Commit 10f6dfcfde (Revert "sch_netem: Remove classful functionality")
reintroduced classful functionality to netem, but broke basic netem
behavior :
netem uses an t(ime)fifo queue, and store timestamps in skb->cb[]
If qdisc is changed, time constraints are not respected and other qdisc
can destroy skb->cb[] and block netem at dequeue time.
Fix this by always using internal tfifo, and optionally attach a child
qdisc to netem (or a tree of qdiscs)
Example of use :
DEV=eth3
tc qdisc del dev $DEV root
tc qdisc add dev $DEV root handle 30: est 1sec 8sec netem delay 20ms 10ms
tc qdisc add dev $DEV handle 40:0 parent 30:0 tbf \
burst 20480 limit 20480 mtu 1514 rate 32000bps
qdisc netem 30: root refcnt 18 limit 1000 delay 20.0ms 10.0ms
Sent 190792 bytes 413 pkt (dropped 0, overlimits 0 requeues 0)
rate 18416bit 3pps backlog 0b 0p requeues 0
qdisc tbf 40: parent 30: rate 256000bit burst 20Kb/8 mpu 0b lat 0us
Sent 190792 bytes 413 pkt (dropped 6, overlimits 10 requeues 0)
backlog 0b 5p requeues 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.
To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
* doing nothing
* reading ipv6 route table via proc
(while :; do cat /proc/net/ipv6_route > /dev/null; done)
* reading ipv6 route table via rtnetlink
(while :; do ip -6 route show table all > /dev/null; done)
* Load the ipv6 route table up with:
* for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done
* iperf commands:
* client: iperf -i 1 -V -c <ipv6 addr>
* server: iperf -V -s
* iperf results - 3 runs each (in Mbits/sec)
* nothing: client: 927,927,927 server: 927,927,927
* proc: client: 179,97,96,113 server: 142,112,133
* iproute: client: 928,927,928 server: 927,927,927
lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: Josh Hunt <joshhunt00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it's not too late fix the recently added RQLEN diag extension
to report rqlen and wqlen in the same way as TCP does.
I.e. for listening sockets the ack backlog length (which is the input
queue length for socket) in rqlen and the max ack backlog length in
wqlen, and what the CINQ/OUTQ ioctls do for established.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Fix indentation of sock_diag*() calls. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a routine that dumps memory-related values of a socket.
It's made as an array to make it possible to add more stuff
here later without breaking compatibility.
Since v1: The SK_MEMINFO_ constants are in userspace
visible part of sock_diag.h, the rest is under __KERNEL__.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The headers check complains it should include the linux/types.h
withing, thus add this one.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly toss existing components around the ifdef __KERNEL__
and include the header into the header-y target.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing (part 2)
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
watchdog: sp805: Fix section mismatch in ID table.
watchdog: move coh901327 state holders
dvb_register calls videobuf_dvb_register_bus, but if that returns
a failure the module will be unloaded without clearing the
value of core->gate_ctrl which will cause an oops in macros
called from video_open in cx88-video.c
Signed-off-by: David Fries <David@Fries.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop dual frontend attach in warm state with single devices.
Since this is a no reconnect device this occurs only after a warm system
reboot.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Re: [git:v4l-dvb/for_v3.3] [media] it9135: add support for IT9135 9005 devices
On Sun, 2011-12-11 at 11:55 +0100, Mauro Carvalho Chehab wrote:
> This is an automatic generated email to let you know that the following patch were queued at the
> http://git.linuxtv.org/media_tree.git tree:
>
> Subject: [media] it9135: add support for IT9135 9005 devices
> Author: Malcolm Priestley <tvboxspy@gmail.com>
> Date: Wed Nov 30 17:16:09 2011 -0300
>
> Support add for IT9135 9005 devices
>
> With this patch IT9135 devices now move to using
> dvb-usb-it9135-01.fw firmware
> IT9137 remain on previous firmware.
Hi Mauro,
I have made a small mistake on this patch.
I forgot to increase number of num_device_descs to 4.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some issues and miss-behaves at the dvb fe thread:
1) dvb_shutdown_timeout should be dvb_shutdown_timeout * HZ
instead of (dvb_shutdown_timeout * HZ + 1);
2) add a memory barrier to warrant that all CPU's will consider the
new value for release_jiffies;
3) wake up dvb thread also when fepriv->exit == DVB_FE_NO_EXIT.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch fixes the automute logic of saa7134.
It avoids the white noise on the pulseaudio startup.
(pulseaudio reads the saa7134 alsa device on startup)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Message-Id: <1322820073-19347-4-git-send-email-xi.wang@gmail.com>
The error handling with (ret < 0) didn't work where ret is a u32.
Use int instead. To be consistent we also change the functions to
return an int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Message-Id: <1322820073-19347-3-git-send-email-xi.wang@gmail.com>
The error handling with (ret < 0) didn't work where ret is a u32.
Use int instead. To be consistent we also change the functions to
return an int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Message-Id: <1322820073-19347-2-git-send-email-xi.wang@gmail.com>
The error handling with (ret < 0) didn't work where ret is a u32.
Use int instead. To be consistent we also change the functions to
return an int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sun4 is no longer supported and this file is unused.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 &
vicam cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that a cut-and-past error were added by the last patch:
drivers/media/video/videobuf2-core.c: In function ‘vb2_qbuf’:
drivers/media/video/videobuf2-core.c:1099:14: warning: comparison between ‘enum v4l2_buf_type’ and ‘enum v4l2_memory’ [-Wenum-compare]
On all places V4L2_MEMORY_USERPTR is used, it is associated with
q->memory, and not b->type. So, the fix seems obvious.
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for user pointer memory buffers to vmalloc
videobuf2 allocator.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is a result of review of mem_priv entry usage in videobuf2 core.
It fixes all all potential places where it was not checked against NULL or
zeroed after freeing as well as a few style issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To get direct access to userspace memory pages vb2 allocator needs to
gather read access on mmap semaphore in the current process.
The same semaphore is taken before calling mmap operation, while
both mmap and qbuf are called by the driver or v4l2 core with
driver's lock held. To avoid a AB-BA deadlock (mmap_sem then
driver's lock in mmap and driver's lock then mmap_sem in qbuf)
the videobuf2 core release driver's lock, takes mmap_sem and then
takes again driver's lock. get_userptr methods are now called with
all needed locks already taken to avoid further lock magic inside
memory allocator's code.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Heuristic that checks if the memory pointer has been changed lacked a check
if the pointer was actually provided by the userspace, what allowed one to
queue a NULL pointer which was accepted without further checking. This
patch fixes this issue.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix the following build warning:
lgdt330x.c: In function "lgdt330x_set_parameters":
lgdt330x.c:346:6: warning: variable "err" set but not used
[-Wunused-but-set-variable]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
initialize *ucblocks to zero & fix the following build warning:
lgdt330x.c: In function "lgdt330x_read_ucblocks":
lgdt330x.c:288:6: warning: variable "err" set but not used
[-Wunused-but-set-variable]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
PCTV290E: Attach a single frontend, rather than a frontend each per
delivery system, whereby a multistandard frontend can advertise all
associated delivery systems.
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Override default delivery system information provided by FE_GET_INFO,
so that applications can enumerate delivery systems provided by the
frontend.
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Hartmut <e9hack@googlemail.com>:
> A break is missing before the default statement. Delivery systems for DVB-C result always
> in an error.
Reported-by: Hartmut <e9hack@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite whole af9013 demod driver in order to decrease I2C I/O.
We need to decrease I2C load since AF9015 (I2C adapter / USB-bridge used)
seems to have some problems under heavy I2C traffic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AF9015 firmware does not like if it gets interrupted by I2C adapter
request on some critical phases. During normal operation I2C adapter
is used only 2nd demodulator and tuner on dual tuner devices.
Override demodulator callbacks and use mutex for limit access to
those "critical" paths to keep AF9015 happy.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
