Enable controller Low-Power-Mode if we have a pdev to manage host
wake-up. Once LPM is enabled, controller notifies its TX status via
a vendor specific packet (tx_idle/tx_active).
tx_active means that there is more data upcoming from controller.
tx_idle means that controller can be put in suspended state.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An IRQ can be retrieved from the pdev resources. This irq will be used
in case of LPM suspend mode to wake-up the host and resume the link.
This resource can be declared as a GPIO-Interrupt which requires to be
converted into IRQ.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add specific bluetooth device logging macros since hci device name is
repeatedly referred in bluetooth subsystem logs.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some counterfeit CSR controllers also have broken behavior with the
HCI_Read_Stored_Link_Key command:
< HCI Command: Read Stored Link Key (0x03|0x000d) plen 7
Address: 00:00:00:00:00:00 (OUI 00-00-00)
Read all: 0x01
> HCI Event: Command Complete (0x0e) plen 8
Read Stored Link Key (0x03|0x000d) ncmd 1
Status: Unsupported Feature or Parameter Value (0x11)
Max num keys: 0
Num keys: 0
Extend the existing HCI_QUIRK_BROKEN_STORED_LINK_KEY to be also used
for this HCI command.
Reported-and-tested-by: Rhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This was missed in the original commit adding the flag and ath10k only printed "bit10":
ath10k_pci 0000:02:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70.6-2 api 3
htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,bit10
Also add a build test to avoid this happening again.
Fixes: ccec9038c7 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce "regulator-allow-set-load" property to make it possible to
flag in the board configuration that a regulator is allowed to have the
load requirements changed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
chipselect (in the case of spi-gpio: spi_gpio_chipselect, which
calls gpiod_set_raw_value_cansleep) can sleep, so we should not
hold a spinlock while calling it from spi_bitbang_setup.
This issue was introduced by this commit, which converted spi-gpio
to cansleep variants:
d9dda5a191 "spi: spi-gpio: Use 'cansleep' variants to access GPIO"
Replacing the lock variable by a mutex fixes the issue: This is
safe as all instances where the lock is used are called from
contexts that can sleep.
Finally, update spi-ppc4xx and and spi-s3c24xx to use mutex
functions, as they directly hold the lock for similar purpose.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vdevs associated with a given chanctx should be
restarted if the bandwidth changes. Otherwise
traffic may cease.
This is known to fix STA CSA with bandwidths wider
than 20MHz.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary to make vdev restarting logic
reusable later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The remain_on_channel callback needs different
timeout. Calling ieee80211_queue_work() with a
shorter delay after calling it with a longer delay
will not change the timer. This caused the
offchannel timeout worker to not trigger in time
and caused the device to stay on channel longer
then expected. This could cause some problems and
was be easily reproduced with `iw offchannel`
command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Cortex-A53 processors <= r0p4 are affected by erratum #843419 which can
lead to a memory access using an incorrect address in certain sequences
headed by an ADRP instruction.
There is a linker fix to generate veneers for ADRP instructions, but
this doesn't work for kernel modules which are built as unlinked ELF
objects.
This patch adds a new config option for the erratum which, when enabled,
builds kernel modules with the mcmodel=large flag. This uses absolute
addressing for all kernel symbols, thereby removing the use of ADRP as
a PC-relative form of addressing. The ADRP relocs are removed from the
module loader so that we fail to load any potentially affected modules.
Cc: <stable@vger.kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When saving/restoring the VFP registers from a compat (AArch32)
signal frame, we rely on the compat registers forming a prefix of the
native register file and therefore make use of copy_{to,from}_user to
transfer between the native fpsimd_state and the compat_vfp_sigframe.
Unfortunately, this doesn't work so well in a big-endian environment.
Our fpsimd save/restore code operates directly on 128-bit quantities
(Q registers) whereas the compat_vfp_sigframe represents the registers
as an array of 64-bit (D) registers. The architecture packs the compat D
registers into the Q registers, with the least significant bytes holding
the lower register. Consequently, we need to swap the 64-bit halves when
converting between these two representations on a big-endian machine.
This patch replaces the __copy_{to,from}_user invocations in our
compat VFP signal handling code with explicit __put_user loops that
operate on 64-bit values and swap them accordingly.
Cc: <stable@vger.kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We have a couple of CPU hotplug notifiers for resetting the CPU debug
state to a sane value when a CPU comes online.
This patch ensures that we mask out CPU_TASKS_FROZEN so that we don't
miss any online events occuring due to suspend/resume.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for mesh to ath10k. We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.
Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode. As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true. The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.
When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:
ip link set wlan0 down
iw dev wlan0 set type mp
ip link set wlan0 up
iw dev wlan0 set freq 5745 80 5775
iw dev wlan0 mesh join mesh-vht
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the case of raw mode without nohwcrypt parameter, we
should still make sure the frame is protected before
adding MIC_LEN to avoid skb_under_panic errors.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, ath10k restricts received frames to those matching BSSID.
When other BSS frames are requested (e.g. in mesh mode), add an internal
monitor device so those frames are not filtered.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An user will be CSR SiRFSoC ARM chips.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some chips have separate unmask registers from mask registers for
some consideration of concurrency SMP write performance. And this
patch adds a flag for it.
An user will be CSR SiRFSoC ARM chips.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/sunxi/sun4i-codec.c:708:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The slot_width is for essentially same thing. Instead of storing
bclk_lrclk_ratio, just store the slot_width. Comments has been updated
accordingly and some variable names changed to more descriptive.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply PTR_ERR to the value that was recently assigned.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
@@
if (IS_ERR(x) || ...) {
... when any
when != IS_ERR(...)
(
PTR_ERR(x)
|
* PTR_ERR(y)
)
... when any
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store return value of of_get_property() to a pointer of __be32 type as
device tree has big endian type. This fixes a sparse warning couple of
lines later when be32_to_cpup() is used to convert from big endian to
cpu endian.
The whole conversion is not really necessary, as we are only checking
if the value is zero or not, but I wanted to add it to remind in the
future that the data has to be converted before use. Compiler should
optimize the unnecessary operations away.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier revisions of the wm5110/8280 silicon require a slightly more
complex procedure to enable analogue inputs. This patch adds this into
the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several actions that smp_conn_security() might make that do
not require a valid SMP context (conn->smp pointer). One of these
actions is to encrypt the link with an existing LTK. If the SMP
context wasn't initialized properly we should still allow the
independent actions to be done, i.e. the check for the context should
only be done at the last possible moment.
Reported-by: Chuck Ebbert <cebbert.lkml@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0+
ioremap_cache() is currently not available on some architectures.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The commit [b67893206f: leds:lp55xx: fix firmware loading error]
tries to address the firmware file handling with user helper, but it
sets a wrong Kconfig CONFIG_FW_LOADER_USER_HELPER_FALLBACK. Since the
wrong option was enabled, the system got a regression -- it suffers
from the unexpected long delays for non-present firmware files.
This patch corrects the Kconfig dependency to the right one,
CONFIG_FW_LOADER_USER_HELPER. This doesn't change the fallback
behavior but only enables UMH when needed.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=944661
Fixes: b67893206f ('leds:lp55xx: fix firmware loading error')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vma'
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vmf'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'old'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'new'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'frontbuffer_bits'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move, replace and reorganize comments to stay under 80 characters
per line, as to follow the kernel code style. Some unuseful comments
have been removed.
Signed-off-by: Raphaël Beamonte <raphael.beamonte@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the drivers.c file that fixes
a block comment style.
Signed-off-by: Marcos Canán <mcanan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates the ugly Hal_EEValueCheck() function
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function pointer wlan_handle_rx_que is not called anywhere. Delete
wlan_handle_rx_que and it's assignment code.
But the function wilc_wlan_handle_rxq in assignment code is used. So leave it.
Signed-off-by: Glen Lee <glen.lee@atmel.com>
Signed-off-by: Tony Cho <tony.cho@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INLINE macro is defined as static __inline so that it is replaced by
static inline.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bit shift macro that is custom defined, then replace BIT(x)
macro.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rxq_thread never runs since it's kthread_run code was delete in a previous
patch. Remove kthread_run and it's related codes.
Signed-off-by: Glen Lee <glen.lee@atmel.com>
Signed-off-by: Tony Cho <tony.cho@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
