With the removal of 31 bit support a couple of defines became unused.
Remove them.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For some unknown reason the mcck_interruption_code field is defined
as array of two 32 bit values. Given that this actually is a 64 bit
field according to the architecture, change the type to u64.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The defines that are used in entry.S have been partially converted to
use the _BITUL macro (setup.h). This patch converts the rest.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu flags and pt_regs flags fields are each 64 bits in size. A flag can
be set with helper functions like set_cpu_flags().
These functions create a mask using "1U << flag". This doesn't work if flag
is larger than 31, since 1U << 32 == 0.
So fix this in case we ever will have such flag numbers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When using systemtap it was observed that our udelay implementation is
rather suboptimal if being called from a kprobe handler installed by
systemtap.
The problem observed when a kprobe was installed on lock_acquired().
When the probe was hit the kprobe handler did call udelay, which set
up an (internal) timer and reenabled interrupts (only the clock comparator
interrupt) and waited for the interrupt.
This is an optimization to avoid that the cpu is busy looping while waiting
that enough time passes. The problem is that the interrupt handler still
does call irq_enter()/irq_exit() which then again can lead to a deadlock,
since some accounting functions may take locks as well.
If one of these locks is the same, which caused lock_acquired() to be
called, we have a nice deadlock.
This patch reworks the udelay code for the interrupts disabled case to
immediately leave the low level interrupt handler when the clock
comparator interrupt happens. That way no C code is being called and the
deadlock cannot happen anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sparse does not understand the s390 specific hotpatch attribute and
floods the log with messages like
include/uapi/linux/swab.h:92:8: error: attribute 'hotpatch': unknown attribute
Let's just dont use it, if __CHECKER__ is defined.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The program parameter can be used to mark hardware samples with
some token. Previously, it was used to mark guest samples only.
Improve the program parameter doubleword by combining two parts,
the leftmost LPP part and the rightmost PID part. Set the PID
part for processes by using the task PID.
To distinguish host and guest samples for the kernel (PID part
is zero), the guest must always set the program paramater to a
non-zero value. Use the leftmost bit in the LPP part of the
program parameter to be able to detect guest kernel samples.
[brueckner@linux.vnet.ibm.com]: Split __LC_CURRENT and introduced
__LC_LPP. Corrected __LC_CURRENT users and adjusted assembler parts.
And updated the commit message accordingly.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The use of OFFSET instead of DEFINE makes the definitions in asm-offsets.c
more readable. While we are at it sort the defines for struct _lowcore
according to the field order and remove some unneeded defines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sclp console and tty code currently uses several message text
objects in a single message event to print several lines with one
SCCB. This causes the output of these lines to be fused into a
block which is noticeable when selecting text in the operating system
message panel.
Instead use several message events with a single message text object
each to print every line on its own. This changes the SCCB layout
from
struct sccb_header
struct evbuf_header
struct mdb_header
struct go
struct mto
...
struct mto
to
struct sccb_header
struct evbuf_header
struct mdb_header
struct go
struct mto
...
struct evbuf_header
struct mdb_header
struct go
struct mto
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Various functions in entry.S perform test-under-mask instructions
to test for particular bits in memory. Because test-under-mask uses
a mask value of one byte, the mask value and the offset into the
memory must be calculated manually. This easily introduces errors
and is hard to review and read.
Introduce the TSTMSK assembler macro to specify a mask constant and
let the macro calculate the offset and the byte mask to generate a
test-under-mask instruction. The benefit is that existing symbolic
constants can now be used for tests. Also the macro checks for
zero mask values and mask values that consist of multiple bytes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previously, the init task did not have an allocated FPU save area and
saving an FPU state was not possible. Now if the vector extension is
always enabled, provide a static FPU save area to save FPU states of
vector instructions that can be executed quite early.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the kernel detects that the s390 hardware supports the vector
facility, it is enabled by default at an early stage. To force
it off, use the novx kernel parameter. Note that there is a small
time window, where the vector facility is enabled before it is
forced to be off.
With enabling the vector facility by default, the FPU save and
restore functions can be improved. They do not longer require
to manage expensive control register updates to enable or disable
the vector enablement control for particular processes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The call to pgste_set_key in ptep_set_access_flags can be avoided
if the old pte is found to be valid at the time the new access
rights are set. The function that created the old, valid pte already
completed the required storage key operation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The principles of operation states reads are in order, writes are in
order, writes can be reordered after reads, but no reads can be
reordered after writes.
The atomic and bitops variantes for z196 use the interlocked-access
facility instructions with a memory barrier before and after the
instruction. Because of the memory ordering the first barrier is
unnecessary and can be removed.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To be able to analyse problems in regard to hypervisor overhead
add a tracepoing for diagnose calls. It reports the number of
the diagnose issued, e.g.
sshd-1385 [002] .... 42.701431: diagnose: nr=0x9c
<idle>-0 [001] ..s. 43.587528: diagnose: nr=0x9c
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce /sys/debug/kernel/diag_stat with a statistic how many diagnose
calls have been done by each CPU in the system.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The generic implementation for test_and_set_bit_lock in include/asm-generic
uses the standard test_and_set_bit operation. This is done with either a
'csg' or a 'loag' instruction. For both version the cache line is fetched
exclusively, even if the bit is already set. The result is an increase in
cache traffic, for a contented lock this is a bad idea.
Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use bit 2**1 of the pte and bit 2**14 of the pmd for the soft dirty
bit. The fault mechanism to do dirty tracking is already in place.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are primitives to create and query the software dirty bits
in a pte or pmd. But the clearing of the software dirty bits is done
in common code with x86 specific page table functions.
Add the missing architecture primitives to clear the software dirty
bits to allow the feature to be used on non-x86 systems, e.g. the
s390 architecture.
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We often need to correlate an 8 bit path mask with the position
in a channel path array. Introduce and use pathmask_to_pos for
that task.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
During resume from hibernate we already reenable measurement block
updates on a per device basis. In addition to that we also need to
activate channel measurement globally using the set channel monitor
instruction.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extended measurement blocks need to be 64 byte aligned. To achieve that
128 bytes for each measurement block are allocated and an align callback
returns a 64 byte aligned address inside this area.
Replace this code with kmem_cache allocations.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The measurement block for the extended measurement data is not freed when
switching off per device measurement. Free the measurement block after HW
stopped accessing it.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
During allocation of extended measurement blocks we check if the device is
already active for channel measurement and add the device to a list of
devices with active channel measurement. The check is done under ccwlock
protection and the list modification is guarded by a different lock.
To guarantee that both states are in sync make sure that both locks
are held during the allocation process (like it's already done for the
"normal" measurement block allocation).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices with active channel measurement are included in a list. When a
device is removed without deactivating channel measurement first the
list_head is freed but still used. Fix this by making sure that
channel measurement is deactivated during device deregistration.
For devices that we deregister because they are no longer accessible
deactivating channel measurement will fail. In this case we can report
success because the FW will no longer access the measurement block.
In addition to these steps keep an extra device reference while
channel measurement is active.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hold the device_lock during [de]activation of the channel measurement
block to synchronize concurrent usage of these functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that we hold the ccwlock when accessing private data. Return errors
that occur during measurement enabling to userspace. Apply some cleanups
while at it.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The <linux/memblock.h> already provides for_each_mem_range() macro that
iterates through memblock areas from type_a and not included in type_b.
We can remove custom for_each_dump_mem_range() macro and use the
for_each_mem_range() instead.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The principles of operation says:
The storage-operand fetch references of one instruction
occur after those of all preceding instructions and
before those of subsequent instructions, as observed
by other CPUs and by channel programs.
[...]
The CPU may fetch the operands of instructions before the
instructions are executed.
[...]
The CPU may delay placing results in storage.
[...]
the results of one instruction are placed in storage after
the results of all preceding instructions have been placed
in storage and before any results of the succeeding
instructions are stored, as observed by other CPUs and by
the channel subsystem.
which boils down to:
- reads are in order
- writes are in order
- reads can happen earlier
- writes can happen later
By definition (see memory-barrier.txt) read barriers orders
reads vs reads and write barriers orders writes agains writes.
but neither of these orders reads vs. writes.
That means we can implement smp_wmb,smp_rmb,wmb and rmb as
simple compiler barriers. To avoid reviewing all driver code
for correct barrier usage we keep dma_[rw]mb as serialization
for now.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
By definition smp_wmb only orders writes against writes. (Finish all
previous writes, and do not start any future write). To protect the
vdso init code against early reads on other CPUs, let's use a full
smp_mb at the end of vdso init. As right now smp_wmb is implemented
as full serialization, this needs no stable backport, but this change
will be necessary if we reimplement smp_wmb.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
_raw_write_lock_wait first sets the high order bit to indicate a
pending writer and then waits for the reader to drop to zero.
smp_rmb by definition only orders reads against reads. Let's use
a full smp_mb instead. As right now smp_rmb is implemented
as full serialization, this needs no stable backport, but this
patch will be necessary if we reimplement smp_rmb.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We were able to reduce the CPU overhead of big paging scenarios
when announcing our paging disks as non-rotational.
Almost all dasd devices are implemented in storage servers with
cache, raid, striping and lots of magic. There is no point in
optimizing the disk schedulers and swap code for a single platter
moving arm rotational disks. Given the complexity of the setup
and the fact that this change is mostly to disable the additional
overhead in swap code, lets keep the other functionality unchanged
and do not disable the this device as entropy source - unlike other
non-rotational devices.
Suggested-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the past only even modulus sizes were allowed for RSA keys in
CRT format. This restriction was based on limited RSA key generation
on older crypto adapters that provides only even modulus sizes. This
restriction is not valid any more.
Revoke restrictions that crypto requests can be serviced with odd
RSA modulus length in CRT format.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ra_list cannot be NULL here, so remove the unnecessary NULL check.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ndo_validate_addr is set to generic eth_validate_addr() function
used for MAC address validation.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Even if hostapd configuration file contains VHT parameters,
they were not getting reflected in beacons. The reason is
we are resetting them before starting AP. This patch removes
redundant BSS_STOP and SYS_RESET firmware commands before
starting AP to fix the problem.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When device_register() fails, kfree() is called in hsi_client_release(),
hence there is no need to call kfree in err3 again.
Fixes: a2aa24734d ("HSI: Add common DT binding for HSI client devices")
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
By default our chip will be in spatial coexistence mode.
This patch adds a provision to change it to timeshare mode
via debugfs command.
Enable timeshare coexistence mode
echo 1 > /sys/kernel/debug/mwifiex/mlan0/timeshare_coex
Go back to spacial coexistence mode
echo 0 > /sys/kernel/debug/mwifiex/mlan0/timeshare_coex
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Just fix a typo in the code comment.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A small bugfix for commit ede6a5e7b8 ("ath9k: Add QCA956x HW support").
I guess I would have skipped renaming (that initial QCA956x commit has
been there already for almost a year with the "5g" in the name) and move
the call outside AR_SREV_9462_20_OR_LATER() to make it reachable.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rename the variable as preparation for using the array with 2.4 GHz
band, etc.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver was reporting 'switch case not processed' after association,
so HW_VAR_KEEP_ALIVE was added and filled similarily to other drivers.
Positive side effect to this seems to be a bit more stable connection.
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For 8897 chipset, mwifiex_usb unnecessarily used to
come into picture when wlan is supposed to be used
via PCIe interface and USB interface is for
bluetooth.
This problem has been resolved for newer chipset by
having separate USB product ids for USB-USB8997 and
PCIe-USB8997 chipset variants. This patch ensures to
use wlan specific product id.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't have any customer using this chipset via USB
interface. if both mwifiex_pcie and mwifiex_usb modules
are enabled by user, sometimes mwifiex_usb wins the race
even if user wants wlan interface to be on PCIe and
USB for bluetooth. This patch solves the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FreeBSD driver [0] uses the same 2G values as for the AR9280 chips.
Using the same values in ath9k results in much better throughput for me.
Before this patch I had a huge amount of packet loss (sometimes up to
40%) and the max transfer speed was somewhere around 5Mbit/s. With this
patch applied I have zero packet loss and ten times the throughput.
My device uses a AR9227 which is the PCI variant of the AR9287.
[0] http://bxr.su/FreeBSD/sys/dev/ath/ath_hal/ar9002/ar9287.h
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes the warnings like
"plane A assertion failure, should be disabled but not"
that on the initial modeset during boot. This can happen if
the primary plane is enabled by the firmware, but inheriting
it fails because the DMAR is active or for other reasons.
Most likely caused by
commit 36750f284b
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 1 12:49:54 2015 +0200
drm/i915: update plane state during init
This is a new version of
commit 721a09f739
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Sep 15 14:28:54 2015 +0200
drm/i915: Add primary plane to mask if it's visible
That was reverted in order to facilitate easier backporting of some
commits from -next to v4.3.
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91429
Reported-and-tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from -next to v4.3]
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move the sprite/cursor plane disabling to occur in intel_sanitize_crtc()
where it belongs instead of doing it in intel_modeset_readout_hw_state().
The plane disabling was first added in
4cf0ebbd4f drm/i915: Rework plane readout.
I got the idea from some patches from Partik and/or Maarten but those
moved also the plane state readout to intel_sanitize_crtc() which isn't
quite right in my opinion.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=91910
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from -next to v4.3]
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The dotclock is often calculated in encoder .get_config(), so we
shouldn't copy the adjusted_mode to hwmode until we have read out the
dotclock.
Gets rid of some warnings like these:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 21: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 0 is disabled
v2: Steal Maarten's idea to move crtc->mode etc. assignment too
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91428
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from -next to v4.3]
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
