is check if semaphore is actually locked, which can be trivially done in
portable way. Code gets more reabable, while we are at it...
SGI-PV: 953915
SGI-Modid: xfs-linux-melb:xfs-kern:26274a
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Nathan Scott <nathans@sgi.com>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
All the S3C24XX based devices currently have similar
uart blocks, in the same location. Make the process
of adding new uart blocks easier by commonising the
device definitions and adding a new init function
for the cpu code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform devices for the LEDs on all the SMDK24XX boards
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Also, make sure dirents are marked REF_UNCHECKED when we 'discover' them
through eraseblock summary.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Failing to do so makes the calculated length of the last node incorrect,
when we're not using eraseblock summaries.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from David Brownell
This adds the platform device for SSP/SPI controller, and declares
the ads7846 device hooked up to it. Not all Lubbock boards appear
to populate the connector needed to use this instead of the ucb1400
chip, but it can always be used as a temperature sensor.
In short, this is probably most useful as an example of how to
provide the configuration data used by the pxa2xx_spi driver.
(Last tested against a slightly earlier version of that driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes some dyntick locking issues on ARM as pointed
out by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the printk of the CPU information and IDCODE
before the checking of the table entry validity
to aide in debugging new cpu entries.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Using the low-level debug routines early in the
kernel debug cause the 1:1 mapping to get into
the TLB, which is not flushed until after the
CPU detection process (which needs the GPIO VA).
This patch moves the VA for the GPIO to the
same offset as the physical offset of the UART
to the GPIO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
If CONFIG_CPU_DCACHE_WRITETHOUGH is set, then the
S3C24XX PM code fails to compile, as there is no
need to flush the D-cache, the flush function
arm920_flush_kern_cache_all() is not compiled.
Fix the code to not use this if the config is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The default serial port-mapping for the Osiris has
the port 2 mapped onto the first serial port, and
no port1. Correct this so port 1 is port.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This code was still using the old format for the ARMv6 CPU id and it wasn't
flushing the caches on the MPCore CPU (and other ARM1176 cores). The patch
changes the mask bits to cope with the new id format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gather the common sigmask savbing code inside setup_sigcontext(), and
rename the function setup_sigframe(). Pass it a sigframe structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gather the sigmask restoration code inside restore_sigcontext(), and
rename the function restore_sigframe(). Pass it a sigframe structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sigframe is now a contained subset of rt_sigframe, so we can start
to re-use code which accesses sigframe data for both rt and non-rt
signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ucontext contains both the sigcontext and sigmask structures, and
is also used for rt signal contexts. Re-use this structure for
non-rt signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's not much point in splitting the sigmask between two different
locations, so copy it entirely into a proper sigset_t. This will
eventually allow rt_sigframe and sigframe to share more code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These two members appear to be surplus to requirements. Discussing
this issue with glibc folk:
| > Additionally, do you see any need for these weird "puc" and "pinfo"
| > pointers in the kernels rt_sigframe structure? Can we kill them?
|
| We can kill them. I checked with Phil B. about them last week, and he
| didn't remember any reason they still needed to be there. And nothing
| should know where they are on the stack. Unfortunately, doing this
| will upset GDB, which knows that the saved registers are 0x88 bytes
| above the stack pointer on entrance to an rt signal trampoline; but,
| since puc and pinfo are quite recognizable, I can adapt GDB to support
| the new layout if you want to remove them.
So remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Brook
The old-abi sys_syscall syscall is broken when called from Thumb mode. It
assumes the syscall number is an Arm syscall number (ie. starts from
__NR_OABI_SYSCALL_BASE). In thumb mode syscall numbers start from zero.
The patch below fixes this by clearing the nigh bits of the syscall number
instead of inverting them. Technically this means we accept some invalid
syscall numbers, but I can't see how that could be a problem. The two sets of
numbers far apart that unimplemented syscalls should still be rejected.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds default configuration file PNX4008 ARM platform.
It\'s basically the same as the previos one.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds basic chip support for PNX4008 ARM platform.
It's basically the same as the previous one, but with the rmk's
comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds kernel headers for PNX4008 ARM platform.
It's basically the same as the previos one, but with the rmk's comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
New documentation for the touchscreen controllers and LCD panels.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Reworking of the adaptation macros to allow driver to compile again
for the lpd7x's. Also, support added for the lh79520 so it may use
the smc91x.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Driver for operating SSP devices through LPD7A40X CPLD chip. This
driver is used by the audio codecs.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Board support and LCD panel configurations to integrate lh7a40x's with
the amba clcd driver.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Revised default configuration files.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
The serial driver now sets up the third UART when it is to be used.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x_platform files. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x platform headers. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since parport_serial uses symbols from 8250_pci, there should
be a dependency between the configuration symbols for these
two modules. Problem reported by Andrey Borzenkov
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These include nothing more than the basic set of files listed in
asm-generic/Kbuild.asm. Any extra arch-specific files will need to be
added.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds the Kbuild files listing the files which are to be installed by
the 'headers_install' make target, in generic directories.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Based on the 'headers_install' target, this performs a basic sanity check
on the exported headers -- so far only checking that they do not include
any other headers which aren't selected for import, but easily extendable.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds a make target which exports a subset of headers which contain
definitions which are useful for system libraries and tools. It uses the
BSD 'unifdef' tool to remove instances of #ifdef __KERNEL__, and uses
sed to remove markers like __user.
Based on an original implementation by Arnd Bergmann <arnd@arndb.de>
Hacked about by David Woodhouse <dwmw2@infradead.org>
Reviewed and cleaned up by Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
