When hibernate with data center dGPUs, huge number of VRAM data will be
moved to shmem during dev_pm_ops.prepare(). These shmem pages take a lot
of system memory so that there's no enough free memory for creating the
hibernation image. This will cause hibernation fail and abort.
After dev_pm_ops.prepare(), call shrink_all_memory() to force move shmem
pages to swap disk and reclaim the pages, so that there's enough system
memory for hibernation image and less pages needed to copy to the image.
This patch can only flush and free about half shmem pages. It will be
better to flush and free more pages, even all of shmem pages, so that
there're less pages to be copied to the hibernation image and the overall
hibernation time can be reduced.
Signed-off-by: Samuel Zhang <guoqing.zhang@amd.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20250710062313.3226149-4-guoqing.zhang@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
When hibernate with data center dGPUs, huge number of VRAM BOs evicted
to GTT and takes too much system memory. This will cause hibernation
fail due to insufficient memory for creating the hibernation image.
Move GTT BOs to shmem in KMD, then shmem to swap disk in kernel
hibernation code to make room for hibernation image.
Signed-off-by: Samuel Zhang <guoqing.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250710062313.3226149-3-guoqing.zhang@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
This new api is used for hibernation to move GTT BOs to shmem after
VRAM eviction. shmem will be flushed to swap disk later to reduce
the system memory usage for hibernation.
Signed-off-by: Samuel Zhang <guoqing.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250710062313.3226149-2-guoqing.zhang@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The new HW queue object, as an internal iommufd object, wants to reuse the
struct iommufd_access to pin some iova range in the iopt.
However, an access generally takes the refcount of an ictx. So, in such an
internal case, a deadlock could happen when the release of the ictx has to
wait for the release of the access first when releasing a hw_queue object,
which could wait for the release of the ictx that is refcounted:
ictx --releases--> hw_queue --releases--> access
^ |
|_________________releases________________v
To address this, add a set of lightweight internal APIs to unlink the ictx
and the access, i.e. no ictx refcounting by the access:
ictx --releases--> hw_queue --releases--> access
Then, there's no point in setting the access->ictx. So simply define !ictx
as an flag for an internal use and add an inline helper.
Link: https://patch.msgid.link/r/d8d84bf99cbebec56034b57b966a3d431385b90d.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Extend the existing test_cmd/err_viommu_alloc helpers to accept optional
user data. And add a TEST_F for a loopback test.
Link: https://patch.msgid.link/r/8ceb64d30e9953f29270a7d341032ca439317271.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The new type of vIOMMU for tegra241-cmdqv driver needs a driver-specific
user data. So, add data_len/uptr to the iommu_viommu_alloc uAPI and pass
it in via the viommu_init iommu op.
Link: https://patch.msgid.link/r/2315b0e164b355746387e960745ac9154caec124.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Pranjal Shrivastava <praan@google.com>
Acked-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The new type of vIOMMU for tegra241-cmdqv allows user space VM to use one
of its virtual command queue HW resources exclusively. This requires user
space to mmap the corresponding MMIO page from kernel space for direct HW
control.
To forward the mmap info (offset and length), iommufd should add a driver
specific data structure to the IOMMUFD_CMD_VIOMMU_ALLOC ioctl, for driver
to output the info during the vIOMMU initialization back to user space.
Similar to the existing ioctls and their IOMMU handlers, add a user_data
to viommu_init op to bridge between iommufd and drivers.
Link: https://patch.msgid.link/r/90bd5637dab7f5507c7a64d2c4826e70431e45a4.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Similar to the iommu_copy_struct_from_user helper receiving data from the
user space, add an iommu_copy_struct_to_user helper to report output data
back to the user space data pointer.
Link: https://patch.msgid.link/r/fa292c2a730aadd77085ec3a8272360c96eabb9c.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Replace u32 to make it clear. No functional changes.
Also simplify the kdoc since the type itself is clear enough.
Link: https://patch.msgid.link/r/651c50dee8ab900f691202ef0204cd5a43fdd6a2.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The "id" is too general to get its meaning easily. Rename it explicitly to
"virt_id" and update the kdocs for readability. No functional changes.
Link: https://patch.msgid.link/r/1fac22d645e6ee555675726faf3798a68315b044.1752126748.git.nicolinc@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It turns out that the fixup from vlv_fixup_mipi_sequences() is necessary
for some DSI panel's with version 2 mipi-sequences too.
Specifically the Acer Iconia One 8 A1-840 (not to be confused with the
A1-840FHD which is different) has the following sequences:
BDB block 53 (1284 bytes) - MIPI sequence block:
Sequence block version v2
Panel 0 *
Sequence 2 - MIPI_SEQ_INIT_OTP
GPIO index 9, source 0, set 0 (0x00)
Delay: 50000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 6000 us
GPIO index 9, source 0, set 0 (0x00)
Delay: 6000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 25000 us
Send DCS: Port A, VC 0, LP, Type 39, Length 5, Data ff aa 55 a5 80
Send DCS: Port A, VC 0, LP, Type 39, Length 3, Data 6f 11 00
...
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 29
Delay: 120000 us
Sequence 4 - MIPI_SEQ_DISPLAY_OFF
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 28
Delay: 105000 us
Send DCS: Port A, VC 0, LP, Type 05, Length 2, Data 10 00
Delay: 10000 us
Sequence 5 - MIPI_SEQ_ASSERT_RESET
Delay: 10000 us
GPIO index 9, source 0, set 0 (0x00)
Notice how there is no MIPI_SEQ_DEASSERT_RESET, instead the deassert
is done at the beginning of MIPI_SEQ_INIT_OTP, which is exactly what
the fixup from vlv_fixup_mipi_sequences() fixes up.
Extend it to also apply to v2 sequences, this fixes the panel not working
on the Acer Iconia One 8 A1-840.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14605
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250703143824.7121-1-hansg@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 11895f3759)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
It turns out that the fixup from vlv_fixup_mipi_sequences() is necessary
for some DSI panel's with version 2 mipi-sequences too.
Specifically the Acer Iconia One 8 A1-840 (not to be confused with the
A1-840FHD which is different) has the following sequences:
BDB block 53 (1284 bytes) - MIPI sequence block:
Sequence block version v2
Panel 0 *
Sequence 2 - MIPI_SEQ_INIT_OTP
GPIO index 9, source 0, set 0 (0x00)
Delay: 50000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 6000 us
GPIO index 9, source 0, set 0 (0x00)
Delay: 6000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 25000 us
Send DCS: Port A, VC 0, LP, Type 39, Length 5, Data ff aa 55 a5 80
Send DCS: Port A, VC 0, LP, Type 39, Length 3, Data 6f 11 00
...
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 29
Delay: 120000 us
Sequence 4 - MIPI_SEQ_DISPLAY_OFF
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 28
Delay: 105000 us
Send DCS: Port A, VC 0, LP, Type 05, Length 2, Data 10 00
Delay: 10000 us
Sequence 5 - MIPI_SEQ_ASSERT_RESET
Delay: 10000 us
GPIO index 9, source 0, set 0 (0x00)
Notice how there is no MIPI_SEQ_DEASSERT_RESET, instead the deassert
is done at the beginning of MIPI_SEQ_INIT_OTP, which is exactly what
the fixup from vlv_fixup_mipi_sequences() fixes up.
Extend it to also apply to v2 sequences, this fixes the panel not working
on the Acer Iconia One 8 A1-840.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14605
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250703143824.7121-1-hansg@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
struct nouveau_sched contains a waitque needed to prevent
drm_sched_fini() from being called while there are still jobs pending.
Doing so so far would have caused memory leaks.
With the new memleak-free mode of operation switched on in
drm_sched_fini() by providing the callback nouveau_sched_cancel_job()
the waitque is not necessary anymore.
Remove the waitque.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-10-phasta@kernel.org
There is a new callback for always tearing the scheduler down in a
leak-free, deadlock-free manner.
Port Nouveau as its first user by providing the scheduler with a
callback that ensures the fence context gets killed in drm_sched_fini().
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-9-phasta@kernel.org
In order to implement a new DRM GPU scheduler callback in Nouveau, a
helper for obtaining a nouveau_fence from a dma_fence is necessary. Such
a helper exists already inside nouveau_fence.c, called from_fence().
Make that helper available to other C files with a more precise name.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-8-phasta@kernel.org
The scheduler unit tests now provide a new callback, cancel_job(). This
callback gets used by drm_sched_fini() for all still pending jobs to
cancel them.
Implement a new unit test to test this.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-6-phasta@kernel.org
The GPU Scheduler now supports a new callback, cancel_job(), which lets
the scheduler cancel all jobs which might not yet be freed when
drm_sched_fini() runs. Using this callback allows for significantly
simplifying the mock scheduler teardown code.
Implement the cancel_job() callback and adjust the code where necessary.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-5-phasta@kernel.org
Since its inception, the GPU scheduler can leak memory if the driver
calls drm_sched_fini() while there are still jobs in flight.
The simplest way to solve this in a backwards compatible manner is by
adding a new callback, drm_sched_backend_ops.cancel_job(), which
instructs the driver to signal the hardware fence associated with the
job. Afterwards, the scheduler can safely use the established free_job()
callback for freeing the job.
Implement the new backend_ops callback cancel_job().
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Link: https://lore.kernel.org/dri-devel/20250418113211.69956-1-tvrtko.ursulin@igalia.com/
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250710125412.128476-4-phasta@kernel.org
Remove always-on on generic ARM timer as the clock source provided by
STGEN is deactivated in low power mode, STOP1 by example.
Fixes: 5d30d03aaf ("arm64: dts: st: introduce stm32mp25 SoCs family")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250515151238.1.I85271ddb811a7cf73532fec90de7281cb24ce260@changeid
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add TRACE_GPU_MEM tracepoints for tracking global GPU memory usage.
These are required by VSR on Android 12+ for reporting GPU driver memory
allocations.
v5:
- Drop process_mem tracking
- Set the gpu_id field to dev->primary->index (Lucas, Tvrtko)
- Formatting cleanup under 80 columns
v3:
- Use now configurable CONFIG_TRACE_GPU_MEM instead of adding a
per-driver Kconfig (Lucas)
v2:
- Use u64 as preferred by checkpatch (Tvrtko)
- Fix errors in comments/Kconfig description (Tvrtko)
- drop redundant "CONFIG" in Kconfig
Signed-off-by: Juston Li <justonli@chromium.org>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250709192313.479336-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Install beacon protection keys in hardware for AP modes only if hardware
supports it, as indicated by the WMI service bit
WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
beacon protection uses keyidx 6 and 7.
Control this feature by setting bit 0 of feature_enable_bitmap when sending
the WMI_BCN_TMPL_CMDID command to firmware.
Check for the beacon protection enabled bit in both tx and non-tx profiles
for MBSSID cases. If set in either profile, enable the beacon protection
feature in firmware for transmitted vif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <karthikeyan.kathirvel@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250604101620.2948103-1-karthikeyan.kathirvel@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Packets delivered to mac80211 from the WBM error path currently do not
have the RX_FLAG_SKIP_MONITOR flag set in status->flag. As a result,
mac80211 performs unnecessary monitor mode checks on each packet, even
though these packets are not intended for monitor mode processing.
In regular rx path, this flag is explicitly set to avoid such overhead.
Align the WBM error path behavior by setting RX_FLAG_SKIP_MONITOR to
prevent redundant per-packet checks in mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605050135.1802902-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In order to ensure the HTT DebugFS structs shared with firmware have
matching alignment, the structs should be packed. Most of the structs
are correctly packed, however the following are not:
ath12k_htt_tx_pdev_rate_stats_tlv
ath12k_htt_rx_pdev_rate_stats_tlv
ath12k_htt_rx_pdev_rate_ext_stats_tlv
So pack those structs.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: ba42b22aa3 ("wifi: ath12k: Dump PDEV transmit rate HTT stats")
Fixes: a24cd75830 ("wifi: ath12k: Dump PDEV receive rate HTT stats")
Fixes: 7a3e8eec8d ("wifi: ath12k: Dump additional PDEV receive rate HTT stats")
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250702-debugfs_htt_packed-v1-1-07bd18b31e79@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The maximum bandwidth an interface can operate in is defined by the
configured country. However, currently, it is able to operate in
bandwidths greater than the allowed bandwidth. For example,
the Central African Republic (CF) supports a maximum bandwidth of 40 MHz
in both the 2 GHz and 5 GHz bands, but an interface is still able to
operate in bandwidths higher than 40 MHz. This issue arises because the
regulatory rules in the regd are not updated with these restrictions
received from firmware on the maximum bandwidth.
Hence, update the regulatory rules with unsupported bandwidth flags based
on the maximum bandwidth to ensure compliance with country-specific
regulations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Amith A <quic_amitajit@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250701135902.722851-1-quic_amitajit@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The mute led on this laptop is using ALC245 but requires a quirk to work
This patch enables the existing quirk for the device.
Tested on Victus 16-r0xxx Laptop. The LED behaviour works
as intended.
Cc: <stable@vger.kernel.org>
Signed-off-by: Edip Hazuri <edip@medip.dev>
Link: https://patch.msgid.link/20250710131812.27509-1-edip@medip.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hid-tools 0.10 fixes one inconvenience introduced by
commit 6a9e76f75c ("HID: multitouch: Disable touchpad
on firmware level while not in use")
This change added a new callback when a hid-nultitouch device is opened
or closed to put the underlying device into a given operating mode.
However, in the test cases, that means that while the single threaded
test is run, it opens the device but has to react to the device while
the open() is still running. hid-tools now implements a minimal thread
to circumvent this.
This makes the HID kernel tests in sync with hid-tools 0.10.
This has the net effect of running the full HID python testsuite in 6
minutes instead of 1 hour.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://patch.msgid.link/20250709-wip-fix-ci-v1-3-b7df4c271cf8@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Instead of backporting one by one each commits, let's pull them in bulk
and refer to the hid-tools project for a detailed history.
The short summary is:
- make use of dataclass when possible, to avoid tuples
- wacom: remove unused uhdev parameter
- various small fixes not worth mentioning
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://patch.msgid.link/20250709-wip-fix-ci-v1-2-b7df4c271cf8@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
We aim at syncing with the hid-tools repo on
gitlab.freedesktop.org/libevdev/hid-tools. One of the commits is this
mechanical formatting, so pull it over here so changes are not hidden by
those.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://patch.msgid.link/20250709-wip-fix-ci-v1-1-b7df4c271cf8@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Wire up suspend/resume handles for I2C controller to match its power
state with SGUnit.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Karthik Poosa <karthik.poosa@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250701122252.2590230-5-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Adding adaption/glue layer where the I2C host adapter
(Synopsys DesignWare I2C adapter) and the I2C clients (the
microcontroller units) are enumerated.
The microcontroller units (MCU) that are attached to the GPU
depend on the OEM. The initially supported MCU will be the
Add-In Management Controller (AMC).
Co-developed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250701122252.2590230-4-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo fixed the co-developed tags and SPDX format in the .c file]
The regmap is coming from the parent also in case of Xe
GPUs. Reusing the Wangxun quirk for that.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250701122252.2590230-3-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo fixed the co-developed tags while merging]
The irq resource itself can be used as a generic way to
determine when polling is needed.
This not only removes the need for special additional device
properties that would soon be needed when the platform may
or may not have the irq, but it also removes the need to
check the platform in the first place in order to determine
is polling needed or not.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250701122252.2590230-2-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
NDI (Northern Digital Inc.) is introducing a new product called the
EMGUIDE GEMINI that will use an FTDI chip for USB serial communications.
Add the NDI EMGUIDE GEMINI product ID that uses the NDI Vendor ID
rather than the FTDI Vendor ID, unlike older products.
Signed-off-by: Ryan Mann <rmann@ndigital.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Since we are already using reusable buffer objects from the GuC
buffer cache, we can directly write into their CPU pointers and
spare unnecessary temporary allocation.
While around, also make sure to clear obtained buffer, to avoid
sending some stale data.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250702142504.1656-1-michal.wajdeczko@intel.com
Rosen Penev says:
====================
net: dsa: rzn1_a5psw: add COMPILE_TEST
Allows the various bots to test compilation. Also threw in a small devm
conversion for enabling clocks.
====================
Link: https://patch.msgid.link/20250708014144.2514-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The remove function has these in the wrong order. The switch should be
unregistered last. Simpler to use devm so that the right thing is done.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20250708014144.2514-3-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There's no architecture specific requirement for it to compile. Allows
the bots to test compilation properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250708014144.2514-2-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In 7e9b231c40 ("KVM: selftests: Add a KVM_IRQFD test to verify
uniqueness requirements") we added a test for the newly added irqfd
support but since this feature works with eventfds it won't work unless
the kernel has been built wth eventfd support. Add CONFIG_EVENTFD to
the list of required options for the KVM selftests.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250710-kvm-selftests-eventfd-config-v1-1-78c276e4b80f@kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
During BMC firmware upgrades on live systems, the ipmi_msghandler
generates excessive "BMC returned incorrect response" warnings
while the BMC is temporarily offline. This can flood system logs
in large deployments.
Replace dev_warn() with dev_warn_ratelimited() to throttle these
warnings and prevent log spam during BMC maintenance operations.
Signed-off-by: Breno Leitao <leitao@debian.org>
Message-ID: <20250710-ipmi_ratelimit-v1-1-6d417015ebe9@debian.org>
Signed-off-by: Corey Minyard <corey@minyard.net>
The function opencodes the for_each_cpu_from() by using an open for-loop.
Fix that in sake of readability.
While there, drop the 'valid' variable as it's pretty useless here.
Signed-off-by: Yury Norov [NVIDIA] <yury.norov@gmail.com>
Link: https://patch.msgid.link/20250604213908.27819-1-yury.norov@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit fbfb649870 ("dt-bindings: firmware: stratix10: Convert to
json-schema") renames intel,stratix10-svc.txt to intel,stratix10-svc.yaml
in Documentation/devicetree/bindings/firmware/ as part of this dt-binding
conversion, but misses to adjust the file entry in INTEL STRATIX10 FIRMWARE
DRIVERS.
Adjust the file entry after the conversion.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20250512134332.36366-1-lukas.bulwahn@redhat.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
This patch provides a setsockopt method to let applications leverage to
adjust how many descs to be handled at most in one send syscall. It
mitigates the situation where the default value (32) that is too small
leads to higher frequency of triggering send syscall.
Considering the prosperity/complexity the applications have, there is no
absolutely ideal suggestion fitting all cases. So keep 32 as its default
value like before.
The patch does the following things:
- Add XDP_MAX_TX_SKB_BUDGET socket option.
- Set max_tx_budget to 32 by default in the initialization phase as a
per-socket granular control.
- Set the range of max_tx_budget as [32, xs->tx->nentries].
The idea behind this comes out of real workloads in production. We use a
user-level stack with xsk support to accelerate sending packets and
minimize triggering syscalls. When the packets are aggregated, it's not
hard to hit the upper bound (namely, 32). The moment user-space stack
fetches the -EAGAIN error number passed from sendto(), it will loop to try
again until all the expected descs from tx ring are sent out to the driver.
Enlarging the XDP_MAX_TX_SKB_BUDGET value contributes to less frequency of
sendto() and higher throughput/PPS.
Here is what I did in production, along with some numbers as follows:
For one application I saw lately, I suggested using 128 as max_tx_budget
because I saw two limitations without changing any default configuration:
1) XDP_MAX_TX_SKB_BUDGET, 2) socket sndbuf which is 212992 decided by
net.core.wmem_default. As to XDP_MAX_TX_SKB_BUDGET, the scenario behind
this was I counted how many descs are transmitted to the driver at one
time of sendto() based on [1] patch and then I calculated the
possibility of hitting the upper bound. Finally I chose 128 as a
suitable value because 1) it covers most of the cases, 2) a higher
number would not bring evident results. After twisting the parameters,
a stable improvement of around 4% for both PPS and throughput and less
resources consumption were found to be observed by strace -c -p xxx:
1) %time was decreased by 7.8%
2) error counter was decreased from 18367 to 572
[1]: https://lore.kernel.org/all/20250619093641.70700-1-kerneljasonxing@gmail.com/
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250704160138.48677-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
