According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
According to compiler warnings, quite some suspend/resume functions
in platform x86 drivers are not used for CONFIG_PM_SLEEP unset, so
add #ifdefs to prevent them from being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The return value of snd_hda_param_read() is -1 for an error, otherwise
it's the supported power states of a codec.
The supported power states is a 32-bit value. Bit 31 will be set to 1
if the codec supports EPSS, thus making "sup" negative. And the bit
28:5 is reserved as "0".
So a negative value other than -1 shall be further checked.
Please refer to High-Definition spec 7.3.4.12 "Supported Power
States", thanks!
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "Beep Playback Switch" had a different value on left and right
channels (such as muting left but not right, or vice versa), this
could result in the right channel being ignored.
This patch enables beep to be sounding from right channel only, and
also give correct result back to userspace (e g amixer).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to compiler warnings, several suspend/resume functions
in ACPI drivers are not used for CONFIG_PM_SLEEP unset, so add
#ifdefs to prevent them from being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.
Since this can not possibly work, it's better to disable i2c
support entirely on this board.
Without this patch, building davinci_all_defconfig results in:
arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Andrey Porodko <panda@chelcom.ru>
Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.
Without this patch, building tct_hammer_defconfig results in:
net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)
The size of vmlinux increases by 1.78% because of this:
size obj-arm/vmlinux.nobug
text data bss dec hex filename
2108474 116916 55352 2280742 22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
text data bss dec hex filename
2150804 116916 53696 2321416 236c08 obj-arm/vmlinux
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The original code was misported from the X driver,
a) an int went to unsigned int, breaking the downward counting testm code
b) the port did the vco/computed clock bits completely wrong.
This fixes an infinite loop on modprobe on some Dell servers with the G200ER
chipset variant.
Found in internal testing.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Do not leak memory by updating pointer with potentially
NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
omap_rng_suspend and omap_rng_resume are unused if CONFIG_PM is enabled
but CONFIG_PM_SLEEP is disabled. I found this while building all defconfig
files on ARM. It's not clear to me if this is the right solution, but
at least it makes the code consistent again.
Without this patch, building omap1_defconfig results in:
drivers/char/hw_random/omap-rng.c:165:12: warning: 'omap_rng_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:171:12: warning: 'omap_rng_resume' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The newly added dmaengine support in the omap2 nand driver
potentially causes an undefined return value from the
omap_nand_probe function when dmaengine_slave_config
reports an error. Let's handle this by returning the
same error back to the caller.
Without this patch, building omap2plus_defconfig results in:
drivers/mtd/nand/omap2.c: In function 'omap_nand_probe':
drivers/mtd/nand/omap2.c:1154:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
The newly added gpio-em driver marks its em_gio_irq_domain_cleanup
function as __devexit, which would lead to that function being
discarded in case CONFIG_HOTPLUG is disabled. However, the function
is also called by the error handling logic em_gio_probe, which
would cause a jump into a NULL pointer if it was removed from the
kernel or module.
Without this patch, building kzm9d_defconfig results in:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x330): Section mismatch in reference from the function em_gio_probe() to the function .devexit.text:em_gio_irq_domain_cleanup()
The function __devinit em_gio_probe() references
a function __devexit em_gio_irq_domain_cleanup().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
em_gio_irq_domain_cleanup() so it may be used outside an exit section.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.
Without this patch, building exynos_defconfig results in:
arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
This function returns its own error codes instead of normal negative
error codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The higher ptrace restriction levels should be blocking even
PTRACE_TRACEME requests. The comments in the LSM documentation are
misleading about when the checks happen (the parent does not go through
security_ptrace_access_check() on a PTRACE_TRACEME call).
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org # 3.5.x and later
Signed-off-by: James Morris <james.l.morris@oracle.com>
Via-headers are parsed beginning at the first character after the Via-address.
When the address is translated first and its length decreases, the offset to
start parsing at is incorrect and header parameters might be missed.
Update the offset after translating the Via-address to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Within SIP messages IPv6 addresses are enclosed in square brackets in most
cases, with the exception of the "received=" header parameter. Currently
the helper fails to parse enclosed addresses.
This patch:
- changes the SIP address parsing function to enforce square brackets
when required, and accept them when not required but present, as
recommended by RFC 5118.
- adds a new SDP address parsing function that never accepts square
brackets since SDP doesn't use them.
With these changes, the SIP helper correctly parses all test messages
from RFC 5118 (Session Initiation Protocol (SIP) Torture Test Messages
for Internet Protocol Version 6 (IPv6)).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 3a8fc53a (netfilter: nf_ct_helper: allocate 16 bytes for the helper
and policy names) introduced a bug in the SIP helper, the helper name is
sprinted to the sip_names array instead of instead of into the helper
structure. This breaks the helper match and the /proc/net/nf_conntrack_expect
output.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ACPI tables in the Macbook Air 5,1 define a single IOAPIC with id 2,
but the only remapping unit described in the DMAR table matches id 0.
Interrupt remapping fails as a result, and the kernel panics with the
message "timer doesn't work through Interrupt-remapped IO-APIC."
To fix this, check each IOAPIC for a corresponding IOMMU. If an IOMMU is
not found, do not allow IRQ remapping to be enabled.
v2: Move check to parse_ioapics_under_ir(), raise log level to KERN_ERR,
and add FW_BUG to the log message
v3: Skip check if IOMMU doesn't support interrupt remapping and remove
existing check that the IOMMU count equals the IOAPIC count
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Avoid the forcewake overhead when simply retiring requests, as often the
last seen seqno is good enough to satisfy the retirment process and will
be promptly re-run in any case. Only ensure that we force the coherent
seqno read when we are explicitly waiting upon a completion event to be
sure that none go missing, and also for when we are reporting seqno
values in case of error or debugging.
This greatly reduces the load for userspace using the busy-ioctl to
track active buffers, for instance halving the CPU used by X in pushing
the pixels from a software render (flash). The effect will be even more
magnified with userptr and so providing a zero-copy upload path in that
instance, or in similar instances where X is simply compositing DRI
buffers.
v2: Reverse the polarity of the tachyon stream. Daniel suggested that
'force' was too generic for the parameter name and that 'lazy_coherency'
better encapsulated the semantics of it being an optimization and its
purpose. Also notice that gen6_get_seqno() is only used by gen6/7
chipsets and so the test for IS_GEN6 || IS_GEN7 is redundant in that
function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By default CONFIG_DEFAULT_MMAP_MIN_ADDR is 4096 and can also be changed via
/proc/sys/vm/mmap_min_addr if needed.
Quoting Russell King (http://marc.info/?l=linux-arm-kernel&m=134401593807820&w=2):
"4096 is also fine for ARM too. There's not much point in having
defconfigs change it - that would just be pure noise in the config
files."
,so remove CONFIG_DEFAULT_MMAP_MIN_ADDR from the defconfig file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
SPI is also connected on the board, use that instead of I2C as it's much
faster. Also define platform data now the core driver is in mainline.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: fixed build error by inclusion missed header]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
commit be9f4a44e7 (ipv4: tcp: remove per net tcp_sock) added a
selinux regression, reported and bisected by John Stultz
selinux_ip_postroute_compat() expect to find a valid sk->sk_security
pointer, but this field is NULL for unicast_sock
It turns out that unicast_sock are really temporary stuff to be able
to reuse part of IP stack (ip_append_data()/ip_push_pending_frames())
Fact is that frames sent by ip_send_unicast_reply() should be orphaned
to not fool LSM.
Note IPv6 never had this problem, as tcp_v6_send_response() doesnt use a
fake socket at all. I'll probably implement tcp_v4_send_response() to
remove these unicast_sock in linux-3.7
Reported-by: John Stultz <johnstul@us.ibm.com>
Bisected-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@parisplace.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling PMTU discovery can increase the output packet
rate but some users have enough resources and prefer to fragment
than to drop traffic. By default, we copy the DF bit but if
pmtu_disc is disabled we do not send FRAG_NEEDED messages anymore.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
IPVS is missing the logic to update PMTU in routing
for its IPIP packets. We monitor the dst_mtu and can return
FRAG_NEEDED messages but if the tunneled packets get ICMP
error we can not rely on other traffic to save the lowest
MTU.
The following patch adds ICMP handling for IPIP
packets in incoming direction, from some remote host to
our local IP used as saddr in the outer header. By this
way we can forward any related ICMP traffic if it is for IPVS
TUN connection. For the special case of PMTUD we update the
routing and if client requested DF we can forward the
error.
To properly update the routing we have to bind
the cached route (dest->dst_cache) to the selected saddr
because ipv4_update_pmtu uses saddr for dst lookup.
Add IP_VS_RT_MODE_CONNECT flag to force such binding with
second route.
Update ip_vs_tunnel_xmit to provide IP_VS_RT_MODE_CONNECT
and change the code to copy DF. For now we prefer not to
force PMTU discovery (outer DF=1) because we don't have
configuration option to enable or disable PMTUD. As we
do not keep any packets to resend, we prefer not to
play games with packets without DF bit because the sender
is not informed when they are rejected.
Also, change ops->update_pmtu to be called only
for local clients because there is no point to update
MTU for input routes, in our case skb->dst->dev is lo.
It seems the code is copied from ipip.c where the skb
dst points to tunnel device.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Removed the following sparse warnings, wether CONFIG_SYSCTL
is defined or not:
* warning: symbol 'ip_vs_control_net_init_sysctl' was not
declared. Should it be static?
* warning: symbol 'ip_vs_control_net_cleanup_sysctl' was
not declared. Should it be static?
Signed-off-by: Claudiu Ghioc <claudiu.ghioc@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Get rid of the ftp_app pointer and allow applications
to be registered without adding fields in the netns_ipvs structure.
v2: fix coding style as suggested by Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The FTP application indirectly depends on the
nf_conntrack_ftp helper for proper NAT support. If the
module is not loaded, IPVS can resize the packets for the
command connection, eg. PASV response but the SEQ adjustment
logic in ipv4_confirm is not called without helper.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The original xc5000c driver support was based on a beta version of the
firmware, and there were no redistribution rights. Change over to using
the release version, for which freely redistributable firmware can be
found here:
http://kernellabs.com/firmware/xc5000/README.xc5000chttp://kernellabs.com/firmware/xc5000/dvb-fe-xc5000c-4.1.30.7.fw
Thanks to Ramon Cazares from Cresta Technology for making the firmware
available as well as working out the licensing issues.
[mchehab@redhat.com: Fix a merge conflict with the patch that added support
for MODULE_FIRMWARE() macro]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the firmware speedup work for the 5000c as well as the original
xc5000. This cuts firmware load time in half.
Thanks to John Casey at Hauppauge for loaning me a board for testing.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch addresses a couple of cases where I forgot to pop open the
gate when in analog mode (a correlary to fix the change made in patch
1c58d5b4a5fca42dce5428bd79b9405878017735).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver prints out a dotted version number but it's in hex. As a
result, the version doesn't visibly match the filename for the firmware,
and it caused a bunch of confusion while discussing different versions
with the chip manufacturer.
Change the firmware printout to be in decimal.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hack I put in a couple of years ago to avoid clock stretching issues
when talking to the xc5000 worked fine for writes, but intermittently
fails for register reads, because the xc5000 may stretch the clock for
longer between bytes (I was seeing cases of 21 us on the analyzer).
The problem manifested itself as the xc5000 firmware version and PLL
lock register intermittently showing garbage values.
Slow down the i2c bus from 30 KHz to 20 KHz to accommodate.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000c and newer versions of the xc5000a firmware need minor revisions
to their initialization process. Add support for validating the firmware
was properly loaded, as well as checking the init status after initialization.
Based on advice from CrestaTech support as well as xc5000 datasheet v2.3.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's possible for the xc5000 to enter an unknown state such that all
subsequent tuning requests fail. The only way to recover is to reset the
tuner and reload the firmware. This problem was detected after several days
straight of issuing tuning requests every five seconds.
Reset the firmware in the event that the PLL is in an unlocked state. This
solution was provided by the engineer at CrestaTech (the company that acquired
Xceive).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjust the retry timeout and number of retries to speed up xc5000
firmware download. With this change it goes from 4.2 seconds to 2.9.
The net time waited is pretty much the same, but we just poll more
often.
Tested at 250 KHz as well as 30 KHz.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are no cases where a control message is ever sent to the au0828
with an actual buffer defined. Remove the reference to dev->ctrlmsg,
which currently requires us to hold a mutex since it is shared with the
read function.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put a hack in place to speed up the firmware load in the case that the
xc5000 has just been reset. The chip can safely do 400 KHz in this mode,
while in normal operation it can only do 100 KHz.
This reduces the firmware load time from 6.9 seconds to 4.2.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We weren't checking whether the resource was in use before calling
res_free(), so applications which called STREAMOFF on a v4l2 device that
wasn't already streaming would cause a BUG() to be hit (MythTV).
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Reported-by: Jay Harbeston <jharbestonus@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
