Hard-coded stream format parameters are added for Weiss Engineering
FireWire devices. When the device vendor and model match, the parameters
are copied into the stream format cache. This allows for setting all
supported sampling rates up to 192kHz, and consequently adjusting the
number of available I/O channels.
Signed-off-by: Rolf Anderegg <rolf.anderegg@weiss.ch>
Signed-off-by: Michele Perrone <michele.perrone@weiss.ch>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230809002631.750120-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In atmel_conf_pin_config_dbg_show(), checking atmel_pioctrl->pins[pin_id]
against being NULL doesn't make any sense as it gets derefenced first and
the driver's probe() method immediately returns -ENOMEM when devm_kzalloc()
returns NULL for any atmel_pioctrl->pins[] element anyway, thus failing to
register the device...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/4ab2f59f-45c1-76a2-94da-3331e8ec4e35@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The recommended name for enable GPIOs property in regulator-gpio is
"enable-gpios". This is also required by bindings:
ste-hrefv60plus-stuib.dtb: regulator-gpio: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230726070353.103989-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
Fixes: 0f04a81784 ("pinctrl: mcp23s08: Split to three parts: core, I²C, SPI")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621100409.1608395-1-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The exit criteria for the DAA should check if the data length is equal to
1, instead of checking if the response status is equal to 1.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20230802100909.2568215-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Link: https://lore.kernel.org/r/20230802093650.976352-1-chenjiahao16@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After a previous commit changed the driver over to
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(), the suspend/resume
functions must no longer be hidden behind an #ifdef:
In file included from include/linux/clk.h:13,
from drivers/rtc/rtc-stm32.c:8:
drivers/rtc/rtc-stm32.c:927:39: error: 'stm32_rtc_suspend' undeclared here (not in a function); did you mean 'stm32_rtc_probe'?
927 | SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_rtc_suspend, stm32_rtc_resume)
| ^~~~~~~~~~~~~~~~~
include/linux/kernel.h:58:44: note: in definition of macro 'PTR_IF'
58 | #define PTR_IF(cond, ptr) ((cond) ? (ptr) : NULL)
| ^~~
include/linux/pm.h:329:26: note: in expansion of macro 'pm_sleep_ptr'
329 | .suspend_noirq = pm_sleep_ptr(suspend_fn), \
| ^~~~~~~~~~~~
Fixes: fb9a7e5360 ("rtc: stm32: change PM callbacks to "_noirq()"")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230801105932.3738430-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pick up the EEVDF work into the main branch - it's looking good so far.
Conflicts:
kernel/sched/features.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
drm_exec_prepare_obj() and drm_exec_prepare_array() both reserve
dma-fence slots and hence a dma_resv_list without ever freeing it.
Make sure to call drm_gem_private_object_fini() for each GEM object
passed to drm_exec_prepare_obj()/drm_exec_prepare_array() throughout the
test to fix this up.
While at it, remove some trailing empty lines.
Fixes: 9710631cc8 ("drm: add drm_exec selftests v4")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230809225034.8803-1-dakr@redhat.com
Signed-off-by: Christian König <christian.koenig@amd.com>
On the SoC host controller, the pixel clock can be:
* standard: data is launched on the rising edge
* inverted: data is launched on the falling edge
Some panels may need the inverted option to be used so let's support
this DRM flag.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230609144843.851327-1-miquel.raynal@bootlin.com
Panfrost IRQ handler may stuck for a long time, for example this happens
when there is a bad HDMI connection and HDMI handler takes a long time to
finish processing, holding Panfrost. Make Panfrost's job timeout handler
to sync IRQ before checking fence signal status in order to prevent
spurious job timeouts due to a slow IRQ processing.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> # MediaTek MT8192 and MT8195 Chromebooks
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807000444.14926-1-dmitry.osipenko@collabora.com
Not really a common use case, but let's make sure that we don't
accidentially break that somehow.
CC: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731123625.3766-2-christian.koenig@amd.com
GCC forbids to jump to labels in loop conditions and a new clang
check stumbled over this.
So instead using a local label inside the loop condition use an
unique label outside of it.
Fixes: 09593216bf ("drm: execution context for GEM buffers v7")
Link: https://gcc.gnu.org/onlinedocs/gcc/Statement-Exprs.html
Link: https://github.com/ClangBuiltLinux/linux/issues/1890
Link: 2021910606
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
CC: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731123625.3766-1-christian.koenig@amd.com
The dma-buf backend is supposed to provide its own vm_ops, but some
implementation just have nothing special to do and leave vm_ops
untouched, probably expecting this field to be zero initialized (this
is the case with the system_heap implementation for instance).
Let's reset vma->vm_ops to NULL to keep things working with these
implementations.
Fixes: 26d3ac3cb0 ("drm/shmem-helpers: Redirect mmap for imported dma-buf")
Cc: <stable@vger.kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230724112610.60974-1-boris.brezillon@collabora.com
Set on the NFT_SET_ELEM_DEAD_BIT flag on this element, instead of
performing element removal which might race with an ongoing transaction.
Enable gc when dynamic flag is set on since dynset deletion requires
garbage collection after this patch.
Fixes: d0a8d877da ("netfilter: nft_dynset: support for element deletion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the GC transaction API to replace the old and buggy gc API and the
busy mark approach.
No set elements are removed from async garbage collection anymore,
instead the _DEAD bit is set on so the set element is not visible from
lookup path anymore. Async GC enqueues transaction work that might be
aborted and retried later.
rbtree and pipapo set backends does not set on the _DEAD bit from the
sync GC path since this runs in control plane path where mutex is held.
In this case, set elements are deactivated, removed and then released
via RCU callback, sync GC never fails.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Fixes: 8d8540c4f5 ("netfilter: nft_set_rbtree: add timeout support")
Fixes: 9d0982927e ("netfilter: nft_hash: add support for timeouts")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The set types rhashtable and rbtree use a GC worker to reclaim memory.
From system work queue, in periodic intervals, a scan of the table is
done.
The major caveat here is that the nft transaction mutex is not held.
This causes a race between control plane and GC when they attempt to
delete the same element.
We cannot grab the netlink mutex from the work queue, because the
control plane has to wait for the GC work queue in case the set is to be
removed, so we get following deadlock:
cpu 1 cpu2
GC work transaction comes in , lock nft mutex
`acquire nft mutex // BLOCKS
transaction asks to remove the set
set destruction calls cancel_work_sync()
cancel_work_sync will now block forever, because it is waiting for the
mutex the caller already owns.
This patch adds a new API that deals with garbage collection in two
steps:
1) Lockless GC of expired elements sets on the NFT_SET_ELEM_DEAD_BIT
so they are not visible via lookup. Annotate current GC sequence in
the GC transaction. Enqueue GC transaction work as soon as it is
full. If ruleset is updated, then GC transaction is aborted and
retried later.
2) GC work grabs the mutex. If GC sequence has changed then this GC
transaction lost race with control plane, abort it as it contains
stale references to objects and let GC try again later. If the
ruleset is intact, then this GC transaction deactivates and removes
the elements and it uses call_rcu() to destroy elements.
Note that no elements are removed from GC lockless path, the _DEAD bit
is set and pointers are collected. GC catchall does not remove the
elements anymore too. There is a new set->dead flag that is set on to
abort the GC transaction to deal with set->ops->destroy() path which
removes the remaining elements in the set from commit_release, where no
mutex is held.
To deal with GC when mutex is held, which allows safe deactivate and
removal, add sync GC API which releases the set element object via
call_rcu(). This is used by rbtree and pipapo backends which also
perform garbage collection from control plane path.
Since element removal from sets can happen from control plane and
element garbage collection/timeout, it is necessary to keep the set
structure alive until all elements have been deactivated and destroyed.
We cannot do a cancel_work_sync or flush_work in nft_set_destroy because
its called with the transaction mutex held, but the aforementioned async
work queue might be blocked on the very mutex that nft_set_destroy()
callchain is sitting on.
This gives us the choice of ABBA deadlock or UaF.
To avoid both, add set->refs refcount_t member. The GC API can then
increment the set refcount and release it once the elements have been
free'd.
Set backends are adapted to use the GC transaction API in a follow up
patch entitled:
("netfilter: nf_tables: use gc transaction API in set backends")
This is joint work with Florian Westphal.
Fixes: cfed7e1b1f ("netfilter: nf_tables: add set garbage collection helpers")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dhruva reported a build warning with W=1 for "Function parameter or member
'sysconfig' not described in 'sysc'". Let's document sysconfig to fix this.
Reported-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the uart quirks similar to the earlier SoCs. Let's assume we are
likely going to need a k3 specific quirk mask separate from the earlier
SoCs, so let's not start changing the revision register mask at this point.
Note that SYSC_QUIRK_LEGACY_IDLE will be needed until we can remove the
need for pm_runtime_irq_safe() from 8250_omap driver.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow building ti-sysc also for K3 SoCs. This allows configuring the wkup
domain devices for SYSCONFIG register wake-up events in a generic way.
As this is an interconnect level driver, default to built-in on K3 SoCs
to probe the devices connected to the wkup domain like gpio, uart and
timers.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "warning: cast from pointer to integer of different size" on 64-bit
builds.
Note that this is a cosmetic fix at this point as the driver is not yet
used for 64-bit systems.
Fixes: feaa8baee8 ("bus: ti-sysc: Implement SoC revision handling")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a driver for the DW9719 VCM. The driver creates a v4l2 subdevice
and registers a control to set the desired focus.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fill sensor->vcm_type and call intel_cio2_bridge_instantiate_vcm() from
the v4l2-async bound op so that an I2C-client will be instatiated for
the VCM.
Note unfortunately on atomisp the _DSM to get the VCM type sometimes
returns a VCM even though there is none. Since VCMs are typically only
used together with certain sensors, work around this by adding a vcm
field to atomisp_sensor_config and only check for a VCM when that is set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
acpi_handle_info() uses the ACPI path to the handle as prefix for messages
e.g. : "\_SB_.I2C2.CAM8".
This makes it hard for users to figure out which csi2-bridge messages
belong to which sensor since the actual sensor drivers uses the ACPI
device name (typically "HID:00") for logging.
Extend the acpi_handle_info() (and err and warn) logging to also log
the device name to make it easier to match csi2-bridge messages with
sensor driver log messages.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the duplicate IPU ACPI bridge code and use the new
shared ipu_bridge_init() functionality.
Note this will also use / assume v4l2-async device instantiation for
ov5693 sensors on atomisp devices since ipu_supported_sensors[]
already contains a match for this.
This is fine since recent atomisp improvements allow the atomisp code
to work with generic v4l2 sensor drivers and using an unmodified
drivers/media/i2c/ov5693.c has been successfully tested on
an Acer Iconia W4 820 tablet with an ISP2400 + OV5693 sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In most cases when a VCM is used there is a single integrated module
with the sensor + VCM + lens. This means that the sensor and VCM often
share regulators and possibly also something like a powerdown pin.
In the ACPI tables this is modelled as a single ACPI device with
multiple I2cSerialBus resources.
On atomisp devices the regulators and clks are modelled as ACPI
power-resources, which are controlled by the (ACPI) power state
of the sensor. So the sensor must be in D0 power state for the VCM
to work.
To make this work add a device-link with DL_FLAG_PM_RUNTIME flag
so that the sensor will automatically be runtime-resumed whenever
the VCM is runtime-resumed.
This requires the probing of the VCM and thus the creation of the VCM
I2C-client to be delayed till after the sensor driver has bound.
Move the instantiation of the VCM I2C-client to the v4l2_async_notifier
bound op, so that it is done after the sensor driver has bound; and
add code to add the device-link.
This fixes the problem with the shared ACPI power-resources on atomisp2
and this avoids the need for VCM related workarounds on IPU3 / IPU6.
E.g. until now the dw9719 driver needed to get and control a Vsio
(V sensor IO) regulator since that needs to be enabled to enable I2C
pass-through on the PMIC on the sensor module. So the driver was
controlling this regulator even though the actual dw9719 chip has no
Vsio pin / power-plane.
This also removes the need for ipu_bridge_init() to return
-EPROBE_DEFER since the VCM is now instantiated later.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GalaxyCore GC0310 is used together with the atomisp on various
devices, add it to ipu_supported_sensors[].
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move ipu-bridge.h to include/media/, so that it can also be used by
the atomisp code.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a parse_sensor_fwnode() callback to ipu_bridge_init(), so that
ipu_bridge_init() can be used with other sensor fwnode parse functions
then just ipu_bridge_parse_ssdb().
This will allow the ipu3-bridge code to also be used by the atomisp
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
sensor->adev is no longer dereferenced before it is permanently set by:
sensor->adev = acpi_dev_get(adev);
So the early assignment with a borrowed reference can be dropped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The code to go from ACPI sensor info to a fwnode-tree with connector
nodes and endpoint properties is 99% the same for the atomisp2 and
the IPU3.
The main difference is that atomisp2 devices do not have a SSDB table
with various info.
Abstract out the parsing of the sensor's ACPI fwnode into a helper
function and store the parsed results, rather then the raw SSDB
in struct ipu_sensor.
This is a preparation patch for making the ipu-bridge code more generic
so that it can be shared with the atomisp driver.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no need to keep a reference to the PLD struct around,
it is only used once the get the sensor orientation.
Make ipu_bridge_parse_orientation() also get + put the PLD.
This is a preparation patch for making the ipu-bridge code more generic
so that it can be shared with the atomisp driver.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Store the dev pointer in struct ipu_bridge instead of passing it
around 3 levels deep.
This takes up slightly more memory but further patches in this series
add more data which needs to be passed around making passing
everything as arguments cumbersome and those further patches also
add data to struct ipu_bridge.
To be consistent with these upcoming patches also add
the dev pointer to struct ipu_bridge.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names()
where it belongs.
And make the initialization of nodes[SWNODE_VCM] unconditional,
ipu_bridge_init_swnode_group() takes care of not registering it
when there is no VCM.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names()
where it belongs.
And make the initialization of nodes[SWNODE_VCM] unconditional,
ipu_bridge_init_swnode_group() takes care of not registering it
when there is no VCM.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 567f97bd38 ("media: ipu3-cio2: support multiple sensors and VCMs
with same HID") introduced an on stack vcm_name and then uses this for
the name field of the software_node struct used for the vcm.
But the software_node struct is much longer lived then the current
stack-frame, so this is no good.
Instead extend the ipu_node_names struct with an extra field to store
the vcm software_node name and use that.
Note this also changes the length of the allocated buffer from
ACPI_ID_LEN + 4 to 16. the name is filled with "<ipu_vcm_types[x]>-%u"
where ipu_vcm_types[x] is not an ACPI_ID. The maximum length of
the strings in the ipu_vcm_types[] array is 11 + 5 bytes for "-255\0"
means 16 bytes are needed in the worst case scenario.
Fixes: 567f97bd38 ("media: ipu3-cio2: support multiple sensors and VCMs with same HID")
Cc: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When ipu_bridge_parse_rotation() and ipu_bridge_parse_orientation() run
sensor->adev is not set yet.
So if either of the dev_warn() calls about unknown values are hit this
will lead to a NULL pointer deref.
Set sensor->adev earlier, with a borrowed ref to avoid making unrolling
on errors harder, to fix this.
Fixes: 485aa3df0d ("media: ipu3-cio2: Parse sensor orientation and rotation")
Cc: Fabian Wüthrich <me@fabwu.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace a goto-based loop by a while loop.
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for C-PHY on R-Car V4H. While the V4H supports both D-PHY
and C-PHY this patch only adds support for the C-PHY mode due to lack of
documentation and hardware to test on.
The V4H is the first Gen4 device that is enabled in the rcar-csi2
driver. There is much overlap with the Gen3 driver, the primary
difference is in how the receiver is started. The V4H have a much larger
register space and some addresses overlap with Gen3.
[Sakari Ailus: Use div_u64() to divide a 64-bit integer.]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219_set_pad_format() function adjusts the media bus code provided
through the v4l2_subdev_format parameter to a media bus code known
to be supported by the sensor.
The same exact operation is performed by the imx219_get_format_code()
function which called by imx219_update_pad_format(), which is in the
imx219_set_pad_format() call path.
Remove the duplicated operation and simplify imx219_set_pad_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The set_fmt and init_cfg functions both fills a v4l2_mbus_framefmt
instance, passing in the mode and the media bus code. While set_fmt
uses function helpers, init_cfg open-codes the assignments.
Simplify the format initialization by moving it to a common helper.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Port the imx219 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX219 is a RAW sensor. Fix the colorspace configuration by
using V4L2_COLORSPACE_RAW and adjust the quantization and transfer
function values. Drop ycbcr_enc as it doesn't apply to RAW sensors.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Complete the default format initialization in init_cfg() filling in
the fields for the colorspace configuration copied from
imx219_set_default_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the init_cfg pad level operation instead of the internal subdev
open operation to set default formats on the pads.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>