Fix the following build warning:
warning: (USB_HWA_HCD) selects UWB_HWA which has unmet direct dependencies (UWB && USB)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that when the transmit FIFO threshold is reached on OMAP
UARTs, it does not result in a PRCM wakeup. This appears to be a
silicon bug. This means that if the MPU powerdomain is in a low-power
state, the MPU will not be awakened to refill the FIFO until the next
interrupt from another device.
The best solution, at least for the short term, would be for the OMAP
serial driver to call a OMAP subarchitecture function to prevent the
MPU powerdomain from entering a low power state while the FIFO has
data to transmit. However, we no longer have a clean way to do this,
since patches that add platform_data function pointers have been
deprecated by the OMAP maintainer. So we attempt to work around this
as well. The workarounds depend on the setting of CONFIG_CPU_IDLE.
When CONFIG_CPU_IDLE=n, the driver will now only transmit one byte at
a time. This causes the transmit FIFO threshold interrupt to stay
active until there is no more data to be sent. Thus, the MPU
powerdomain stays on during transmits. Aside from that energy
consumption penalty, each transmitted byte results in a huge number of
UART interrupts -- about five per byte. This wastes CPU time and is
quite inefficient, but is probably the most expedient workaround in
this case.
When CONFIG_CPU_IDLE=y, there is a slightly more direct workaround:
the PM QoS constraint can be abused to keep the MPU powerdomain on.
This results in a normal number of interrupts, but, similar to the
above workaround, wastes power by preventing the MPU from entering
WFI.
Future patches are planned for the 3.4 merge window to implement more
efficient, but also more disruptive, workarounds to these problems.
DMA operation is unaffected by this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure FIFO levels are set correctly in non-DMA mode (the default).
This patch will cause a receive FIFO threshold interrupt to be raised when
there is at least one byte in the RX FIFO. It will also cause a transmit
FIFO threshold interrupt when there is only one byte remaining in the TX
FIFO.
These changes fix the receive interrupt problem and part of the
transmit interrupt problem. A separate set of issues must be worked
around for the transmit path to have a basic level of functionality; a
subsequent patch will address these.
DMA operation is unaffected by this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function serial_omap_restore_context is called only from
serial_omap_runtime_resume which depends on CONFIG_PM_RUNTIME. Make
serial_omap_restore_context also compile conditionally.
if CONFIG_PM_RUNTIME is not defined below warn may be seen.
LD net/xfrm/built-in.o
drivers/tty/serial/omap-serial.c:1524: warning: 'serial_omap_restore_context' defined but not used
CC drivers/tty/vt/selection.o
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The macro SET_SYSTEM_SLEEP_PM_OPS depends CONFIG_PM_SLEEP. The patch
defines the suspend and resume functions for CONFIG_PM_SLEEP instead of
CONFIG_SUSPEND.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rds_sock_info() triggers locking warnings because we try to perform a
local_bh_enable() (via sock_i_ino()) while hardware interrupts are
disabled (via taking rds_sock_lock).
There is no reason for rds_sock_lock to be a hardware IRQ disabling
lock, none of these access paths run in hardware interrupt context.
Therefore making it a BH disabling lock is safe and sufficient to
fix this bug.
Reported-by: Kumar Sanghvi <kumaras@chelsio.com>
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not cleaning up properly after unloading a pinmux
driver compiled as module.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After adding devpts multiple-insrances sysctl kernel.pty.max limit pty count for
each devpts instance independently, while kernel.pty.nr shows total pty count.
This patch restores sysctl kernel.pty.max as global limit (4096 by default),
adds pty reseve for main devpts (mounted without "newinstance" argument),
and new sysctl to tune it: kernel.pty.reserve (1024 by default)
Also it adds devpts mount option "max=%d" to limit pty count for each devpts
instance independently. (by default NR_UNIX98_PTY_MAX == 2^20)
Thus devpts instances in containers cannot eat up all available pty even if we didn't
set any limits, while with "max" argument we can adjust limits more precisely.
Plus, now open("/dev/ptmx") return -ENOSPC in case lack of pty indexes,
this is more informative than -EIO.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let's move this stuff to the better place, where we can account pty right in
tty-indexes managing code.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cleanup hack added in v2.6.27-3203-g15582d3
comment from that patch:
: pty: If the administrator creates a device for a ptmx slave we should not error
:
: The open path for ptmx slaves is via the ptmx device. Opening them any
: other way is not allowed. Vegard Nossum found that previously this was not
: the case and mknod foo c 128 42; cat foo would produce nasty diagnostics
:
: Signed-off-by: Alan Cox <alan@redhat.com>
: Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devpts_get_tty() returns non-null only for inodes on devpts, but there is no
inodes for master-devices, /dev/ptmx (/dev/pts/ptmx) is the only way to open them.
Thus we can completely forbid lookup for master-devices and eliminate that hack in
tty_init_dev() because tty_open() will get EIO from tty_driver_lookup_tty().
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intended to be able to support the current selection of the preferred
memcpy() implementation, this patch adds the ability to also measure the
two alternative implementations, again by way of using some
pre-processsor replacement.
While on my Westmere system this proves that the movsb based variant is
worse than the movsq based one (since the ERMS feature isn't there), it
also shows that here for the default as well as small sizes the unrolled
variant outperforms the movsq one.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4F16D728020000780006D732@nat28.tlf.novell.com
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since arch/x86/lib/memcpy_64.S implements not only __memcpy, but also
memcpy, without further precautions this function will get chose by the
static linker for resolving all references, and hence the "default"
measurement didn't really measure anything else than the
"x86-64-unrolled" one.
Fix this by renaming (through the pre-processor) the conflicting symbol.
On my Westmere system, the glibc variant turns out to require about 4%
less instructions, but 15% more cycles for the default 1Mb block size
measured.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4F16D6FD020000780006D72F@nat28.tlf.novell.com
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's better to not line break error messages to allow easier grepping
for them even when the line gets >80 chars. Additionally some minor
reformating is done.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new --uid command line option will show only the tasks for a given
user, using the proc interface to figure out the existing tasks.
Kernel work is needed to close races at startup, but this should already
be useful in many use cases.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-bdnspm000gw2l984a2t53o8z@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A considerable effort was invested in wiping out module.h
from being present in all the other standard includes. This
one leaked back in, but once again isn't strictly necessary,
so remove it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sa1111 socket driver oopses when removed:
Unable to handle kernel NULL pointer dereference at virtual address 000003b0
pgd = c1b40000
[000003b0] *pgd=00000000
Internal error: Oops: 41b43005 [#1]
Modules linked in:
CPU: 0 Not tainted (3.3.0-rc1+ #744)
PC is at pcmcia_remove+0x3c/0x60
LR is at pcmcia_remove+0x34/0x60
This is because we try to dereference a NULL 's' to obtain the next
pointer. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Corresponding changes to improve our error_state are pending
some other patches to clean up things first.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We need this to correctly access registers in the gt power well from
userspace.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We had two things in a row claiming to be RC6.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The file net/core/flow_dissector.c seems to be missing
including linux/export.h.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unnecessarily limits the number of offers we handle.
Get rid of this limitation. As part of this cleanup, also get rid of an
unused define - MAX_MSG_TYPES.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 74c2107759 (serial: Use block_til_ready helper) and its fixup
3f582b8c11 (serial: fix termios settings in open) introduced a
regression on UV systems. The serial eventually freezes while being
used. It's completely unpredictable and sometimes needs a heap of
traffic to happen first.
To reproduce this, yast installation was used as it turned out to be
pretty reliable in reproducing. Especially during installation process
where one doesn't have an SSH daemon running. And no monitor as the HW
is completely headless. So this was fun to find. Given the machine
doesn't boot on vanilla before 2.6.36 final. (And the commits above
are older.)
Unless there is some bad race in the code, the hardware seems to be
pretty broken. Otherwise pure MSR read should not cause such a bug,
or?
So to prevent the bug, revert to the old behavior. I.e. read modem
status only if we really have to -- for non-CLOCAL set serials.
Non-CLOCAL works on this hardware OK, I tried. See? I don't.
And document that shit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
References: https://lkml.org/lkml/2011/12/6/573
References: https://bugzilla.novell.com/show_bug.cgi?id=718518
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was an error on the jsm driver that would cause it to be unable to
recover after a second error is detected.
At the first error, the device recovers properly:
[72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0
[72521.485695] EEH: This PCI device has failed 1 times in the last hour:
...
[72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm
[72532.105689] jsm: Port 3 added
However, at the second error, it cascades until EEH disables the device:
[72631.229549] Call Trace:
...
[72641.725687] jsm: Port 3 added
[72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0
[72641.725698] EEH: This PCI device has failed 3 times in the last hour:
It was caused because the PCI state was not being saved after the first
restore. Therefore, at the second recovery the PCI state would not be
restored.
Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman is the current TTY maintainer, however he wouldn't appear
listed as such upon running get_maintainers.pl for drivers under
drivers/tty/serial.
Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insert ddebug_exec_queries() in place of ddebug_exec_query(). It
splits the query string on [;\n], and calls ddebug_exec_query() on
each. All queries are processed independent of errors, allowing a
query to fail, for example when a module is not installed. Empty
lines and comments are skipped. Errors are counted, and the last
error seen (negative) or the number of callsites found (0 or positive)
is returned. Return code checks are altered accordingly.
With this, multiple queries can be given in ddebug_query, allowing
more selective enabling of callsites. As a side effect, a set of
commands can be batched in:
cat cmd-file > $DBGMT/dynamic_debug/control
We dont want a ddebug_query syntax error to kill the dynamic debug
facility, so dynamic_debug_init() zeros ddebug_exec_queries()'s return
code after logging the appropriate message, so that ddebug tables are
preserved and $DBGMT/dynamic_debug/control file is created. This
would be appropriate even without accepting multiple queries.
This patch also alters ddebug_change() to return number of callsites
matched (which typically is the same as number of callsites changed).
ddebug_exec_query() also returns the number found, or a negative value
if theres a parse error on the query.
Splitting on [;\n] prevents their use in format-specs, but selecting
callsites on punctuation is brittle anyway, meaningful and selective
substrings are more typical.
Note: splitting queries on ';' before handling trailing #comments
means that a ';' also terminates a comment, and text after the ';' is
treated as another query. This trailing query will almost certainly
result in a parse error and thus have no effect other than the error
message. The double corner case with unexpected results is:
ddebug_query="func foo +p # enable foo ; +p"
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Factor pr_info(query) out of ddebug_parse_query, into vpr_info_dq(),
for reuse later. Also change the printed labels: file, func to agree
with the query-spec keywords accepted in the control file. Pass ""
when string is null, to avoid "(null)" output from sprintf. For
format print, use precision to skip last char, assuming its '\n', no
great harm if not, its a debug msg.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
trim_prefix(path) skips past the absolute source path root, and
returns the pointer to the relative path from there. It is used to
shorten the displayed path in $DBGMT/dynamic_debug/control via
ddebug_proc_show(), and in ddebug_change() to allow relative filenames
to be used in applied queries. For example:
~# echo file kernel/freezer.c +p > $DBGMT/dynamic_debug/control
kernel/freezer.c:128 [freezer]cancel_freezing p " clean up: %s\012"
trim_prefix(path) insures common prefix before trimming it, so
out-of-tree module paths are shown as full absolute paths.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current query write buffer is 256 bytes, on stack. In comparison, the
ddebug_query boot-arg is 1024. Allocate the buffer off heap, and
enlarge it to 4096 bytes, big enough for ~100 queries (at 40 bytes
each), and error out if not. This makes it play nicely with large
query sets (to be added later). The buffer should be enough for most
uses, and others should probably be split into subsets.
[jbaron@redhat.com: changed USER_BUF_PAGE from 4095 -> 4096 ]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a token begins with #, the remainder of query string is a comment,
so drop it. Doing it here avoids '#' in quoted strings.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lineno:24 allows files with 4 million lines, an insane file-size, even
for never-to-get-in-tree machine generated code. Reduce this to 18
bits, which still allows 256k lines. This is still insanely big, but
its not raving mad.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If _ddebug table is empty (in a CONFIG_DYNAMIC_DEBUG build this
shouldn't happen), then warn (error?) and return early. This skips
empty table scan and parsing of setup-string, including the pr_info
call noting the parse. By inspection, copy return-code handling from
1st ddebug_add_module() callsite to 2nd.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Issue error when a match-spec is given multiple times in a rule.
Previous code kept last one, but was silent about it. Docs imply only
one is allowed by saying match-specs are ANDed together, given that
module M cannot match both A and B. Also error when last_line < 1st_line.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change describe_flags() to emit '=[pmflt_]+' for current callsite
flags, or just '=_' when they're disabled. Having '=' in output
allows a more selective grep expression; in contrast '-' may appear
in filenames, line-ranges, and format-strings. '=' also has better
mnemonics, saying; "the current setting is equal to <flags>".
This allows grep "=_" <dbgfs>/dynamic_debug/control to see disabled
callsites while avoiding the many occurrences of " = " seen in format
strings.
Enlarge flagsbufs to handle additional flag char, and alter
ddebug_parse_flags() to allow flags=0, so that user can turn off all
debug flags via:
~# echo =_ > <dbgfs>/dynamic_debug/control
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
do_set_multicast() may not free the memory malloc in
netvsc_set_multicast_list().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace strcpy with strlcpy, and add define for the size constant.
[jbaron@redhat.com: Use DDEBUG_STRING_SIZE for overflow check]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow changing dynamic_debug verbosity at run-time, to ease debugging
of ddebug queries as you add them, improving usability.
at boot time: dynamic_debug.verbose=1
at runtime:
root@voyage:~# echo 1 > /sys/module/dynamic_debug/parameters/verbose
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If CONFIG_DYNAMIC_DEBUG is defined, honor it over DEBUG, so that
pr_debug()s are controllable, instead of always-on. When DEBUG is
also defined, change _DPRINTK_FLAGS_DEFAULT to enable printing by
default.
Also adding _DPRINTK_FLAGS_INCL_MODNAME would be nice, but there are
numerous cases of pr_debug(NAME ": ...), which would result in double
printing of module-name. So defer this until things settle.
Cc: David Miller <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently any enabled dynamic-debug flag on a pr_debug callsite will
enable printing, even if _DPRINTK_FLAGS_PRINT is off. Checking print
flag directly allows "-p" to disable callsites without fussing with
other flags, so the following disables everything, without altering
flags user may have set:
echo -p > $DBGFS/dynamic_debug/control
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An implicit instance of module.h leaked back into existence
and was masking the fact that these drivers weren't calling
out the include for itself. Fix the drivers before we remove
the implicit include path via net/netprio_cgroup.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STM has a device ID within its own VENDOR space, and it is being
used in the STA2X11 I/O Hub.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tracking the number of subdirectories requires an extra field that increases
the size of sysfs_dirent. nlinks are not particularly interesting for sysfs
and the nlink counts are wrong when network namespaces are involved so stop
counting them, and always return nlink == 1. Userspace already knows that
directories with nlink == 1 have an nlink count they can't use to count
subdirectories.
This reduces the size of sysfs_dirent by 8 bytes on 64bit platforms.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Store the sysfs inode number in an unsided int because
ida inode allocator can return at most a 31 bit number,
reducing the size of struct sysfs_dirent by 8 bytes
on 64bit platforms.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
