Zero out the buffer for readlink() since readlink() does not append a
terminating null byte to the buffer. Also change the buffer length
passed to readlink() to 'PATH_MAX - 1' to ensure the resulting string
is always null terminated.
Fixes: 833c12ce0f ("selftests/x86/lam: Add inherit test cases for linear-address masking")
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20231016062446.695-1-binbin.wu@linux.intel.com
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI
bridge helpers and implementing i.MX93 MIPI DSI specific extensions.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-10-victor.liu@nxp.com
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-9-victor.liu@nxp.com
According to Synopsys DW MIPI DSI host databook, HSTX and LPRX timeout
contention detections are measured in TO_CLK_DIVISION cycles. However,
the current driver programs magic values to TO_CLK_DIVISION, HSTX_TO_CNT
and LPRX_TO_CNT register fields, which makes timeout error event wrongly
happen for some video modes, at least for the typical 1920x1080p@60 video
mode read from a HDMI monitor driven by ADV7535 DSI to HDMI bridge.
While at it, the current driver doesn't enable interrupt to handle or
complain about the error status, so true error just happens silently
except for display distortions by visual check.
Disable the timeout check by setting those timeout register fields to
zero for now until someone comes along with better computations for the
timeout values. Although the databook doesn't mention what happens when
they are set to zero, it turns out the false error doesn't happen for
the 1920x1080p@60 video mode at least.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-8-victor.liu@nxp.com
According to Synopsys support channel, each region of HSA, HBP and HFP must
have minimum number of 10 bytes where constant 4 bytes are for HSS or HSE
and 6 bytes are for blanking packet(header + CRC). Hence, the below table
comes in.
+------------+----------+-------+
| data lanes | min lbcc | bytes |
+------------+----------+-------+
| 1 | 10 | 1*10 |
+------------+----------+-------+
| 2 | 5 | 2*5 |
+------------+----------+-------+
| 3 | 4 | 3*4 |
+------------+----------+-------+
| 4 | 3 | 4*3 |
+------------+----------+-------+
Implement the minimum lbcc numbers to make sure that the values programmed
into DSI_VID_HSA_TIME and DSI_VID_HBP_TIME registers meet the minimum
number requirement. For DSI_VID_HLINE_TIME register, it seems that the
value programmed should be based on mode->htotal as-is, instead of sum up
HSA, HBP, HFP and HDISPLAY.
This helps the case where Raydium RM67191 DSI panel is connected, since
it's video timing for hsync length is only 2 pixels and without this patch
the programmed value for DSI_VID_HSA_TIME is only 2 with 4 data lanes.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-7-victor.liu@nxp.com
To get better accuration, use pixel clock rate to calculate lbcc instead of
lane_mbps since the pixel clock rate is in KHz while lane_mbps is in MHz.
Without this, distorted image can be seen on a HDMI monitor connected with
i.MX93 11x11 EVK through ADV7535 DSI to HDMI bridge in 1920x1080p@60 video
mode.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-6-victor.liu@nxp.com
Vendor drivers may need to fixup mode due to pixel clock tree limitation,
so introduce the ->mode_fixup() callcack to struct dw_mipi_dsi_plat_data
and call it at atomic check stage if available.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-5-victor.liu@nxp.com
The DATAEN_ACTIVE_LOW bit in DSI_DPI_CFG_POL register is set to zero,
so set the DRM_BUS_FLAG_DE_HIGH flag in input_bus_cfg.flags. It appears
that the DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE flag also makes sense, so
set it in input_bus_cfg.flags too. With this patch, the flags set by
drm_atomic_bridge_propagate_bus_flags() are overridden (see comment in
that function) in case any downstream bridges propagates invalid flags
to this bridge. A real problematic case is to connect a RM67191 MIPI
DSI panel whose driver sets DRM_BUS_FLAG_DE_LOW and
DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE bus flags.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-4-victor.liu@nxp.com
Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data
so that vendor drivers can implement specific methods to get input bus
formats for Synopsys DW MIPI DSI.
While at it, implement a generic callback for ->atomic_get_input_bus_fmts(),
where we try to get the input bus formats through pdata->get_input_bus_fmts()
first. If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED,
which matches the default behavior if ->atomic_get_input_bus_fmts() is not
implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-3-victor.liu@nxp.com
Add dw_mipi_dsi_get_bridge() helper so that it can be used by vendor
drivers which implement vendor specific extensions to Synopsys DW MIPI DSI.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-2-victor.liu@nxp.com
Fixes: 8bd2f71054 ("virtio_ring: introduce dma sync api for virtqueue")
also add dma sync api for virtio test.
Signed-off-by: Liming Wu <liming.wu@jaguarmicro.com>
Message-Id: <20231008031734.1095-1-liming.wu@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The of_gpio.h is not and shouldn't be used in the drivers. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for W25N01JW, W25N02JWZEIF, W25N512GW,
W25N02KWZEIR and W25N01GWZEIG.
W25N02KWZEIR has 8b/512b on-die ECC capability and other
four has 4b/512b on-die ECC capability.
Signed-off-by: Sridharan S N <quic_sridsn@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231012064134.4068621-1-quic_sridsn@quicinc.com
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cdns_nand_chip.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Valentin Korenblit <vkorenblit@sequans.com>
Cc: ye xingchen <ye.xingchen@zte.com.cn>
Cc: linux-mtd@lists.infradead.org
Cc: linux-hardening@vger.kernel.org
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231006201734.work.060-kees@kernel.org
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct
mtk_nfc_nand_chip.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Cai Huoqing <cai.huoqing@linux.dev>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Li Zetao <lizetao1@huawei.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-hardening@vger.kernel.org
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231006201728.work.750-kees@kernel.org
Use struct_size() instead of hand writing it.
This is less verbose and more robust.
While at it, prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with __counted_by
can have their accesses bounds-checked at run-time checking via
CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for
strcpy/memcpy-family functions).
Also remove a useless comment about the position of a flex-array in a
structure.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/481721c2c7fe570b4027dbe231d523961c953d5a.1696146232.git.christophe.jaillet@wanadoo.fr
Following an ECC failure condition upon page reads, we shall distinguish
between a real ECC failure and an empty page. This is handled with a call
to nand_check_erased_ecc_chunk() which looks at the data and counts the
number of bits which are not 'ones'. If we get less zeros than the ECC
strength, we assume the page was erased and we are in the presence of
natural bitflips. Otherwise, if we are above, we assume some data was
written and the ECC engine could not recover it all, so we report an ECC
failure.
In order for this logic to be as close as the reality as we can (this is
already a simplified condition but we can hardly be more precise), we
should check all the data that is covered by the ECC step not only the
in-band data, so we should also include the ECC syndrome in the check.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230927055621.2906454-1-amit.kumar-mahapatra@amd.com
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231009172923.2457844-1-robh@kernel.org
As per spec, it is allowed to pulse the HPD signal to indicate that the
EDID information has changed. Some monitors do this when they wake up
from standby or are enabled. When the HPD goes low the adv7511 is
reset and the outputs are disabled which might cause the monitor to
go to standby again. To avoid this we ignore the HPD pin for the
first few seconds after enabling the output. On the other hand,
adv7535 require to enable HPD Override bit for proper HPD.
Add hpd_override_enable variable to struct adv7511_chip_info to handle
this scenario.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-9-biju.das.jz@bp.renesas.com
The ADV7511 needs link configuration whereas ADV75{33,35} does not need
it. Add a variable link_config to struct adv7511_chip_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-8-biju.das.jz@bp.renesas.com
The ADV7533 and ADV7535 have an offset(0x70) for the CEC register map
compared to ADV7511. Add the reg_cec_offset variable to struct
adv7511_chip_info to handle this difference and drop the reg_cec_offset
variable from struct adv7511.
This will avoid assigning reg_cec_offset based on chip type and also
testing for multiple chip types by calling adv7533_patch_cec_registers().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-6-biju.das.jz@bp.renesas.com
The ADV7511 has 5 power supplies compared to 7 that of ADV75{33,35}. Add
supply_names and num_supplies variables to struct adv7511_chip_info to
handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-5-biju.das.jz@bp.renesas.com
The ADV7533 supports a maximum lane clock of 800MHz whereas it is 891MHz
for ADV7535. Add max_lane_freq_khz variable to struct adv7511_chip_info to
handle this difference.
While at it, drop the unused local variable max_lane_freq.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-4-biju.das.jz@bp.renesas.com
The ADV7533 supports a maximum pixel clock of 80MHz whereas it is 148.5MHz
for ADV7535. Add max_mode_clock_khz variable to struct adv7511_chip_info to
handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-3-biju.das.jz@bp.renesas.com
Add struct adv7511_chip_info to handle hw differences between various
chips rather checking against the 'type' variable in various places.
Replace 'adv->type'->'info->type' by moving variable 'type' from
struct adv7511 to struct adv7511_chip_info and add adv7511_chip_info as
device data for both OF and ID tables instead of the device type.
Simplify the probe() by replacing of_device_get_match_data() and ID lookup
for retrieving match data with i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-2-biju.das.jz@bp.renesas.com
The tsnep network controller is able to extend the descriptor directly
with data to be transmitted. In this case no TX data DMA address is
necessary. Instead of the TX data DMA address the TX data buffer is
placed at the end of the descriptor.
The descriptor is read with a 64 bytes DMA read by the tsnep network
controller. If the sum of descriptor data and TX data is less than or
equal to 64 bytes, then no additional DMA read is necessary to read the
TX data. Therefore, it makes sense to inline small fragments up to this
limit within the descriptor ring.
Inlined fragments need to be copied to the descriptor ring. On the other
hand DMA mapping is not necessary. At most 40 bytes are copied, so
copying should be faster than DMA mapping.
For A53 1.2 GHz copying takes <100ns and DMA mapping takes >200ns. So
inlining small fragments should result in lower CPU load. Performance
improvement is small. Thus, comparision of CPU load with and without
inlining of small fragments did not show any significant difference.
With this optimization less DMA reads will be done, which decreases the
load of the interconnect.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani says:
====================
net: consolidate IPv4 route lookup for UDP tunnels
At the moment different UDP tunnels rely on different functions for
IPv4 route lookup, and those functions all implement the same
logic. Only bareudp uses the generic ip_route_output_tunnel(), while
geneve and vxlan basically duplicate it slightly differently.
This series first extends the generic lookup function so that it is
suitable for all UDP tunnel implementations. Then, bareudp, geneve and
vxlan are adapted to use them.
This results in code with less duplication and hopefully better
maintainability.
After this series is merged, IPv6 will be converted in a similar way.
Changelog:
v2
- fix compilation with IPv6 disabled
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The route lookup can be done now via generic function
udp_tunnel_dst_lookup() to replace the custom implementations in
vxlan_get_route().
Note that this patch only touches IPv4, while IPv6 still uses
vxlan6_get_route(). After IPv6 route lookup gets converted as well,
vxlan_xmit_one() can be simplified by removing local variables that
will be passed via "struct ip_tunnel_key", such as remote_ip,
local_ip, flow_flags, label.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route lookup can be done now via generic function
udp_tunnel_dst_lookup() to replace the custom implementation in
geneve_get_v4_rt().
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to compute the tos/dsfield. In this way, we can
factor out some duplicate code. Also, the helper will be called from
more places in the next commit.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 451ef36bd2 ("ip_tunnels: Add new flow flags field to
ip_tunnel_key") added a new field to struct ip_tunnel_key to control
route lookups. Currently the flag is used by vxlan and geneve tunnels;
use it also in udp_tunnel_dst_lookup() so that it affects all tunnel
types relying on this function.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to make the function more generic so that it can be used by
other UDP tunnel implementations such as geneve and vxlan. To do that,
add the following arguments:
- source and destination UDP port;
- ifindex of the output interface, needed by vxlan;
- the tos, because in some cases it is not taken from struct
ip_tunnel_info (for example, when it's inherited from the inner
packet);
- the dst cache, because not all tunnel types (e.g. vxlan) want to
use the one from struct ip_tunnel_info.
With these parameters, the function no longer needs the full struct
ip_tunnel_info as argument and we can pass only the relevant part of
it (struct ip_tunnel_key).
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is now UDP-specific, the protocol is always IPPROTO_UDP.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment ip_route_output_tunnel() is used only by bareudp.
Ideally, other UDP tunnel implementations should use it, but to do so
the function needs to accept new parameters that are specific for UDP
tunnels, such as the ports.
Prepare for these changes by renaming the function to
udp_tunnel_dst_lookup() and move it to file
net/ipv4/udp_tunnel_core.c.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-21-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-20-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-18-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-17-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-16-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-15-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-14-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-13-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-12-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-11-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-10-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-9-u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20231008200143.196369-8-u.kleine-koenig@pengutronix.de
