If the size of the packets would change during the transmission, it could
happen that some retries of packets are overlapping. In this case, precise
comparisons of sequence numbers by the receiver would be wrong. It is then
necessary to check if the start sequence number to the end sequence number
("seqno + length") would contain a new range.
If this is the case then this is enough to accept this packet. In all other
cases, the packet still has to be dropped (and not acked).
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When last_recv is updated to store the last receive sequence number, it is
assuming that nothing is modifying in parallel while:
* check for outdated packets is done
* out of order check is performed (and packets are stored in out-of-order
queue)
* the out-of-order queue was searched for closed gaps
* sequence number for next ack is calculated
Nothing of that was actually protected. It could therefore happen that the
last_recv was updated multiple times in parallel and the final sequence
number was calculated with deltas which had no connection to the sequence
number they were added to.
Lock this whole region with the same lock which was already used to protect
the unacked (out-of-order) list.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The last_recv_time field for batadv_tp_receiver tracks the jiffies value of
the most recent activity and is used to detect timeouts. These accesses are
not consistently protected by a lock, so READ_ONCE/WRITE_ONCE must be used
to prevent data races caused by compiler optimizations.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the unacked_list is unbound, an attacker could send messages with
small lengths and appropriated seqno + gaps to force the receiver to
allocate more and more unacked_list entries. And the end either causing an
out-of-memory situation or increase the management overhead for the (large)
list that significant portions of CPU cycles are wasted in searching
through the list.
When limiting the list to a specific number, it is important to still
correctly add a new entry to the list. But if the list became larger than
the limit, the last entry of the list (with the highest seqno) must be
dropped to still allow the earlier seqnos to finish and therefore to
continue the process. Otherwise, the process might get stuck with too high
seqnos which are not handled by batadv_tp_ack_unordered().
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The tp_meter codebase was recently refactored:
* throughput meter sender and receiver variables were split into
two different structures
* the congestion control variables were extracted in a separate structure
But the kernel-doc was not updated everywhere to reflect these changes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
With commit 86898fa6b8 ("workqueue: Implement disable/enable for
(delayed) work items"), work queues gained the ability to permanently
disallow re-queuing of work items. This is particularly important during
object teardown, where a work item must not be re-armed after shutdown
begins.
Convert all cancel_work_sync() and cancel_delayed_work_sync() call sites to
their disable_* equivalents to clarify the intent to prevent re-arming
after teardown.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The last_recv_time is the most important indicator for a receiver session
to figure out whether a session timed out or not. But this information was
only initialized after the session was added to the tp_receiver_list and
after the timer was started.
In the worst case, the timer (function) could have tried to access this
information before the actual initialization was reached. Like rest of the
variables of the tp_meter receiver session, this field has to be filled out
before any other (parallel running) context has the chance to access it.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Congestion control variables in batadv_tp_sender were scattered across the
struct without clear grouping, making it difficult to reason about which
fields require cwnd_lock (now "cc_lock") protection. These should be
combined in a structure to make it more easily visible which variable
should be read/modified with the cc_lock held.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some variables used atomic_t for concurrent access while others relied on
cwnd_lock, leading to an inconsistent locking model. This can be simplified
by:
* keeping all congestion control decisions inside the cc_lock
* variables which can be accessed without a lock must use
READ_ONCE/WRITE_ONE
This is only possible, by extracting the congestion control logic from
batadv_tp_recv_ack() into a new helper batadv_tp_handle_ack(). Its
decisions are returned as a batadv_tp_ack_reaction enum value and then
applied by the caller. This separates the algorithm (deciding what to do)
from the mechanism (actually doing it).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The monolithic batadv_tp_vars struct holds fields for both sender and
receiver roles, distinguished only by a runtime enum role. This makes it
easy to accidentally access a field intended for the opposite role, since
neither the compiler nor the type system provide any guard against such
mistakes. The role check also adds unnecessary branching in several code
paths.
Introduce batadv_tp_vars_common to hold fields shared across both roles,
then derive two separate types (sender/receiver) from it. The functions can
operate on them without any ambiguity about the available fields. This also
reduces the memory footprint of receiver sessions, which no longer carry
the substantial sender-only fields.
Care must be taken to prevent concurrent TP sessions between the same two
peers in opposite directions, since sender and receiver sessions are now
tracked in separate lists and a lookup in one list no longer detects a
session in the other.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the receiver variables (aka "session") are initialized, then they are
added to the list of sessions before the timer is set up. A RCU protected
reader could therefore find the entry and run mod_setup before
batadv_tp_init_recv() finished the timer initialization.
The same is true for batadv_tp_start(), which must first initialize the
finish_work and the test_length to avoid a similar problem.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The recover variable and the last_sent sequence number are initialized on
purpose as a really high value which will wrap-around after the first 2000
bytes. The fast recovery precondition must therefore not use simple integer
comparisons but use helpers which are aware of the sequence number
wrap-arounds.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The fast recovery precondition checks if the recover (initialized to
BATADV_TP_FIRST_SEQ) is bigger than the received ack. But since recover is
only updated when this check is successful, it will never enter the fast
recovery mode.
According to RFC6582 Section 3.2 step 2, the check should actually be
different:
> When the third duplicate ACK is received, the TCP sender first
> checks the value of recover to see if the Cumulative
> Acknowledgment field covers more than recover
The precondition must therefore check if recover is smaller than the
received ack - basically swapping the operands of the current check.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The cwnd is always MSS <= cwnd <= 0x20000000. But the calculation in
batadv_tp_update_cwnd() assumes unsigned 32 bit arithmetics.
((mss * 8) ** 2) / (cwnd * 8)
In case cwnd is actually 0x20000000, it will be shifted by 3 bit to the
left end up at 0x100000000 or U32_MAX + 1. It will therefore wrap around
and be 0 - resulting in:
((mss * 8) ** 2) / 0
This is of course invalid and cannot be calculated. The calculation should
must be simplified to avoid this overflow:
(mss ** 2) * 8 / cwnd
It will keep the precision enhancement from the scaling (by 8) but avoid
the overflow in the divisor.
In theory, there could still be an overflow in the dividend. It is at the
moment fixed to BATADV_TP_PLEN in batadv_tp_recv_ack() - so it is not an
imminent problem. But allowing it to use the whole u32 bit range, would
mean that it can still use up to 67 bits. To keep this calculation safe for
32 bit arithmetic, mss must never use more than floor((32 - 3) / 2) bits -
or in other words: must never be larger than 16383.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
In batadv_tp_avail(), win_left is calculated with 32-bit unsigned
arithmetic: win_left = win_limit - tp_vars->last_sent;
During Fast Recovery, cwnd is inflated and last_sent advances rapidly. When
Fast Recovery ends, cwnd drops abruptly back to ss_threshold. If the newly
shrunk win_limit is less than last_sent, the unsigned subtraction will
underflow, wrapping to a massive positive value. Instead of returning that
the window is full (unavailable), it returns that the sender can continue
sending.
To handle this situation, it must be checked whether the windows end
sequence number (win_limit) has to be compared with the last sent sequence
number. If it would be before the last sent sequence number, then more acks
are needed before the transmission can be started again.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When batadv_tp_update_cwnd() is called, dec_cwnd is increased. But dec_cwnd
is only initialixed (to 0) when a duplicate Ack was received or when cwnd
is below the ss_threshold.
Just initialize the cwnd during the initialization to avoid any potential
access of uninitialized data.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When an ack with a sequence number equal to the last_acked is received, the
dup_acks counter is increased to decide whether fast retransmit should be
performed. Only when the sequence numbers are not equal, the dup_acks is
set to the initial value (0).
But if the initial packet would have the sequence number
BATADV_TP_FIRST_SEQ, dup_acks would not be initialized and atomic_inc would
operate on an undefined starting value. It is therefore required to have it
explicitly initialized during the start of the sender session.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When batadv_tp_handle_out_of_order inserts a new entry in the list of
unacked (out of order) packets, it searches from the entry with the newest
sequence number towards oldest sequence number. If an entry is found which
is older than the newly entry, the new entry has to be added after the
found one to keep the ascending order.
But for this operation list_add_tail() was used. But this function adds an
entry _before_ another one. As result, the list would contain a lot of
swapped sequence numbers. The consumer of this list
(batadv_tp_ack_unordered()) would then fail to correctly ack packets.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The mesh state is only accessed as plain loads/stores and does not require
full atomic_t semantics. Convert to an enum and replace its users with
READ_ONCE()/WRITE_ONCE() to avoid load/store tearing.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Session lookups in tp_list matched only on destination address (and
optionally session ID), leaving role validation to the caller. If two
sessions with the same other_end coexisted (one as sender, one as receiver)
a lookup could silently return the wrong one, causing the caller's role to
bail out early, potentially skipping necessary cleanup.
Move the role check into the lookup functions themselves so the correct
entry is always returned, or none at all. Since batadv_tp_start()
legitimately needs to detect any active session to a destination regardless
of role, introduce a dedicated helper for that case rather than bending the
existing lookup semantics.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batadv_tp_sender_shutdown() previously used two separate variables to track
session state: sending (an atomic flag indicating whether the session was
active) and reason (a plain enum storing the stop reason). This introduced
a race window between the two writes: after sending was cleared to 0,
batadv_tp_send() could observe the stopped state and call
batadv_tp_sender_end() before reason was written, causing the wrong stop
reason to be reported to the caller.
Fix this by consolidating both variables into a single atomic send_result,
which holds 0 while the session is running and the stop reason once it
ends.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by
timer_delete() to guard against the timer handler re-arming itself between
the two calls. This double-deletion hack relied on the sending status being
set to 0 to suppress re-arming.
Replace both calls with a single timer_shutdown_sync(). This function both
waits for any running timer callback to complete (like timer_delete_sync())
and permanently disarms the timer so it cannot be re-armed afterwards,
making re-arming prevention unconditional and self-documenting.
The re-arming property is also required because otherwise:
1. context 0 (batadv_tp_recv_ack()) checks in
batadv_tp_reset_sender_timer() if sending is still 1 -> it is
2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in
this process forces the kthread to stop timer in
batadv_tp_sender_cleanup()
3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the
timer -> but the reference for it is already gone
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batadv_tp_recv_ack() and batadv_tp_stop() are only valid for tp_vars in the
BATADV_TP_SENDER role. When called with a BATADV_TP_RECEIVER role, it
proceeds to read sender-only members that were never initialized, leading
to undefined behavior.
This can be triggered when a node that is currently acting as a receiver in
an ongoing tp_meter session receives a malicious ACK packet.
Guard against this by checking tp_vars->role immediately after the
lookup and bailing out if it is not BATADV_TP_SENDER, before any of
those members are accessed.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Reviewed-by: Yuan Tan <yuantan098@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The receiver shutdown timer handler, batadv_tp_receiver_shutdown(), is
responsible for releasing the tp_vars reference it holds. However, the
existing logic for coordinating this release with batadv_tp_stop_all() was
flawed.
timer_shutdown_sync() guarantees the timer will not fire again after it
returns, but it returns non-zero only when the timer was pending at the
time of the call. If the timer had already expired (and
batadv_tp_stop_all() would unsucessfully try to rearm itself),
batadv_tp_stop_all() skips its batadv_tp_vars_put(), and
batadv_tp_receiver_shutdown() fails to put its own reference as well.
Fix this by introducing a new atomic variable receiving that is set to 1
when the receiver is initialized and cleared atomically with atomic_xchg()
by whichever side claims it first. Only the side that observes the
transition from 1 to 0 is responsible for releasing the tp_vars timer
reference, eliminating the uncertainty.
Cc: stable@kernel.org
Fixes: 3d3cf6a731 ("batman-adv: stop tp_meter sessions during mesh teardown")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batadv_tp_sender_shutdown() unconditionally decrements the "sending"
atomic counter. If multiple paths (e.g. timeout, user cancel, and
normal finish) call this function, the counter can underflow to -1.
Since the sender logic treats any non-zero value as "still sending",
a negative value causes the sender kthread to loop indefinitely.
This leads to a use-after-free when the interface is removed while
the zombie thread is still active.
Fix this by using atomic_xchg() to ensure the counter only transitions
from 1 to 0 once.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Luxiao Xu <rakukuip@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
[sven: added missing change in batadv_tp_send]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When batadv_tp_start() or batadv_tp_init_recv() fail to allocate a new
tp_vars object, the previously incremented bat_priv->tp_num counter is
never decremented. This causes tp_num to drift upward on each allocation
failure. Since only BATADV_TP_MAX_NUM sessions can be started and the count
is never reduced for these failed allocations, it causes to an exhaustion
of throughput meter sessions. In worst case, no new throughput meter
session can be started until the mesh interface is removed.
The error handling must decrement tp_num releasing the lock and aborting
the creation of an throughput meter session
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
TP meter sessions remain linked on bat_priv->tp_list after the netlink
request has already finished. When the mesh interface is removed,
batadv_mesh_free() currently tears down the mesh without first draining
these sessions.
A running sender thread or a late incoming tp_meter packet can then keep
processing against a mesh instance which is already shutting down.
Synchronize tp_meter with the mesh lifetime by stopping all active
sessions from batadv_mesh_free() and waiting for sender threads to exit
before teardown continues.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Co-developed-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Jiexun Wang <wangjiexun2025@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Prevent tp_meter from starting new sender or receiver sessions after
mesh_state has left BATADV_MESH_ACTIVE.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Co-developed-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Luxing Yin <tr0jan@lzu.edu.cn>
Signed-off-by: Jiexun Wang <wangjiexun2025@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The way how the virtual interface is called inside the batman-adv source
code is not consistent. The genl headers call it meshif and the rest of the
code calls is (mostly) softif.
The genl definitions cannot be touched because they are part of the UAPI.
But the rest of the batman-adv code can be touched to have a consistent
name again.
The bulk of the renaming was done using
sed -i -e 's/soft\(-\|\_\| \|\)i\([nf]\)/mesh\1i\2/g' \
-e 's/SOFT\(-\|\_\| \|\)I\([NF]\)/MESH\1I\2/g'
and then it was adjusted slightly when proofreading the changes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit d2a8ebbf81 ("kernel.h: split out container_of() and
typeof_member() macros") introduced a new header for the container_of
related macros from (previously) linux/kernel.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Pull exit cleanups from Eric Biederman:
"While looking at some issues related to the exit path in the kernel I
found several instances where the code is not using the existing
abstractions properly.
This set of changes introduces force_fatal_sig a way of sending a
signal and not allowing it to be caught, and corrects the misuse of
the existing abstractions that I found.
A lot of the misuse of the existing abstractions are silly things such
as doing something after calling a no return function, rolling BUG by
hand, doing more work than necessary to terminate a kernel thread, or
calling do_exit(SIGKILL) instead of calling force_sig(SIGKILL).
In the review a deficiency in force_fatal_sig and force_sig_seccomp
where ptrace or sigaction could prevent the delivery of the signal was
found. I have added a change that adds SA_IMMUTABLE to change that
makes it impossible to interrupt the delivery of those signals, and
allows backporting to fix force_sig_seccomp
And Arnd found an issue where a function passed to kthread_run had the
wrong prototype, and after my cleanup was failing to build."
* 'exit-cleanups-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (23 commits)
soc: ti: fix wkup_m3_rproc_boot_thread return type
signal: Add SA_IMMUTABLE to ensure forced siganls do not get changed
signal: Replace force_sigsegv(SIGSEGV) with force_fatal_sig(SIGSEGV)
exit/r8188eu: Replace the macro thread_exit with a simple return 0
exit/rtl8712: Replace the macro thread_exit with a simple return 0
exit/rtl8723bs: Replace the macro thread_exit with a simple return 0
signal/x86: In emulate_vsyscall force a signal instead of calling do_exit
signal/sparc32: In setup_rt_frame and setup_fram use force_fatal_sig
signal/sparc32: Exit with a fatal signal when try_to_clear_window_buffer fails
exit/syscall_user_dispatch: Send ordinary signals on failure
signal: Implement force_fatal_sig
exit/kthread: Have kernel threads return instead of calling do_exit
signal/s390: Use force_sigsegv in default_trap_handler
signal/vm86_32: Properly send SIGSEGV when the vm86 state cannot be saved.
signal/vm86_32: Replace open coded BUG_ON with an actual BUG_ON
signal/sparc: In setup_tsb_params convert open coded BUG into BUG
signal/powerpc: On swapcontext failure force SIGSEGV
signal/sh: Use force_sig(SIGKILL) instead of do_group_exit(SIGKILL)
signal/mips: Update (_save|_restore)_fp_context to fail with -EFAULT
signal/sparc32: Remove unreachable do_exit in do_sparc_fault
...
In 2009 Oleg reworked[1] the kernel threads so that it is not
necessary to call do_exit if you are not using kthread_stop(). Remove
the explicit calls of do_exit and complete_and_exit (with a NULL
completion) that were previously necessary.
[1] 63706172f3 ("kthreads: rework kthread_stop()")
Link: https://lkml.kernel.org/r/20211020174406.17889-12-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
netdev->dev_addr will be constant soon, make sure
the qualifier is propagated thru batman-adv.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check if a batman-adv related object is NULL or not is now directly in
the batadv_*_put functions. It is not needed anymore to perform this check
outside these function:
The changes were generated using a coccinelle semantic patch:
@@
expression E;
@@
- if (likely(E != NULL))
(
batadv_backbone_gw_put
|
batadv_claim_put
|
batadv_dat_entry_put
|
batadv_gw_node_put
|
batadv_hardif_neigh_put
|
batadv_hardif_put
|
batadv_nc_node_put
|
batadv_nc_path_put
|
batadv_neigh_ifinfo_put
|
batadv_neigh_node_put
|
batadv_orig_ifinfo_put
|
batadv_orig_node_put
|
batadv_orig_node_vlan_put
|
batadv_softif_vlan_put
|
batadv_tp_vars_put
|
batadv_tt_global_entry_put
|
batadv_tt_local_entry_put
|
batadv_tt_orig_list_entry_put
|
batadv_tt_req_node_put
|
batadv_tvlv_container_put
|
batadv_tvlv_handler_put
)(E);
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit b37a466837 ("netdevice: add the case if dev is NULL") changed
the way how the NULL check for net_devices have to be handled when trying
to reduce its reference counter. Before this commit, it was the
responsibility of the caller to check whether the object is NULL or not.
But it was changed to behave more like kfree. Now the callee has to handle
the NULL-case.
The batman-adv code was scanned via cocinelle for similar places. These
were changed to use the paradigm
@@
identifier E, T, R, C;
identifier put;
@@
void put(struct T *E)
{
+ if (!E)
+ return;
kref_put(&E->C, R);
}
Functions which were used in other sources files were moved to the header
to allow the compiler to inline the NULL check and the kref_put call.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
kernel-doc can only correctly identify the documented function or struct
when the name in the first kernel-doc line references it. But some of the
kernel-doc blocks referenced a different function/struct then it actually
documented.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv source code was using the year of publication (to net-next)
as "last" year for the copyright statement. The whole source code mentioned
in the MAINTAINERS "BATMAN ADVANCED" section was handled as a single entity
regarding the publishing year.
This avoided having outdated (in sense of year information - not copyright
holder) publishing information inside several files. But since the simple
"update copyright year" commit (without other changes) in the file was not
well received in the upstream kernel, the option to not have a copyright
year (for initial and last publication) in the files are chosen instead.
More detailed information about the years can still be retrieved from the
SCM system.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit b296a6d533 ("kernel.h: split out min()/max() et al. helpers")
moved the min/max helper functionality from kernel.h to minmax.h. Adjust
the kernel code accordingly to avoid fragile indirect includes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 54d50897d5 ("linux/kernel.h: split *_MAX and *_MIN macros into
<linux/limits.h>") moved the U32_MAX/INT_MAX/ULONG_MAX from linux/kernel.h
to linux/limits.h. Adjust the includes accordingly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All files got a SPDX-License-Identifier with commit 7db7d9f369
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
-----BEGIN PGP SIGNATURE-----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=5JUK
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20171220' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>