Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move add_wired_entry to its own header file from where it will be
always included. Patch up other users of add_wired_entry to also include
the header as needed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move PCI Controller PM to syscore_ops since the platform_driver PM methods
are called way too late on resume and far too early on suspend (after and
before PCI device resume/suspend).
This also allows to simplify wired entry management a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disabling all runtime PM during system shutdown turns out not to be a
good idea, because some devices may need to be woken up from a
low-power state at that time.
The whole point of disabling runtime PM for system shutdown was to
prevent untimely runtime-suspend method calls. This patch (as1504)
accomplishes the same result by incrementing the usage count for each
device and waiting for ongoing runtime-PM callbacks to finish. This
is what we already do during system suspend and hibernation, which
makes sense since the shutdown method is pretty much a legacy analog
of the pm->poweroff method.
This fixes a recent regression on some OMAP systems introduced by
commit af8db1508f (PM / driver core:
disable device's runtime PM during shutdown).
Reported-and-tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes:
The function __devinit spi_gpio_probe() references
a function __init spi_gpio_alloc.isra.4().
If spi_gpio_alloc.isra.4 is only used by spi_gpio_probe then
annotate spi_gpio_alloc.isra.4 with a matching annotation.
[wsa: fix spi_gpio_request(), too]
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When spi_fsl_espi is chosen to be built as a module, there is a build
error because we test only CONFIG_SPI_FSL_ESPI in declaration of
struct mpc8xxx_spi in drivers/spi/spi_fsl_lib.h. Also some called
functions are not exported.
So we forbid CONFIG_SPI_FSL_ESPI to be tristate here.
The error looks like:
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_bufs':
drivers/spi/spi_fsl_espi.c:232: error: 'struct mpc8xxx_spi' has no member named 'len'
...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Include linux/module.h to fix below build error:
CC drivers/spi/spi-nuc900.o
drivers/spi/spi-nuc900.c:484: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/spi/spi-nuc900.c:489: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:489: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:489: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/spi/spi-nuc900.c:489: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:490: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:490: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:490: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/spi/spi-nuc900.c:490: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:491: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:491: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:491: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/spi/spi-nuc900.c:491: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:492: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:492: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:492: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
drivers/spi/spi-nuc900.c:492: warning: function declaration isn't a prototype
make[2]: *** [drivers/spi/spi-nuc900.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Whithout including 'linux/module.h' spi-ath79 driver fails to compile
with the these errors:
drivers/spi/spi-ath79.c:273:12: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/spi/spi-ath79.c:278:20: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:278:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:278:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/spi/spi-ath79.c:278:20: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:279:15: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:279:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:279:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/spi/spi-ath79.c:279:15: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:280:16: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:280:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:280:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/spi/spi-ath79.c:280:16: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:281:14: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:281:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:281:1: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
drivers/spi/spi-ath79.c:281:14: warning: function declaration isn't a prototype
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
v2: cache_register_net() and cache_unregister_net() GPL exports added
This is a cleanup patch. Hope, some day generic cache_register() and
cache_unregister() will be removed.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This code has been on the list to remove for a long
time, so disable it by default, add a warning to its
Kconfig, and schedule it for removal in 3.5.
The only known dependency, hal, has not required it
since its 0.5.12 release, which was in early 2009
and hal has since been deprecated completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable ANI for ar9100 since it seems to be working fine (and as a
matter of fact ANI was always performed for ar9100 since code which
was supposed to disable it didn't achieve this goal).
This patch sets config.enable_ani to default (true) value for
ar9100.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debugging write a log entry when long calibration, short
calibration or ANI is performed.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missed space and change typo in calibration debugging log.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recently more places in mac80211 call drv_flush to ensure proper order
for state changes wrt. powersave, channel changes, etc. On some systems
such calls lead to spurious logspam about failing to stop tx dma, as well
as hardware resets that go along with that.
Instead of dropping packets in a place where it's completely unnecessary,
only do it when drop == true.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turning off the radio when mac80211 tells the driver that it's idle is not
a good idea, as idle interfaces might still occasionally scan or send packets.
The only time the radio can be safely turned off is when drv_stop has been
called. In the mean time, use sc->ps_idle only to indicate network sleep vs
full sleep.
Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop
functions already take care of that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After waking up from full sleep, registers are accessible, but rx/tx
typically fails. A fast channel change will not recover from this, so
ensure that a full-sleep -> wake transition is always followed by a full
reset.
The reason why this hasn't created any serious problems yet is that it's
hidden by the (wrong) behavior of enabling/disabling the radio when the
wiphy idle state changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In drivers rtl8192ce, rtl8192cu, rtl8192se, and rtl8192de, break
statements would allow ppsc->rfpwr_state to be changed to ERFSLEEP
even though the device is actually in ERFOFF.
Signed-off-by: Philipp Dreimann <philipp@dreimann.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel noticed that when mac80211 stops the queues
for aggregation that can leave a packet pending. This
packet will be given to the driver after the AMPDU
callback, but as a non-aggregated packet which messes
up the sequence number etc.
I also noticed by looking at the code that if packets
are being processed while we clear the WANT_START bit,
they might see it cleared already and queue up on
tid_tx->pending. If the driver then rejects the new
aggregation session we leak the packet.
Fix both of these issues by changing this code to not
stop the queues at all. Instead, let packets queue up
on the tid_tx->pending queue instead of letting them
get to the driver, and add code to recover properly
in case the driver rejects the session.
(The patch looks large because it has to move two
functions to before their new use.)
Cc: stable@vger.kernel.org
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit: 6b2f55d785,
is adding the support for the CONFIG_MULTI_IRQ_HANDLER but did
not update all the machine descriptors supported in the DT
board-generic.c file.
It thus break the DT boot on OMAP3 and OMAP4 boards.
Add the proper handle_irq callbacks for OMAP3 and OMAP4 generic
machine descriptors.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been using i_lock to protect all kinds of data structures in the
ceph_inode_info struct, including lists of inodes that we need to iterate
over while avoiding races with inode destruction. That requires grabbing
a reference to the inode with the list lock protected, but igrab() now
takes i_lock to check the inode flags.
Changing the list lock ordering would be a painful process.
However, using a ceph-specific i_ceph_lock in the ceph inode instead of
i_lock is a simple mechanical change and avoids the ordering constraints
imposed by igrab().
Reported-by: Amon Ott <a.ott@m-privacy.de>
Signed-off-by: Sage Weil <sage@newdream.net>
This doesn't interact with resizing well, since it doesn't set the
size of the device to the size at the snapshot. It's also an expensive
operation to be synchronous. Rollback can still be done with the
userspace rbd tool.
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
The pdev->id is used in several places for different purpose. All
these uses assume it's always the id of fec device which is >= 0.
However this is only true for non-DT case. When DT plays, pdev->id
is always -1, which will break these pdev->id users.
Instead of fixing all these users one by one, this patch introduces
a new member 'dev_id' to 'struct fec_enet_private' for holding the
correct fec device id, and replaces all the existing uses of pdev->id
with this dev_id.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPC32/64 defines NO_IRQ to zero, so no problems expected.
ARM defines NO_IRQ to -1, but OF code relies on IRQ domains support,
which returns correct ('0') value in 'no irq' case. So everything
should be fine.
Other arches might break if some of their OF drivers rely on NO_IRQ
being not 0. If so, the drivers must be fixed, finally.
[ Rob Herring points out that microblaze should be fixed, and has posted
a patch for testing for that. - Linus ]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When there are the same or more number of HP pins are available, HP pins
are used as the primary outputs instead of the speaker pins. But, in
some cases (especially with ALC663 & co), some DACs are available only
with a later pin and it's assigned to a speaker, and since the driver
parses the pins from the lower NID, such a DAC was skipped eventually
without assignments. This resulted in a regression, the missing speaker
volume control in the new parser.
As a workaround for this, now the driver retries the pin->DAC mapping
again after restoring the speaker-pins as primary. This is still an ad
hoc fix, but it works so far for most of Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On systems with two speaker pins, the secondary speaker pin is mostly
assigned to a bass speaker instead of a surround. Thus it makes more
sense to rename the control properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multiple headphone or speaker pins are usually provided to
output the same stream unlike line-out jacks (which are supposed
to be multi-channel surrounds). Thus giving a mixer name like
"Headphone Surround" is rather confusing. Instead, when multiple
headphone volumes are available, use index with the same "Headphone"
name.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vmwgfx: Use kcalloc instead of kzalloc to allocate array
drm/i915: fix infinite recursion on unbind due to ilk vt-d w/a
drm/radeon/kms: fix return type for radeon_encoder_get_dp_bridge_encoder_id
Fix a typo introduced by commit e00c3f55
"ASoC: Convert Samsung directory to module_platform_driver".
This fixes the build error:
CC sound/soc/samsung/s3c24xx_simtec_tlv320aic23.o
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c: In function 'simtec_audio_tlv320aic32_driver_init':
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: 'simtec_audio_tlv320aic32_driver' undeclared (first use in this function)
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: (Each undeclared identifier is reported only once
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: for each function it appears in.)
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c: In function 'simtec_audio_tlv320aic32_driver_exit':
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: 'simtec_audio_tlv320aic32_driver' undeclared (first use in this function)
make[3]: *** [sound/soc/samsung/s3c24xx_simtec_tlv320aic23.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
I think we had better naming it with *driver, thus I change
it to simtec_audio_tlv320aic23_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Include linux/module.h to fix below build error:
CC sound/soc/samsung/smdk2443_wm9710.o
sound/soc/samsung/smdk2443_wm9710.c:64: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:64: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:64: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
sound/soc/samsung/smdk2443_wm9710.c:64: warning: function declaration isn't a prototype
sound/soc/samsung/smdk2443_wm9710.c:65: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:65: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:65: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
sound/soc/samsung/smdk2443_wm9710.c:65: warning: function declaration isn't a prototype
sound/soc/samsung/smdk2443_wm9710.c:66: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:66: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:66: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
sound/soc/samsung/smdk2443_wm9710.c:66: warning: function declaration isn't a prototype
make[3]: *** [sound/soc/samsung/smdk2443_wm9710.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
