Commit graph

589,246 commits

Author SHA1 Message Date
Sascha Hauer
3631c597ca ARM: dts: imx53-qsb: Fix gpio button polarity
The polarity of the gpio buttons is defined to '0' which is
active high. The buttons are active low though which has been verified by
testing it and by looking into the schematics. While at it use
defines rathers than numbers for the key codes.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-03-01 21:40:50 +08:00
Wesley Post
f7c7ac480d [media] gspca: Fix ov519 i2c r/w not working when connected to a xhci host
Fix the ov519 driver not working (unable to talk to the sensor) when
plugged into a xhci host. The root cause here is that uhci/ohci/ehci
hosts typically will send any pending async requests every milli-second
and then go to sleep for the rest if the milli-second, where as xhci hosts
send them immediately, causing things to go too fast for the ov519 bridge.

This commit adds a few delays fixing this.

Signed-off-by: Wesley Post <pa4wdh@xs4all.nl>
[hdegoede@redhat.com: Also add delays to w996Xcf.c, as that needs them too]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2016-03-01 10:40:14 -03:00
Alexandre TORGUE
e78b6555e0 ARM: dts: stm32f429: Add system config bank node
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
2016-03-01 14:38:34 +01:00
Hans de Goede
5c915c6876 [media] bttv: Width must be a multiple of 16 when capturing planar formats
On my bttv card "Hauppauge WinTV [card=10]" capturing in YV12 fmt at max
size results in a solid green rectangle being captured (all colors 0 in
YUV).

This turns out to be caused by max-width (924) not being a multiple of 16.

We've likely never hit this problem before since normally xawtv / tvtime,
etc. will prefer packed pixel formats. But when using a video card which
is using xf86-video-modesetting + glamor, only planar XVideo fmts are
available, and xawtv will chose a matching capture format to avoid needing
to do conversion, triggering the solid green window problem.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2016-03-01 10:36:24 -03:00
Jan Luebbe
c73a1f13d0 ARM: imx_v4_v5_defconfig: Enable initramfs support
This makes it possible to automatically boot-test this defconfig with
kernelci.org.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-03-01 21:32:51 +08:00
Jan Luebbe
7763327dd2 ARM: imx_v4_v5_defconfig: Cleanup imx_v4_v5_defconfig
Regenerate imx_v4_v5_defconfig by running:
make imx_v4_v5_defconfig
- Manually disable EXT2_FS and EXT3_FS
make savedefconfig
mv defconfig arch/arm/configs/imx_v4_v5_defconfig

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-03-01 21:32:46 +08:00
Rob Kramer
33f74b893a watchdog: w83627hf: Added NCT6102D support.
As used in (and tested on) the ASRock IMB-150 board. Implementation is
identical to other NCT chips, just with different registers.

Signed-off-by: Rob Kramer <rob@solution-space.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2016-03-01 14:22:05 +01:00
Romain Izard
28fe80077e ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
Both nodes are required to access NAND Flash memory. Additional
settings will be necessary at the board level to use it.

Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-03-01 13:31:04 +01:00
Nicolas Ferre
b1708b72a0 ARM: dts: at91: sama5d2: add dma properties to UART nodes
The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-03-01 13:31:03 +01:00
Krzysztof Kozlowski
89636adde4 phy: Fix armada375 compile test build on UM
The phy-armada375-usb2 driver uses IOMEM functions so COMPILE_TEST && OF
build failed with:

drivers/built-in.o: In function `armada375_usb_phy_probe':
phy-armada375-usb2.c:(.text+0x121d): undefined reference to
`devm_ioremap_resource'

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:51 +05:30
Yoshihiro Shimoda
b956401699 phy: rcar-gen3-usb2: remove HSUSB registers handling
Since the related driver (CPG/MSSR driver) only manages the first module
clock, this driver should not handle the HSUSB registers. So, this patch
removes the HSUSB registers handling.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Heiko Stuebner
605df8af33 phy: rockchip-usb: add handler for usb-uart functionality
Most newer Rockchip SoCs provide the possibility to use a usb-phy
as passthrough for the debug uart (uart2), making it possible to
for example get console output without needing to open the device.

This patch adds an early_initcall to enable this functionality
conditionally via the commandline and also disables the corresponding
usb controller in the devicetree.

Currently only data for the rk3288 is provided, but at least the
rk3188 and arm64 rk3368 also provide this functionality and will be
enabled later.

On a spliced usb cable the signals are tx on white wire(D+) and
rx on green wire(D-).

The one caveat is that currently the reconfiguration of the phy
happens as early_initcall, as the code depends on the unflattened
devicetree being available. Everything is fine if only a regular
console is active as the console-replay will happen after the
reconfiguation. But with earlycon active output up to smp-init
currently will get lost.

The phy is an optional property for the connected dwc2 controller,
so we still provide the phy device but fail all phy-ops with -EBUSY
to make sure the dwc2 does not try to transmit anything on the
repurposed phy.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Yakir Yang
12df9c5056 dt-bindings: add document for rockchip dp phy
Add dt binding documentation for rockchip display port PHY.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Yakir Yang
fd968973de phy: Add driver for rockchip Display Port PHY
Add phy driver for the Rockchip DisplayPort PHY module. This
is required to get DisplayPort working in Rockchip SoCs.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Shawn Lin
c474a94950 phy: add a driver for the Rockchip SoC internal eMMC PHY
This patch to add a generic PHY driver for ROCKCHIP eMMC PHY.
Access the PHY via registers provided by GRF (general register
files) module.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Shawn Lin
7ed0c9613b Documentation: bindings: add dt documentation for Rockchip eMMC PHY
This patch adds a binding that describes the Rockchip eMMC PHYs
found on Rockchip SoCs eMMC interface.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01 17:13:50 +05:30
Andrzej Hajda
0b6c0ad3cf iommu/mediatek: Fix handling of of_count_phandle_with_args result
The function can return negative value so it should be assigned to signed
variable. The patch changes also type of related i variable to make code
more compact and coherent.

The problem has been detected using patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2016-03-01 12:33:46 +01:00
David Gibson
1dace6c665 powerpc/mm: Clean up memory hotplug failure paths
This makes a number of cleanups to handling of mapping failures during
memory hotplug on Power:

For errors creating the linear mapping for the hot-added region:
  * This is now reported with EFAULT which is more appropriate than the
    previous EINVAL (the failure is unlikely to be related to the
    function's parameters)
  * An error in this path now prints a warning message, rather than just
    silently failing to add the extra memory.
  * Previously a failure here could result in the region being partially
    mapped.  We now clean up any partial mapping before failing.

For errors creating the vmemmap for the hot-added region:
   * This is now reported with EFAULT instead of causing a BUG() - this
     could happen for external reason (e.g. full hash table) so it's better
     to handle this non-fatally
   * An error message is also printed, so the failure won't be silent
   * As above a failure could cause a partially mapped region, we now
     clean this up. [mpe: move htab_remove_mapping() out of #ifdef
     CONFIG_MEMORY_HOTPLUG to enable this]

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 22:04:18 +11:00
David Gibson
27828f98a0 powerpc/mm: Handle removing maybe-present bolted HPTEs
At the moment the hpte_removebolted callback in ppc_md returns void and
will BUG_ON() if the hpte it's asked to remove doesn't exist in the first
place.  This is awkward for the case of cleaning up a mapping which was
partially made before failing.

So, we add a return value to hpte_removebolted, and have it return ENOENT
in the case that the HPTE to remove didn't exist in the first place.

In the (sole) caller, we propagate errors in hpte_removebolted to its
caller to handle.  However, we handle ENOENT specially, continuing to
complete the unmapping over the specified range before returning the error
to the caller.

This means that htab_remove_mapping() will work sanely on a partially
present mapping, removing any HPTEs which are present, while also returning
ENOENT to its caller in case it's important there.

There are two callers of htab_remove_mapping():
   - In remove_section_mapping() we already WARN_ON() any error return,
     which is reasonable - in this case the mapping should be fully
     present
   - In vmemmap_remove_mapping() we BUG_ON() any error.  We change that to
     just a WARN_ON() in the case of ENOENT, since failing to remove a
     mapping that wasn't there in the first place probably shouldn't be
     fatal.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 22:04:18 +11:00
David Gibson
abd0a0e791 powerpc/mm: Clean up error handling for htab_remove_mapping
Currently, the only error that htab_remove_mapping() can report is -EINVAL,
if removal of bolted HPTEs isn't implemeted for this platform.  We make
a few clean ups to the handling of this:

 * EINVAL isn't really the right code - there's nothing wrong with the
   function's arguments - use ENODEV instead
 * We were also printing a warning message, but that's a decision better
   left up to the callers, so remove it
 * One caller is vmemmap_remove_mapping(), which will just BUG_ON() on
   error, making the warning message redundant, so no change is needed
   there.
 * The other caller is remove_section_mapping().  This is called in the
   memory hot remove path at a point after vmemmap_remove_mapping() so
   if hpte_removebolted isn't implemented, we'd expect to have already
   BUG()ed anyway.  Put a WARN_ON() here, in lieu of a printk() since this
   really shouldn't be happening.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 22:04:17 +11:00
David Howells
89053aa9c7 MODSIGN: linux/string.h should be #included to get memcpy()
linux/string.h should be #included in module_signing.c to get memcpy(),
lest the following occur:

    kernel/module_signing.c: In function 'mod_verify_sig':
    kernel/module_signing.c:57:2: error: implicit declaration of function 'memcpy' [-Werror=implicit-function-declaration]
      memcpy(&ms, mod + (modlen - sizeof(ms)), sizeof(ms));
      ^

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
2016-03-01 10:36:07 +00:00
Johan Hovold
537b8a8695 Revert "USB: serial: add Moxa UPORT 11x0 driver"
This reverts commit 0b2b093ad4.

Turns out the MOXA vendor driver was basically just a copy of the
ti_usb_3410_5052 driver. We don't want two drivers for the same chip
even if mxu11x0 had gotten some much needed clean up before merge. So
let's remove the mxu11x0 driver, add support for these Moxa devices to
the TI driver, and then clean that driver up instead.

Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-03-01 11:01:33 +01:00
Yegor Yefremov
c0992d0f54 USB: serial: option: add support for Quectel UC20
Add support for Quectel UC20 and blacklist the QMI interface.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable <stable@vger.kernel.org>
[johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
2016-03-01 11:01:33 +01:00
Daniele Palmas
5deef5551c USB: serial: option: add support for Telit LE922 PID 0x1045
This patch adds support for 0x1045 PID of Telit LE922.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2016-03-01 11:01:33 +01:00
Romain Izard
34ff2dc769 ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.

It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.

There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-03-01 10:47:23 +01:00
Libin Yang
d10a80de04 ALSA: hda - hdmi_find_pcm_slot return value bug fix
hdmi_find_pcm_slot return -EBUSY when not no pcm slot found,
not -ENODEV. So the caller should compare with -EBUSY.

Fixes: a76056f2e5 ('ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug')
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2016-03-01 10:29:21 +01:00
Krzysztof Kozlowski
52e8e59270 ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
After adding cpufreq-dt support to Exynos542x, the Odroid XU3-Lite can
be easily overheated when launching eight CPU-intensive tasks:
	thermal thermal_zone3: critical temperature reached(121 C),shutting down

This seems to be specific to Odroid XU3-Lite board which officially
supports lower frequencies than regular XU3 or XU4. When working at
maximum CPU speed (1800 MHz big and 1300 MHz LITTLE) in warmer place for
longer time, the fan fails to cool down the board and it reaches
critical temperature.

Add CPU cooling to Exynos5422/5800 to fix this issue. When reaching last
interrupt-driven trip-point (70 degrees of Celsius) start passive
cooling in polling mode (slowing CPU by 2 steps). When reaching 85
degrees of Celsius, start slowing even more, down to 600 MHz.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2016-03-01 18:04:00 +09:00
Krzysztof Kozlowski
3b93fc0f2a ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
On Exynos5422 and Exynos5800 we support 12 cpufreq steps (200-1300 MHz) for LITTLE
and 18 steps for big core (200-1700 MHz). Add respective cooling cells.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2016-03-01 18:03:42 +09:00
Krzysztof Kozlowski
65ebf53fbd ARM: dts: exynos: Add cooling levels for Exynos5420 CPUs
On Exynos5420 we support 8 cpufreq steps (600-1300 MHz) for LITTLE and
12 steps for big core (700-1800 MHz). Add respective cooling cells.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2016-03-01 18:03:12 +09:00
Peter Ujfalusi
34b4182ce5 ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
Add hwmod data for the eDMA blocks:
 - TPCC: Third-party channel controller
 - TPTC0: Third-party transfer controller 0
 - TPTC1: Third-party transfer controller 1

The TPCC's clock gating status follows the status of its clock and
power domain. This means that the hwmod code can not directly control
the TPCC enable/disable status.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: rephrased last two sentences of the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2016-03-01 01:55:59 -07:00
Alim Akhtar
6bb8371893 arm64: defconfig: Enable Samsung MFD and related configs
Exynos7 based espresso board uses S2MPS15, a multifunction device.
This patch enables S2MPS1X regulator, pmic-clk and rtc drivers utilized by
the same.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2016-03-01 17:55:03 +09:00
Adam Buchbinder
446957ba51 powerpc: Fix misspellings in comments.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 19:27:20 +11:00
Luis Henriques
95442c64de powerpc/ps3: gelic_udbg: use struct udphdr from <linux/udp.h>
Instead of defining a local version of struct udphdr use the standard
definition from <linux/udp.h>.

The 'src' field is named 'source' in the <linux/udp.h> definition.

Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 19:27:20 +11:00
Luis Henriques
0336c8cd4d powerpc/ps3: gelic_udbg: use struct iphdr from <linux/ip.h>
Instead of defining a local version of struct iphdr use the standard
definition from <linux/ip.h>.

Several fields in the <linux/ip.h> definition have different names:
 - proto -> protocol
 - src -> saddr
 - dest -> daddr
 - total_length -> tot_len
 - checksum -> check

Also, 'ver_len' is composed by 'version' and 'ihl' in <linux/ip.h>.

Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 19:27:20 +11:00
Luis Henriques
e9aaa6d1ab powerpc/ps3: gelic_udbg: use struct vlan_hdr from <linux/if_vlan.h>
Instead of defining the local struct vlantag use the standard definition
of vlan_hdr from <linux/if_vlan.h>.

The fields in the <linux/if_vlan.h> definition have different names:
 - vlan -> h_vlan_TCI
 - subtype -> h_vlan_encapsulated_proto

While there, use also the ETH_P_IP macro instead of an hard-coded 0x0800
value.

Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 19:27:20 +11:00
Luis Henriques
497abcf6af powerpc/ps3: gelic_udbg: use struct ethhdr from <linux/if_ether.h>
Instead of defining a local version of struct ethhdr use the standard
definition from <linux/if_ether.h>.

The fields in the <linux/if_ether.h> definition have different names:
 - dest -> h_dest
 - src -> h_source
 - type -> h_proto

While there, use a few other standard functions/macros:
 - eth_broadcast_addr (instead of a memset)
 - ETH_ALEN
 - ETH_P_8021Q

Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-01 19:27:20 +11:00
Lucas Stach
411b0336cf drm/imx: only enable vblank IRQs when needed
The vblank IRQ is only needed to trigger page flip work, so we
might as well disable it when there is no work to do.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:41 +01:00
Lucas Stach
17a8d08df1 drm/imx: implement fence sync
If the FB is backed by a GEM object with an dma-buf attached
we need to wait for any pending fences to signal before executing
the page flip.

The implementation is straight forward by deferring the flip to
a workqueue in that case.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:40 +01:00
Lucas Stach
0a7ad343c8 drm/imx: keep GEM object referenced as long as scanout is active
The DRM core only references the currently queued/active framebuffer.
So there is a period of time where the flip is not completed, but
the GEM object backing the FB is already unreferenced and could be
destroyed if userspace closes its handle.

Make sure to keep a reference to the GEM object until the flip is
actually executed clean things up in a worker running behind the
flip execution.

Also move the page flip event into the context of this worker, so
it gets cleaned up automatically.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:40 +01:00
Lucas Stach
0bfc2b3d01 drm/imx: track flip state explicitly
Start tracking the flip state explicitly, as opposed to inferring
it from the presence if a new FB. This is a preparatory step to
introduce an new immediate state, where we can wait for a fence to
signal.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:40 +01:00
Lucas Stach
f5dca1608b drm/imx: don't touch primary fb on pageflip
The core already does the correct replacemet if the driver
page flip function returns without an error, so there is no
need to do it here.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:39 +01:00
Liu Ying
beec8ec0bd drm/imx: ipuv3 plane: Replace dev_info with dev_dbg if a plane's CRTC changes
This patch changes the dev_info() call to dev_dbg() in ipu_plane_update()
to print out the information that a plane's CRTC is changed, because this
kind of information is only useful for debugging.

Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:39 +01:00
Philipp Zabel
86bdb09f04 gpu: ipu-v3: ipu-dc: Simplify display controller microcode setup
This cleans up the display controller microcode setup in ipu_dc_init_sync
a little bit. The microcode template words for DI0 and DI1 are properly
separated to avoid a clash when DI1 is active in interlaced mode at the
same time as DI0 in non-interlaced mode.
A comment is added to explain the meaning of the sync counter.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:38 +01:00
Philipp Zabel
1645061679 drm/rockchip: remove rockchip_drm_encoder_get_mux_id
It is replaced by drm_of_encoder_active_endpoint_id.

Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Yakir Yang <ykk@rock-chips.com>
[for dw_hdmi-rockchip]
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:38 +01:00
Philipp Zabel
53141e42cf drm/imx: remove imx_drm_encoder_get_mux_id
It is replaced by drm_of_encoder_active_port_id.

Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-03-01 08:33:38 +01:00
David S. Miller
397d1533b6 sparc64: Fix sparc64_set_context stack handling.
Like a signal return, we should use synchronize_user_stack() rather
than flush_user_windows().

Reported-by: Ilya Malakhov <ilmalakhovthefirst@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 00:25:32 -05:00
David S. Miller
22be3b1055 sparc32: Add -Wa,-Av8 to KBUILD_CFLAGS.
Binutils used to be (erroneously) extremely permissive about
instruction usage.  But that got fixed and if you don't properly tell
it to accept classes of instructions it will fail.

This uncovered a specs bug on sparc in gcc where it wouldn't pass the
proper options to binutils options.

Deal with this in the kernel build by adding -Wa,-Av8 to KBUILD_CFLAGS.

Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 00:24:04 -05:00
Caesar Wang
7ea38c6c36 thermal: rockchip: fix the tsadc sequence output on rk3228/rk3399
As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.

Fixes: commit
b0d7033 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e "thermal: rockchip: Support the RK3228 SoCs in thermal driver"

Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2016-02-29 21:06:39 -08:00
Caesar Wang
952418a34f thermal: rockchip: the rename compatibles for rockchip SoCs
This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.

Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2016-02-29 21:05:39 -08:00
Elaine Zhang
1d37a037dd thermal: rockchip: fix calculation error for code_to_temp
the calculation use a global table, not their own table.
so adapt the table to the correct one.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2016-02-29 21:04:35 -08:00