st21nfcb does support another phy than i2c: spi.
st21nfcc does not support spi as the spi ios are used
by the AMS RF booster.
st21nfcb is not following NCI NFC Forum recommendations for spi
but rely on ST prioritary protocol ndlc as for i2c.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PCB_SYNC different than PCB_TYPE_SUPERVISOR or PCB_TYPE_DATAFRAME
should be discarded.
Irrelevant data may be forwarded up to the ndlc state machine by
phys like spi to prevent missing potential data during "write"
transactions.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving a NDLC PCB_SYNC_ACK the pending data was never
removed from ack_pending_q and cleared.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st_nci_hci_load_session() calls kfree_skb() on unitialized
variables skb_pipe_info and skb_pipe_list if the call to
nci_hci_connect_gate() failed. Reword the error path to not use
these variables when they are not initialized. While at it, there
seemed to be a memory leak because skb_pipe_info was only freed
once, after the for-loop, even though several ones were created
by nci_hci_send_cmd.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca_hci_load_session() calls kfree_skb() on unitialized
variables skb_pipe_info and skb_pipe_list if the call to
nfc_hci_connect_gate() failed. Reword the error path to not use
these variables when they are not initialized. While at it, there
seemed to be a memory leak because skb_pipe_info was only freed
once, after the for-loop, even though several ones were created
by nfc_hci_send_cmd.
Fixes: ec03ff1a8f
("NFC: st21nfca: Remove skb_pipe_list and skb_pipe_info
useless allocation")
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a copy and paste error st_nci_i2c_read still contains
st21nfca header comment.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace ST21NFCB with ST_NCI or st21nfcb with st_nci as it
was forgotten in commit "nfc: st-nci: Rename st21nfcb to st-nci"
ed06aeefda
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Merge x86 fixes from Ingo Molnar:
"Two followup fixes related to the previous LDT fix"
Also applied a further FPU emulation fix from Andy Lutomirski to the
branch before actually merging it.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
x86/ldt: Further fix FPU emulation
x86/ldt: Correct FPU emulation access to LDT
x86/ldt: Correct LDT access in single stepping logic
fuse_dev_ioctl() performed fuse_get_dev() on a user-supplied fd,
leading to a type confusion issue. Fix it by checking file->f_op.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are nroken without these two fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5Tu
-----END PGP SIGNATURE-----
Merge tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.
* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
Signed-off-by: Olof Johansson <olof@lixom.net>
Shut up this compiler warning that I get during the daily build:
horus3a.c: In function 'horus3a_set_params':
horus3a.c:308:24: warning: 'rolloff' may be used uninitialized in this function [-Wmaybe-uninitialized]
symbol_rate * (100 + rolloff), 200000) + 5;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from do_gettimeofday is susceptible to sudden jumps due to
user setting the time or due to NTP.
Monotonic time is constantly increasing time better suited for comparing two
timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from do_gettimeofday is susceptible to sudden jumps due to
user setting the time or due to NTP.
Monotonic time is constantly increasing time better suited for comparing two
timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Header claims GPL v2, so make the MODULE_LICENSE reflect that properly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In videobuf_setup reject buffers that are too small for the configured
format. Fixes v4l2-compliance issue.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Reviewed-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adapt rcar_vin_querycap() so that cap->bus_info is populated with
something meaningful/unique.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This adds V4L2_MBUS_FMT_RGB888_1X24 input format support
which is used by the ADV7612 chip.
Modified to use MEDIA_BUS_FMT_* constants
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commits moves the Intersil/Techwell PCI vendor ID, and
the device IDs for the TW68 PCI video capture cards.
This will allow to support future Intersil/Techwell devices
without duplicating the IDs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On the place of the source entity name, the sink entity name was printed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platforms using the OMAP3 ISP have all switched to DT, drop platform
data support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert g2d_userptr_get_dma_addr() to pin pages using get_vaddr_frames().
This removes the knowledge about vmas and mmap_sem locking from exynos
driver. Also it fixes a problem that the function has been mapping user
provided address without holding mmap_sem.
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Conversion to the use of pinned pfns made some functions unused. Remove
them. Also there's no need to lock mmap_sem in __buf_prepare() anymore.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_dc_get_userptr() to use frame vector infrastructure. When we
are doing that there's no need to allocate page array and some code can
be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_vmalloc_get_userptr() to use frame vector infrastructure.
When we are doing that there's no need to allocate page array and some
code can be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide simple helper functions to map virtual address range into an
array of pfns / pages.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns() instead of
hand made mapping of virtual address to physical address. Also the
function leaked page reference from get_user_pages() so fix that by
properly release the reference when omap_vout_buffer_release() is
called.
Signed-off-by: Jan Kara <jack@suse.cz>
[hans.verkuil@cisco.com: remove unused variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide new function get_vaddr_frames(). This function maps virtual
addresses from given start and fills given array with page frame numbers of
the corresponding pages. If given start belongs to a normal vma, the function
grabs reference to each of the pages to pin them in memory. If start
belongs to VM_IO | VM_PFNMAP vma, we don't touch page structures. Caller
must make sure pfns aren't reused for anything else while he is using
them.
This function is created for various drivers to simplify handling of
their buffers.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently vb2 core acquires mmap_sem just around call to
__qbuf_userptr(). However since commit f035eb4e97 (videobuf2: fix
lockdep warning) it isn't necessary to acquire it so early as we no
longer have to drop queue mutex before acquiring mmap_sem. So push
acquisition of mmap_sem down into .get_userptr memop so that the
semaphore is acquired for a shorter time and it is clearer what it is
needed for.
Note that we also need mmap_sem in .put_userptr memop since that ends up
calling vb2_put_vma() which calls vma->vm_ops->close() which should be
called with mmap_sem held. However we didn't hold mmap_sem in some code
paths anyway (e.g. when called via vb2_ioctl_reqbufs() ->
__vb2_queue_free() -> vb2_dma_sg_put_userptr()) and getting mmap_sem in
put_userptr() introduces a lock inversion with queue->mmap_lock in the
above mentioned call path.
Luckily this whole locking mess will get resolved once we convert
videobuf2 core to the new mm helper which avoids the need for mmap_sem
in .put_userptr memop altogether.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sr030pc30_get_fmt() can only succeed if both info->curr_win and
info->curr_fmt are not NULL.
If one of those vars are null, the curent code would call:
ret = sr030pc30_set_params(sd);
If the curr_win is null, it will return -EINVAL, as it would be
expected. However, if curr_fmt is NULL, the function won't
set it.
The code will then try to read from it:
mf->code = info->curr_fmt->code;
mf->colorspace = info->curr_fmt->colorspace;
with obviouly won't work.
This got reported by smatch:
drivers/media/i2c/sr030pc30.c:505 sr030pc30_get_fmt() error: we previously assumed 'info->curr_win' could be null (see line 499)
drivers/media/i2c/sr030pc30.c:507 sr030pc30_get_fmt() error: we previously assumed 'info->curr_fmt' could be null (see line 499)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Why to store the chosed values for prediv, postdiv and mult if
those won't be used?
drivers/media/i2c/ov2659.c: In function 'ov2659_pll_calc_params':
drivers/media/i2c/ov2659.c:912:35: warning: variable 's_mult' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:20: warning: variable 's_postdiv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:6: warning: variable 's_prediv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
This is likely some leftover from some past change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:148:19: warning: Variable length array is used.
As the maximum size is 1026, we can't use dynamic var, as it
would otherwise spend 1056 bytes of the stack at i2c_wr() function.
So, allocate a buffer with the allowed maximum size together with
the state var.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.
Fixes: 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix style issue related to missing braces, detected by checkpatch.pl.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix alignment for function parameters as suggested by checkpatch.pl.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently registers a pair of irq handlers using
request_threaded_irq(), however the synchronization mechanism between the
hardirq and the threadedirq handler is a regular spinlock.
Unfortunately, this breaks PREEMPT_RT builds, where a spinlock can sleep,
and is thus not able to be acquired from a hardirq handler. This patch gets
rid of the threaded handler and pushes all interrupt handling into the
hardirq context, and uses request_irq().
To validate that this change has no impact on RT performance, here are
cyclictest values with no processes running:
$ sudo cyclictest -S -m -p 98
policy: fifo: loadavg: 0.00 0.01 0.05 1/174 2539
T: 0 ( 1405) P:98 I:1000 C:167010520 Min: 9 Act: 12 Avg: 12 Max: 75
T: 1 ( 1862) P:98 I:1500 C:111340339 Min: 9 Act: 12 Avg: 12 Max: 73
Then, all xadc raw handles were accessed in a continuous loop via
/sys/bus/iio/devices/iio:device0:
$ sudo cyclictest -S -m -p 98
policy: fifo: loadavg: 7.84 7.70 7.63 3/182 4260
T: 0 ( 2559) P:98 I:1000 C:241557018 Min: 11 Act: 18 Avg: 21 Max: 74
T: 1 ( 2560) P:98 I:1500 C:161038006 Min: 10 Act: 21 Avg: 20 Max: 73
Signed-off-by: Xander Huff <xander.huff@ni.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Load the driver using the below command:
echo hmc5983 0x1e > /sys/bus/i2c/devices/i2c-?/new_device
In sysfs, the iio name is hmc5843, however the i2c name is hmc5983,
they are inconsistent.
With this patch, the iio name will be the same as the i2c device name
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes the error from iio_event_getfd() percolate up
to userspace properly so we can know for sure there is no
events on this device (-ENODEV returned). Before this patch
we would bail out looking for the unsupported events on the
erroneous (negative) file descriptor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently if generic_buffer is invoked without first enabling any
channels in scan_elements/*_en, it will fail unable to enable the
buffer because bytes_per_datum inside the kernel will be zero if
no channels are available.
It is implied that the user of the program should enable channels
manually or with a script before executing generic_buffer.
Be more helpful by stopping execution if no enabled channels can
be found, and print a helptext that will tell you what is wrong
and what needs to be done.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes the event monitor bail out with a helpful error
message if a device does not support events, as a related
fix to iio core now makes it return -ENODEV properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the documentation ABI for the remove_trigger
attribute, provided by the iio-trig-sysfs stand-alone driver.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the ABI documentation for the add_trigger
attribute, which is provided by the iio-trig-sysfs stand-alone driver.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
