The ad2s1210 driver has a device-specific attribute `fexcit` for setting
the frequency of the excitation output. This converts it to a channel in
order to use standard IIO ABI.
The excitation frequency is an analog output that generates a sine wave.
Only the frequency is configurable. According to the datasheet, the
specified range of the excitation frequency is from 2 kHz to 20 kHz and
can be set in increments of 250 Hz.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-3-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD2S1210 resolver has a hysteresis feature that can be used to
prevent flicker in the LSB of the position register. This can be either
enabled or disabled. Disabling hysteresis is useful for increasing
precision by oversampling.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-2-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When reading registers on the AD2S1210 chip, we have to supply a "dummy"
address for the second SPI tx byte so that we don't accidentally write
to a register. This register will be read and the value discarded on the
next regmap read or write call.
Reading the fault register has a side-effect of clearing the faults
so we should not use this register for the dummy read.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-1-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
simplified the driver with devm hooks, but wrongly states that the
platform_set_drvdata(), platform_get_drvdata() are unused after the
simplification: the driver data is infact used in .suspend() and
.resume() PM callbacks, currently producing a kernel panic.
Reintroduce the call to platform_set_drvdata() in the probe function
Fixes: a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231010121940.159696-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add fast settling mode support for AD7193.
Add two new device specific attributes: oversampling_ratio and
oversampling_ratio_available.
For AD7193 the user can set the average factor by writing to
oversampling_ratio. The possible values are exposed when reading
oversampling_ratio_available.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20231010124927.143343-4-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reverted as Rob Herring is tracking undocumented compatibles and as per
discussion in the thread, we can not remove this deprecated compatibles from
the driver without potential/likely regressions. So keep it around
as it's not that painful anyway.
This reverts commit 711fb79a1e.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When either reset- or shutdown-gpio have are initially deasserted,
e.g. after a reboot - or when the hardware does not include pull-down,
there will be a short toggle of both IOs to logical 0 and back to 1.
It seems that the rfkill default is unblocked, so the driver should not
glitch to output low during probe.
It can lead e.g. to unexpected lte modem reconnect:
[1] root@localhost:~# dmesg | grep "usb 2-1"
[ 2.136124] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 21.215278] usb 2-1: USB disconnect, device number 2
[ 28.833977] usb 2-1: new SuperSpeed USB device number 3 using xhci-hcd
The glitch has been discovered on an arm64 board, now that device-tree
support for the rfkill-gpio driver has finally appeared :).
Change the flags for devm_gpiod_get_optional from GPIOD_OUT_LOW to
GPIOD_ASIS to avoid any glitches.
The rfkill driver will set the intended value during rfkill_sync_work.
Fixes: 7176ba23f8 ("net: rfkill: add generic gpio rfkill driver")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20231004163928.14609-1-josua@solid-run.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the previous key leak fix for the other error
paths, I meant to unify all of them to the same
place, but used the wrong label, which I noticed
when doing the merge into wireless-next. Fix it.
Fixes: d097ae01eb ("wifi: mac80211: fix potential key leak")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since wiphy work items can run pretty much arbitrary
code in the stack/driver, it can take longer to run
all of this, so we shouldn't be using system_wq via
schedule_work(). Also, we lock the wiphy (which is
the reason this exists), so use system_unbound_wq.
Reported-and-tested-by: Kalle Valo <kvalo@kernel.org>
Fixes: a3ee4dc84c ("wifi: cfg80211: add a work abstraction with special semantics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When transmitting, infrared drivers expect an odd number of samples; iow
without a trailing space. No problems have been observed so far, so
this is just belt and braces.
Fixes: 9b6192589b ("media: lirc: implement scancode sending")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This fixes two smatch warnings:
drivers/staging/media/atomisp/pci/atomisp_cmd.c:2779 atomisp_cp_dvs_6axis_config() warn: missing unwind goto?
drivers/staging/media/atomisp/pci/atomisp_cmd.c:2878 atomisp_cp_morph_table() warn: missing unwind goto?
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CC: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Check if the format was really found.
Fixes smatch warning:
drivers/media/i2c/tc358746.c:790 tc358746_set_fmt() error: 'fmt' dereferencing possible ERR_PTR()
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CC: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Also fixes a smatch warning:
drivers/staging/media/atomisp/i2c/atomisp-gc0310.c:446 gc0310_s_stream() warn: missing error code 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CC: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The dev->id value comes from ida_alloc() so it's a number between zero
and INT_MAX. If it's too high then these sprintf()s will overflow.
Fixes: 203d3d4aa4 ("the generic thermal sysfs driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Become designated reviewer and help thermal subsystem in development
process.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Amit Kucheria has not been participating in kernel development in any
way or form for quite some time, so it is not useful to list him as a
designated reviewer for the thermal subsystem or as the thermal zone DT
binding maintainer.
Remove him from the THERMAL entry in MAINTAINERS and list Daniel Lezcano
as the new thermal zone DT binding maintainer.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Amit Kucheria <amitk@kernel.org>
There is a typo so this checks the wrong variable. "chains" plural vs
"chain" singular. We already know that "chains" is non-zero.
Fixes: 7f993623e9 ("locktorture: Add call_rcu_chains module parameter")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
The Linux NFS server strips the SUID and SGID from the file mode
on ALLOCATE op.
Modify _nfs42_proc_fallocate to add NFS_INO_REVAL_FORCED to
nfs_set_cache_invalid's argument to force update of the file
mode suid/sgid bit.
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This makes the driver work with the new check in
v4l2_async_register_subdev() that was introduced recently in 6.6-rc1.
Without this change, probe fails with:
ov8858 1-0036: Detected OV8858 sensor, revision 0xb2
ov8858 1-0036: sub-device fwnode is an endpoint!
ov8858 1-0036: v4l2 async register subdev failed
ov8858: probe of 1-0036 failed with error -22
This also simplifies the driver a bit.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In ipu_bridge_get_ivsc_acpi_dev(), the "ivsc_adev" acpi_device pointer
from the outer loop is handed over to the caller, which takes proper
care of its reference count.
However, the "consumer" acpi_device pointer from the inner loop is lost,
without decrementing its reference count.
Fix this by adding the missing call to acpi_dev_put().
Fixes: c66821f381 ("media: pci: intel: Add IVSC support for IPU bridge driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The big V4L2 async framework overhaul simplified linked lists used by the
V4L2 async framework. This affected a few drivers and it turns out a few
of those drivers rely on searching for entities in both async notifier's
waiting and done lists. Do that by separately traversing both.
Fixes: 9bf19fbf0c ("media: v4l: async: Rework internal lists")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit b035f5a6d8 ("mm: slab: reduce the kmalloc() minimum alignment
if DMA bouncing possible") allows architectures with non-coherent DMA to
define a small ARCH_KMALLOC_MINALIGN (e.g. sizeof(unsigned long long))
and this has been enabled on arm64. With KASAN_HW_TAGS enabled, however,
ARCH_SLAB_MINALIGN becomes 16 on arm64 (arch_slab_minalign() dynamically
selects it since commit d949a8155d ("mm: make minimum slab alignment a
runtime property")). This can lead to a situation where kmalloc-8 caches
are attempted to be created with a kmem_caches.size aligned to 16. When
the cache is mergeable, it can lead to kernel warnings like:
sysfs: cannot create duplicate filename '/kernel/slab/:d-0000016'
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.0-rc1-00001-gda98843cd306-dirty #5
Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
Call trace:
dump_backtrace+0x90/0xe8
show_stack+0x18/0x24
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x24
sysfs_warn_dup+0x64/0x80
sysfs_create_dir_ns+0xe8/0x108
kobject_add_internal+0x98/0x264
kobject_init_and_add+0x8c/0xd8
sysfs_slab_add+0x12c/0x248
slab_sysfs_init+0x98/0x14c
do_one_initcall+0x6c/0x1b0
kernel_init_freeable+0x1c0/0x288
kernel_init+0x24/0x1e0
ret_from_fork+0x10/0x20
kobject: kobject_add_internal failed for :d-0000016 with -EEXIST, don't try to register things with the same name in the same directory.
SLUB: Unable to add boot slab dma-kmalloc-8 to sysfs
Limit the __kmalloc_minalign() return value (used to create the
kmalloc-* caches) to arch_slab_minalign() so that kmalloc-8 caches are
skipped when KASAN_HW_TAGS is enabled (both config and runtime).
Reported-by: Mark Rutland <mark.rutland@arm.com>
Fixes: b035f5a6d8 ("mm: slab: reduce the kmalloc() minimum alignment if DMA bouncing possible")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: stable@vger.kernel.org # 6.5.x
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Since the stream API is still experimental it is currently locked away
behind the internal, default disabled, v4l2_subdev_enable_streams_api flag.
Advertising V4L2_SUBDEV_CAP_STREAMS when the streams API is disabled
confuses userspace. E.g. it causes the following libcamera error:
ERROR SimplePipeline simple.cpp:1497 Failed to reset routes for
/dev/v4l-subdev1: Inappropriate ioctl for device
Don't report V4L2_SUBDEV_CAP_STREAMS when the streams API is disabled
to avoid problems like this.
Reported-by: Dennis Bonke <admin@dennisbonke.com>
Fixes: 9a6b5bf4c1 ("media: add V4L2_SUBDEV_CAP_STREAMS")
Cc: stable@vger.kernel.org # for >= 6.3
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Provide common prototypes for arch_register_cpu() and
arch_unregister_cpu(). These are called by acpi_processor.c, with weak
versions, so the prototype for this is already set. It is generally not
necessary for function prototypes to be conditional on preprocessor macros.
Some architectures (e.g. Loongarch) are missing the prototype for this, and
rather than add it to Loongarch's asm/cpu.h, do the job once for everyone.
Since this covers everyone, remove the now unnecessary prototypes in
asm/cpu.h, and therefore remove the 'static' from one of ia64's
arch_register_cpu() definitions.
[ tglx: Bring back the ia64 part and remove the ACPI prototypes ]
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/E1qkoRr-0088Q8-Da@rmk-PC.armlinux.org.uk
pr_flush() does not guarantee that all messages would really get flushed
to the console. The best it could do is to wait with a given timeout.[*]
The current interval 100ms for checking the progress might seem too
long in some situations. For example, such delays are not appreciated
during suspend and resume especially when the consoles have been flushed
"long" time before the check.
On the other hand, the sleeping wait might be useful in other situations.
Especially, it would allow flushing the messages using printk kthreads
on the same CPU[*].
Use msleep(1) as a compromise.
Also measure the time using jiffies. msleep() does not guarantee
precise wakeup after the given delay. It might be much longer,
especially for times < 20s. See Documentation/timers/timers-howto.rst
for more details.
Note that msecs_to_jiffies() already translates a negative value into
an infinite timeout.
[*] console_unlock() does not guarantee flushing the consoles since
the commit dbdda842fe ("printk: Add console owner and waiter
logic to load balance console writes").
It would be possible to guarantee it another way. For example,
the spinning might be enabled only when the console_lock has been
taken via console_trylock().
But the load balancing is helpful. And more importantly, the flush
with a timeout has been added as a preparation step for introducing
printk kthreads.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20231006082151.6969-3-pmladek@suse.com
Turns out that we were relying on the globally installed headers, not
the ones we freshly compiled.
Add a manual include in CFLAGS to sort this out.
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # Build
Tested-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230825-wip-selftests-v3-3-639963c54109@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
"make headers" is a requirement before calling make on the selftests
dir, so we should not have to manually install those headers
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # Build
Tested-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230825-wip-selftests-v3-2-639963c54109@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
For the hid-bpf tests to compile, we need to have the definition of
struct hid_bpf_ctx. This definition is an internal one from the kernel
and it is supposed to be defined in the generated vmlinux.h.
This vmlinux.h header is generated based on the currently running kernel
or if the kernel was already compiled in the tree. If you just compile
the selftests without compiling the kernel beforehand and you are running
on a 6.2 kernel, you'll end up with a vmlinux.h without the hid_bpf_ctx
definition.
Use the clever trick from tools/testing/selftests/bpf/progs/bpf_iter.h
to force the definition of that symbol in case we don't find it in the
BTF and also add __attribute__((preserve_access_index)) to further
support CO-RE functionality for these tests.
Signed-off-by: Justin Stitt <justinstitt@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # Build
Tested-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230825-wip-selftests-v3-1-639963c54109@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Update the number of scalers per pipe based on the display
capabilities reported.
v1: define the field values instead of the magic number (JaniN)
Bspec: 71161
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001113155.80659-4-vinod.govindapillai@intel.com
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Update the global dsc flag based on the display capabilities
reported.
v1: define the field values instead of the magic number (JaniN)
Bspec: 71161
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001113155.80659-3-vinod.govindapillai@intel.com
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
In some implementations, such as the Qualcomm platforms, the display
driver has no way to query the current HPD state and as such it's
impossible to distinguish between disconnect and attention events.
Add a parameter to drm_connector_oob_hotplug_event() to pass the HPD
state.
Also push the test for unchanged state in the displayport altmode driver
into the i915 driver, to allow other drivers to act upon each update.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009174048.2695981-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009174048.2695981-2-dmitry.baryshkov@linaro.org
The timer capability to wakeup the cpu irrespective of its idle state is
provided by the flag in RHCT. Update the timer code to set this flag.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230927170015.295232-5-sunilvl@ventanamicro.com
There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq()
or platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
./drivers/clocksource/timer-sun5i.c:260:2-9: line 260 is redundant because platform_get_irq() already prints an error
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230831041414.66434-1-yang.lee@linux.alibaba.com
Add a wrapper around intel_step_name that takes in driver data as an
argument. This wrapper will help maintain compatibility with the
proposed xe driver.
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231003065211.1052385-1-chaitanya.kumar.borah@intel.com
On some OEM systems, adding a W7900 dGPU triggers RAS errors and hangs
at a black screen on startup. This issue occurs only if `ucsi_acpi` has
loaded before `amdgpu` has loaded. The reason for this failure is that
`amdgpu` uses power_supply_is_system_supplied() to determine if running
on AC or DC power at startup. If this value is reported incorrectly the
dGPU will also be programmed incorrectly and trigger errors.
power_supply_is_system_supplied() reports the wrong value because UCSI
power supplies provided as part of the system don't properly report the
scope as "DEVICE" scope (not powering the system).
In order to fix this issue check the capabilities reported from the UCSI
power supply to ensure that it supports charging a battery and that it can
be powered by AC. Mark the scope accordingly.
Cc: stable@vger.kernel.org
Fixes: a7fbfd44c0 ("usb: typec: ucsi: Mark dGPUs as DEVICE scope")
Link: https://www.intel.com/content/www/us/en/products/docs/io/universal-serial-bus/usb-type-c-ucsi-spec.html p28
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009184643.129986-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Willem de Bruijn says:
====================
add skb_segment kunit coverage
As discussed at netconf last week. Some kernel code is exercised in
many different ways. skb_segment is a prime example. This ~350 line
function has 49 different patches in git blame with 28 different
authors.
When making a change, e.g., to fix a bug in one specific use case,
it is hard to establish through analysis alone that the change does
not break the many other paths through the code. It is impractical to
exercise all code paths through regression testing from userspace.
Add the minimal infrastructure needed to add KUnit tests to networking,
and add code coverage for this function.
Patch 1 adds the infra and the first simple test case: a linear skb
Patch 2 adds variants with frags[]
Patch 3 adds variants with frag_list skbs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the test with these variants that use skb frag_list:
- GSO_TEST_FRAG_LIST: frag_skb length is gso_size
- GSO_TEST_FRAG_LIST_PURE: same, data exclusively in frag skbs
- GSO_TEST_FRAG_LIST_NON_UNIFORM: frag_skb length may vary
- GSO_TEST_GSO_BY_FRAGS: frag_skb length defines gso_size,
i.e., segs may have varying sizes.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the test with variants
- GSO_TEST_NO_GSO: payload size less than or equal to gso_size
- GSO_TEST_FRAGS: payload in both linear and page frags
- GSO_TEST_FRAGS_PURE: payload exclusively in page frags
- GSO_TEST_GSO_PARTIAL: produce one gso segment of multiple of gso_size,
plus optionally one non-gso trailer segment
Define a test struct that encodes the input gso skb and output segs.
Input in terms of linear and fragment lengths. Output as length of
each segment.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
