Without this patch, scsi_show_result prints hostbyte as invalid for statuses
that are not defined in hostbyte_table (when scsi logging is enabled).
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line. Symptoms look like this:
hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:
LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts. So we should use LUN reset,
not target reset.
Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some of new HP laptops have a LED for microphone (or recording) mute,
and it's controlled by GPIO pin 3.
Bind this with the capture switch to turn it on/off properly by the
mixer change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the nomadik include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the w90x900 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the vt8500 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This the definitions for the tegra sdhci driver out of
the tegra include directories, which is the last one
for this platform.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Chris Ball <cjb@laptop.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the sa1100 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jochen Friedrich <jochen@scram.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the netx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the msm include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-arm-msm@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the ep93xx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Axel Lin <axel.lin@gmail.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the at91 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Dan Williams <djbw@fb.com>
Almost each SMP platform defines pen_release to manage booting secondary
CPUs. This of course clashes with the single zImage effort.
Add the pen_release definition to the ARM SMP code, and remove all others.
This should only be used by platforms which lack any kind of CPU power
management...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that all SMP platforms have been converted to use struct
smp_operations, remove the "weak" attribute from the hooks
in smp.c, and make the functions static wherever possible.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the spear13xx platform to use struct smp_operations to provide
its SMP and CPU hotplug operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: spear-devel@list.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the imx6q platform to use struct smp_operations to provide
its SMP and CPU hotplug operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the highbank platform to use struct smp_operations to provide
its SMP and CPU hotplug operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert shmobile SMP platforms to use struct smp_operations to provide
their SMP and CPU hotplug operations.
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert ux500 platforms to use struct smp_operations to provide
their SMP and CPU hotplug operations.
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert MSM SMP platforms to use struct smp_operations to provide
their SMP and CPU hotplug operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert Exynos4 to use struct smp_operations to provide its SMP
and CPU hotplug operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are 32 bit values that come from the user, we need to check for
integer overflows or we could end up allocating a smaller buffer than
expected.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently fifo transfer is started when submitting a transfer
request. Add posibility to defer the fifo transfer and start it
later by calling additional function. This change is backward
compatible, the behaviour of mpc52xx_lpbfifo_submit() is the same
for previous driver users, so there is no need to adapt them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
IFM O2D cameras use special sensor bus interface glue-logic to
connect camera sensors to mpc5200 LocalPlus bus. Add device tree
bindings documentation for it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add common o2d dtsi file to reuse it for other configurations.
Add machine compatible string to mpc5200 simple platform file.
Add dts files for O2D, O2I, O2MNT, O2DNT2, O2D300 and O3DNT boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
WARNING: drivers/built-in.o(.data+0x1e3c8): Section mismatch in
reference from the variable bk_devs to the variable
.devinit.data:bk0_resources
The variable bk_devs references
the variable __devinitdata bk0_resources
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
So add __devinitdata on bk_devs, led_devs & reg_devs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MFD core now takes care of HWIRQ <-> VIRQ mapping, so the helper
ab8500_irq_get_virq() is no longer used by ab8500 subordinate devices
to obtain a Linux wide Virtual IRQ. The AB8500 IRQ controller still
uses it internally though, so we'll just hide it from the rest of the
world by making it static instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ICH chips have their GPIO pins organized in 2 or 3 independent
groups of 32 GPIO pins. It can happen that the ACPI BIOS wants to make
use of pins in one group, preventing the OS to access these. This does
not prevent the OS from accessing the other group(s).
This is the case for example on my Asus Z8NA-D6 board. The ACPI BIOS
wants to control GPIO 18 (group 1), while I (the OS) need to control
GPIO 52 and 53 (group 2) for SMBus multiplexing.
So instead of checking for ACPI resource conflict on the whole I/O
range, check on a per-group basis, and consider it a success if at
least one of the groups is available for the OS to use.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Left over as bitrot from previous changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Further evaluation of the device has yielded some improvements to the
device configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Higher cust_ids have had the device revision field reset so need different
handling of GPIO6.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can read back if the primary IRQ is asserted from the register map,
meaning that we can suppress polling of the interrupt status registers
when only the AoD IRQ domain is asserting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Cc: stable@vger.kernel.org
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch removes the dependency on the usb_serial interface and names
some magic constants
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check for return value of tty_port_tty_get,
since it can return NULL after port hangup that may happen anytime.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6788d7dab6 ("Staging: bcm: Use udelay instead of msleep for
delays in nvm.c") replaces msleep with udelay values. udelay values
of more than 1000 should be replaced by mdelay instead.
This fixes following build error.
ERROR: "__bad_udelay" [drivers/staging/bcm/bcm_wimax.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Cc: Kevin McKinney <klmckinney1@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver reconfigures DRAM size register to 8M (regardless what the
actual size was) once the init has been completed, overwriting the
correct value written during the early init. As a result if the driver
is unloaded and reloaded, the user will be limited to 8M video memory
and may lose some of the available video modes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On embedded systems without a BIOS, the DRAM sizing register is 0 after
the boot, and the driver thinks we have only 1 MB video memory. On such
cases, use the PCI window size for the initial size. This information
is needed only to create the I/O mapping - the driver will later detect
and configure the memory size correctly. Limit the size to 16 MB as it
should be sufficient for all supported video modes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
