If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0x3 only masks two bits, but three bits have to be allowed. This fixes
GPHY0 LED2 (which is the highest bit of phy2) on my board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Interrupts were missed if an 8-bit integer overflow occurred. This was
observed when bank0,pin7 and bank1,pin7 changed simultaniously.
As the 8-bit totals were only checked against zero, replace them with
booleans. Name the booleans so that their purpose is clear.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The omap_gpio_irq_startup() can be called at time when:
- corresponding GPIO has been requested already and in this case
it has to be configured as input already. If not - return with -EINVAL
and do not try to re-configure it as it could be unsafe.
- corresponding GPIO is free: reconfigure GPIO as input.
In addition, call omap_enable_gpio_module directly as all needed
checks are already present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO Chip implementation shouldn't touch GPIO IRQ specific registers
and vise versa.
Hence, rework omap_gpio_request:
- don't reset GPIO IRQ triggering type to IRQ_TYPE_NONE, because
GPIO irqchip should be responsible for that;
- call directly omap_enable_gpio_module as all needed checks are already
present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO IRQ Chip implementation shouldn't touch GPIO specific
registers and vise versa.
Hence, rework omap_gpio_irq_shutdown and try to touch only irqs specific
registers:
- don't configure GPIO as input (it, actually, should be already configured
as input).
- don't clear debounce configuration if GPIO is still used as GPIO.
We need to take in to account here commit c9c55d9211
("gpio/omap: fix off-mode bug: clear debounce settings on free/reset").
Also remove omap_reset_gpio() function as it is not used any more.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO bank will be kept powered in case if input parameters
are invalid or error occurred in omap_gpio_irq_type.
Hence, fix it by ensuring that GPIO bank will be unpowered
in case of errors and add additional check of value returned
from omap_set_gpio_triggering().
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes following issue:
- GPIOn is used as IRQ by some dev, for example PCF8575.INT -> gpio6.11
- PCFx driver knows nothing about type of IRQ line (GPIO or not)
so it doesn't request gpio and just do request_irq()
- If gpio6.11 will be exported through the sysfs and then un-xeported
then IRQs from PCFx will not be received any more, because
IRQ configuration for gpio6.11 will be cleaned up unconditionally
in omap_gpio_free.
Fix this by removing all GPIO IRQ specific code from omap_gpio_free()
and also do GPIO clean up (change direction to 'in' and disable debounce)
only if corresponding GPIO is not used as IRQ too.
GPIO IRQ will be properly cleaned up by GPIO irqchip code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, e3, e4, a, b;
@@
-init_timer(&e1);
+setup_timer(&e1, a, b);
... when != a = e2
when != b = e3
-e1.function = a;
... when != b = e4
-e1.data = b;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move the functions that are used by both the initiator and target
subsystems into scsi_common.c/.h. This change will allow to remove
the initiator SCSI header include directives from most SCSI target
source files in a later patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Move the constants that are used by both initiator and target
drivers into the new header file <scsi/scsi_proto.h>. This change
will allow to remove the initiator SCSI header include directives
from most SCSI target source files in a later patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch is rebased on top of recently sent 18 patches(submitted by me) for
megaraid_sas driver.
Change the return value of wait_and_poll() and megsas_issue_blocked_cmd()
based on MFI_STAT returned by firmware for that command. Earlier driver always
send return type based on command completion (but never check MFI_STAT_OK for
that command), so even if command is failed by firmware still driver will
return SUCCESS status from these functions wait_and_poll() and
megsas_issue_blocked_cmd() and if caller of these functions does not check
command status (MFI_STAT), then it may endup using invalid data returned in
DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to
avoid this type of issue is do error handling and set proper return type from
caller function wait_and_poll() and megsas_issue_blocked_cmd().
The change proposed in this patch will fix the regression introduced in patch-
"90dc9d9 megaraid_sas : MFI MPT linked list corruption fix" inside function
megasas_ld_list_query(). Prior to this MFI MPT linked list corruption fix
patch, megasas_ld_list_query() function used to check DCMD status(returned by
firmware) but with this linked list corruption fix patch, DCMD status will not
be checked inside function megasas_ld_list_query() and introduced this issue
of wrong data being used by function megasas_ld_list_query().
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add the ACL related protocol definitions which were added in the NFSv4.1
specification.
(But we're not using them yet.)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Problem: When an operation like WRITE receives a BAD_STATEID, even though
recovery code clears the RECLAIM_NOGRACE recovery flag before recovering
the open state, because of clearing delegation state for the associated
inode, nfs_inode_find_state_and_recover() gets called and it makes the
same state with RECLAIM_NOGRACE flag again. As a results, when we restart
looking over the open states, we end up in the infinite loop instead of
breaking out in the next test of state flags.
Solution: unset the RECLAIM_NOGRACE set because of
calling of nfs_inode_find_state_and_recover() after returning from calling
recover_open() function.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The VNET_LE flag was introduced to fix accesses to virtio 1.0 headers
that are always little-endian. It can also be used to handle the special
case of a legacy little-endian device implemented by a big-endian host.
Let's add a flag and ioctls for big-endian devices as well. If both flags
are set, little-endian wins.
Since this is isn't a common usecase, the feature is controlled by a kernel
config option (not set by default).
Both macvtap and tun are covered by this patch since they share the same
API with userland.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
This patch brings cross-endian support to vhost when used to implement
legacy virtio devices. Since it is a relatively rare situation, the
feature availability is controlled by a kernel config option (not set
by default).
The vq->is_le boolean field is added to cache the endianness to be
used for ring accesses. It defaults to native endian, as expected
by legacy virtio devices. When the ring gets active, we force little
endian if the device is modern. When the ring is deactivated, we
revert to the native endian default.
If cross-endian was compiled in, a vq->user_be boolean field is added
so that userspace may request a specific endianness. This field is
used to override the default when activating the ring of a legacy
device. It has no effect on modern devices.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
The current memory accessors logic is:
- little endian if little_endian
- native endian (i.e. no byteswap) if !little_endian
If we want to fully support cross-endian vhost, we also need to be
able to convert to big endian.
Instead of changing the little_endian argument to some 3-value enum, this
patch changes the logic to:
- little endian if little_endian
- big endian if !little_endian
The native endian case is handled by all users with a trivial helper. This
patch doesn't change any functionality, nor it does add overhead.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Only this member, pins, is defined as "struct ... const *", but the
others in this struct, pinlops, pmxops, confops, etc. are defined as
"const struct ... *".
Swap the "struct pinctrl_pin_desc" and "const" for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This "const" claims the get_function_groups callback never
changes the given num_groups pointer. It is always true
in C language, so not worth mentioning.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes userspace compilation error:
error: unknown type name ‘__virtio16’
__virtio16 tag;
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The <fd979c0132> commit intruduced the perf_event_sysfs_show function
to display the event_str value of an attr in kernel/event/core.c. But
the function returns the value with a newline char.
So, if a event also carries a event.unit file, when printing the counter
data perf tool formatting goes for a spin.
That is, because of the event unit, event name is printed in the newline
because of perf_event_sysfs_show returns with a newline char.
Now fixing perf core will break API, hencing proposing a fix in the perf tool.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1433052383-21802-1-git-send-email-maddy@linux.vnet.ibm.com
[ Add spaces around operators ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Alternative fixes would be:
- calling "gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE)" from the
platform code,
- setting "gic_chip.flags = IRQCHIP_SKIP_SET_WAKE" in the GIC driver
code,
but these were withheld as the GIC hardware doesn't really support
wake-up interrupts.
Fixes: ab82fa7da4 ("gpio: rcar: Prevent module clock disable when wake-up is enabled")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The address for SD0_WP_CD_SEL, SD1_WP_CD_SEL is 0xf8000830,
0xf8000834, respectively.
Each offset address must be prefixed with 0x.
Fixes: add958cee9 "pinctrl: Add driver for Zynq"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removes Vernier Software & Technology devices from the ldusb
driver and the hid_ignore_list table of the usbhid driver in the
Linux tree. These devices will now be supported via the hidraw
driver.
A user space driver for these devices will be found in the
Go! Software Development Kit from Vernier at
http://www.vernier.com/downloads/software-development-kits/go-sdk/.
These devices are also be supported by the LabQuest2 standalone
interface shown at http://www.vernier.com/products/interfaces/labq2/
and the LoggerPro for Linux software shown at
http://www.vernier.com/downloads/logger-pro-linux/.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech M560 is a wireless mouse designed for windows 8 which uses
the unifying receiver.
Compared to a standard one, some buttons (the middle one and the
two ones placed on the side) are bound to a key combination
instead of a generating classic "mouse" button events.
The device shows up as a mouse and keyboard combination: when the middle
button is pressed it sends a key (as keyboard) combination, the same
happens for the two side button. The left/right/wheel work as expected
from a mouse. To complicate things further, the middle button sends
different keys combinations between odd and even presses.
In the "even" press it also sends a left click. But the worst thing
is that no event is generated when the middle button is released.
It is possible to re-configure the mouse sending a command (see function
m560_send_config_command()). After this command the mouse sends some
useful data when the buttons are pressed and/or released.
[jkosina@suse.cz: fix build breakage due to leftover from previous
patch version]
Signed-off-by: Goffredo Baroncelli <kreijack@inwind.it>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename the function extract() to hid_field_extract(), make it external linkage
to allow the use from other modules.
Suggested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Goffredo Baroncelli <kreijack@inwind.it>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.
Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit e5b3b2d9ed ("pinctrl: allows not to define the get_group_pins
operation") allows pin controllers not to register the get_group_pins()
function. However, a side-effect of not registering this function is
that pins are not allocated and potentially multiple devices could
attempt to configure the same pins [1]. Although this problem exists in
the pinctrl core, because only a few devices are impacted by this, fix
this for tegra-xusb by adding the get_group_pins() function.
Please note that in addition to adding the get_group_pins() functions
the pins/lanes for the tegra-xusb also need to be registered when
calling pinctrl_register(). This also allows the current pinmux state
to be viewed by the debugfs node "pinmux-pins" for the tegra-xusb pad
controller.
[1] http://www.spinics.net/lists/linux-gpio/msg05810.html
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The structure tegra_xusb_padctl_group is defined but never used and so
remove this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit a4780adeef ("ARM: 7735/2: Preserve the user r/w register
TPIDRURW on context switch and fork"), arch/arm/ has context switched
the user-writable TLS register, so do the same for compat tasks running
under the arm64 kernel.
Reported-by: André Hentschel <nerv@dawncrow.de>
Tested-by: André Hentschel <nerv@dawncrow.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This driver device one local attribute: vbus.
Describe that in Documentation/ABI/testing/sysfs-platform/twl4030-usb.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB phy should initialize with power-off, and will be powered on
by the USB system when a cable connection is detected.
Having this pm_runtime_get_sync() during probe causes the phy to
*always* be powered on.
Removing it returns to sensible power management.
Fixes: 96be39ab34
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the runtime_suspend callback is running, 'runtime_status'
is always RPM_SUSPENDING, so pm_runtime_suspended() will always
fail.
Similarly while the runtime_resume callback is running
'runtime_status' is RPM_RESUMING, so pm_runtime_active() will
always fail.
So remove these two pointless tests.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A construct like:
if (pm_runtime_suspended(twl->dev))
pm_runtime_get_sync(twl->dev);
is against the spirit of the runtime_pm interface as it
makes the internal refcounting useless.
In this case it is also racy, particularly as 'put_autosuspend'
is used to drop a reference.
When that happens a timer is started and the device is
runtime-suspended after the timeout.
If the above code runs in this window, the device will not be
found to be suspended so no pm_runtime reference is taken.
When the timer expires the device will be suspended, which is
against the intention of the code.
So be more direct is taking and dropping references.
If twl->linkstat is VBUS_VALID or ID_GROUND, then hold a
pm_runtime reference, otherwise don't.
Define "cable_present()" to test for this condition.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In hardware mode we can not use the software demuxer, this means that the
selected scan mask needs to match one of the available scan masks exactly.
It also means that all attached buffers need to use the same scan mask.
Given that when operating in hardware mode there is typically only a single
buffer attached to the device this not an issue. Add a sanity check to make
sure that only a single buffer is attached in hardware mode nevertheless.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For each buffer type specify the supported device modes for this buffer.
This allows us for devices which support multiple different operating modes
to pick the correct operating mode based on the modes supported by the
attached buffers.
It also prevents that buffers with conflicting modes are attached
to a device at the same time or that a buffer with a non-supported mode is
attached to a device (e.g. in-kernel callback buffer to a device only
supporting hardware mode).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All ARMv5 and older CPUs invalidate their caches in the early assembly
setup function, prior to enabling the MMU. This is because the L1
cache should not contain any data relevant to the execution of the
kernel at this point; all data should have been flushed out to memory.
This requirement should also be true for ARMv6 and ARMv7 CPUs - indeed,
these typically do not search their caches when caching is disabled (as
it needs to be when the MMU is disabled) so this change should be safe.
ARMv7 allows there to be CPUs which search their caches while caching is
disabled, and it's permitted that the cache is uninitialised at boot;
for these, the architecture reference manual requires that an
implementation specific code sequence is used immediately after reset
to ensure that the cache is placed into a sane state. Such
functionality is definitely outside the remit of the Linux kernel, and
must be done by the SoC's firmware before _any_ CPU gets to the Linux
kernel.
Changing the data cache clean+invalidate to a mere invalidate allows us
to get rid of a lot of platform specific hacks around this issue for
their secondary CPU bringup paths - some of which were buggy.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The generic RZ CPG compatible value is mandatory, as the driver uses
only this value for matching. Document that this is a fallback that
must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic R-Car Gen2 CPG compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic MSTP gate clocks compatible value is mandatory, as the
driver uses only this value for matching. Document that this is a
fallback that must be present.
Also fix a typo (missing plural "s") in the compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Even if no userspace consumer buffer is attached to the IIO device at
registration we still need to compute the masklength, since it is possible
that a in-kernel consumer buffer is going to get attached to the device at
a later point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
