Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The recommended name for enable GPIOs property in regulator-gpio is
"enable-gpios". This is also required by bindings:
imx50-kobo-aura.dtb: gpio-regulator: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixed regulators put under "regulators" node will not be populated,
unless simple-bus or something similar is used. Drop the "regulators"
wrapper node to fix this.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
regulator-fixed-clock does not take "regulator-type" property:
imx6ull-colibri-iris-v2.dtb: regulator-eth-phy: Unevaluated properties are not allowed ('regulator-type' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
regulator-fixed does not take "clock-names" property:
imx6sx-nitrogen6sx.dtb: regulator-wlan: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CSI1 PHY reference clock is limited to 125 MHz according to:
i.MX 8M Mini Applications Processor Reference Manual, Rev. 3, 11/2020
Table 5-1. Clock Root Table (continued) / page 307
Slice Index n = 123 .
Currently the IMX8MM_CLK_CSI1_PHY_REF clock is configured to be
fed directly from 1 GHz PLL2 , which overclocks them. Instead, drop
the configuration altogether, which defaults the clock to 24 MHz REF
clock input, which for the PHY reference clock is just fine.
Based on a patch from Marek Vasut for the imx8mn.
Fixes: e523b7c54c ("arm64: dts: imx8mm: Add CSI nodes")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CSI1 PHY reference clock are limited to 125 MHz according to:
i.MX 8M Nano Applications Processor Reference Manual, Rev. 2, 07/2022
Table 5-1. Clock Root Table (continued) / page 319
Slice Index n = 123 .
Currently those IMX8MN_CLK_CSI1_PHY_REF clock are configured to be
fed directly from 1 GHz PLL2 , which overclocks them . Instead, drop
the configuration altogether, which defaults the clock to 24 MHz REF
clock input, which for the PHY reference clock is just fine.
Fixes: ae9279f301 ("arm64: dts: imx8mn: Add CSI and ISI Nodes")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx genpd was missed to be built out, add it in Makefile
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MX53_PAD_GPIO_1__PWM2_PWMO controls the backlight of the parallel
Seiko display and MX53_PAD_EIM_D24__GPIO3_24 controls the display power.
Reflect that in the devicetree for better description of the board.
Without these entries there is no LCD output on the Seiko display, unless
the bootloader has previously configured these pins.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
mmc0: Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx7s.dtsi#L1216-L1217
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use id-gpios and vbus-gpios instead.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warnings:
at24 0-0053: supply vcc not found, using dummy regulator
at24 0-0057: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 100MHz and 200MHz pinctrl setting for eMMC, and enable 8 bit bus mode
to config the eMMC work at HS400ES mode.
Also update to use Standard Drive Strength for USDHC pad to get a better
signal quality per Hardware team suggests.
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable CM33 node to support rpmsg feature. To use rpmsg, also need
to enable mu node for mailbox doorbell and reserved memory node
for vring, and data buffer. And reserved a piece DRAM memory for case
that m33 images loaded in DRAM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flexspi node, flexspi has a special memory region mapped to
0x60000000~0x6fffffff. This region is for AHB usage. So add this region
to SoC ranges.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add cpuidle node and enable cpuidle for dual cores. The HW mode in
Arm Trusted Firmware is SoC Application Power Domain Sleep mode.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add thermal node. Cooling map is not added, because frequency runtime
changing not supported for now.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set default clock rate and parents for SDHC[0,1,2].
The PLL3 PFD2 maximum frequency is 332Mhz, we can't set it to 389Mhz
as USDHC clock parent. Because PLL3 PFD0 is used for NIC, PFD1 is used
for audio, the only choice is PFD3 which can reach to 400Mhz.
USDHC1 and USDHC2 maximum PCC clock rate is 200Mhz in Over Drive mode,
and 100Mhz in Nominal/Low Drive mode, when PTE or PTF is used.
The patch adjusts clock parent to PLL3 PFD3 DIV1 for USDHC0, PLL3
PFD3 DIV2 for USDHC1 and USDHC2. And set the max rate to meet
restrictions.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable driver for Bluetooth NXP UART applicable amongst others for NXP
88W8997 and IW416 as found on multiple Toradex SoMs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no "vselect-en" property, neither in the bindings nor in the
Linux driver:
imx8mm-phyboard-polis-rdk.dtb: pmic@8: regulators:ldo2: Unevaluated properties are not allowed ('vselect-en' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cadence USB3 bindings specify a specific reg order. Adjust DT entries
to match the bindings.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alias names use dashes instead of underscores, fix this.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alias names use dashes instead of underscores, fix this. Silences also
dtbs_check warning:
imx8qxp-tqma8xqp-mba8xx.dtb: aliases: 'vpu_core0', 'vpu_core1', 'vpu_core2'
do not match any of the regexes: '^[a-z][a-z0-9\\-]*$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/aliases.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warning:
lm75 0-0048: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
HW GEN1 and GEN2 have different min WQ sizes but they are
currently set to the same value.
Use a gen specific attribute min_hw_wq_size and extend ABI to
pass it to user-space.
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/20230725155525.1081-3-shiraz.saleem@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Currently the attribute cap.max_send_wr and cap.max_recv_wr
sent from user-space during create QP are the provider computed
SQ/RQ depth as opposed to raw values passed from application.
This inhibits computation of an accurate value for max_send_wr
and max_recv_wr for this QP in the kernel which matches the value
returned in user create QP. Also these capabilities needs to be
reported from the driver in query QP.
Add support by extending the ABI to allow the raw cap.max_send_wr and
cap.max_recv_wr to be passed from user-space, while keeping compatibility
for the older scheme.
The internal HW depth and shift needed for the WQs needs to be computed
now for both kernel and user-mode QPs. Add new helpers to assist with this:
irdma_uk_calc_depth_shift_sq, irdma_uk_calc_depth_shift_rq and
irdma_uk_calc_depth_shift_wq.
Consolidate all the user mode QP setup into a new function
irdma_setup_umode_qp which keeps it with its counterpart
irdma_setup_kmode_qp.
Signed-off-by: Youvaraj Sagar <youvaraj.sagar@intel.com>
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/20230725155525.1081-2-shiraz.saleem@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW73xx Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with SPI
- off-board I/O connector with I2C, and GPIO
- off-board I/O connector with MIPI DSI, MIPI CSI, I2C, and GPIO
- off-board I/O connector with RS232 and RS485
- EERPOM
- USB 3.0 HUB
- USB 3.0 TypeA socket
- USB 2.0 Micro-B OTG socket
- Accelerometer
- 1x GbE (eQoS)
- 1x GbE (PCI)
- PCIe clock generator
- PCIe switch
- 2x full-length miniPCIe socket with PCI and USB2.0
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) SIM, and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
- on-board 802.11abgnac with Bluetooth 5.2
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW72xx Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with SPI
- off-board I/O connector with I2C, and GPIO
- off-board I/O connector with MIPI DSI, MIPI CSI, I2C, and GPIO
- off-board I/O connector with RS232 and RS485
- EERPOM
- USB 3.0 HUB
- USB 3.0 TypeA socket
- USB 2.0 Micro-B OTG socket
- Accelerometer
- 1x GbE (eQoS)
- 1x GbE (PCI)
- PCIe clock generator
- PCIe switch
- 1x full-length miniPCIe socket with PCI and USB2.0
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) SIM, and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.
The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for a Gateworks GW73xx-2x board based on
the i.MX8M Plus SoC from NXP.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for a Gateworks GW72xx-2x board based on
the i.MX8M Plus SoC from NXP.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for a Gateworks GW71xx-2x board based on
the i.MX8M Plus SoC from NXP.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for a Gateworks GW7905-0x board based on
the i.MX8M Mini from NXP.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These drivers are used on i.MX93 based devices.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the following Raspberry Pi displays:
- DFROBOT DRF0678 7in 800x480 TFT DSI capacitive touch
- DFROBOT DRF0550 5in 800x480 TFT DSI capacitive touch
Both have the following hardware:
- FocalTech FT5406 10pt touch controller (with no interrupt)
- Powertip PH800480T013-IDF02 compatible panel
- Toshiba TC358762 compatible DSI to DBI bridge
- ATTINY based regulator used for backlight controller and panel enable
Support is added via a device-tree overlay. The touch controller is not
yet supported as polling mode is needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB OTG is currently not working for new versions of the Variscite
Symphony EVK and imx8mn nano SOM (versions >= 1.4a).
The PTN5150 circuitry on newer versions of the Symphony EVK board has
a non-standard configuration in which the PTN5150 IRQ pin is left
unconnected, and the PTN5150 ID pin is connected to GPIO1_IO11. This
requires changes to the ptn5150 driver to support this new mode.
Variscite have indicated their intention to submit those changes
upstream.
In the meantime, import device tree changes from linux-5.15 branch of
varigit repos to at least make the USB OTG port operate correctly in
host mode.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Modern GSC firmwares have both static and dynamic MKHI clients.
Avoid expensive dynamic client call for firmware version retrieval,
in case the firmware version is already retrieved from the fix address
client in bus_fixup().
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20230716081043.3092690-3-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable asynchronous suspend for devices on MEI bus,
required for gsc.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20230716081043.3092690-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to extend debug information log firmware status details
when waiting for firmware ready status fails.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20230716081043.3092690-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This source file already includes <linux/miscdevice.h>, which contains
the same macro. It doesn't need to be defined here again.
Fixes: 874bcd00f5 ("apm-emulation: move APM_MINOR_DEV to include/linux/miscdevice.h")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: x86@kernel.org
Cc: Sohil Mehta <sohil.mehta@intel.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20230728011120.759-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, there was no way to query the number of lanes for a network
card, so the same netdev_speed would result in a fixed pair of width and
speed. As network card specifications become more diverse, such fixed
mode is no longer suitable, so a method is needed to obtain the correct
width and speed based on the number of lanes.
This patch retrieves netdev lanes and speed from net_device and
translates them to IB width and speed.
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Signed-off-by: Luoyouming <luoyouming@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20230721092052.2090449-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The PCI function 2 on ASIX AX99100 PCIe to Multi I/O Controller can be
configured as a single-port parallel port controller. The subvendor id
is 0x2000 when configured as parallel port. It supports IEEE-1284 EPP /
ECP with its ECR on BAR1.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20230724083933.3173513-5-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each of the 4 PCI functions on ASIX AX99100 PCIe to Multi I/O
Controller can be configured as a single-port serial port controller.
The subvendor id is 0x1000 when configured as serial port and MSI
interrupts are supported.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230724083933.3173513-4-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>