BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent nohz scheduler changes, rq's nohz flag
'NOHZ_TICK_STOPPED' and its associated state doesn't get cleared
immediately after the cpu exits idle. This gets cleared as part
of the next tick seen on that cpu.
For the cpu offline support, we need to clear this state
manually. Fix it by registering a cpu notifier, which clears the
nohz idle load balance state for this rq explicitly during the
CPU_DYING notification.
There won't be any nohz updates for that cpu, after the
CPU_DYING notification. But lets be extra paranoid and skip
updating the nohz state in the select_nohz_load_balancer() if
the cpu is not in active state anymore.
Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-and-tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1327026538.16150.40.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 029632fbb7 ("sched: Make
separate sched*.c translation units") removed the include of
asm/mutex.h from sched.c.
This breaks the combination of:
CONFIG_MUTEX_SPIN_ON_OWNER=yes
CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX=yes
like s390 without mutex debugging:
CC kernel/sched/core.o
kernel/sched/core.c: In function ‘mutex_spin_on_owner’:
kernel/sched/core.c:3287: error: implicit declaration of function ‘arch_mutex_cpu_relax’
Lets re-add the include to kernel/sched/core.c
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1326268696-30904-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
KOSAKI Motohiro noticed the following race:
> CPU0 CPU1
> --------------------------------------------------------
> deactivate_task()
> task->state = TASK_UNINTERRUPTIBLE;
> activate_task()
> rq->nr_uninterruptible--;
>
> schedule()
> deactivate_task()
> rq->nr_uninterruptible++;
>
Kosaki-San's scenario is possible when CPU0 runs
__sched_setscheduler() against CPU1's current @task.
__sched_setscheduler() does a dequeue/enqueue in order to move
the task to its new queue (position) to reflect the newly provided
scheduling parameters. However it should be completely invariant to
nr_uninterruptible accounting, sched_setscheduler() doesn't affect
readyness to run, merely policy on when to run.
So convert the inappropriate activate/deactivate_task usage to
enqueue/dequeue_task, which avoids the nr_uninterruptible accounting.
Also convert the two other sites: __migrate_task() and
normalize_task() that still use activate/deactivate_task. These sites
aren't really a problem since __migrate_task() will only be called on
non-running task (and therefore are immume to the described problem)
and normalize_task() isn't ever used on regular systems.
Also remove the comments from activate/deactivate_task since they're
misleading at best.
Reported-by: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1327486224.2614.45.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In error cleanup of agp_backend_initialize() and in agp_backend_cleanup(),
agp_destroy_page() is passed virtual address of the scratch page. This
leads to a kernel warning if the initialization fails (or upon regular
cleanup) as pointer to struct page should be passed instead.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When a new net namespace is created, we should attach to it a "struct
net_generic" with enough slots (even empty), or we can hit the following
BUG_ON() :
[ 200.752016] kernel BUG at include/net/netns/generic.h:40!
...
[ 200.752016] [<ffffffff825c3cea>] ? get_cfcnfg+0x3a/0x180
[ 200.752016] [<ffffffff821cf0b0>] ? lockdep_rtnl_is_held+0x10/0x20
[ 200.752016] [<ffffffff825c41be>] caif_device_notify+0x2e/0x530
[ 200.752016] [<ffffffff810d61b7>] notifier_call_chain+0x67/0x110
[ 200.752016] [<ffffffff810d67c1>] raw_notifier_call_chain+0x11/0x20
[ 200.752016] [<ffffffff821bae82>] call_netdevice_notifiers+0x32/0x60
[ 200.752016] [<ffffffff821c2b26>] register_netdevice+0x196/0x300
[ 200.752016] [<ffffffff821c2ca9>] register_netdev+0x19/0x30
[ 200.752016] [<ffffffff81c1c67a>] loopback_net_init+0x4a/0xa0
[ 200.752016] [<ffffffff821b5e62>] ops_init+0x42/0x180
[ 200.752016] [<ffffffff821b600b>] setup_net+0x6b/0x100
[ 200.752016] [<ffffffff821b6466>] copy_net_ns+0x86/0x110
[ 200.752016] [<ffffffff810d5789>] create_new_namespaces+0xd9/0x190
net_alloc_generic() should take into account the maximum index into the
ptr array, as a subsystem might use net_generic() anytime.
This also reduces number of reallocations in net_assign_generic()
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sjur Brændeland <sjur.brandeland@stericsson.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (24 commits)
drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
drm/i915: debugfs: show semaphore registers also on gen7
drm/i915: allow userspace forcewake references also on gen7
drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
drm/i915: Correct debugfs printout for RC1e.
Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
drm/i915: rip out the HWSTAM missed irq workaround
drm/i915: paper over missed irq issues with force wake voodoo
drm/i915: Hold gt_lock across forcewake register reads
drm/i915: Hold gt_lock during reset
drm/i915: Move reset forcewake processing to gen6_do_reset
drm/i915: protect force_wake_(get|put) with the gt_lock
drm/i915: convert force_wake_get to func pointer in the gpu reset code
drm/i915: sprite init failure on pre-SNB is not a failure
drm/i915: VBT Parser cleanup for eDP block
drm/i915: mask transcoder select bits before setting them on LVDS
drm/i915: Add Clientron E830 to the ignore LVDS list
CHROMIUM: i915: Add DMI override to skip CRT initialization on ZGB
drm/i915: handle 3rd pipe
drm/i915: simplify pipe checking
...
The very same problem is seen on Haier W18 laptop with ALC861 as seen
on ASUS A6Rp, which was fixed by the commit 3b25eb69.
Now we just need to add a new SSID entry pointing to the same fixup.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42656
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is needed as otherwise we can get the following when
dealing with buggy data in a pinmux driver for
pinmux_search_function:
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
PC is at strcmp+0xc/0x34
LR is at pinmux_get+0x350/0x8f4
...
As we need pctldev initialized to call ops->list_functions,
let's initialize it before check_ops calls and pass the
pctldev to the check_ops functions. Do this for both pinmux
and pinconf check_ops functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ctrl_dev_name is optional for struct pinmux_map assuming
that ctrl_dev is set. Without this patch we can get:
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
(pinmux_hog_maps+0xa4/0x20c)
(pinctrl_register+0x2a4/0x378)
...
Fix this by adding adding a test for map->ctrl_dev.
Additionally move the test for map->ctrl_dev earlier
to optimize out the loop a bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some pinmux typos so implementing pinmux drivers
is a bit easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following build error found when building imx_v4_v5_defconfig:
CC arch/arm/mach-imx/mach-imx27ipcam.o
In file included from arch/arm/plat-mxc/include/mach/iomux-mx27.h:23,
from arch/arm/mach-imx/mach-imx27ipcam.c:22:
arch/arm/plat-mxc/include/mach/iomux-v1.h:99: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'imx_iomuxv1_init'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
That is the last one missing for those CPUs.
Others were recently added with commits
fb215366b3
(KVM: expose latest Intel cpu new features (BMI1/BMI2/FMA/AVX2) to guest)
and
commit 969df4b829
(x86: Report cpb and eff_freq_ro flags correctly)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/20120120163823.GC24508@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
apply_uV is errornously set when regulator is instantiated from device
tree, even when it doesn't contain any voltage constraints.
This commit fixes error:
machine_constraints_voltage: CHARGER: failed to apply 0uV constraint
for following regulator description in DTS:
CHARGER {
regulator-min-microamp = <100000>;
regulator-max-microamp = <200000>;
}
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize two spinlocks in tlb_uv.c and also properly define/initialize
the uv_irq_lock.
The lack of explicit initialization seems to be functionally
harmless, but it is diagnosed when these are turned on:
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_LOCKDEP=y
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/E1RnXd1-0003wU-PM@eag09.americas.sgi.com
[ Added the uv_irq_lock initialization fix by Dimitri Sivanich ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
uv_gpa_to_soc_phys_ram() was inadvertently ignoring the
shift values. This fix takes the shift into account.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120119020753.GA7228@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full. Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X. Set the module parameter log message accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make it more like how igb does it, with some additional error checking.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable RPS by default. Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.
v2: added ethtool command to query flow hashing behavior per Ben Hutchings
and changed the type of rsskey to cleanup the setting of the register
array and avoid unnecessary casts (as pointed out by Joe Perches).
The long error messages are not changed since there is nothing in
the kernel ./Documentation that suggests the preferred method for
dealing with long messages other than to never break strings; leaving
them as-is for now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
e1000_rx_checksum() instead of in each call to the function
v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous patch used the modulus operator over a power of 2
unnecessarily which may produce suboptimal binary code. This
patch changes changes them to binary ands instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Port autoselection finds a port and then drop the lock,
then right after that, gets the hash bucket again and lock it.
Fix it to go direct.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code checks for conflicts when the application
requests a specific port. If there is no conflict, then
the request is granted.
On the other hand, the port autoselection done by the kernel
fails when all ports are bound even when there is a port
with no conflict available.
The fix changes port autoselection to check if there is a
conflict and use it if not.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is received on an L2TP IP socket (L2TPv3 IP link
encapsulation), the l2tpip socket's backlog_rcv function calls
xfrm4_policy_check(). This is not necessary, since it was called
before the skb was added to the backlog. With CONFIG_NET_NS enabled,
xfrm4_policy_check() will oops if skb->dev is null, so this trivial
patch removes the call.
This bug has always been present, but only when CONFIG_NET_NS is
enabled does it cause problems. Most users are probably using UDP
encapsulation for L2TP, hence the problem has only recently
surfaced.
EIP: 0060:[<c12bb62b>] EFLAGS: 00210246 CPU: 0
EIP is at l2tp_ip_recvmsg+0xd4/0x2a7
EAX: 00000001 EBX: d77b5180 ECX: 00000000 EDX: 00200246
ESI: 00000000 EDI: d63cbd30 EBP: d63cbd18 ESP: d63cbcf4
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
[<c1218568>] sock_common_recvmsg+0x31/0x46
[<c1215c92>] __sock_recvmsg_nosec+0x45/0x4d
[<c12163a1>] __sock_recvmsg+0x31/0x3b
[<c1216828>] sock_recvmsg+0x96/0xab
[<c10b2693>] ? might_fault+0x47/0x81
[<c10b2693>] ? might_fault+0x47/0x81
[<c1167fd0>] ? _copy_from_user+0x31/0x115
[<c121e8c8>] ? copy_from_user+0x8/0xa
[<c121ebd6>] ? verify_iovec+0x3e/0x78
[<c1216604>] __sys_recvmsg+0x10a/0x1aa
[<c1216792>] ? sock_recvmsg+0x0/0xab
[<c105a99b>] ? __lock_acquire+0xbdf/0xbee
[<c12d5a99>] ? do_page_fault+0x193/0x375
[<c10d1200>] ? fcheck_files+0x9b/0xca
[<c10d1259>] ? fget_light+0x2a/0x9c
[<c1216bbb>] sys_recvmsg+0x2b/0x43
[<c1218145>] sys_socketcall+0x16d/0x1a5
[<c11679f0>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c100305f>] sysenter_do_call+0x12/0x38
Code: c6 05 8c ea a8 c1 01 e8 0c d4 d9 ff 85 f6 74 07 3e ff 86 80 00 00 00 b9 17 b6 2b c1 ba 01 00 00 00 b8 78 ed 48 c1 e8 23 f6 d9 ff <ff> 76 0c 68 28 e3 30 c1 68 2d 44 41 c1 e8 89 57 01 00 83 c4 0c
Signed-off-by: James Chapman <jchapman@katalix.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
