While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into gpio/next
Linux 3.3-rc7. Merged into the gpio branch to pick up gpio bugfixes already
in mainline before queueing up move v3.4 patches
Stylus buttons have to be resetted when going out-of-prox.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
num_sifr could go negative since acpi_pcc_get_sqty() returns -EINVAL
on error. Then it could bypass the sanity check (num_sifr > 255).
The subsequent call to kzalloc() would allocate a small buffer, leading
to a memory corruption.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add an ethernet SPI chip in the OMAP4 SDP/Blaze board DTS file.
Add a fixed regulator node controlled by a GPIO line to supply
the ethernet chip.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add the 4 McSPI controller nodes present in an OMAP3 device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add the 4 McSPI controller nodes present in an OMAP4 device.
Remove SPI static device initialisation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
We have several reports which says acer-wmi is loaded on ideapads
and register rfkill for wifi which can not be unblocked.
Since ideapad-laptop also register rfkill for wifi and it works
reliably, it will be fine acer-wmi is not going to register rfkill
for wifi once VPC2004 is found.
Also put IBM0068/LEN0068 in the list. Though thinkpad_acpi has no
wifi rfkill capability, there are reports which says acer-wmi also
block wireless on Thinkpad E520/E420.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch adds support for some of the devices within a wide variety
of Fujitsu Tablet Computers, both convertibles and slates. Primarily
it allows for the automatic detection of the tablet/notebook mode for
convertible tablet pc's, and orientation for docked slates. It also
adds support for the application panel buttons usually found next to
the tablet screen, and docking station detection for slates.
Signed-off-by: Robert Gerlach <khnz@gmx.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This mainly reverts the commit that was adding the i2c static init.
Since the i2c and twl nodes are now present, there is no need
for the static initialization anymore.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
An rfkill driver based on the fsaa1655g and fsam7440 drivers for
Fujitsu-Siemens Amilo A1655 and M7440 models found at:
http://sourceforge.net/projects/fsaa1655g/http://sourceforge.net/projects/fsam7440/
This adds DMI matching, replaces the procfs files with rfkill devices,
and uses the proper functions to write to the i8042 safely.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Added the vmaster hook for controlling EAPD dynamically to Conexant
auto-parser. When the Master is muted, EAPDs are turned off as well.
This will fix the missing mute-LED control on some machines in
addition to the more power-saving in the auto-parser mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've had ugly static handling of the mute-LED with a powersave hook
for ALC269 HP laptops just like done in patch_sigmatel.c. This is now
rewritten with the new vmaster hook and a fixup code.
For that, the new fixup action, ALC_FIXUP_ACT_BUILD, is introduced.
It's called after build_controls is called. The reason of this new
action is that vmaster hook must be added at this stage (not in init
or probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED is controlled in patch_sigmatel.c by (ab-)using the
powersave hook. This can be now rewritten with the vmaster hook
instead, which is much simpler and can work even without
CONFIG_SND_HDA_POWER_SAVE kconfig.
A drawback is that the mute-LED corresponds _only_ to the Master mixer
switch instead of checking the whole DACs. But usually this shouldn't
be a big problem as PA enables the mixer elements accordingly.
Also, this patch changes the code to create vmaster always even on
STAC9200 and STAC925x. The former "Master" on these chips are renamed
as "PCM" now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The McBSP driver stack has been moved, and rewritten resulting a single
driver - selected by CONFIG_SND_OMAP_SOC_MCBSP. There is no longer need to
have CONFIG_OMAP_MCBSP anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The McBSP driver stack has been moved to ASoC. The CONFIG_OMAP_MCBSP will
be removed since the CONFIG_SND_OMAP_SOC_MCBSP will trigger to build the
McBSP (audio) drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
We are setting SNDRV_PCM_HW_PARAM_BUFFER_SIZE based on
SNDRV_PCM_HW_PARAM_CHANNELS, not vice versa. This bug didn't
have much impact because the rules are evaluated multiple times
by the core, and intended value got set eventually.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Remove the no longer valid check for McBSP1 regarding to signal mux
selection (on OMAP4 McBSP4 has 6 pin setup).
Only clear the srgr2, pcr0 register configuration if the requested clock
configuration will actually going to touch it. In this way we can avoid
issues if the CLKR/FSR mux has been configured after the clock selection.
We are going to check for the valid McBSP port in the
omap_mcbsp_6pin_src_mux() function based on the validity of the mux_signal
callback (which is only valid for ports having 6 pin setup).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use single function for the CLKR/FSR mux configuration.
OMAP2/3 has 6 pin configuration on McBSP1 instance, while on OMAP4
McBSP4 instance have the 6 pin configuration so the omap2_mcbsp1_mux_* is
not correct name for all support OMAP versions
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Clock signal muxing, and functional clock related defines are only needed
in ASoC drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP2/3 McBSP1 port has 6 pin setup, while on OMAP4 the port is McBSP4.
Implement the CLKR/FSR clock mux selection for OMAP4, and make sure that
we add the correct callback for the correct port across supported OMAP
versions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP4 we have one interrupt line per McBSP port.
At probe time tx, and rx irq value will be -ENXIO,
and only the tx irq will get corrected.
In omap_mcbsp_request if the rx_irq is not 0 we proceed,
and try to request the interrupt, which will fail on
OMAP4 (rx_irq == -6).
To avoid this error, clear the rx_irq at probe time
on OMAP4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
If external source for the CLKS signal selection kept after the port is no
longer in use the system might refuse to go suspend.
There is also a chance that the external clock is not running when next
time the McBSP port is started which can result errors when we try to
access McBSP registers.
Reset the CLKS source back to PRCM source unconditionally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Configure the WAKEUPEN register at the same time we configure the rest of
the McBSP registers.
In case of OMAP3+, if the sysclock has been reconfigured we are going to
disable McBSP for the duration of the clock change, which will reset the
McBSP registers. The WAKEUPEN register need to be configured later, so
the changes will be effective during runtime.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicrocom>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The parent functions of omap_st_start/stop also checks the validity of the
st_data pointer so we do not need to do it again inside of omap_st_start/stop
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In this way we can save few lines, and have uniform way of initializing the
st_data in all functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Configure the DMA request line, port address, and stream name at
probe time instead of every time we start a stream.
These settings are static in the system.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Since the drivers has been merged, merge the two structures together.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use devm_* where it is possible to save on cleanup path.
Start merging the two mcbsp file content.
Move pm_runtime_enable/disable calls to ASoC probe, remove from module
probe/remove time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
We no longer need accessor functions for max_tx/rx_threshold, dma_op_mode
or for the FIFO size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use BIT() for bit position, correct field definition by adding mask to
them, and also adding the missing spaces around '<<'
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The driver for omap-mcbsp-dai no longer exist since it has been merged with
the omap-mcbsp driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).
Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.
Further cleanup is coming...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to consolidate the McBSP driver move it out from
arch/arm/plat-omap directory under sound/soc/omap/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Convert the plat-omap/mcbsp.c driver to be proper platform driver.
Remove the omap_mcbsp_init function call which was called from
mach-omap1/2/mcbsp.c to register the platform driver for the just
created platform device in the same function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The cpu_is_omap4430() macro always return with 0. Use the correct
cpu_is_omap443x() to check for Panda revision.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
This patch adds a hook to vmaster control to be called at each time
when the master value is changed. It'd be handy for an additional
mute LED control following the Master switch, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Microsoft's documentation about multitouch protocols tells that
if a device presents one touch per report, then it should be treated
as a serial protocol.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most callback functions implementation for tps65217_pmic_ldo234_ops and
tps65217_pmic_dcdc_ops are the same except the rid range checking.
This patch uses tps65217_pmic_ops for all DCDCx, LDO2, LDO3, and LDO4.
And rework tps65217_pmic_set_voltage to make it can be called for
DCDCx, LDO2, LDO3, and LDO4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DIV_ROUND_CLOSEST performs the computation (x + d/2)/d with better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The widget locking depends on some of the other locking changes which
are queued up for 3.5 not 3.4 so revert the locking changes and reapply
them in 3.5.
This reverts commit 66bf93212f and
96acc357be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Previous code used wrong instance for the interrupt register access.
Use the right one which is OCP_SOCKET.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is useful when we have broken type2 compliant IPs' where
the softreset shift is not the same as SYSC_TYPE2_SOFTRESET_SHIFT
and hence is overridden using sysc_fields->srst_shift.
We have at least one such instance now with onchip keypad on OMAP5
which has a different softreset shift as compared to other type2
IPs'.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Balaji TK <balajitk@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When the quirk HID_QUIRK_MULTITOUCH is present and when hid-multitouch
is loaded, let's pass the device to hid-multitouch even if it has
not been registered in hid-multitouch.
If any other driver wants to take precedence over hid-multitouch,
the usual way of adding it to hid_have_special_driver will work as
the quirk HID_QUIRK_MULTITOUCH won't be set by the generic hid layer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LG multitouch panels, such as the one found in Dell ST2220T, has buggy
reports descriptors. With the previous implementation, it was impossible
to rely on the reports descriptors to determine how the different
touches are emitted from the device.
This patch changes the splitting of the different touches in the report
in a more robust way.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>