor
Patchwork: https://patchwork.freedesktop.org/patch/628404/
Link: https://lore.kernel.org/r/20241211-check-state-before-dump-v2-1-62647a501e8c@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
During suspend/resume process all connectors are explicitly disabled and
then reenabled. However resume fails because of the connector_status check:
[dpu error]connector not connected 3
[drm:drm_mode_config_helper_resume [drm_kms_helper]] *ERROR* Failed to resume (-22)
It doesn't make sense to check for the Writeback connected status (and
other drivers don't perform such check), so drop the check.
It wasn't a problem before the commit 71174f362d ("drm/msm/dpu: move
writeback's atomic_check to dpu_writeback.c"), since encoder's
atomic_check() is called under a different conditions that the
connector's atomic_check() (e.g. it is not called if there is no
connected CRTC or if the corresponding connector is not a part of the
new state).
Fixes: 71174f362d ("drm/msm/dpu: move writeback's atomic_check to dpu_writeback.c")
Cc: stable@vger.kernel.org
Reported-by: Leonard Lausen <leonard@lausen.nl>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/57
Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor
Tested-by: György Kurucz <me@kuruczgy.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # Trogdor (sc7180)
Patchwork: https://patchwork.freedesktop.org/patch/627828/
Link: https://lore.kernel.org/r/20241209-dpu-fix-wb-v4-1-7fe93059f9e0@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
dp_ctrl_off_link() was created to handle a case where we received
a cable connect and then get a cable disconnect without the corresponding
dp_display_enable(). For such cases the pixel clock will be off but the
link clock will still be on. dp_ctrl_off_link() handles this case by
turning off the link clock only.
However, the vote removal to the opp table for this case was missed.
Remove the opp table vote in dp_ctrl_off_link().
Fixes: 375a126090 ("drm/msm/dp: tear down main link at unplug handle immediately")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/627487/
Link: https://lore.kernel.org/r/20241205-dp_mst-v1-2-f8618d42a99a@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>