This function is new in v4.2-rc1 and makes a forward declaration of the
match table superfluous which can so be removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since commit ef90174f82 ("watchdog: watchdog_core: Add watchdog
registration deferral mechanism") there is no need to delay the call to
watchdog_register_device any more. So simplify the registration code
accordingly.
Resetting wd_base to NULL can the also be dropped because nothing
depends on it being NULL to signal probe failure any more. (The matching
wd_base = NULL in .remove was missing, too.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer found in NXP LPC SoCs
family, which includes LPC18xx/LPC43xx. Other SoCs in that family may
share the same watchdog hardware.
Watchdog driver registers a restart handler that will restart the system
by performing an incorrect feed after ensuring the watchdog is enabled in
reset mode.
As watchdog cannot be disabled in hardware, driver's stop routine will
regularly send a keepalive ping using a timer.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
During probe for an always-running watchdog a timer is setup to
constantly ping the watchdog while the device is not open. The gpio to
ping the watchdog is setup to inactive.
For a watchdog with hw_algo = "toggle" this results in a ping depending
on the initial state of the gpio, for hw_algo = "level" no ping is
generated.
Make sure that the first automatic ping is sent immediately and not only
when the timer expires the first time. This makes the machine survive in
case more than half of the watchdog timeout is already elapsed. (Which
is very probable for the chip I'm faced with that has a timeout of one
second.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
strncmp(algo, "toggle", 6) doesn't compare the trailing '\0' byte, so
using
hw_algo = "toggleboggle"
is recognized the same way as
hw_algo = "toggle"
. While this doesn't introduce any problems for a device tree that
sticks to the documented settings it's still ugly.
Fix this by using strcmp to only match on "toggle" and "level".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog has an input clock, the slow clock. It is required as it will
not function without it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit f48da8b14d (xen-netback: fix
unlimited guest Rx internal queue and carrier flapping) introduced a
regression.
The PV frontend in IPXE only places 4 requests on the guest Rx ring.
Since netback required at least (MAX_SKB_FRAGS + 1) slots, IPXE could
not receive any packets.
a) If GSO is not enabled on the VIF, fewer guest Rx slots are required
for the largest possible packet. Calculate the required slots
based on the maximum GSO size or the MTU.
This calculation of the number of required slots relies on
1650d5455b (xen-netback: always fully coalesce guest Rx packets)
which present in 4.0-rc1 and later.
b) Reduce the Rx stall detection to checking for at least one
available Rx request. This is fine since we're predominately
concerned with detecting interfaces which are down and thus have
zero available Rx requests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog infrastructure checks the maximum timeout for us.
Use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Tested on the Nvidia chipset with an SMBus controller PCI ID 0x0AA2
(as shown in the PCI listing during the boot sequence).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit f2147de334 ("watchdog: sunxi: support parameterized compatible
strings") introduced a regression in sunxi_wdt_start(), by which
the system reset function of the watchdog is not enabled upon
starting the watchdog. As a result, the system is not reset when the
watchdog expires. Fix it.
Fixes: f2147de334 ("watchdog: sunxi: support parameterized compatible strings")
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@vger.kernel.org
Without .shutdown(), watchdog might reset the system during power off.
For example, if watchdog's timeout is set to 30s, then it is reset to
zero by mtk_wdt_ping(). During power off, no app will ping watchdog,
but watchdog is still running and may trigger reset.
Signed-off-by: Greta Zhang <greta.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog test program is much more useful if it can configure the
timeout value and ping rate. This will allow you to test actual timeouts.
Adds the -t parameter to set the timeout value (in seconds), and -p to set
the ping rate (number of seconds between pings).
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hariprasad Shenai says:
====================
cxgb4: Fix tx flit calculation and wc stat configuration
This patch series fixes the following:
Patch 1/2 fixes tx flit calculation, which if wrong can lead to
stall, hang, data corrpution, write combining failure. Patch 2/2 fixes
PCI-E write combining stats configuration.
This patch series has been created against net tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The write-combining configuration register SGE_STAT_CFG_A needs to
be configured after FW initializes the adapter, else FW will reset
the configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0aac3f56d4 ("cxgb4: Add comment for calculate tx flits
and sge length code") introduced a regression where tx flit calculation
is going wrong, which can lead to data corruption, hang, stall and
write-combining failure. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_off() prior to register_netdev(), otherwise
userspace can see incorrect link state.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some reverts for some tty patches (specifically the pl011
driver) that ended up breaking a bunch of machines (i.e. almost all of
the ones with this chip.) People are working on a fix for this, but in
the meantime, it's best to just revert all 5 patches to restore people's
serial consoles.
These reverts have been in linux-next for many days now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXvtvkACgkQMUfUDdst+ynEVACgvMxKazgRqCnYcqbQs9DwARds
0r4AoL51IVIQe976ZYSjUdSFL+Q0IE1t
=LOn1
-----END PGP SIGNATURE-----
Merge tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver reverts from Greg KH:
"Here are some reverts for some tty patches (specifically the pl011
driver) that ended up breaking a bunch of machines (i.e. almost all
of the ones with this chip).
People are working on a fix for this, but in the meantime, it's best
to just revert all 5 patches to restore people's serial consoles.
These reverts have been in linux-next for many days now"
* tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "uart: pl011: Rename regs with enumeration"
Revert "uart: pl011: Introduce register accessor"
Revert "uart: pl011: Introduce register look up table"
Revert "uart: pl011: Improve LCRH register access decision"
Revert "uart: pl011: Add support to ZTE ZX296702 uart"
* SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
* SPI NOR: a few new IDs / feature flags
* OMAP2 NAND: rename module so it doesn't conflict with onenand omap2.ko
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aXrv
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd
Pull more MTD updates from Brian Norris:
"There was one significant bug in my first pull request, fixed here. I
also threw in a few trivial ID additions and a small module rename.
Details:
- SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
- SPI NOR: a few new IDs / feature flags
- OMAP2 NAND: rename module so it doesn't conflict with onenand
omap2.ko"
* tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd:
mtd: spi-nor: fix NULL dereference when no match found in spi_nor_ids[]
mtd: spi-nor: s25sl064p supports both dual and quad I/O
mtd: spi-nor: allow dual/quad reads on S25FL129P
mtd: nand: omap2: Rename shippable module to omap2_nand
mtd: spi-nor: Add support for sst25wf020a
mtd: spi-nor: Add support for Micron n25q064a serial flash
This set of changes introduces the beginnings of a new API that's based
around the concept of states that can be atomically applied. Drivers go
to various lengths to implement something similar, which indicates that
the core should really be providing the necessary framework.
On top of that, there is a bit of cleanup as well as improved kerneldoc
and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of SoCs
and a couple of fixes for existing drivers (pca9685, Broadcom Kona and
Atmel HLCDC).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ymH8
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces the beginnings of a new API that's
based around the concept of states that can be atomically applied.
Drivers go to various lengths to implement something similar, which
indicates that the core should really be providing the necessary
framework.
On top of that, there is a bit of cleanup as well as improved
kerneldoc and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of
SoCs and a couple of fixes for existing drivers (pca9685, Broadcom
Kona and Atmel HLCDC)"
* tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
ARM: at91: pwm: atmel-hlcdc: Add at91sam9n12 errata
pwm: Add NXP LPC18xx PWM/SCT DT binding documentation
pwm: NXP LPC18xx PWM/SCT driver
pwm-pca9685: Support changing the output frequency
pwm-pca9685: Fix several driver bugs
pwm: kona: Modify settings application sequence
pwm: pca9685: Drop owner assignment
pwm: Add to device-drivers documentation
pwm: Clean up kerneldoc
pwm: Remove useless whitespace
pwm: sysfs: Remove unnecessary padding
pwm: sysfs: Properly convert from enum to string
pwm: Make use of pwm_get_xxx() helpers where appropriate
pwm: Add pwm_get_polarity() helper function
pwm: Constify PWM device where possible
pwm: Add the pwm_is_enabled() helper
Followup to the UFS series - with the way we clear the new blocks (via
buffer cache, possibly on more than a page worth of file) we really
should not insert a reference to new block into inode block tree until
after we'd cleared it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virtio-mmio can now be auto-loaded through acpi.
virtio blk supports extended partitions.
total memory is better reported when using virtio balloon with auto-deflate.
cache control is re-enabled when using virtio-blk in modern mode.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV7/iUAAoJECgfDbjSjVRpzRIIAMJz5enk2FbyiOsky5THASqK
rWAEx+Jz5Av3FVM99W+Fs8dmXrBGkCTyRgmX3mZx+pGNhOsLjc6xHElTekzwQBas
18oFsQDTWk0rPZkO7X6/OY3GgHyq8VSI/2kW+yKMYj4k/gAaGV+Azf0m5DGMp4wn
rngevvcDSkFEN2Gjxbi3MWT8sJ9Br/EFg6KzKUOiOycHh/rQZsaQK6tq4kpUZkil
2wvXspQY6ix2fD558gsiqUv6l8yZ9mXVgxtyRcnxjfM+8jr+qtqai8yVGCAC5krh
50RXrR22tN/6aLYuvtPj46+Y0dleCMEwW2rSmcw5h5yr3B/0ylnZ1YNp6vlFyv0=
=8xQ2
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Virtio fixes and features for 4.3:
- virtio-mmio can now be auto-loaded through acpi.
- virtio blk supports extended partitions.
- total memory is better reported when using virtio balloon with
auto-deflate.
- cache control is re-enabled when using virtio-blk in modern mode"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: do not change memory amount visible via /proc/meminfo
virtio_ballon: change stub of release_pages_by_pfn
virtio-blk: Allow extended partitions
virtio_mmio: add ACPI probing
virtio-blk: use VIRTIO_BLK_F_WCE and VIRTIO_BLK_F_CONFIG_WCE in virtio1
Just a couple of changes for v4.3-rc1. A preparatory IRQ patch to
prepare for moving irq_data struct members, and a tweak to
Documentation/features since Meta2 could support THP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=skwh
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag updates from James Hogan:
"Metag architecture changes for v4.3.
Just a couple of changes for v4.3-rc1. A preparatory IRQ patch to
prepare for moving irq_data struct members, and a tweak to
Documentation/features since Meta2 could support THP"
* tag 'metag-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
Documentation/features/vm: Meta2 is capable of THP
metag/irq: Use access helper irq_data_get_affinity_mask()
Pull cifs updates from Steve French:
"Small cifs fix and a patch for improved debugging"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix use-after-free on mid_q_entry
Update cifs version number
Add way to query server fs info for smb3
As part of the v4.3 merge window the DAX code was updated by Matthew and
Kirill to handle PMD pages. Also as part of the v4.3 merge window we
updated the DAX code to do proper PMEM flushing (commit 2765cfbb34:
"dax: update I/O path to do proper PMEM flushing").
The additional code added by the DAX PMD patches also needs to be
updated to properly use the PMEM API. This ensures that after a PMD
fault is handled the zeros written to the newly allocated pages are
durable on the DIMMs.
linux/dax.h is included to get rid of a bunch of sparse warnings.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>,
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Kirill Shutemov <kirill@shutemov.name>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit f3f601c1d2.
UAPI headers cannot use "uapi/" in their paths by design -- when they're
installed, they do not have the uapi/ prefix. Otherwise doing so breaks
userland badly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
This may cause issues because encoders are already destroyed so removing
active primaries may use freed memory. Instead free the fb directly,
ignoring refcount.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The errata for HLCDC PWM of at91sam9n12 are the same as for at91sam9x5.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Right now, drm_sysfs_create() returns the newly allocated "struct class"
to the caller (which is drm_core_init()), which then has to set the
global variable 'drm_class'. During cleanup, though, we call
drm_sysfs_destroy() which implicitly uses the global 'drm_class'. This is
confusing, as ownership of the global 'drm_class' is non-obvious.
This patch changes drm_sysfs_create() to drm_sysfs_init() and makes it
initialize the 'drm_class' object directly, rather than returning it.
This way, both drm_sysfs_init() and drm_sysfs_destroy() work in a similar
fashion and manage the global drm class.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify `foo == NULL || IS_ERR(foo)` via IS_ERR_OR_NULL(). This is
pretty commonly used all over the kernel, especially for debugfs/sysfs
cleanup paths.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit adds support for NXP LPC18xx PWM/SCT.
NXP LPC SoCs family, which includes LPC18xx/LPC43xx, provides a State
Configurable Timer (SCT) which can be configured as a Pulse Width
Modulator. Other SoCs in that family may share the same hardware.
The PWM supports a total of 16 channels, but only 15 can be simultaneously
requested. There's only one period, global to all the channels, thus PWM
driver will refuse setting different values to it, unless there's only one
channel requested.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
[thierry.reding@gmail.com: remove excessive padding of fields]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
drm_av_sync_delay() doesn't change the passed in mode, so make it const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_select_eld() doesn't look at the passed in mode, so don't pass it
in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
valid_inferred_mode() don't change the modes over which it iterates,
so make the iterator const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the SSP port settings are being clobbered as part of the DSP
RTD3 restore logic. make sure we save the correct params and restore them
at resume. The FW sadly does not save SSP settings as part of the PM
context.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes hardware reports invalid mcs index in rx descriptor
when operating in VHT80 mode and all packets with invalid mcs
will be eventually dropped in mac80211. This issue is observerd during
testing on QCA99X0 chipsets.
This patch adds a warn message for dumping the rx desc info which helps
in analysing the issue when invalid mcs is received.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to the VHT STS, this is supposed to be propagated by firmware.
In case it's not, use the default value, but as last resort.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The VHT STS CAP shall be reported by firmware to host, like in case of
QCA99x0. For QCA6174 hw family this isn't set for some reason.
So for this particular chips, let's assume it has the ability to
support VHT NDP in up to 4 STSs (which is true by the way).
Change the published beamformee STS cap accordingly to 3 or to what
the firmware reports.
Assumption so far, it suppose to be the num_rf_chains-1, was
completely wrong.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.
Fix this by limiting the probe responses when the specified
threshold limit is reached.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.
To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.
Failure happens with the following stack trace
[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
