WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh.
Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S.
Also add _11S as post-fix to each of WMI_SERVICE_MESH and
WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh.
This will help users to distinguish 11s Mesh from non 11s Mesh.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx vring needs to be enlarged to get better
performance for traffic over 2Gbps.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case there are multiple WMI commands with the same reply_id,
the following scenario can occur:
- Driver sends the first command to the device
- The reply didn’t get on time and there is timeout
- Reply_id, reply_buf and reply_size are set to 0
- Driver sends second wmi command with the same reply_id as the first
- Driver sets wil->reply_id
- Reply for the first wmi command arrives and handled by wmi_recv_cmd
- As its ID fits the reply_id but the reply_buf is not set yet it is
handled as a reply with event handler, and WARN_ON is printed
This patch guarantee atomic setting of all the reply variables and
prevents the above scenario.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil_tx_vring locks the vring_tx_data lock before accessing the TX
vring to check if it is enabled and valid for use.
In case of quick disconnect / connect events for the same station,
spin_lock(&txdata->lock) can be called during the lock initialization
in the vring init function.
To prevent such a race, the TX vrings spin lock should be initialized
once during wil6210 driver initialization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe719 ("mmc: pxamci: fix read-only gpio detection polarity")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Tested-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch fixes the calculation of pcc_chan for non-zero id.
After the compiler ignores the (unsigned long) cast the
pcc_mbox_channels pointer is type-cast and then the type-cast
offset is added which results in address outside of the range
leading to the kernel crashing.
We might add braces and make it:
pcc_chan = (struct mbox_chan *)
((unsigned long) pcc_mbox_channels +
(id * sizeof(*pcc_chan)));
but let's go with array approach here and use id as index.
Tested on Juno board.
Signed-off-by: Alexey Klimov <alexey.klimov@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
They're both running only when ->edac_check is initialized so remove
that check from the workqueue function itself. Synchronize/generalize
the ->op_state check between the two.
Kill useless comments, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
We use the ->edac_check function pointers to determine whether we need
to setup a polling workqueue. However, the destroy path is not balanced
and we might try to teardown an unitialized workqueue.
Balance init and destroy paths by looking at ->edac_check in both cases.
Set op_state to OP_OFFLINE *before* destroying anything.
Reported-by: Zhiqiang Hou <Zhiqiang.Hou@freescale.com>
Cc: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
i2c3 and uart4 are available on the GPIO header. Though these pins only
have this one special function, the user may choose to use them as GPIOs
instead.
Since our policy is not to choose what function to present on the GPIO
headers of development boards, remove them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable ARM big-endian mode on mach-imx. This requires adding some
byte swapping in the debug functions (which otherwise hang forever)
and of course the secondary core bringup.
Tested (on top of 4.4) on i.MX6 HummingBoard quad-core (IMX6Q).
The patch is pretty much as suggested by Arnd Bergmann, thanks!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of __raw_*, define imx_* to *_relaxed and use those.
Using imx_* was requested by Arnd because *_relaxed tends to
indicate that the code was carefully reviewed to not require
any synchronisation and otherwise be safe, which isn't the
case here with the automatic conversion.
The conversion itself was done using the following spatch
(since that automatically adjusts the coding style unlike
a simple search&replace).
@@
expression E1, E2;
@@
-__raw_writel(E1, E2)
+imx_writel(E1, E2)
@@
expression E1, E2;
@@
-__raw_writew(E1, E2)
+imx_writew(E1, E2)
@@
expression E1;
@@
-__raw_readl(E1)
+imx_readl(E1)
@@
expression E1;
@@
-__raw_readw(E1)
+imx_readw(E1)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Fix the code to fetch and decode the whole 32-bit instruction. This
only really matters with the `noulri' kernel parameter as all microMIPS
processors are supposed to have all the hardware registers we support.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the regular MIPS instruction set RDHWR is encoded with the SPECIAL3
(011111) major opcode. Therefore it cannot trigger the CpU (Coprocessor
Unusable) exception, and certainly not for coprocessor 0, as the opcode
does not overlap with any of the older ISA reservations, i.e. LWC0
(110000), SWC0 (111000), LDC0 (110100) or SDC0 (111100). The closest
match might be SDC3 (111111), possibly causing a CpU #3 exception,
however our code does not handle it anyway. A quick check with a MIPS I
and a MIPS III processor:
CPU0 revision is: 00000220 (R3000)
CPU0 revision is: 00000440 (R4400SC)
indeed indicates that the RI (Reserved Instruction) exception is
triggered. It's only LL and SC that require emulation in the CpU #0
exception handler as they reuse the LWC0 and SWC0 opcodes respectively.
In the microMIPS instruction set RDHWR is mandatory and triggering the
RI exception is required on unimplemented or disabled register accesses.
Therefore emulating the microMIPS instruction in the CpU #0 exception
handler is not required either.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These three cases let clk_register() fail. They should be considered
as error messages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The core->parents is a cache to save expensive clock parent look-ups.
It will be filled as needed later. We do not have to do it here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop the "if (!core->parents)" case and refactor the function a bit
because core->parents is always allocated. (Strictly speaking, it is
ZERO_SIZE_PTR if core->num_parents == 0, but such a case is omitted
by the if-conditional above.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, __clk_core_init() allows failure of the kcalloc() for the
core->parents. So, clk_fetch_parent_index() and __clk_init_parent()
also try to allocate core->parents in case it has not been allocated
yet. Scattering memory allocation here and there makes things
complicated.
Like other clk_core members, allocate core->parents in clk_register()
and let it fail in case of memory shortage. If we cannot allocate
such a small piece of memory, the system is already insane. There is
no point to postpone the memory allocation.
Also, allocate core->parents regardless of core->num_parents. We want
it even if core->num_parents == 1 because clk_fetch_parent_index()
might be called against the clk_core with a single parent.
If core->num_parents == 0, core->parents is set to ZERO_SIZE_PTR. It
is harmless because no access happens to core->parents in such a case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now, the clock parent is not "struct clk *", but "struct clk_core *".
Of course, the size of a pointer is always same, but strictly speaking,
sizeof(struct clk *) should be sizeof(struct clk_core *) here.
This mismatch happened when we split the structure into struct clk
and struct clk_core. For the potential possibility of future renaming,
sizeof(*core->parents) would be better.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This if-block has been here since the introduction of the common
clock framework. Now no clock drivers are statically initialized.
core->parent is always NULL at this point. Drop the redundant
check and the confusing comment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now this function takes clk_core as its argument. __clk_core_init()
would be more suitable for the name of this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The argument clk_user is used only for the clk_user->core. The rest
of this function only takes care of clk_core.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "struct device *dev" is not used at all in this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Pull libnvdimm fixes from Dan Williams:
"1/ Fixes to the libnvdimm 'pfn' device that establishes a reserved
area for storing a struct page array.
2/ Fixes for dax operations on a raw block device to prevent pagecache
collisions with dax mappings.
3/ A fix for pfn_t usage in vm_insert_mixed that lead to a null
pointer de-reference.
These have received build success notification from the kbuild robot
across 153 configs and pass the latest ndctl tests"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
phys_to_pfn_t: use phys_addr_t
mm: fix pfn_t to page conversion in vm_insert_mixed
block: use DAX for partition table reads
block: revert runtime dax control of the raw block device
fs, block: force direct-I/O for dax-enabled block devices
devm_memremap_pages: fix vmem_altmap lifetime + alignment handling
libnvdimm, pfn: fix restoring memmap location
libnvdimm: fix mode determination for e820 devices