Refactor the control of measurement and standby modes for the sensor.
Instead of directly writing to the register, encapsulate this operation
in a dedicated function that handles enabling and disabling measurement.
This approach will reduce code duplication wherever sensor configuration
changes are required. In subsequent patches, measurement mode will be
set to standby as part of this process.
Additionally, simplify the control mask to include only the measurement
bit. The sleep bit governs a different behavior—putting the sensor into
sleep mode, not just standby for configuration—and is currently unused.
Therefore, there's no need to include both the sleep and measurement
bits in the same mask.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250702230819.19353-3-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Setup regmap cache to cache register configuration, reducing bus traffic
for repeated accesses to non volatile registers.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250702230819.19353-2-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MediaTek MT6373 is a PMIC found on MT8196/MT6991 board designs
and communicates with the SoC over SPMI.
This PMIC integrates an Auxiliary ADC (AUXADC) which has a grand
total of 54 channels, of which usually only 9 are used as this
is usually paired with MT6363 on the same board.
For the Auxiliary ADC part, this reuses the same register layout
as the MT6363 PMIC, but exposes only a subset of the ADC chans.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MediaTek MT6363 is a PMIC found on MT8196/MT6991 board designs
and communicates with the SoC over SPMI.
This PMIC integrates an Auxiliary ADC (AUXADC) which has a grand
total of 54 ADC channels: 49 PMIC-internal channels, 2 external
NTC thermistor channels and 2 generic ADC channels (mapped to 7
PMIC ADC external inputs).
To use a generic ADC channel it is necessary to enable one of
the PMIC ADC inputs at a time and only then start the reading,
so in this case it is possible to read only one external input
for each generic ADC channel.
Due to the lack of documentation, this implementation supports
using only one generic ADC channel, hence supports reading only
one external input at a time.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to add support for new PMICs, add a `vref_mv`
member to struct mtk_pmic_auxadc_info and use it in place of
the AUXADC_VOLT_FULL definition.
As a consequence, the definition was also removed.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation for adding support for the AUXADC block found in
the MT6363 PMIC, add the ready register index and mask to the
mtk_pmic_auxadc_chan structure, populate those in the channel
description for all of the already supported SoCs and make use
of them in the .read_imp() callbacks.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a compatible and channel bindings for MediaTek's MT6373 PMIC,
featuring an Auxiliary ADC IP with 15 ADC channels for external
(SoC) temperatures and external voltage inputs.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a compatible and channel bindings for MediaTek's MT6363 PMIC,
featuring an Auxiliary ADC IP with 15 ADC channels used for both
internal temperatures and voltages and for external voltage inputs.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703141146.171431-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI offload support to the ad_sigma_delta module.
When the SPI controller has SPI offload capabilities, the module will
now use that for buffered reads instead of the RDY interrupt trigger.
Drivers that use the ad_sigma_delta module will have to opt into this
by setting supports_spi_offload since each driver will likely need
additional changes before SPI offload can be used. This will allow us
to gradually enable SPI offload support for each driver.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-11-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_optimize_message() to improve the performance of buffered reads.
By setting up the SPI message and pre-optimizing it in the buffer
postenable callback, we can reduce overhead during each sample read.
A rough estimate shows that this reduced the CPU usage of the interrupt
handler thread from 22% to 16% using an EVAL-AD4112ARDZ board on a
DE10-Nano (measuring a single channel at the default 6.2 kHz sample
rate).
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-8-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor code to set the read address in a separate function.
This code is already duplicated twice and we will need to use it a third
time in a later commit.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-7-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop linux/iio/sysfs.h since it is unused and replace linux/kernel.h
with more explicit headers. There are a couple of other headers added
weren't covered by kernel.h, like linux/gpio/consumer.h that are added
since the module makes use of those APIs as well.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-6-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the BITS_TO_BYTES() macro instead of dividing by 8 to convert bits
to bytes.
This makes it more obvious what unit conversion is taking place.
In one instance, we also avoid the temporary assignment to a variable
as it was confusing that reg_size was being used with two different
units (bits and bytes).
scan_type is factored out to reduce line wrapping.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-5-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use sizeof() instead of hardcoding the size of the timestamp in the
ALIGN() macro. This makes it a bit more obvious what the intention of
the code is.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-4-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace uint8_t with u8 in the ad_sigma_delta driver.
Technically, uint8_t comes from the C standard library, while u8 is a
Linux kernel type. Since we don't use the C standard library in the
kernel, we should use the kernel types instead.
There is also one instance where int64_t is replaced with s64.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-3-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix overallocating the size of the scan buffer by converting bits to
bytes. The size is meant to be in bytes, so scanbits needs to be
divided by 8.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-1-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Documentation/filesystems/sysfs.rst mentions that show() should only
use sysfs_emit() or sysfs_emit_at() when formating the value to be
returned to user space. So replace scnprintf() with sysfs_emit().
Signed-off-by: Chelsy Ratnawat <chelsyratnawat2001@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://patch.msgid.link/20250701154720.54276-1-chelsyratnawat2001@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change the dlhl60d driver to use individual chip info structures instead
of an array. This reduces the verbosity of the code. Also, the data is
now const as it should have been in the first place.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250628-iio-const-data-24-v2-1-1c90073d1323@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the calibscale field from struct cm3232_als_info to struct
cm3232_chip. The chip info struct is supposed to be const while the
driver data struct should contain mutable fields. Since calibscale
is a mutable field, it should be in the driver data struct.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250628-iio-const-data-20-v1-1-2bf90b03f9f1@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change the adis16400 driver to use individual chip info structures
instead of an array. This reduces the verbosity of the code. Also, the
data is now const as it should have been in the first place.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250628-iio-const-data-17-v1-1-a215ebb653ec@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7768-1 has a different -3db frequency multiplier depending on
the filter type configured. The cutoff frequency also varies according
to the current ODR.
Add a readonly low pass -3dB frequency cutoff attribute to clarify to
the user which bandwidth is being allowed depending on the filter
configurations.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/804d66f1858014d7278aec3344d81c223661e878.1749569957.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change the ad7124 driver to use individual chip info structures instead
of an array. This reduces the verbosity of the code. Also, the data is
now const as it should have been in the first place.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250628-iio-const-data-5-v1-1-9e56c2f77979@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add const qualifier to struct vcnl3020_property
vcnl3020_led_current_property. This is read-only data so it can be made
const.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250628-iio-const-data-25-v1-2-5d99cf17790e@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Randy reports that amdgpu fails to compile with the following error:
ERROR: modpost: "pm_hibernate_is_recovering" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This happens because pm_hibernate_is_recovering() is only compiled when
CONFIG_PM_SLEEP is set. Add a stub for it so that drivers don't need
to depend upon CONFIG_PM.
Cc: Samuel Zhang <guoqing.zhang@amd.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/dri-devel/CAJZ5v0h1CX+aTu7dFy6vB-9LM6t5J4rt7Su3qVnq1xx-BFAm=Q@mail.gmail.com/T/#m2b9fe212b35fde11d58fcbc4e0727bc02ebba7b0
Fixes: c2aaddbd2d ("PM: hibernate: add new api pm_hibernate_is_recovering()")
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20250712233715.821424-1-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250707-gpiochip-set-rv-gpio-round4-v1-10-35668aaaf6d2@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Acked-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250707-gpiochip-set-rv-gpio-round4-v1-5-35668aaaf6d2@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
One of the users of global GPIO numbers in the kernel are the debugfs
callbacks in GPIO drivers. Before converting any custom .dbg_show()
callbacks in individual modules, let's first make GPIO core stop using
GPIO base in debugfs output. Use hardware offsets instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250707141313.73169-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert the traffic_class in GRH to a DSCP value as required by the HW.
Fixes: e095405b45 ("RDMA/mana_ib: Modify QP state")
Signed-off-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://patch.msgid.link/1752143085-4169-1-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add an option to create CQ using external memory instead of allocating
in the driver. The memory can be passed from userspace by dmabuf fd and
an offset or a VA. One of the possible usages is creating CQs that
reside in accelerator memory, allowing low latency asynchronous direct
polling from the accelerator device. Add a capability bit to reflect on
the feature support.
Reviewed-by: Daniel Kranzdorf <dkkranzd@amazon.com>
Reviewed-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://patch.msgid.link/20250708202308.24783-4-mrgolin@amazon.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In some cases drivers may need to check if a given umem is contiguous.
Add a helper function in core code so that drivers don't need to deal
with umem or scatter-gather lists structure.
Additionally add a helper for getting umem's start DMA address and use
it in other helper functions that open code it.
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://patch.msgid.link/20250708202308.24783-3-mrgolin@amazon.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add ioctl command attributes and a common handling for the option to
create CQs with memory buffers passed from userspace. When required
attributes are supplied, create umem and provide it for driver's use.
The extension enables creation of CQs on top of preallocated CPU
virtual or device memory buffers, by supplying VA or dmabuf fd, in a
common way.
Drivers can support this flow by initializing a new create_cq_umem fp
field in their ops struct, with a function that can handle the new
parameter.
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://patch.msgid.link/20250708202308.24783-2-mrgolin@amazon.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
