Class W can be used for any path where only data from the DAC is routed
to the headphones. Currently we only enable it when the direct DAC to
headphone path is used but it can also be enabled for paths that go via
the output mixer providing the DAC is the only input to the output mixer.
Implement support for this, including updates to the class W status when
the output mixer configuration is changed. This also allows us to enable
the DC servo optimisations for DAC to headphone paths where the output
mixer is used.
In general the direct DAC path is still preferred as this will offer
better performance on most wm_hubs devices but these additional paths
can simplify use case management.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the analogue portions of the checks for class W are the same over
all the devices factor out these checks into wm_hubs and while we're at
it also use wm_hubs_dac_hp_direct() to enable class W optimisations on
more paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimisations which we can do with caching the headphone DCS result in
wm_hubs have only been enabled in cases where class W is enabled. However,
there are more use cases which can benefit from the cache, especially with
WM8994 series devices with their more advanced digital routing.
Rather than keying off the class W information from the CODECs have a
check in wm_hubs for a suitable path and use that to determine if we can
deploy our headphone optimisations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added AT91SAM9N12 SoC DT file, as well as the board definition
.dts file for AT91SAM9N12-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Remove writable debugFS permission, use simple_open() and
fix indentation.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a bug discovered during testing of non pll slave mode.
Due to the bug chip was not getting correctly configured and as a result
there was no sound output while playback. After applying this patch,
both pll and non pll modes work fine.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reduce our stack consumption by moving the params off the stack, they
are reasonably large and might be an issue on platforms with small stacks.
Reported-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ackeded-by: Liam Girdwood <lrg@ti.com>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bug noticed in commit
bf118a342f
When calling GETACL, if the size of the bitmap array, the length
attribute and the acl returned by the server is greater than the
allocated buffer(args.acl_len), we can Oops with a General Protection
fault at _copy_from_pages() when we attempt to read past the pages
allocated.
This patch allocates an extra PAGE for the bitmap and checks to see that
the bitmap + attribute_length + ACLs don't exceed the buffer space
allocated to it.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reported-by: Jian Li <jiali@redhat.com>
[Trond: Fixed a size_t vs unsigned int printk() warning]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix kernel-doc warning in spi.h (copy/paste):
Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Epei
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
BIOS will switch off the corresponding feature flag on family
15h models 10h-1fh non-desktop CPUs.
The topology extension CPUID leafs are required to detect which
cores belong to the same compute unit. (thread siblings mask is
set accordingly and also correct information about L1i and L2
cache sharing depends on this).
W/o this patch we wouldn't see which cores belong to the same
compute unit and also cache sharing information for L1i and L2
would be incorrect on such systems.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code puts the built-in WMAC device of the
AR933X SoCs into reset instead of starting it. This
causes a hard lock on AR933X based boards when the
wireless driver tries to access the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3484/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the last fixes to this driver ensure now the queue termination is
done correctly, we can finally disable the queue after a transfer
without problems. The gain is that it will only be reenabled after the
next transfer is fully set up. Before, the queue was running all the
time and if the setup of the next message was interrupted by another
thread, an incomplete buffer could have been sent, padded with zeroes.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Adds check to ensure TIPC sockets reject incoming payload messages
that have an unrecognized message type.
Remove the old open question about whether TIPC_ERR_NO_PORT is
the proper return value. It is appropriate here since there are
valid instances where another node can make use of the reply,
and at this point in time the host is already broadcasting TIPC
data, so there are no real security concerns.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Everytime a HID device is opened, a new hiddev_list is allocated with
kzalloc. This requires 64KB of physically contiguous memory, which could
easily push a heavily loaded system over the edge.
Allocating the same amount of memory with vmalloc shouldn't be nearly as
demanding, so let's do that instead. The memory isn't used for DMA and
doesn't look particularly performance sensitive, so this should be safe.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All mainline platforms using the ARM architected timers are DT
only. As such, remove the ad-hoc support that is not longer needed
anymore.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If CONFIG_LOCAL_TIMERS is not defined, let the architected timer
driver register a single clock_event_device that is used as a
global timer.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add runtime DT support and documentation for the Cortex A7/A15
architected timers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide an A15 sched_clock implementation using the virtual counter,
which is thought to be more useful than the physical one in a
virtualised environment, as it can offset the time spent in another
VM or the hypervisor.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the A15 generic timer and clocksource.
As the timer generates interrupts on a different PPI depending
on the execution mode (normal or secure), it is possible to
register two different PPIs.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When running an SMP_ON_UP enabled kernel on UP, or with nosmp
passed to the kernel, we want to be able to detect that a local
timer is not going to be used (local timers are only used on
SMP platforms), so we could register it as a global timer instead.
Return -ENXIO when the above case is detected.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Let CONFIG_MACH_IMX27_DT be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch eliminates parameter "buf1" from function gfs2_setbit.
This is possible because it was always passed in as bi->bi_bh->b_data.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes:
WARNING: arch/arm/mach-davinci/built-in.o(.text+0x2d84): Section mismatch in reference from the function da850_evm_ui_expander_setup() to the (unknown reference) .init.data:(unknown)
The function da850_evm_ui_expander_setup() references
the (unknown reference) __initdata (unknown).
This is often because da850_evm_ui_expander_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Note this is a real issue because if the tca6416 driver only binds when
the init sections are already discarded da850_evm_ui_expander_setup is
called when da850_evm_devices might already be overwritten.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Direct keys usage may not start from KP_DKIN0, add a msk option
to configure the specifics for platforms that can skip some keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
KPDK_DK only indicates the pin level of direct key.
So it is related to board, and low level may be active which
indicates that a key is pressed.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When direcct_key_num is 0, the mask should be 0.
When direcct_key_num is 1, the mask should be 0b1.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When the keypad is used as wake up source, the clock can not
be disabled. Or it can not detect key pressing.
If the keypad is used as wake up source, when resume back,
do not enable the clock and configure it again because the
register content is retained.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This helper macro retrieves the fractional part of a fixed20_12 20.12
fixed-point number.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
