The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
it to use generic time and clock events.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6GPY
-----END PGP SIGNATURE-----
Merge tag 'ks8695-time-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
This cleans up the ks8695 timer driver and converts
it to use generic time and clock events.
* tag 'ks8695-time-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ks8695: convert to generic time and clocksource
ARM: ks8695: delete resume hook from timer
ARM: ks8695: use [readl|writel]_relaxed()
ARM: ks8695: merge the timer header into the timer driver
Test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap_fixes_a_3.6rc/20120904110254/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0kV
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.6rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Some hwmod, clockdomain, am335x fixes against v3.6-rc4.
Test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap_fixes_a_3.6rc/20120904110254/
(c7232c9 netfilter: add protocol independent NAT core) introduced a
problem that leads to crashing during boot due to NULL pointer
dereference. It seems that xt_nat calls xt_register_target() before
xt_init():
net/netfilter/x_tables.c:static struct xt_af *xt; is NULL and we crash on
xt_register_target(struct xt_target *target)
{
u_int8_t af = target->family;
int ret;
ret = mutex_lock_interruptible(&xt[af].mutex);
...
Fix this by changing the linking order, to make sure that x_tables
comes before xt_nat.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When running 32-bit pvops-dom0 and a driver tries to allocate a coherent
DMA-memory the xen swiotlb-implementation returned memory beyond 4GB.
The underlaying reason is that if the supplied driver passes in a
DMA_BIT_MASK(64) ( hwdev->coherent_dma_mask is set to 0xffffffffffffffff)
our dma_mask will be u64 set to 0xffffffffffffffff even if we set it to
DMA_BIT_MASK(32) previously. Meaning we do not reset the upper bits.
By using the dma_alloc_coherent_mask function - it does the proper casting
and we get 0xfffffffff.
This caused not working sound on a system with 4 GB and a 64-bit
compatible sound-card with sets the DMA-mask to 64bit.
On bare-metal and the forward-ported xen-dom0 patches from OpenSuse a coherent
DMA-memory is always allocated inside the 32-bit address-range by calling
dma_alloc_coherent_mask.
This patch adds the same functionality to xen swiotlb and is a rebase of the
original patch from Ronny Hegewald which never got upstream b/c the
underlaying reason was not understood until now.
The original email with the original patch is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-02/msg00038.html
the original thread from where the discussion started is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-01/msg00928.html
Signed-off-by: Ronny Hegewald <ronny.hegewald@online.de>
Signed-off-by: Stefano Panella <stefano.panella@citrix.com>
Acked-By: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
While TLB_FLUSH_ALL gets passed as 'end' argument to
flush_tlb_others(), the Xen code was made to check its 'start'
parameter. That may give a incorrect op.cmd to MMUEXT_INVLPG_MULTI
instead of MMUEXT_TLB_FLUSH_MULTI. Then it causes some page can not
be flushed from TLB.
This patch fixed this issue.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Yongjie Ren <yongjie.ren@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit '4cb38750d4': (6849 commits)
bcma: fix invalid PMU chip control masks
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895 bits
libata-acpi: add missing inlines in libata.h
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
...
No one uses it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tracing commands builds an array of trace data
items even when the tracepoint is disabled.
Instead, loop in the tracepoint assignment.
This reduces overhead if tracing is compiled
into the driver but not enabled and slightly
reduces overall driver size as well:
text data bss dec hex filename
114514 6509 48 121071 1d8ef before/iwlwifi.ko
114189 6509 48 120746 1d7aa after/iwlwifi.ko
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wext code checks is the event data is within size limits.
When this check fails a message is logged with violating size.
This patch adds the event id to put us on the right track for
resolving that violation.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a file is stored in ICB (inode), we overwrite part of the file, and
the page containing file's data is not in page cache, we end up corrupting
file's data by overwriting them with zeros. The problem is we use
simple_write_begin() which simply zeroes parts of the page which are not
written to. The problem has been introduced by be021ee4 (udf: convert to
new aops).
Fix the problem by providing a ->write_begin function which makes the page
properly uptodate.
CC: <stable@vger.kernel.org> # >= 2.6.24
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Doing so creates warnings, but the function is internal and
not part of the 802.11 docbooks, so it from kerneldoc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We would traverse the full P2M top directory (from 0->MAX_DOMAIN_PAGES
inclusive) when trying to figure out whether we can re-use some of the
P2M middle leafs.
Which meant that if the kernel was compiled with MAX_DOMAIN_PAGES=512
we would try to use the 512th entry. Fortunately for us the p2m_top_index
has a check for this:
BUG_ON(pfn >= MAX_P2M_PFN);
which we hit and saw this:
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1.2-OVM x86_64 debug=n Tainted: C ]----
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff819cadeb>]
(XEN) RFLAGS: 0000000000000212 EM: 1 CONTEXT: pv guest
(XEN) rax: ffffffff81db5000 rbx: ffffffff81db4000 rcx: 0000000000000000
(XEN) rdx: 0000000000480211 rsi: 0000000000000000 rdi: ffffffff81db4000
(XEN) rbp: ffffffff81793db8 rsp: ffffffff81793d38 r8: 0000000008000000
(XEN) r9: 4000000000000000 r10: 0000000000000000 r11: ffffffff81db7000
(XEN) r12: 0000000000000ff8 r13: ffffffff81df1ff8 r14: ffffffff81db6000
(XEN) r15: 0000000000000ff8 cr0: 000000008005003b cr4: 00000000000026f0
(XEN) cr3: 0000000661795000 cr2: 0000000000000000
Fixes-Oracle-Bug: 14570662
CC: stable@vger.kernel.org # only for v3.5
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As part of this patch:
1. Moved existing tegra phy driver to drivers/USB directory.
2. Added standard USB phy driver APIs to tegra phy driver.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unused power field from struct struct acpi_processor_cx.
[rjw: Modified changelog.]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Driver for the "USB20D" / "USBD" block on BCM6328, BCM6368, BCM6816,
BCM6362, BCM3383, and others.
The hardware block was designed to support networking applications
(direct connection of a home router to a PC), and the endpoint
configuration is fixed.
[ balbi@ti.com : dropped USB_GADGET_DUALSPEED from Kconfig ]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As otg.h is containing lots of phy interface related
stuff, moving all phy interface related stuff to new
file named phy.h
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Part of commit (which patches sound/soc/omap/mcbsp.c file):
8fef626 ARM/ASoC: omap-mcbsp: Remove CLKR/FSR mux configuration code
since the tree where it has been applied did not had the earlier patch:
d0db84e ASoC: omap-mcbsp: Fix 6pin mux configuration
which changed code around omap_mcbsp_6pin_src_mux().
Because of the missing part from 8fef626 the sound/soc/omap/mcbsp.c does
not compile in linux-next.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first payload byte indicates how many IR data bytes are following, not
including itself. The IR data bytes appear in pairs as they represent a
series of 16bit intervals.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Matthieu CASTET adjusted picolcd_debug_out_report() to only operate when
there is an active listener on debugfs for events.
Do the same on the more important picolcd_debug_raw_event() that is
called in interrupt context as opposed to picolcd_debug_out_report()
which happens in whichever context that sends reports to device.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Implement support for picoLCD's CIR header using RC_CORE for decoding
the IR event stream.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Split out all FB related data out of struct picolcd_data into a struct
picolcd_fb_data that is allocated with fb_info. This way fb_info may
cleanly outlive struct picolcd_data for as long as needed for its last
user to drop his reference.
Access to struct picolcd_data is now protected with struct
picolcd_fb_data's lock and tile update reports are only generated
while picolcd_fbdata->picolcd is not NULL and is not marked as failed
(which indicates unplug in progress).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Driver code expects to get access to struct picolcd_data from hiddev
and is not prepared to find a NULL pointer there. Most prominent
candidate to trip on it is picolcd_fb_deferred_io().
Delay removing struct picolcd_data from hiddev until all sub-devices
have been unregistered.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We never modify direct_access_msrs[], msrpm_ranges[],
svm_exit_handlers[] or x86_intercept_map[] at runtime.
Mark them r/o.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We use vmcs_field_to_offset_table[], kvm_vmx_segment_fields[] and
kvm_vmx_exit_handlers[] as lookup tables only -- make them r/o.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We never change emulate_ops[] at runtime so it should be r/o.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
