We need to return QLA_FUNCTION_TIMEOUT immediately otherwise we mess up the
mailbox command state machine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If there is an error creating multiple response queues then we need to revert
the request queue mapping back to request queue 0.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This function can wait for 5min under certain scenarios. One of them is when
the port is down from switch and bus reset is issued. The bus reset used to
wait for 5 minutes for the loop and upper layer callers used to hang and give
stack trace because of getting stuck for 120 sec. It is legacy code that was
used when the driver used to do queuing of the commands.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
_scsih_smart_predicted_fault is called in an interrupt and therefore
must allocate memory using GFP_ATOMIC.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads on several Dell laptops, particularly Vostro V13
systems, may not respond properly to PS/2 commands and queries immediately
after resuming from suspend to RAM. This leads to unresponsive touchpad
after suspend/resume cycle.
Adding a 1-second delay after resetting the device allows touchpad to
finish initializing (calibrating?) and start reacting properly.
Reported-by: Daniel Manrique <daniel.manrique@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Register input device last so that we do not have to reset
input device pointer after calling input_unregister_device().
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The error check (intr_status < 0) didn't work because intr_status is
a u8. Change its type to signed int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New product ID reported by Harvey Braun on linuxwacom mailing list
and also tested this patch with new hardware.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds the .gitignore file for the autogenerated TOMOYO files to keep
git from complaining after building things.
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
To support advanced system functionality for additional components; the
actively used clocks will remain the same for current components. Also
factor the rate out to a single #define while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a partial revert of 42b2aa86c6 ("treewide: Fix typos in
various parts of the kernel, and fix some comments") as the code
has been refactored in the wireless tree.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We depend on memless force-feedback support, therefore correctly select the
related config options.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable Tx vlan offloading in certain cases.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update pmem_fifo_overflow_drop, rx_priority_pause_frames counters.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arm_dma_zone_size is used by arm_bootmem_free() which is called by
paging_init(). Thus it needs to be set before calling it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove set but not used variables to fix warnings.
HOSTCC scripts/kconfig/gconf.o
/usr/src/lto/scripts/kconfig/gconf.c: In function 'change_sym_value':
/usr/src/lto/scripts/kconfig/gconf.c:833:11: warning: variable 'oldval' set but not used [-Wunused-but-set-variable]
/usr/src/lto/scripts/kconfig/gconf.c: In function 'update_tree':
/usr/src/lto/scripts/kconfig/gconf.c:1281:19: warning: variable 'prop' set but not used [-Wunused-but-set-variable]
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Specify format arguments to fix warnings.
HOSTCC scripts/kconfig/gconf.o
/usr/src/lto/scripts/kconfig/gconf.c: In function 'on_introduction1_activate':
/usr/src/lto/scripts/kconfig/gconf.c:686:6: warning: format not a string literal and no format arguments
/usr/src/lto/scripts/kconfig/gconf.c: In function 'on_about1_activate':
/usr/src/lto/scripts/kconfig/gconf.c:704:6: warning: format not a string literal and no format arguments
/usr/src/lto/scripts/kconfig/gconf.c: In function 'on_license1_activate':
/usr/src/lto/scripts/kconfig/gconf.c:723:6: warning: format not a string literal and no format arguments
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Both TINY_RCU's and TREE_RCU's implementations of rcu_boost() access
the ->boost_tasks and ->exp_tasks fields without preventing concurrent
changes to these fields. This commit therefore applies ACCESS_ONCE in
order to prevent compiler mischief.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This reverts commit 5342e269b2.
The approach taken in this patch was deemed too abusive to mutexes,
and thus too likely to result in maintenance problems in the future.
Instead, we will disallow RCU read-side critical sections that partially
overlap with interrupt-disbled code segments.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tyler Hicks pointed me at an additional article on RCU and I figured
it should probably be mentioned with the others.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The current rcu_batch_end event trace records only the name of the RCU
flavor and the total number of callbacks that remain queued on the
current CPU. This is insufficient for testing and tuning the new
dyntick-idle RCU_FAST_NO_HZ code, so this commit adds idle state along
with whether or not any of the callbacks that were ready to invoke
at the beginning of rcu_do_batch() are still queued.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds simple rcutorture tests for srcu_read_lock_raw() and
srcu_read_unlock_raw(). It does not test doing srcu_read_lock_raw()
in an exception handler and releasing it in the corresponding process
context.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcutorture test now can automatically exercise CPU hotplug and
collect success statistics, which can be correlated with other rcutorture
activity. This permits rcutorture to completely exercise RCU regardless
of what sort of userspace and filesystem layout is in use. Unfortunately,
rcutorture is happy to attempt to offline CPUs that cannot be offlined,
for example, CPU 0 in both the x86 and ARM architectures. Although this
allows rcutorture testing to proceed normally, it confounds attempts at
error analysis due to the resulting flood of spurious CPU-hotplug errors.
Therefore, this commit uses the new cpu_is_hotpluggable() function to
avoid attempting to offline CPUs that are not hotpluggable, which in
turn avoids spurious CPU-hotplug errors.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
When architectures register CPUs, they indicate whether the CPU allows
hotplugging; notably, x86 and ARM don't allow hotplugging CPU 0.
Userspace can easily query the hotpluggability of a CPU via sysfs;
however, the kernel has no convenient way of accessing that property in
an architecture-independent way. While the kernel can simply try it and
see, some code needs to distinguish between "hotplug failed" and
"hotplug has no hope of working on this CPU"; for example, rcutorture's
CPU hotplug tests want to avoid drowning out real hotplug failures with
expected failures.
Expose this property via a new cpu_is_hotpluggable function, so that the
rest of the kernel can access it in an architecture-independent way.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
No point in having two identical rcu_cpu_stall_suppress declarations,
so remove the more obscure of the two.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If there are other CPUs active at a given point in time, then there is a
limit to what a given CPU can do to advance the current RCU grace period.
Beyond this limit, attempting to force the RCU grace period forward will
do nothing but consume energy burning CPU cycles.
Therefore, this commit takes an adaptive approach to RCU_FAST_NO_HZ
preparations for idle. It pushes the RCU core state machine for
two cycles unconditionally, and then it will push from zero to three
additional cycles, but only as long as the RCU core has work for this
CPU to do immediately. The rcu_pending() function is used to check
whether the RCU core has such work.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_do_batch() function that invokes callbacks for TREE_RCU and
TREE_PREEMPT_RCU normally throttles callback invocation to avoid degrading
scheduling latency. However, as long as the CPU would otherwise be idle,
there is no downside to continuing to invoke any callbacks that have passed
through their grace periods. In fact, processing such callbacks in a
timely manner has the benefit of increasing the probability that the
CPU can enter the power-saving dyntick-idle mode.
Therefore, this commit allows callback invocation to continue beyond the
preset limit as long as the scheduler does not have some other task to
run and as long as context is that of the idle task or the relevant
RCU kthread.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Because tasks don't nest, the ->dyntick_nesting must always be zero upon
entry to rcu_idle_enter_common(). Therefore, pass "0" rather than the
counter itself.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
