The "BCLR" in CFIFOCTR/DnFIFOCTR can flush the fifo of "CPU side" only.
To flush the fifo of "SIE side", we have to use the "ACLRM" in PIPEnCTR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The udc-newstyle needs device_register in probe() of platform_device.
If it doesn't call, kernel panic happens in the sysfs_create_dir() when
we run modprobe a gadget driver.
[ balbi@ti.com : fix compile warning introduced by this patch ]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those are simply giving information about the current
state of the UDC, nothing really fancy. We can let
everybody read those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_gadget_disconnect() is responsible of removing
data pullups. Before doing that we must, first, tell
gadget driver we're disconnecting (by calling disconnect
method on gadget driver structure), unbind the gadget
driver and stop the controller.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
that has already being done by udc-core.c. It's
unnecessary and might cause issues with some gadget
drivers.
Tested: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when dev_hard_header() failed, the newly allocated skb should be freed.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for NLM_F_* flags at IPv6 routing requests.
If NLM_F_CREATE flag is not defined for RTM_NEWROUTE request,
warning is printed, but no error is returned. Instead new route is
added. Later NLM_F_CREATE may be required for
new route creation.
Exception is when NLM_F_REPLACE flag is given without NLM_F_CREATE, and
no matching route is found. In this case it should be safe to assume
that the request issuer is familiar with NLM_F_* flags, and does really
not want route to be created.
Specifying NLM_F_REPLACE flag will now make the kernel to search for
matching route, and replace it with new one. If no route is found and
NLM_F_CREATE is specified as well, then new route is created.
Also, specifying NLM_F_EXCL will yield returning of error if matching
route is found.
Patch created against linux-3.2-rc1
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for NLM_F_* flags at IPv6 routing requests.
Warn if NLM_F_CREATE flag is not defined for RTM_NEWROUTE request,
creating new table. Later NLM_F_CREATE may be required for
new route creation.
Patch created against linux-3.2-rc1
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lantiq ETOP ethernet driver fails to build in 3.2-rc1 due to 2 missing
header files.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-usb-linus' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
usb, xhci: Clear warm reset change event during init
xhci: Set slot and ep0 flags for address command.
usb, xhci: fix lockdep warning on endpoint timeout
This patch fixes an issue introduced recently with commit
452448f928.
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HW doesn't remove FCS bytes they are reported in the completion
byte count, we don't need to take them to skb.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x uses following formula to compute its rx_buf_sz :
dev->mtu + 2*L1_CACHE_BYTES + 14 + 8 + 8 + 2
Then core network adds NET_SKB_PAD and SKB_DATA_ALIGN(sizeof(struct
skb_shared_info))
Final allocated size for skb head on x86_64 (L1_CACHE_BYTES = 64,
MTU=1500) : 2112 bytes : SLUB/SLAB round this to 4096 bytes.
Since skb truesize is then bigger than SK_MEM_QUANTUM, we have lot of
false sharing because of mem_reclaim in UDP stack.
One possible way to half truesize is to reduce the need by 64 bytes
(2112 -> 2048 bytes)
Instead of allocating a full cache line at the end of packet for
alignment, we can use the fact that skb_shared_info sits at the end of
skb->head, and we can use this room, if we convert bnx2x to new
build_skb() infrastructure.
skb_shared_info will be initialized after hardware finished its
transfert, so we can eventually overwrite the final padding.
Using build_skb() also reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are recycled while still hot.
Performance results :
(820.000 pps on a rx UDP monothread benchmark, instead of 720.000 pps)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Tom Herbert <therbert@google.com>
CC: Jamal Hadi Salim <hadi@mojatatu.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Thomas Graf <tgraf@infradead.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the thing we discussed during netdev 2011 conference was the idea
to change some network drivers to allocate/populate their skb at RX
completion time, right before feeding the skb to network stack.
In old days, we allocated skbs when populating the RX ring.
This means bringing into cpu cache sk_buff and skb_shared_info cache
lines (since we clear/initialize them), then 'queue' skb->data to NIC.
By the time NIC fills a frame in skb->data buffer and host can process
it, cpu probably threw away the cache lines from its caches, because lot
of things happened between the allocation and final use.
So the deal would be to allocate only the data buffer for the NIC to
populate its RX ring buffer. And use build_skb() at RX completion to
attach a data buffer (now filled with an ethernet frame) to a new skb,
initialize the skb_shared_info portion, and give the hot skb to network
stack.
build_skb() is the function to allocate an skb, caller providing the
data buffer that should be attached to it. Drivers are expected to call
skb_reserve() right after build_skb() to adjust skb->data to the
Ethernet frame (usually skipping NET_SKB_PAD and NET_IP_ALIGN, but some
drivers might add a hardware provided alignment)
Data provided to build_skb() MUST have been allocated by a prior
kmalloc() call, with enough room to add SKB_DATA_ALIGN(sizeof(struct
skb_shared_info)) bytes at the end of the data without corrupting
incoming frame.
data = kmalloc(NET_SKB_PAD + NET_IP_ALIGN + 1536 +
SKB_DATA_ALIGN(sizeof(struct skb_shared_info)),
GFP_ATOMIC);
...
skb = build_skb(data);
if (!skb) {
recycle_data(data);
} else {
skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
...
}
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Tom Herbert <therbert@google.com>
CC: Jamal Hadi Salim <hadi@mojatatu.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Thomas Graf <tgraf@infradead.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.
The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Previously we claimed device ID 0x7450, regardless of the vendor, which is
clearly wrong. Now we'll claim that device ID only for AMD.
I suspect this was just a typo in the original code, but it's possible this
change will break shpchp on non-7450 AMD bridges. If so, we'll have to fix
them as we find them.
Reference: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=638863
Reported-by: Ralf Jung <ralfjung-e@gmx.de>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Windows driver .inf disables ASPM on hpsa devices. Do the same because the
selection of a non default ASPM policy can cause the device to hang.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ALC882 macpro and imac24 static configs can be transferred to the
auto-parser with the additional GPIO setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit [c3e837bb: ALSA: hda/realtek - Rewrite ALC882 acer-aspire-*
models with the auto-parser], the check of the model option got removed
mistakenly. Re-added the board_config check again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the pin or the DAC doesn't support the stereo, create a mono
control instead of creating a stereo control blindly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NR_BUILTIN_GPIO is both defined in arch-pxa and arch-mmp. Now replace it
with PXA_NR_BUILTIN_GPIO and MMP_NR_BUILTIN_GPIO.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use cpuid to recognize the gpio number and type. CPU_PXA26x is the
special case since we can't identify it by cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series,
others are linked to another interrupt line. All GPIO are linked to one
interrupt line in MMP series.
Since gpio driver is shared between PXA series and MMP series, define
GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code
from irq.c to gpio-pxa.c.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Avoid potential naming confliction since multiple architecture will be built
in a single kernel.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Commit ["62016250 lockdep: Add improved subclass caching"] tries to
improve performance (expecially to reduce the cost of rq->lock)
when using lockdep, but it fails due to lockdep_init_map() in
which ->class_cache is cleared. The typical caller is
lock_set_subclass(), after that class will not be cached anymore.
This patch tries to achive the goal of commit 62016250 by always
setting ->class_cache in register_lock_class().
=== Score comparison of benchmarks ===
for i in `seq 1 10`; do ./perf bench -f simple sched messaging; done
before: min: 0.604, max: 0.660, avg: 0.622
after: min: 0.414, max: 0.473, avg: 0.427
for i in `seq 1 10`; do ./perf bench -f simple sched messaging -g 40; done
before: min: 2.347, max: 2.421, avg: 2.391
after: min: 1.652, max: 1.699, avg: 1.671
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111109080714.GC8124@zhy
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Switch to local_irq_ ops so that the irq state is properly tracked
(raw_local_irq_* isn't tracked by lockdep, causing confusion).
Possible now that commit dd4e5d3ac4 ("lockdep: Fix
trace_[soft,hard]irqs_[on,off]() recursion") cured the reason we
needed the raw_ ops.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The raw_lock_irq_{save,restore}() already implies a
non-preemptibility.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
zap_locks() is used by printk() in a last ditch effort to get data
out, clearly we cannot trust lock state after this so make it disable
lock debugging.
Also don't treat printk recursion through lockdep as a normal
recursion bug but try hard to get the lockdep splat out.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-kqxwmo4xz37e1s8w0xopvr0q@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch solves the following problem:
Now some samples may be lost due to throttling. The number of samples is
restricted by sysctl_perf_event_sample_rate/HZ. A trace event is
divided on some samples according to event's period. I don't sure, that
we should generate more than one sample on each trace event. I think the
better way to use SAMPLE_PERIOD.
E.g.: I want to trace when a process sleeps. I created a process, which
sleeps for 1ms and for 4ms. perf got 100 events in both cases.
swapper 0 [000] 1141.371830: sched_stat_sleep: comm=foo pid=1801 delay=1386750 [ns]
swapper 0 [000] 1141.369444: sched_stat_sleep: comm=foo pid=1801 delay=4499585 [ns]
In the first case a kernel want to send 4499585 events and
in the second case it wants to send 1386750 events.
perf-reports shows that process sleeps in both places equal time. It's
bug.
With this patch kernel generates one event on each "sleep" and the time
slice is saved in the field "period". Perf knows how handle it.
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1320670457-2633428-3-git-send-email-avagin@openvz.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Split the callchain code from the perf events core into
a new kernel/events/callchain.c file.
This simplifies a bit the big core.c
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
[keep ctx recursion handling inline and use internal headers]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1318778104-17152-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It appears that stop_machine_text_poke() wants to be called on all CPUs,
like it's done from text_poke_smp(). Fix text_poke_smp_batch() to do
this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1319702072-32676-1-git-send-email-rabin@rab.in
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the core offcore support is fixed up (thanks Stephane) and we
have sane generic events utilizing them, re-enable the raw access to
the feature as well.
Note that it doesn't matter if you use event 0x1b7 or 0x1bb to specify
an offcore event, either one works and neither guarantees you'll end
up on a particular offcore MSR.
Based on original patch from: Vince Weaver <vweaver1@eecs.utk.edu>.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Vince Weaver <vweaver1@eecs.utk.edu>.
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1108031200390.703@cl320.eecs.utk.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
People (Linus) objected to using -ENOSPC to signal not having enough
resources on the PMU to satisfy the request. Use -EINVAL.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-xv8geaz2zpbjhlx0svmpp28n@git.kernel.org
[ merged to newer kernel, fixed up MIPS impact ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do not set task_ctx pointer during sched_in if there are no
events associated with the context. Otherwise if during task
execution total number of events in the system will become zero
perf_event_context_sched_out() will not be called and cpuctx->task_ctx
will be left with a stale value.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111023171033.GI17571@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Masami spotted that we always try to decode the instruction stream as
64bit instructions when running a 64bit kernel, this doesn't work for
ia32-compat proglets.
Use TIF_IA32 to detect if we need to use the 32bit instruction
decoder.
Reported-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In UP systems, the idle task is initialized using the init_task
structure from which the command name is taken (currently "swapper").
In SMP systems, one idle task per CPU is forked by the worker thread
from which the task structure is copied. The command name is, therefore,
"kworker/0:0" or "kworker/0:1", if not updated. Since such update was
lacking, all idle tasks in SMP systems were incorrectly named. This
longtime bug was not discovered immediately, because there is no /proc/0
entry - the bug only becomes apparent when tracing is enabled.
This patch sets the command name of the idle tasks in SMP systems to the
name that is used in the INIT_TASK structure suffixed by a slash and the
number of the CPU.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111026211708.768925506@osadl.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Normally the RT bandwidth scheme will share bandwidth across the
entire root_domain. However sometimes its convenient to disable this
sharing for debug purposes. Provide a simple feature switch to this
end.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The return-value convention for these functions varies depending on
whether they're interruptible or can timeout. It can be a little
confusing--document it.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111006192246.GB28026@fieldses.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>