Patch series "New page table range API", v6.
This patchset changes the API used by the MM to set up page table entries.
The four APIs are:
set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)
flush_dcache_folio() isn't technically new, but no architecture
implemented it, so I've done that for them. The old APIs remain around
but are mostly implemented by calling the new interfaces.
The new APIs are based around setting up N page table entries at once.
The N entries belong to the same PMD, the same folio and the same VMA, so
ptep++ is a legitimate operation, and locking is taken care of for you.
Some architectures can do a better job of it than just a loop, but I have
hesitated to make too deep a change to architectures I don't understand
well.
One thing I have changed in every architecture is that PG_arch_1 is now a
per-folio bit instead of a per-page bit when used for dcache clean/dirty
tracking. This was something that would have to happen eventually, and it
makes sense to do it now rather than iterate over every page involved in a
cache flush and figure out if it needs to happen.
The point of all this is better performance, and Fengwei Yin has measured
improvement on x86. I suspect you'll see improvement on your architecture
too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/20230206140639.538867-5-fengwei.yin@intel.com/
You'll need to run it on an XFS filesystem and have
CONFIG_TRANSPARENT_HUGEPAGE set.
This patchset is the basis for much of the anonymous large folio work
being done by Ryan, so it's received quite a lot of testing over the last
few months.
This patch (of 38):
Determine if a value lies within a range more efficiently (subtraction +
comparison vs two comparisons and an AND). It also has useful (under some
circumstances) behaviour if the range exceeds the maximum value of the
type. Convert all the conflicting definitions of in_range() within the
kernel; some can use the generic definition while others need their own
definition.
Link: https://lkml.kernel.org/r/20230802151406.3735276-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230802151406.3735276-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
define fix, a recursive lock fix for dma-buf, a shader validation fix
and a reference counting fix for vmwgfx
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZOcXnQAKCRDj7w1vZxhR
xZNZAP9d5ouL/6qcxM/y2+Wi2wa+zTtC8jsRl5pPnkxs9Rra6gEA7jelHrJBKbFP
MPs9vojtSwCmtITed49os+Emsz4fOgE=
=rpTN
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2023-08-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A samsung-dsim initialization fix, a devfreq fix for panfrost, a DP DSC
define fix, a recursive lock fix for dma-buf, a shader validation fix
and a reference counting fix for vmwgfx
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/amy26vu5xbeeikswpx7nt6rddwfocdidshrtt2qovipihx5poj@y45p3dtzrloc
The prev pointer in __drm_gpuva_sm_map() was used to implement automatic
merging of mappings. Since automatic merging did not make its way
upstream, remove this leftover.
Fixes: e6303f323b ("drm: manager to keep track of GPUs VA mappings")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823233119.2891-1-dakr@redhat.com
port_clock is what the encoder/dpll code is supposed to calculate,
it is not the input clock. Use the dotclock as the target we're
trying to achieve instead.
TODO: the SDVO TV clocking is a mess atm and needs further work
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-7-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Call *_calc_dpll_params() even in cases where the encoder has
computed the DPLL params for us.
The SDVO TV output code doesn't populate crtc_state->dpll.dot
leading to the dotclock getting calculated as zero, and that
leads to all kinds of real problems. The g4x DP code also
doesn't populate the derived dividers nor .vco, which could
also create some confusion.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Allow *_calc_dpll_params() to be called even if the N/P dividers
are zero without warning. We'll want to call these to make sure the
derived values are fully computed, but not all users (VLV DSI in
particular) even enable the DPLL and thus the dividers will
be left at zero.
It could also be possible that the BIOS has misprogrammed the DPLL
(IIRC happened with some SNB machines with 4k+ displays) and thus
we'll currently generate a lot of dmesg spew. Better be silent and
just let the normal state checker/etc. deal with any driver bugs.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The SDVO inputs are reported a simple number, not a bitmask.
Adjust the code to match reality.
Note that we don't actually support dual input SDVO devices,
and we just always use the first input.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I have at least one SDVO device (some Lenovo DVI-I ADD2 card,
based on Conexant CX25904) where GetAttachedDisplays returns
success but fails to report any attached displays unless we
precede the command with a SetTargetOutput. Make it so.
I wasn't able to spot anything in the SDVO spec stating that
this should be necessary, but real world wins over spec.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/drm_connector.c:2215: warning: Function parameter or member 'supported_colorspaces' not described in 'drm_mode_create_hdmi_colorspace_property'
drivers/gpu/drm/drm_connector.c:2239: warning: Function parameter or member 'supported_colorspaces' not described in 'drm_mode_create_dp_colorspace_property'
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230824073710.2677348-17-lee@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Currently, NO_PREFETCH is passed implicitly through
drm_nouveau_gem_pushbuf_push::length and drm_nouveau_exec_push::va_len.
Since this is a direct representation of how the HW is programmed it
isn't really future proof for a uAPI. Hence, fix this up for the new
uAPI and split up the va_len field of struct drm_nouveau_exec_push,
such that we keep 32bit for va_len and 32bit for flags.
For drm_nouveau_gem_pushbuf_push::length at least provide
NOUVEAU_GEM_PUSHBUF_NO_PREFETCH to indicate the bit shift.
While at it, fix up nv50_dma_push() as well, such that the caller
doesn't need to encode the NO_PREFETCH flag into the length parameter.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823181746.3446-1-dakr@redhat.com
If a sched job depends on a dma-fence from a job from the same GPU
scheduler instance, but a different scheduler entity, the GPU scheduler
does only wait for the particular job to be scheduled, rather than for
the job to fully complete. This is due to the GPU scheduler assuming
that there is a scheduler instance per ring. However, the current
implementation, in order to avoid arbitrary amounts of kthreads, has a
single scheduler instance while scheduler entities represent rings.
As a workaround, set the DRM_SCHED_FENCE_DONT_PIPELINE for all
out-fences in order to force the scheduler to wait for full job
completion for dependent jobs from different entities and same scheduler
instance.
There is some work in progress [1] to address the issues of firmware
schedulers; once it is in-tree the scheduler topology in Nouveau should
be re-worked accordingly.
[1] https://lore.kernel.org/dri-devel/20230801205103.627779-1-matthew.brost@intel.com/
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collaboralcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20230811010632.2473-1-dakr@redhat.com
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
Currently, NO_PREFETCH is passed implicitly through
drm_nouveau_gem_pushbuf_push::length and drm_nouveau_exec_push::va_len.
Since this is a direct representation of how the HW is programmed it
isn't really future proof for a uAPI. Hence, fix this up for the new
uAPI and split up the va_len field of struct drm_nouveau_exec_push,
such that we keep 32bit for va_len and 32bit for flags.
For drm_nouveau_gem_pushbuf_push::length at least provide
NOUVEAU_GEM_PUSHBUF_NO_PREFETCH to indicate the bit shift.
While at it, fix up nv50_dma_push() as well, such that the caller
doesn't need to encode the NO_PREFETCH flag into the length parameter.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823181746.3446-1-dakr@redhat.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmTiDvweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7doH/2Poj73npPKPVfT3
RF8AsgvAj2pLby67rdvwTdFX+exS63SsuwtGGRfAHfGabiwmNN+oT2dLb0aY15bp
nskHnFpcqQ/pfZ2i2rUCenzBX8S9QULvPidLKRaf1FcSdOzqd97Bw5oDPMtzqy/R
Pm+Dzs//7fYvtm69nt6hKW4d6wXxNcg7Fk/QgoJ5Ax9vGvDuZmWXH0ZgBf/5kH04
TTPQNtVX57lf+FHugkhFEn4JbYXvN168b+LuX2PHwOeG/8AIS69Hc0vgvhHNAycT
mmpUI1gWA2jfrJ2RCyyezF/6wy9Ocsp+CbPjfwjuRUxOk0XIm1+cp9Mlz/cRbMsZ
f0tOTpk=
=xrJp
-----END PGP SIGNATURE-----
BackMerge tag 'v6.5-rc7' into drm-next
Linux 6.5-rc7
This is needed for the CI stuff and the msm pull has fixes in it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).
After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.
Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.
Fixes: d33a54e399 ("drm/probe_helper: sort out poll_running vs poll_enabled")
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
(cherry picked from commit 50452f2f76)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).
This is needed by the next patch fixing HPD polling on i915.
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
(cherry picked from commit fe2352fd64)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).
After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.
Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.
Fixes: d33a54e399 ("drm/probe_helper: sort out poll_running vs poll_enabled")
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
(cherry picked from commit 50452f2f76)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).
This is needed by the next patch fixing HPD polling on i915.
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
(cherry picked from commit fe2352fd64)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).
After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.
Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.
Fixes: d33a54e399 ("drm/probe_helper: sort out poll_running vs poll_enabled")
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).
This is needed by the next patch fixing HPD polling on i915.
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
vmw_bo_unreference sets the input buffer to null on exit, resulting in
null ptr deref's on the subsequent drm gem put calls.
This went unnoticed because only very old userspace would be exercising
those paths but it wouldn't be hard to hit on old distros with brand
new kernels.
Introduce a new function that abstracts unrefing of user bo's to make
the code cleaner and more explicit.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reported-by: Ian Forbes <iforbes@vmware.com>
Fixes: 9ef8d83e8e ("drm/vmwgfx: Do not drop the reference to the handle too soon")
Cc: <stable@vger.kernel.org> # v6.4+
Reviewed-by: Maaz Mombasawala<mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230818041301.407636-1-zack@kde.org
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct clk_hw_onecell_data.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Qin Jian <qinjian@cqplus1.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-sunxi@lists.linux.dev
Cc: linux-phy@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230817203019.never.795-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If GuC hits an internal error (and survives long enough to report it
to the KMD), it is basically toast and will stop until a GT reset and
subsequent GuC reload is performed. Previously, the KMD just printed
an error message and then waited for the heartbeat to eventually kick
in and trigger a reset (assuming the heartbeat had not been disabled).
Instead, force the reset immediately to guarantee that it happens and
to eliminate the very long heartbeat delay. The captured error state
is also more likely to be useful if captured at the time of the error
rather than many seconds later.
Note that it is not possible to trigger a reset from with the G2H
handler itself. The reset prepare process involves flushing
outstanding G2H contents. So a deadlock could result. Instead, the G2H
handler queues a worker thread to do the reset asynchronously.
v2: Flush the worker on suspend and shutdown. Add rate limiting to
prevent spam from a totally dead system (review feedback from Daniele).
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230816003957.3572654-1-John.C.Harrison@Intel.com
If a sched job depends on a dma-fence from a job from the same GPU
scheduler instance, but a different scheduler entity, the GPU scheduler
does only wait for the particular job to be scheduled, rather than for
the job to fully complete. This is due to the GPU scheduler assuming
that there is a scheduler instance per ring. However, the current
implementation, in order to avoid arbitrary amounts of kthreads, has a
single scheduler instance while scheduler entities represent rings.
As a workaround, set the DRM_SCHED_FENCE_DONT_PIPELINE for all
out-fences in order to force the scheduler to wait for full job
completion for dependent jobs from different entities and same scheduler
instance.
There is some work in progress [1] to address the issues of firmware
schedulers; once it is in-tree the scheduler topology in Nouveau should
be re-worked accordingly.
[1] https://lore.kernel.org/dri-devel/20230801205103.627779-1-matthew.brost@intel.com/
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collaboralcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20230811010632.2473-1-dakr@redhat.com
When getting the next gt's seqno to be stored into an
objects mm.tlb[gt_id] array, fix the retrieval code
to get it from the correct gt instead of the same one.
Fixes: d6c531ab48 ("drm/i915: Invalidate the TLBs on each GT")
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814182449.1060747-1-alan.previn.teres.alexis@intel.com
(cherry picked from commit 90b8ad1353)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
System wide suspend already has support for lmem save/restore during
suspend therefore enabling d3cold for s2idle and keepng it disable for
runtime PM.(Refer below commit for d3cold runtime PM disable justification)
'commit 66eb93e71a ("drm/i915/dgfx: Keep PCI autosuspend control
'on' by default on all dGPU")'
It will reduce the DG2 Card power consumption to ~0 Watt
for s2idle power KPI.
v2:
- Added "Cc: stable@vger.kernel.org".
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8755
Cc: stable@vger.kernel.org
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jianshui Yu <Jianshui.yu@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230816125216.1722002-1-anshuman.gupta@intel.com
(cherry picked from commit 2643e6d1f2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>