The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We dereference "eaction->event" inside the call to drm_send_event_locked()
so should hold off on setting it to NULL until afterward.
Fixes: fb740cf249 ("drm: Create drm_send_event helpers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160128090646.GA5824@mwanda
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I think this limit was added when CSA with multiple interfaces wasn't
working yet. It should no longer be necessary
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add F81866 GPIO supports
Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.
Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
The control method is the same with F7188x, but we should care the address
of GPIO8x.
GPIO address is below:
GPIO0x based: 0xf0
GPIO1x based: 0xe0
GPIO2x based: 0xd0
GPIO3x based: 0xc0
GPIO4x based: 0xb0
GPIO5x based: 0xa0
GPIO6x based: 0x90
GPIO7x based: 0x80
GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt-parent property is not needed as it is inherited from
the parent bus and in the case of the CAAM node actively points to
the wrong interrupt controller (GIC instead of GPC). This leads to
the CAAM IRQs not getting unmasked at the GPC level, leaving them
unable to wake the CPU from wait mode, potentially impacting
performance of the CAAM unit when CPUidle is enabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like how pci.c exposes hif ops for the bus specific operation,
expose similar hif ops table for ahb with all required functions
linked to it. Many ath10k_pci_* functions are reused here in hif ops
table. If something is not sharable, new functions are added for ahb
and linked to hif ops table.
Finally, make ath10k_ahb_probe/remove() to perform what is expected
out of it.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add function to gather resources required for qca4019 to operate
(memory, irq, dma setting, clock init , rest control init) and
function release those resources when it's not needed.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add irq related functions to register,handle,release,disable interrupt.
qca4019 supports msi interrupt, but it has the problem. Until the issue
gets sorted out, only legacy interrupt model is enabled and used.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add function to perform chip halt sequence and function to halt axi
bus in ahb module. Mainly used in the scenario like driver unload.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To perform reset on qca4019 wifi, multiple reset lines needs
to be toggled in a sequence with help of reset controller support
in the kernel. This patch adds functions to reset control init/deinit
and release reset.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pre qca4019 chipsets has/uses internal clock generator for
the operation. But, qca4019 uses external clocks supplied from
outside of target (ie, outside of wifi core). Three different clocks
(cmd clock, ref clock, rtc clock) comes into picture in qca4019.
All those clocks needs to configured with help of global clock
controller (gcc) to make qca4019 functioning.
Add functions for clock init/deinit, clock enable/disable in ahb.
This is just a preparation, functions added in this patch will be
used in later patches.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca4019 deals with below register memory region to control the clock,
reset, etc.
- Memory to control wifi core
- gcc (outside of wifi)
- tcsr (outside of wifi)
Add new helper functions to perform read/write in above registers
spaces. Actual ioremap for above registers are done in later patch.
Struct ath10k_ahb is introduced to maintain ahb specific info and
memory this struct will be allocated in the continuation of struct
ath10k_pci (again, memory ath10k_ahb is allocated in the later patch).
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New register table is added for qca4019 to tell about it's
register mapping details.
Nothing much other than this.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca4019 uses ahb instead of pci where it slightly differs in device
enumeration, clock control, reset control, etc. Good thing is that
ahb also uses copy engine for the data transaction. So, the most of
the stuff implemented in pci.c/ce.c are reusable in ahb case too.
Device enumeration in ahb case comes through platform driver/device
model. All resource details like irq, memory map, clocks, etc for
qca4019 can be fetched from of_node of platform device.
Simply flow would look like,
device tree => platform device (kernel) => platform driver (ath10k)
Device tree entry will have all qca4019 resource details and the same
info will be passed to kernel. Kernel will prepare new platform device
for that entry and expose DT info to of_node in platform device.
Later, ath10k would register platform driver with unique compatible name
and then kernels binds to corresponding compatible entry & calls ath10k
ahb probe functions. From there onwards, ath10k will take control of it
and move forward.
New bool flag CONFIG_ATH10K_AHB is added in Kconfig to conditionally
enable ahb support in ath10k. On enabling this flag, ath10k_pci.ko
will have ahb support. This patch adds only basic skeleton and few
macros to support ahb in the context of qca4019.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the code present in ath10k_pci_{probe|remove} are reusable
in ahb case too. To avoid code duplication, move reusable code to
new functions. Later, those new functions can be called from ahb
module's probe and exit functions.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_read32/write32() does work more specific to
PCI by ensuring pci wake/sleep for every read and write.
There is a plan to use most of stuff available in pci.c
(irq stuff, copy engine, etc) for AHB case. Such kind
of pci wake/sleep for every read/write is not required
in AHB case (qca4019). All those reusable areas in pci.c
and ce.c calls ath10k_pci_read32/write32() for low level
read and write.
In fact, ath10k_pci_read32/write32() should do what it does
today for PCI case. But for AHB, it has to do differently.
To make ath10k_pci_read32/write32() more generic, new function
pointers are added in ar_pci for the function which does
operation more close to the bus. Later, corresponding bus
specific read and write function will be mapped to that.
ath10k_pci_read32/write32() are changed to call directly
those function pointers without worrying which bus underlying
to it. Also, the function to get number of bank is changed
in the same way.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of static functions present in pci.c file are reusable
in ahb (qca4019) case. Remove static word for those reusable
functions and have those function prototype declaration in
pci.h file. So that, pci.h header file can be included in
ahb module and reused. There is no functionality changes done
in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.
This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes the code easier to extend and re-use.
While at it fix _warn to _err. Other than that
there are no functional changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.
Primary function of this is improved MU-MIMO
performance with multiple clients.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commond 'cat /sys/devices/soc0/revision' can
show correct soc version information.
"unknow revision" message in imx_print_silicon_rev()
will never work for digprog.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wrong pointer is passed to the ioumap function in the cleanup path
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,input-wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
ALSA dummy driver can switch the timer backend between system timer
and hrtimer via its hrtimer module option. This can be also switched
dynamically via sysfs, but it may lead to a memory corruption when
switching is done while a PCM stream is running; the stream instance
for the newly switched timer method tries to access the memory that
was allocated by another timer method although the sizes differ.
As the simplest fix, this patch just disables the switch via sysfs by
dropping the writable bit.
BugLink: http://lkml.kernel.org/r/CACT4Y+ZGEeEBntHW5WHn2GoeE0G_kRrCmUh6=dWyy-wfzvuJLg@mail.gmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NFS_LAYOUT_RETURN_BEFORE_CLOSE is being used to signal that a
layoutreturn is needed, either due to a layout recall or to a
layout error. Rename it to NFS_LAYOUT_RETURN_REQUESTED in order
to clarify its purpose.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Driver for the BYD BTP10463 touchpad, found in PC Specialist `Lafite'
laptops. This patch sends the magic command sequence which causes the
touchpad to stream intellimouse-style packets.
Gestures are detected inside the touchpad, and exposed as special
values in the Z component of each packet - absolute coordinates are
not supported, even in the Windows driver. At present, this supports
two-finger vertical and horizontal scrolling, and provides the
framework to expose the other gestures it can recognize.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Warn if tty_audit_buf use is attempted after tty_audit_exit() has
already freed it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data read from another tty may be relevant to the action of
the TIOCSTI ioctl; log the audit buffer immediately.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Audit is unlikely to be enabled; check first to exit asap.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first-use tty audit buffer allocation is a potential race
amongst multiple attempts at 'first-use'; only one 'winner' is
acceptable.
The successful buffer assignment occurs if tty_audit_buf == NULL
(which will also be the return from cmpxchg()); otherwise, another
racer 'won' and this buffer allocation is freed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tty_audit_exit() is called from do_exit(), the process is
single-threaded. Since the tty_audit_buf is only shared by threads
of a process, no other thread can be concurrently accessing the
tty_audit_buf during or after tty_audit_exit().
Thus, no other thread can be holding an extra tty_audit_buf reference
which would prevent tty_audit_exit() from freeing the tty_audit_buf.
As that is the only purpose of the ref counting, remove the reference
counting and free the tty_audit_buf directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty audit buffer is allocated at first use and not freed until
the process exits. If tty audit is turned off after the audit buffer
has been allocated, no effort is made to release the buffer.
So re-checking if tty audit has just been turned off when tty audit
was just on is false optimization; the likelihood of triggering this
condition is exceedingly small.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The audit_tty and audit_tty_log_passwd fields are actually bool
values, so merge into single memory location to access atomically.
NB: audit log operations may still occur after tty audit is disabled
which is consistent with the existing functionality
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_t instead of separate major/minor fields to track tty
audit buffer association.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_audit_push() and tty_audit_push_current() perform identical
tasks; eliminate the tty_audit_push() implementation and the
tty_audit_push_current() name.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In canonical read mode, each line read and logged is pushed separately
with tty_audit_push(). For all single-threaded processes and multi-threaded
processes reading from only one tty, this patch has no effect; the last line
read will still be the entry pushed to the audit log because the tty
association cannot have changed between tty_audit_add_data() and
tty_audit_push().
For multi-threaded processes reading from different ttys concurrently,
the audit log will have mixed log entries anyway. Consider two ttys
audited concurrently:
CPU0 CPU1
---------- ------------
tty_audit_add_data(ttyA)
tty_audit_add_data(ttyB)
tty_audit_push()
tty_audit_add_data(ttyB)
tty_audit_push()
This patch will now cause the ttyB output to be split into separate
audit log entries.
However, this possibility is equally likely without this patch:
CPU0 CPU1
---------- ------------
tty_audit_add_data(ttyB)
tty_audit_add_data(ttyA)
tty_audit_push()
tty_audit_add_data(ttyB)
tty_audit_push()
Mixed canonical and non-canonical reads have similar races.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lock_task_sighand() is for situations where the struct task_struct*
may disappear while trying to deref the sighand; this never applies
to 'current'.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty audit buffer used to audit/record tty input is allocated on
the process's first call to tty_audit_add_data(), and not freed until
the process exits. On each call to tty_audit_add_data(), the current
tty is compared (by major:minor) with the last tty associated with
the audit buffer, and if the tty has changed the existing data is
logged to the audit log. The audit buffer is then re-associated with
the new tty.
Currently, the audit buffer is immediately associated with the tty;
however, the association must be re-checked when the buffer is locked
prior to copying the tty input. This extra step is always necessary,
since a concurrent read of a different tty by another thread of the
process may have used the buffer in between allocation and buffer
lock.
Rather than associate the audit buffer with the tty at allocation,
leave the buffer initially un-associated (null dev_t); simply let the
re-association check also perform the initial association.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty termios bits cannot change while n_tty_read() is in the
i/o loop; the termios_rwsem ensures mutual exclusion with termios
changes in n_tty_set_termios(). Check L_ICANON() directly and
eliminate icanon parameter.
NB: tty_audit_add_data() => tty_audit_buf_get() => tty_audit_buf_alloc()
is a single path; ie., tty_audit_buf_get() and tty_audit_buf_alloc()
have no other callers.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty audit never logs pty master reads, but packet mode only works for
pty masters, so tty_audit_add_data() was never logging packet mode
anyway.
Don't audit packet mode data. As those are the lone call sites, remove
tty_put_user().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reads from pty masters are not logged; early-out before taking
locks.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>