"group" is the group where the backup will be placed, and is
initialized to zero in the declaration. This meant that backups for
meta_bg descriptors were erroneously written to the backup block group
descriptors in groups 1 and (desc_per_block-1).
Reproduction information:
mke2fs -Fq -t ext4 -b 1024 -O ^resize_inode /tmp/foo.img 16G
truncate -s 24G /tmp/foo.img
losetup /dev/loop0 /tmp/foo.img
mount /dev/loop0 /mnt
resize2fs /dev/loop0
umount /dev/loop0
dd if=/dev/zero of=/dev/loop0 bs=1024 count=2
e2fsck -fy /dev/loop0
losetup -d /dev/loop0
Signed-off-by: Andy Leiserson <andy@leiserson.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
The commonly accepted wisdom that scheduling work on the same cpu
that handled interrupt i/o benefits from cache-locality is only
true if the cpu is idle (since bound kworkers are often the highest
vruntime and thus the lowest priority).
Measurements of scheduling via the unbound queue show lowered
worst-case latency responses of up to 5x over bound workqueue, without
increase in average latency or throughput.
pty i/o test measurements show >3x (!) reduced total running time; tests
previously taking ~8s now complete in <2.5s.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce API functions to restart and cancel tty buffer work, rather
than manipulate buffer work directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_write_message() allows the caller to directly write to a specific
tty. Since the line discipline is bypassed for the direct write,
nothing prevents the tty from being torn down after the tty count is
checked.
Hold the tty lock for the duration of the direct write.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tiocspgrp() is the ioctl handler for TIOCSPGRP, which runs in
non-atomic context; use spin_lock/unlock_irq (since interrupt state
is on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The job_control() check in n_tty_read() has nearly identical purpose
and results as tty_check_change(). Both functions' purpose is to
determine if the current task's pgrp is the foreground pgrp for the tty,
and if not, to signal the current pgrp.
Introduce __tty_check_change() which takes the signal to send
and performs the shared operations for job control() and
tty_check_change().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_DUMMY_DR_RX status bit is equal to (1 << 16), so a u16 is too small
to hold that value. The result is that UART_DUMMY_DR_RX is never passed
to uart_insert_char(). This means that we're always accepting characters,
even when CREAD (in termios) is not set.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0fd972a7d9 (module: relocate module_init from init.h to
module.h) broke the build of ttyFDC driver due to that driver's (mis)use
of module_mips_cdmm_driver() without first including module.h, for
example:
In file included from ./arch/mips/include/asm/cdmm.h +11 :0,
from drivers/tty/mips_ejtag_fdc.c +34 :
include/linux/device.h +1295 :1: warning: data definition has no type or storage class
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
include/linux/device.h +1295 :1: error: type defaults to ‘int’ in declaration of ‘module_init’ [-Werror=implicit-int]
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: warning: parameter names (without types) in function declaration
Instead of just adding the module.h include, switch to using the new
builtin_mips_cdmm_driver() helper macro and drop the remove callback,
since it isn't needed. If module support is added later, the code can
always be resurrected.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.2.x-
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9119fba0cf.
This commit prevents from sending "big" file using Bluetooth.
When sending a lot of data quickly through the Bluetooth interface, and
after a variable amount of data sent, transfer fails with error:
kernel: [ 415.247453] Bluetooth: hci0 hardware error 0x00
Found on T100TA.
After reverting this commit, send works fine for any file size.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Fixes: 9119fba0cf (serial: 8250_dma: don't bother DMA with small transfers)
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platforms that have this UART, but that don't have
separate PCI device for the DMA Engine, need to create the
HSU DMA Engine device separately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no platforms where it's not possible to calculate
the number of channels based on IO space length, and since
that is the only purpose for struct hsu_dma_platform_data,
removing it.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows UART drivers to register HSU DMA Engine without
being forced to use ifdefs.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSU (High Speed UART) DMA engine, like the name suggests, is
an integrated DMA engine for UART and UART alone. Therefore,
making the UART drivers responsible of selecting it and
removing the user selectable option for it. The UARTs with
this DMA engine can always select HSU_DMA when
SERIAL_8250_DMA option is enabled.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent patch to create common helper functions for modem control
lines created empty helper functions in a header file, but accidentally
did not mark them as 'static inline', which causes build errors:
drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_enable_ms':
mxs-auart.c:(.text+0x171c): multiple definition of `mctrl_gpio_enable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x768): first defined here
drivers/tty/serial/mxs-auart.o: In function `mctrl_gpio_disable_ms':
mxs-auart.c:(.text+0x1720): multiple definition of `mctrl_gpio_disable_ms'
drivers/tty/serial/clps711x.o:clps711x.c:(.text+0x76c): first defined here
This adds the missing annotation, so the functions do not get placed
in each object file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ce59e48fdb ("serial: mctrl_gpio: implement interrupt handling")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel MID UART quirks require already quite a bit of code
in 8250_pci.c. On new Intel platforms where it is used, the
integrated DMA engine no longer has its own PCI device, but
is instead configured from the UART's MMIO. That means we
will have to add even more code for handling just MID UARTs.
Instead of adding that to 8250_pci.c, splitting the support
of Intel MID UART into its own driver. Handling of the
integrated DMA engine becomes much simpler this way. Own
driver will also remove the need for things like specific
set_termios hooks for every board using this UART, and
simplify the handling of it in general.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT and command line based earlycon support for
lpuart and lpuart32 used on Freescale Vybrid and and QorIQ LS1021A
processors.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently got rid of some modular code in this driver and also
got rid of the unused ".remove" function at the same time. Thierry
noted that it was however possible to force the remove through the
bind/unbind interface.
Since this is a console device used on 2005 vintage 74xx based
powerpc embedded targets, and is essentially always used in
conjunction with SERIAL_MPSC_CONSOLE=y -- there is no sane reason
anyone would ever want to unbind the builtin driver and lose the
console. So we just explicitly block bind/unbind operations and
prevent root from shooting themselves in the foot.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waking the reader immediately upon receipt of TTY_BREAK or TTY_PARITY
chars has no effect on the outcome of read():
1. Only non-canonical/EXTPROC mode applies since canonical mode
will not return data until a line termination is received anyway
2. EXTPROC mode - the reader will always be woken by the input worker
3. Non-canonical modes
a. MIN == 0, TIME == 0
b. MIN == 0, TIME > 0
c. MIN > 0, TIME > 0
minimum_to_wake is always 1 in these modes so the reader will always
be woken by the input worker
d. MIN > 0, TIME == 0
although the reader will not be woken by the input worker unless the
minimum data is received, the reader would not otherwise have
returned the received data
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The statement after if should be indenteted. So fix this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a misplaced bracket in atmel_init_rs485 which sets
rs485-rx-during-tx and rs485-enabled-at-boot-time only if
rs485-rts-delay is set in of.
This is clearly a bug, so fix it by moving the bracket to the proper
place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In-tree users of wait_event_interruptible_tty() have been removed;
remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty lock is strictly for serializing tty lifetime events
(open/close/hangup), and not for line discipline serialization.
The tty core already provides serialization of concurrent writes
to the same tty, and line discipline lifetime management (by ldisc
references), so pinning the tty via tty_lock() is unnecessary and
counter-productive; remove tty lock use.
However, the line discipline is responsible for serializing reads
(if required by the line discipline); add read_lock mutex to
serialize calls of r3964_read().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core provides read_wait waitqueue specifically for line
disciplines to wait readers; otherwise, the line discipline may
miss wakeups generated by the tty core.
NB: The tty core already provides serialization for the line discipline's
close() method, and guarantees no readers or writers will be using the
closing instance of the line discipline. Completely remove that wakeup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the removal of tty_wait_until_sent_from_close(), tty drivers
no longer wait during open for parallel closes to complete (instead,
the tty core waits before calling the driver open() method). Thus,
the close_wait waitqueue is no longer used for waiting.
Remove struct tty_port::close_wait.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since at least before 2.6.30, tty drivers that do not drop the tty lock
while closing cannot observe ASYNC_CLOSING set while holding the
tty lock; this includes the tty driver's open() and hangup() methods,
since the tty core calls these methods holding the tty lock.
For these drivers, waiting for ASYNC_CLOSING to clear while opening
is not required, since this condition cannot occur. Similarly, even
when the open() method drops and reacquires the tty lock after
blocking, ASYNC_CLOSING cannot be set (again, for drivers that
do not drop the tty lock while closing).
Now that tty port drivers no longer drop the tty lock while closing
(since 'tty: Remove tty_wait_until_sent_from_close()'), the same
conditions apply: waiting for ASYNC_CLOSING to clear while opening
is not required, nor is re-checking ASYNC_CLOSING after dropping and
reacquiring the tty lock while blocking (eg., in *_block_til_ready()).
Note: The ASYNC_CLOSING flag state is still maintained since several
bitrotting drivers use it for (dubious) other purposes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_wait_until_sent_from_close() drops the tty lock while waiting
for the tty driver to finish sending previously accepted data (ie.,
data remaining in its write buffer and transmit fifo).
tty_wait_until_sent_from_close() was added by commit a57a7bf3fc
("TTY: define tty_wait_until_sent_from_close") to prevent the entire
tty subsystem from being unable to open new ttys while waiting for
one tty to close while output drained.
However, since commit 0911261d4c ("tty: Don't take tty_mutex for tty
count changes"), holding a tty lock while closing does not prevent other
ttys from being opened/closed/hung up, but only prevents lifetime event
changes for the tty under lock.
Holding the tty lock while waiting for output to drain does prevent
parallel non-blocking opens (O_NONBLOCK) from advancing or returning
while the tty lock is held. However, all parallel opens _already_
block even if the tty lock is dropped while closing and the parallel
open advances. Blocking in open has been in mainline since at least 2.6.29
(see tty_port_block_til_ready(); note the test for O_NONBLOCK is _after_
the wait while ASYNC_CLOSING).
IOW, before this patch a non-blocking open will sleep anyway for the
_entire_ duration of a parallel hardware shutdown, and when it wakes, the
error return will cause a release of its tty, and it will restart with
a fresh attempt to open. Similarly with a blocking open that is already
waiting; when it's woken, the hardware shutdown has already completed
to ASYNC_INITIALIZED is not set, which forces a release and restart as
well.
So, holding the tty lock across the _entire_ close (which is what this
patch does), even while waiting for output to drain, is equivalent to
the current outcome wrt parallel opens.
Cc: Alan Cox <alan@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the tegra UART driver there are three places where the RX DMA buffer
is handled and pushed up to the tty layer. In all three instances the
same functions are called and so instead of duplicating the code in three
places, move this code to a new helper function and use this new function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial-tegra driver always uses DMA and hence the driver always
allocates DMA channels. Therefore, the test to see if the RX DMA channel
is initialised in tegra_uart_stop_rx() is unnecessary and so remove
the test and the code that corresponds to the case where the RX DMA
channel is not initialised. Please note that the call to
tegra_uart_stop_rx() should always be before the call to
tegra_uart_shutdown() which will uninitialise the RX DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions in the serial-tegra driver have unnecessary return
statements at the end of a void function and so remove them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 853a699739 ("serial: tegra: handle race condition on uart rx
side") attempted to fix a race condition between the RX end of
transmission interrupt and RX DMA completion callback. Despite this
fix there is still another case where these two paths can race and
result in duplicated data. The race condition is as follows:
1. DMA completion interrupt occurs and schedules tasklet to call DMA
callback.
2. DMA callback for the UART driver starts to execute. This will copy
the data from the DMA buffer and restart the DMA. This is done under
uart port spinlock.
3. During the callback, UART interrupt is raised for end of receive. The
UART ISR runs and waits to acquire port spinlock held by the DMA
callback.
4. DMA callback gives up spinlock after copying the data, but before
restarting DMA.
5. UART ISR acquires the spin lock and reads the same DMA buffer because
DMA has not been restarted yet.
The release of the spinlock during the DMA callback was introduced by
commit 9b88748b36 ("tty: serial: tegra: drop uart_port->lock before
calling tty_flip_buffer_push()") to fix a spinlock lock-up issue when
calling tty_flip_buffer_push(). However, since then commit a9c3f68f3c
("tty: Fix low_latency BUG") migrated tty_flip_buffer_push() to always
use a workqueue, allowing tty_flip_buffer_push() to be called from
within atomic sections. Therefore, we can remove the unlocking of the
spinlock from the DMA callback and UART ISR and this will ensure that
the race condition no longer occurs.
Reported-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing UART_MCR_RTS or UART_MCR_XONANY is unnecessary; these bits
are never set in the shadow mcr. The RTS clear is especially confusing.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same serial hardware is present on LS2080A which is arm64, and
LS1021A which is arm32, so don't limit the workaround to PPC.
Unlike PPC which uses arch/powerpc/kernel/legacy_serial.c, the ARM
targets use drivers/tty/serial/of_serial.c, so add the handle_irq
override check there as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to hardcode the MEN_Z135_MEM_SIZE. The MCB subsystem
already knowns the size which is located in the chameleon table.
MCB parse the chameleon table to get the resources of each IP and provide
the mcb_request_mem function to get those resources.
Use mcb_request_mem to get the resources. This function also takes care of
the memory region naming allocated by the driver for each of the instances.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning on KVM and LPAE support on top of a multi_v7_defconfig will
produce a compiler warning in the Atmel serial driver:
drivers/tty/serial/atmel_serial.c: In function 'atmel_verify_port':
drivers/tty/serial/atmel_serial.c:2299:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
if ((void *)port->mapbase != ser->iomem_base)
^
Fix that by using the cast on the right hand side instead, as similar
code already does in other drivers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_enter_critical_mutex() is a simple call to mutex_lock_interruptible(),
but there is no error handling code for it.
The patch removes wrapper _enter_critical_mutex() and
adds error handling for mutex_lock_interruptible().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cvm_oct_xaui_open() is trivial and does not need a dedicated file.
Move it to the main file.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop redundant poll_now parameter from cvm_oct_common_open.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get the initial link status already on open instead of postponing
it to the periodic poll task. This unifies the behaviour with
other interfaces types.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the same portal is used to call mc_send_command() from two
different threads or a thread and an interrupt handler, serialization
is required, as the MC only supports one outstanding command per MC
portal. Thus, a new command should not be sent to the MC until the
last command sent has been responded by the MC.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactored mc_send_command() to support two flavors of polling:
- preemptible (for non-atomic portals), which was already supported.
It calls usleep_range() between polling iterations.
- non-preemptible (for atomic portals), which is needed when
mc_send_command() is called with interrupts disabled.
It calls udelay() between polling iterations.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moved wait logic in mc_send_command() to its own function
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changed units for the timeout to wait for completion
of MC command, from jiffies to milliseconds.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
owner needs to be initialized as THIS_MOUDLE.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initializing the object attributes for the root dprc, the
irq_count was uninitialized. Initialize it to 1.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check that resource is not NULL before de-referencing it.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaced error gotos with direct returns in fsl_mc_allocator_probe()
and fsl_mc_allocator_remove(), since the only error handling done
in those functions is to exit.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
