During probe of each port, read and log the part number from VPD.
Remove the Falcon-specific board name lookup.
Initial version by Stuart Hodgson <smhodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In case all event queues are broken for some reason, this means it
will only take about a second to check them all, rather than up to 32
seconds. This may also speed up testing in the successful case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
IRQ latency can be ridiculously high for various reasons, so our
current timeouts of 100 ms or 10 ms are too short.
Change the IRQ and event tests to use polling loops starting with a
delay of 1 tick and doubling that if necessary up to a maximum total
delay of approximately 1 second.
Raise the loopback packet RX timeout to 1 second.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX and TX completions on the same event queue are generally not associated
with the same flows. The inclusion of TX completions in the adaptive IRQ
score is more of a source of noise rather than useful feedback. Therefore,
do not include them in the score, and adjust the default threshold scores
down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The in-tree driver has never supported Driverlink. The rest of the
comments are rather redundant, but we can usefully state what the
requirements are on the buffer state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Pull s390 regression fix from Martin Schwidefsky:
"It is a fix for a regression that has been introduced with git commit
25f269f173 - "[S390] qdio: EQBS retry after CCQ 96" - and if possible
we would like to have working code for the fcp data router in 3.3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] qdio: fix handler function arguments for zfcp data router
of this driver yet (there's some i.MX platforms which will use it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZXaD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A simple fix that's obvious from inspection. There's no mainline
users of this driver yet (there's some i.MX platforms which will use
it)."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix mask parameter in da9052_reg_update calls
kasprintf() (and potentially other functions that I didn't run across so
far) want to evaluate argument lists twice. Caring to do so for the
primary list is obviously their job, but they can't reasonably be
expected to check the format string for instances of %pV, which however
need special handling too: On architectures like x86-64 (as opposed to
e.g. ix86), using the same argument list twice doesn't produce the
expected results, as an internally managed cursor gets updated during
the first run.
Fix the problem by always acting on a copy of the original list when
handling %pV.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Why is memcg's swap accounting so broken? Insane counts, wrong
ownership, unfreeable structures, which later get freed and then
accessed after free.
Turns out to be a tiny a little 3.3-rc1 regression in 9fb4b7cc07
"page_cgroup: add helper function to get swap_cgroup": the helper
function (actually named lookup_swap_cgroup()) returns an address using
void* arithmetic, but the structure in question is a short.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Bob Liu <lliubbo@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://github.com/hzhuang1/linux: (3 commits)
ARM: pxa: fix invalid mfp pin issue
ARM: pxa: remove duplicated registeration on pxa-gpio
ARM: pxa: add dummy clock for pxa25x and pxa27x
Includes an update to v3.3-rc6
As done for the other ep93xx machines in:
commit 9a6879bd90
ARM: ep93xx: convert to MULTI_IRQ_HANDLER
Now that there is a generic IRQ handler for multiple VIC devices use it
for vision_ep9307 to help building multi platform kernels.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Shared timer IRQs are not a good solution, however the Geode platform has
no APIC, IRQs are a scarce resource and there is no technical reason to
forbid it rightaway. Increased latencies and overhead due to sharing are
still better than a driver refusing to load.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On SMP-capable kernels (e.g. generic distro kernel) the cs5535-clockevt
driver loads but is not actually used.
Setting cpumask to cpu_all_mask works for UP-only kernels, but if compiled
for SMP - though still running on the same UP hardware -
kernel/time/tick-common.c:tick_check_new_device() reads this as
"non-cpu-local" and silently ignores the device.
If we leave cpumask unset clockevents_register_device() will initialize it
and the cs5535-clockevt driver will be used no matter how the kernel was
compiled. Should anyone ever manage to stick a CS553x in an SMP system
(is this even possible?) then a warning will be printed. This is fine as
the cs5535-clockevt driver was never written/tested for SMP.
If bisecting led you here this patch may have exposed a pre-existing MFGPT
problem. Configure for UP-only and re-check.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some quanta devices do not like to be polled for reports
descriptors, thus this quirk.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a list of devices that should be handled by hid-multitouch. They all
present the HID usage "Contact ID" and won't be handled by hid-input. Some of
them have _not_ been tested (though I have their report descriptors), but I've
been guaranted by eeti that they follow the same protocol. The tested ones are
also blacklisted in hid-core.c.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The two invoke_softirq() variants are identical except for a single
line. So move the #ifdef __ARCH_IRQ_EXIT_IRQS_DISABLED inside one of
the functions and get rid of the other one.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In 2008, commit 0c5d1eb77a ("genirq: record trigger type") modified the
way set_irq_type() handles the 'no trigger' condition. However, this has
an adverse effect on PCMCIA support on Intel StrongARM and probably PXA
platforms.
PCMCIA has several status signals on the socket which can trigger
interrupts; some of these status signals depend on the card's mode
(whether it is configured in memory or IO mode). For example, cards have
a 'Ready/IRQ' signal: in memory mode, this provides an indication to
PCMCIA that the card has finished its power up initialization. In IO
mode, it provides the device interrupt signal. Other status signals
switch between on-board battery status and loud speaker output.
In classical PCMCIA implementations, where you have a specific socket
controller, the controller provides a method to mask interrupts from the
socket, and importantly ignore any state transitions on the pins which
correspond with interrupts once masked. This masking prevents unwanted
events caused by the removal and application of socket power being
forwarded.
However, on platforms where there is no socket controller, the PCMCIA
status and interrupt signals are routed to standard edge-triggered GPIOs.
These GPIOs can be configured to interrupt on rising edge, falling edge,
or never. This is where the problems start.
Edge triggered interrupts are required to record events while disabled via
the usual methods of {free,request,disable,enable}_irq() to prevent
problems with dropped interrupts (eg, the 8390 driver uses disable_irq()
to defer the delivery of interrupts). As a result, these interfaces can
not be used to implement the desired behaviour.
The side effect of this is that if the 'Ready/IRQ' GPIO is disabled via
disable_irq() on suspend, and enabled via enable_irq() after resume, we
will record the state transitions caused by powering events as valid
interrupts, and foward them to the card driver, which may attempt to
access a card which is not powered up.
This leads delays resume while drivers spin in their interrupt handlers,
and complaints from drivers before they realize what's happened.
Moreover, in the case of the 'Ready/IRQ' signal, this is requested and
freed by the card driver itself; the PCMCIA core has no idea whether the
interrupt is requested, and, therefore, whether a call to disable_irq()
would be valid. (We tried this around 2.4.17 / 2.5.1 kernel era, and
ended up throwing it out because of this problem.)
Therefore, it was decided back in around 2002 to disable the edge
triggering instead, resulting in all state transitions on the GPIO being
ignored. That's what we actually need the hardware to do.
The commit above changes this behaviour; it explicitly prevents the 'no
trigger' state being selected.
The reason that request_irq() does not accept the 'no trigger' state is
for compatibility with existing drivers which do not provide their desired
triggering configuration. The set_irq_type() function is 'new' and not
used by non-trigger aware drivers.
Therefore, revert this change, and restore previously working platforms
back to their former state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux@arm.linux.org.uk
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for unknown Waltop tablet with product ID 0x0038.
This tablet is sold as Genius G-Pen F509.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace original report descriptor dumps in the comments with links to tablet
descriptions in a wiki, to make code clearer.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace original report descriptor dumps in the comments with links to tablet
descriptions in a wiki, to make code clearer.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My CD input got lost in commit 68ef0561ef.
Raymond helped me to add the necessary pin fixup to make it appear again. In
fact, this is basically his patch. It fixes alsa bug #5541.
Signed-off-by: Marton Balint <cus@passwd.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a bug in kprobes which can modify kernel code
permanently at run-time. In the result, kernel can
crash when it executes the modified code.
This bug can happen when we put two probes enough near
and the first probe is optimized. When the second probe
is set up, it copies a byte which is already modified
by the first probe, and executes it when the probe is hit.
Even worse, the first probe and the second probe are removed
respectively, the second probe writes back the copied
(modified) instruction.
To fix this bug, kprobes always recovers the original
code and copies the first byte from recovered instruction.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133215.5982.31991.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current probed-instruction recovery expects that only breakpoint
instruction modifies instruction. However, since kprobes jump
optimization can replace original instructions with a jump,
that expectation is not enough. And it may cause instruction
decoding failure on the function where an optimized probe
already exists.
This bug can reproduce easily as below:
1) find a target function address (any kprobe-able function is OK)
$ grep __secure_computing /proc/kallsyms
ffffffff810c19d0 T __secure_computing
2) decode the function
$ objdump -d vmlinux --start-address=0xffffffff810c19d0 --stop-address=0xffffffff810c19eb
vmlinux: file format elf64-x86-64
Disassembly of section .text:
ffffffff810c19d0 <__secure_computing>:
ffffffff810c19d0: 55 push %rbp
ffffffff810c19d1: 48 89 e5 mov %rsp,%rbp
ffffffff810c19d4: e8 67 8f 72 00 callq
ffffffff817ea940 <mcount>
ffffffff810c19d9: 65 48 8b 04 25 40 b8 mov %gs:0xb840,%rax
ffffffff810c19e0: 00 00
ffffffff810c19e2: 83 b8 88 05 00 00 01 cmpl $0x1,0x588(%rax)
ffffffff810c19e9: 74 05 je ffffffff810c19f0 <__secure_computing+0x20>
3) put a kprobe-event at an optimize-able place, where no
call/jump places within the 5 bytes.
$ su -
# cd /sys/kernel/debug/tracing
# echo p __secure_computing+0x9 > kprobe_events
4) enable it and check it is optimized.
# echo 1 > events/kprobes/p___secure_computing_9/enable
# cat ../kprobes/list
ffffffff810c19d9 k __secure_computing+0x9 [OPTIMIZED]
5) put another kprobe on an instruction after previous probe in
the same function.
# echo p __secure_computing+0x12 >> kprobe_events
bash: echo: write error: Invalid argument
# dmesg | tail -n 1
[ 1666.500016] Probing address(0xffffffff810c19e2) is not an instruction boundary.
6) however, if the kprobes optimization is disabled, it works.
# echo 0 > /proc/sys/debug/kprobes-optimization
# cat ../kprobes/list
ffffffff810c19d9 k __secure_computing+0x9
# echo p __secure_computing+0x12 >> kprobe_events
(no error)
This is because kprobes doesn't recover the instruction
which is overwritten with a relative jump by another kprobe
when finding instruction boundary.
It only recovers the breakpoint instruction.
This patch fixes kprobes to recover such instructions.
With this fix:
# echo p __secure_computing+0x9 > kprobe_events
# echo 1 > events/kprobes/p___secure_computing_9/enable
# cat ../kprobes/list
ffffffff810c1aa9 k __secure_computing+0x9 [OPTIMIZED]
# echo p __secure_computing+0x12 >> kprobe_events
# cat ../kprobes/list
ffffffff810c1aa9 k __secure_computing+0x9 [OPTIMIZED]
ffffffff810c1ab2 k __secure_computing+0x12 [DISABLED]
Changes in v4:
- Fix a bug to ensure optimized probe is really optimized
by jump.
- Remove kprobe_optready() dependency.
- Cleanup code for preparing optprobe separation.
Changes in v3:
- Fix a build error when CONFIG_OPTPROBE=n. (Thanks, Ingo!)
To fix the error, split optprobe instruction recovering
path from kprobes path.
- Cleanup comments/styles.
Changes in v2:
- Fix a bug to recover original instruction address in
RIP-relative instruction fixup.
- Moved on tip/master.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133209.5982.36568.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The number of IOMMUs supported should be the same as the number
of IO APICS. This limit comes into play when the IOMMUs are
identity mapped, thus the number of possible IOMMUs in the
"static identity" (si) domain should be this same number.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Daniel Rahn <drahn@suse.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
[ Fixed printk format string, cleaned up the code ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-ixcmp0hfp0a3b2lfv3uo0p0x@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With SandyBridge, Intel has changed these Socket PCI devices to
have a class type of "System Peripheral" & "Performance
counter", rather than "HostBridge".
So instead of using a "special" case to detect which devices will
not be doing DMA, use the fact that a device that is not associated
with an IOMMU, will not need an identity map.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Mike Habeck <habeck@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Daniel Rahn <drahn@suse.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-018fywmjs3lmzfyzjlktg8dx@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Failure is reported on hx4700 with kernel v3.3-rc1.
__mfp_validate: GPIO20 is invalid pin
__mfp_validate: GPIO21 is invalid pin
__mfp_validate: GPIO15 is invalid pin
__mfp_validate: GPIO78 is invalid pin
__mfp_validate: GPIO79 is invalid pin
__mfp_validate: GPIO80 is invalid pin
__mfp_validate: GPIO33 is invalid pin
__mfp_validate: GPIO48 is invalid pin
__mfp_validate: GPIO49 is invalid pin
__mfp_validate: GPIO50 is invalid pin
Since pxa_last_gpio is used in mfp-pxa2xx driver. But it's only
updated in pxa-gpio driver that run after mfp-pxa2xx driver.
So update the pxa_last_gpio first in mfp-pxa2xx driver.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Both reboot (via reboot(RB_AUTOBOOT)) and suspend freeze on hx4700.
Registration of pxa_gpio_syscore_ops is moved into pxa-gpio driver,
but it still exists in arch-pxa directory. It resulsts failure on
reboot and suspend.
Now remove the registration code in arch-pxa.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
This regression was introduced by the commit "ARM: pxa: add dummy
clock for sa1100-rtc", id a55b5adaf4.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"It contains three cherry-picked fixes from perf/core, which turned out
to be more urgent than we originally thought."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Handle kernels that don't support attr.exclude_{guest,host}
perf tools: Change perf_guest default back to false
perf record: No build id option fails
There is just one patch in here, a revert of a powerpc EHCI driver
patch that was reported to cause problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9VTXkACgkQMUfUDdst+ylV+wCg0LCngetBRR4J7Tu+fxfIBS00
z6YAni9fZFigFsapZqiypbSVrZ6FARQs
=g7Br
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB: revert a powerpc EHCI patch
There is just one patch in here, a revert of a powerpc EHCI driver
patch that was reported to cause problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "powerpc/usb: fix issue of CPU halt when missing USB PHY clock"
This contains one build fix for the powerpc udbg driver that was reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9VTK0ACgkQMUfUDdst+ykAGACeLDYE9U586NNUAGcHALtb6AtT
R1IAoK4NgsUvzxkp8XOlUYUar1DulcZB
=0xfn
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
tty: build fix for 3.3-rc6
This contains one build fix for the powerpc udbg driver that was reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/powerpc: early udbg consoles can't be modules
2 relate to the recently added drive replacement.
One causes read error in RAID10 to sometimes be retried indefinitely.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=93ms
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three fixes for md in 3.3-rc: Two relate to the recently added drive
replacement. One fixes the problem where a read error in RAID10 would
sometimes be retried indefinitely."
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md/raid10: fix assembling of arrays with replacement devices.
md/raid10: fix handling of error on last working device in array.
md/raid1: fix buglet in md_raid1_contested.
Merge the emailed seties of 19 patches from Andrew Morton
* akpm:
rapidio/tsi721: fix queue wrapping bug in inbound doorbell handler
memcg: fix mapcount check in move charge code for anonymous page
mm: thp: fix BUG on mm->nr_ptes
alpha: fix 32/64-bit bug in futex support
memcg: fix GPF when cgroup removal races with last exit
debugobjects: Fix selftest for static warnings
floppy/scsi: fix setting of BIO flags
memcg: fix deadlock by inverting lrucare nesting
drivers/rtc/rtc-r9701.c: fix crash in r9701_remove()
c2port: class_create() returns an ERR_PTR
pps: class_create() returns an ERR_PTR, not NULL
hung_task: fix the broken rcu_lock_break() logic
vfork: kill PF_STARTING
coredump_wait: don't call complete_vfork_done()
vfork: make it killable
vfork: introduce complete_vfork_done()
aio: wake up waiters when freeing unused kiocbs
kprobes: return proper error code from register_kprobe()
kmsg_dump: don't run on non-error paths by default
